From patchwork Sat May 30 08:10:06 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Peng Fan X-Patchwork-Id: 246866 List-Id: U-Boot discussion From: peng.fan at nxp.com (Peng Fan) Date: Sat, 30 May 2020 16:10:06 +0800 Subject: [PATCH V2 1/7] driver: ddr: imx: skip ddr_ss_gpr config on imx8mn In-Reply-To: <20200530081012.26573-1-peng.fan@nxp.com> References: <20200530081012.26573-1-peng.fan@nxp.com> Message-ID: <20200530081012.26573-2-peng.fan@nxp.com> From: Jacky Bai There is no DDR_SS_GPR0 exits on i.MX8MN, so skip setting this register on i.MX8MN. Signed-off-by: Jacky Bai Signed-off-by: Peng Fan --- drivers/ddr/imx/imx8m/ddr_init.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/ddr/imx/imx8m/ddr_init.c b/drivers/ddr/imx/imx8m/ddr_init.c index af8c1427d2..ba5ae05035 100644 --- a/drivers/ddr/imx/imx8m/ddr_init.c +++ b/drivers/ddr/imx/imx8m/ddr_init.c @@ -73,7 +73,7 @@ int ddr_init(struct dram_timing_info *dram_timing) /* if ddr type is LPDDR4, do it */ tmp = reg32_read(DDRC_MSTR(0)); - if (tmp & (0x1 << 5)) + if (tmp & (0x1 << 5) && !is_imx8mn()) reg32_write(DDRC_DDR_SS_GPR0, 0x01); /* LPDDR4 mode */ /* determine the initial boot frequency */ From patchwork Sat May 30 08:10:07 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Peng Fan X-Patchwork-Id: 246867 List-Id: U-Boot discussion From: peng.fan at nxp.com (Peng Fan) Date: Sat, 30 May 2020 16:10:07 +0800 Subject: [PATCH V2 2/7] driver: ddr: imx: correct the pwrctl setting of selfref_en on imx8m In-Reply-To: <20200530081012.26573-1-peng.fan@nxp.com> References: <20200530081012.26573-1-peng.fan@nxp.com> Message-ID: <20200530081012.26573-3-peng.fan@nxp.com> From: Jacky Bai The 'selfref_en' should be bit'0', so correct the setting to enable the auto self-refresh. Reviewed-by: Jian Li Reviewed-by: Ye Li Signed-off-by: Jacky Bai Signed-off-by: Peng Fan --- drivers/ddr/imx/imx8m/ddr_init.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/ddr/imx/imx8m/ddr_init.c b/drivers/ddr/imx/imx8m/ddr_init.c index ba5ae05035..06b4341b11 100644 --- a/drivers/ddr/imx/imx8m/ddr_init.c +++ b/drivers/ddr/imx/imx8m/ddr_init.c @@ -162,7 +162,7 @@ int ddr_init(struct dram_timing_info *dram_timing) /* Step26: Set back register in Step4 to the original values if desired */ reg32_write(DDRC_RFSHCTL3(0), 0x0000000); /* enable selfref_en by default */ - setbits_le32(DDRC_PWRCTL(0), 0x1 << 3); + setbits_le32(DDRC_PWRCTL(0), 0x1); /* enable port 0 */ reg32_write(DDRC_PCTRL_0(0), 0x00000001); From patchwork Sat May 30 08:10:08 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Peng Fan X-Patchwork-Id: 246868 List-Id: U-Boot discussion From: peng.fan at nxp.com (Peng Fan) Date: Sat, 30 May 2020 16:10:08 +0800 Subject: [PATCH V2 3/7] drivers: ddr: imx8mp: Add inline ECC feature support In-Reply-To: <20200530081012.26573-1-peng.fan@nxp.com> References: <20200530081012.26573-1-peng.fan@nxp.com> Message-ID: <20200530081012.26573-4-peng.fan@nxp.com> From: Sherry Sun the DRAM Controller in i.MX8MP will support a feature called "Inline ECC". This is supported for all 3 supported DRAM technologies (LPDDR4, DDR4 and DDR3L). When this feature is enabled by software, the DRAM Controller reserves 12.5% of DRAM capacity for ECC information, and presents only the non-ECC portion (lower 87.5% of the installed capacity of DRAM) to the rest of the SoC. The DRAM memory can be divided into 8 regions so that if a use case only requires ECC protection on a subset of memory, then only that subset of memory need support inline ECC. If this occurs, then there is no performance penalty accessing the non-ECC-protected memory (no need to access ECC for this portion of the memory map). This is all configured with the DRAM Controller. Signed-off-by: Sherry Sun Signed-off-by: Peng Fan --- arch/arm/include/asm/arch-imx8m/ddr.h | 7 ++++ drivers/ddr/imx/imx8m/Kconfig | 7 ++++ drivers/ddr/imx/imx8m/ddr_init.c | 72 +++++++++++++++++++++++++++++++++++ 3 files changed, 86 insertions(+) diff --git a/arch/arm/include/asm/arch-imx8m/ddr.h b/arch/arm/include/asm/arch-imx8m/ddr.h index 7a2a2d8edc..04c9c962cf 100644 --- a/arch/arm/include/asm/arch-imx8m/ddr.h +++ b/arch/arm/include/asm/arch-imx8m/ddr.h @@ -529,6 +529,8 @@ enum msg_response { #define DDRC_SBRWDATA0(X) (DDRC_IPS_BASE_ADDR(X) + 0xf2c) #define DDRC_SBRWDATA1(X) (DDRC_IPS_BASE_ADDR(X) + 0xf30) #define DDRC_PDCH(X) (DDRC_IPS_BASE_ADDR(X) + 0xf34) +#define DDRC_SBRSTART0(X) (DDRC_IPS_BASE_ADDR(X) + 0xf38) +#define DDRC_SBRRANGE0(X) (DDRC_IPS_BASE_ADDR(X) + 0xf40) #define DDRC_FREQ1_DERATEEN(X) (DDRC_IPS_BASE_ADDR(X) + 0x2020) #define DDRC_FREQ1_DERATEINT(X) (DDRC_IPS_BASE_ADDR(X) + 0x2024) @@ -708,6 +710,11 @@ int ddr_cfg_phy(struct dram_timing_info *timing_info); void load_lpddr4_phy_pie(void); void ddrphy_trained_csr_save(struct dram_cfg_param *param, unsigned int num); void dram_config_save(struct dram_timing_info *info, unsigned long base); +void board_dram_ecc_scrub(void); +void ddrc_inline_ecc_scrub(unsigned int start_address, + unsigned int range_address); +void ddrc_inline_ecc_scrub_end(unsigned int start_address, + unsigned int range_address); /* utils function for ddr phy training */ int wait_ddrphy_training_complete(void); diff --git a/drivers/ddr/imx/imx8m/Kconfig b/drivers/ddr/imx/imx8m/Kconfig index 5bf61eb258..a5f5524fbe 100644 --- a/drivers/ddr/imx/imx8m/Kconfig +++ b/drivers/ddr/imx/imx8m/Kconfig @@ -29,4 +29,11 @@ config SAVED_DRAM_TIMING_BASE info into memory for low power use. OCRAM_S is used for this purpose on i.MX8MM. default 0x180000 + +config IMX8M_DRAM_INLINE_ECC + bool "imx8mp inline ECC" + depends on IMX8MP && IMX8M_LPDDR4 + help + Select this config if you want to use inline ecc feature for + imx8mp-evk board. endmenu diff --git a/drivers/ddr/imx/imx8m/ddr_init.c b/drivers/ddr/imx/imx8m/ddr_init.c index 06b4341b11..f573a778d9 100644 --- a/drivers/ddr/imx/imx8m/ddr_init.c +++ b/drivers/ddr/imx/imx8m/ddr_init.c @@ -20,6 +20,76 @@ void ddr_cfg_umctl2(struct dram_cfg_param *ddrc_cfg, int num) } } +#ifdef CONFIG_IMX8M_DRAM_INLINE_ECC +void ddrc_inline_ecc_scrub(unsigned int start_address, + unsigned int range_address) +{ + unsigned int tmp; + + /* Step1: Enable quasi-dynamic programming */ + reg32_write(DDRC_SWCTL(0), 0x00000000); + /* Step2: Set ECCCFG1.ecc_parity_region_lock to 1 */ + reg32setbit(DDRC_ECCCFG1(0), 0x4); + /* Step3: Block the AXI ports from taking the transaction */ + reg32_write(DDRC_PCTRL_0(0), 0x0); + /* Step4: Set scrub start address */ + reg32_write(DDRC_SBRSTART0(0), start_address); + /* Step5: Set scrub range address */ + reg32_write(DDRC_SBRRANGE0(0), range_address); + /* Step6: Set scrub_mode to write */ + reg32_write(DDRC_SBRCTL(0), 0x00000014); + /* Step7: Set the desired pattern through SBRWDATA0 registers */ + reg32_write(DDRC_SBRWDATA0(0), 0x55aa55aa); + /* Step8: Enable the SBR by programming SBRCTL.scrub_en=1 */ + reg32setbit(DDRC_SBRCTL(0), 0x0); + /* Step9: Poll SBRSTAT.scrub_done=1 */ + tmp = reg32_read(DDRC_SBRSTAT(0)); + while (tmp != 0x00000002) + tmp = reg32_read(DDRC_SBRSTAT(0)) & 0x2; + /* Step10: Poll SBRSTAT.scrub_busy=0 */ + tmp = reg32_read(DDRC_SBRSTAT(0)); + while (tmp != 0x0) + tmp = reg32_read(DDRC_SBRSTAT(0)) & 0x1; + /* Step11: Disable SBR by programming SBRCTL.scrub_en=0 */ + clrbits_le32(DDRC_SBRCTL(0), 0x1); + /* Step12: Prepare for normal scrub operation(Read) and set scrub_interval*/ + reg32_write(DDRC_SBRCTL(0), 0x100); + /* Step13: Enable the SBR by programming SBRCTL.scrub_en=1 */ + reg32_write(DDRC_SBRCTL(0), 0x101); + /* Step14: Enable AXI ports by programming */ + reg32_write(DDRC_PCTRL_0(0), 0x1); + /* Step15: Disable quasi-dynamic programming */ + reg32_write(DDRC_SWCTL(0), 0x00000001); +} + +void ddrc_inline_ecc_scrub_end(unsigned int start_address, + unsigned int range_address) +{ + /* Step1: Enable quasi-dynamic programming */ + reg32_write(DDRC_SWCTL(0), 0x00000000); + /* Step2: Block the AXI ports from taking the transaction */ + reg32_write(DDRC_PCTRL_0(0), 0x0); + /* Step3: Set scrub start address */ + reg32_write(DDRC_SBRSTART0(0), start_address); + /* Step4: Set scrub range address */ + reg32_write(DDRC_SBRRANGE0(0), range_address); + /* Step5: Disable SBR by programming SBRCTL.scrub_en=0 */ + clrbits_le32(DDRC_SBRCTL(0), 0x1); + /* Step6: Prepare for normal scrub operation(Read) and set scrub_interval */ + reg32_write(DDRC_SBRCTL(0), 0x100); + /* Step7: Enable the SBR by programming SBRCTL.scrub_en=1 */ + reg32_write(DDRC_SBRCTL(0), 0x101); + /* Step8: Enable AXI ports by programming */ + reg32_write(DDRC_PCTRL_0(0), 0x1); + /* Step9: Disable quasi-dynamic programming */ + reg32_write(DDRC_SWCTL(0), 0x00000001); +} +#endif + +void __weak board_dram_ecc_scrub(void) +{ +} + int ddr_init(struct dram_timing_info *dram_timing) { unsigned int tmp, initial_drate, target_freq; @@ -168,6 +238,8 @@ int ddr_init(struct dram_timing_info *dram_timing) reg32_write(DDRC_PCTRL_0(0), 0x00000001); debug("DDRINFO: ddrmix config done\n"); + board_dram_ecc_scrub(); + /* save the dram timing config into memory */ dram_config_save(dram_timing, CONFIG_SAVED_DRAM_TIMING_BASE);