From patchwork Sat May 2 08:59:35 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Stefan Roese X-Patchwork-Id: 244775 List-Id: U-Boot discussion From: sr at denx.de (Stefan Roese) Date: Sat, 2 May 2020 10:59:35 +0200 Subject: [PATCH v1 01/10] mips: octeon: Initial minimal support for the Marvell Octeon SoC In-Reply-To: <20200502085944.13444-1-sr@denx.de> References: <20200502085944.13444-1-sr@denx.de> Message-ID: <20200502085944.13444-2-sr@denx.de> From: Aaron Williams This patch adds very basic support for the Octeon III SoCs. Only CFI parallel NOR flash and UART is supported for now. Please note that the basic Octeon port does not include the DDR3/4 initialization yet. This will be added in some follow-up patches later. To still use U-Boot on with this port, the L2 cache (4MiB on Octeon III CN73xx) is used as RAM. This way, U-Boot can boot to the prompt on such boards. Signed-off-by: Aaron Williams Signed-off-by: Stefan Roese --- MAINTAINERS | 6 + arch/Kconfig | 1 + arch/mips/Kconfig | 49 +- arch/mips/Makefile | 7 + arch/mips/cpu/Makefile | 4 +- arch/mips/include/asm/arch-octeon/cavm-reg.h | 42 + arch/mips/include/asm/arch-octeon/clock.h | 24 + arch/mips/mach-octeon/Kconfig | 92 ++ arch/mips/mach-octeon/Makefile | 10 + arch/mips/mach-octeon/clock.c | 22 + arch/mips/mach-octeon/cpu.c | 55 + arch/mips/mach-octeon/dram.c | 27 + arch/mips/mach-octeon/include/ioremap.h | 30 + arch/mips/mach-octeon/start.S | 1241 ++++++++++++++++++ 14 files changed, 1608 insertions(+), 2 deletions(-) create mode 100644 arch/mips/include/asm/arch-octeon/cavm-reg.h create mode 100644 arch/mips/include/asm/arch-octeon/clock.h create mode 100644 arch/mips/mach-octeon/Kconfig create mode 100644 arch/mips/mach-octeon/Makefile create mode 100644 arch/mips/mach-octeon/clock.c create mode 100644 arch/mips/mach-octeon/cpu.c create mode 100644 arch/mips/mach-octeon/dram.c create mode 100644 arch/mips/mach-octeon/include/ioremap.h create mode 100644 arch/mips/mach-octeon/start.S diff --git a/MAINTAINERS b/MAINTAINERS index 66f0b07263..29f2d7328c 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -749,6 +749,12 @@ M: Ezequiel Garcia S: Maintained F: arch/mips/mach-jz47xx/ +MIPS Octeon +M: Aaron Williams +S: Maintained +F: arch/mips/mach-octeon/ +F: arch/mips/include/asm/arch-octeon/ + MMC M: Peng Fan S: Maintained diff --git a/arch/Kconfig b/arch/Kconfig index 91e049b322..1cd3e1dc0b 100644 --- a/arch/Kconfig +++ b/arch/Kconfig @@ -37,6 +37,7 @@ config MICROBLAZE config MIPS bool "MIPS architecture" + select CREATE_ARCH_SYMLINK select HAVE_ARCH_IOREMAP select HAVE_PRIVATE_LIBGCC select SUPPORT_OF_CONTROL diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig index 48e754cc46..3c7f3eb94f 100644 --- a/arch/mips/Kconfig +++ b/arch/mips/Kconfig @@ -106,6 +106,24 @@ config ARCH_JZ47XX select OF_CONTROL select DM +config ARCH_OCTEON + bool "Support Marvell Octeon CN7xxx platforms" + select DISPLAY_CPUINFO + select DMA_ADDR_T_64BIT + select DM + select DM_SERIAL + select MIPS_CACHE_COHERENT + select MIPS_INIT_STACK_IN_SRAM + select MIPS_L2_CACHE + select MIPS_TUNE_OCTEON3 + select ROM_EXCEPTION_VECTORS + select SUPPORTS_BIG_ENDIAN + select SUPPORTS_CPU_MIPS64_OCTEON + select PHYS_64BIT + select OF_CONTROL + select OF_LIVE + imply CMD_DM + config MACH_PIC32 bool "Support Microchip PIC32" select DM @@ -160,6 +178,7 @@ source "arch/mips/mach-bmips/Kconfig" source "arch/mips/mach-jz47xx/Kconfig" source "arch/mips/mach-pic32/Kconfig" source "arch/mips/mach-mtmips/Kconfig" +source "arch/mips/mach-octeon/Kconfig" if MIPS @@ -233,6 +252,14 @@ config CPU_MIPS64_R6 Choose this option to build a kernel for release 6 or later of the MIPS64 architecture. +config CPU_MIPS64_OCTEON + bool "Marvell Octeon series of CPUs" + depends on SUPPORTS_CPU_MIPS64_OCTEON + select 64BIT + help + Choose this option for Marvell Octeon CPUs. These CPUs are between + MIPS64 R5 and R6 with other extensions. + endchoice menu "General setup" @@ -261,7 +288,7 @@ config MIPS_CM_BASE config MIPS_CACHE_INDEX_BASE hex "Index base address for cache initialisation" default 0x80000000 if CPU_MIPS32 - default 0xffffffff80000000 if CPU_MIPS64 + default 0xFFFFFFFFC0000000 if ARCH_OCTEON help This is the base address for a memory block, which is used for initialising the cache lines. This is also the base address of a memory @@ -342,6 +369,14 @@ config SPL_LOADER_SUPPORT help Enable this option if you want to use SPL loaders without DM enabled. +config MIPS_CACHE_COHERENT + bool "Set if MIPS processor is cache coherent" + help + Enable this if the MIPS architecture is cache coherent like the + Marvell Octeon series of SoCs. When this is set, cache flushes + and invalidates only flush the write buffer since the hardware + maintains cache coherency. + endmenu menu "OS boot interface" @@ -398,6 +433,9 @@ config SUPPORTS_CPU_MIPS64_R2 config SUPPORTS_CPU_MIPS64_R6 bool +config SUPPORTS_CPU_MIPS64_OCTEON + bool + config CPU_MIPS32 bool default y if CPU_MIPS32_R1 || CPU_MIPS32_R2 || CPU_MIPS32_R6 @@ -405,6 +443,7 @@ config CPU_MIPS32 config CPU_MIPS64 bool default y if CPU_MIPS64_R1 || CPU_MIPS64_R2 || CPU_MIPS64_R6 + default y if CPU_MIPS64_OCTEON config MIPS_TUNE_4KC bool @@ -421,6 +460,9 @@ config MIPS_TUNE_34KC config MIPS_TUNE_74KC bool +config MIPS_TUNE_OCTEON3 + bool + config 32BIT bool @@ -453,6 +495,11 @@ config MIPS_SRAM_INIT before it can be used. If enabled, a function mips_sram_init() will be called just before setup_stack_gd. +config DMA_ADDR_T_64BIT + bool + help + Select this to enable 64-bit DMA addressing + config SYS_DCACHE_SIZE int default 0 diff --git a/arch/mips/Makefile b/arch/mips/Makefile index af3f227436..fa1ba7855a 100644 --- a/arch/mips/Makefile +++ b/arch/mips/Makefile @@ -1,6 +1,10 @@ # SPDX-License-Identifier: GPL-2.0+ +ifneq ($(CONFIG_ARCH_OCTEON),y) head-y := arch/mips/cpu/start.o +else +head-y := arch/mips/mach-octeon/start.o +endif ifeq ($(CONFIG_SPL_BUILD),y) ifneq ($(CONFIG_SPL_START_S_PATH),) @@ -17,6 +21,7 @@ machine-$(CONFIG_ARCH_JZ47XX) += jz47xx machine-$(CONFIG_MACH_PIC32) += pic32 machine-$(CONFIG_ARCH_MTMIPS) += mtmips machine-$(CONFIG_ARCH_MSCC) += mscc +machine-${CONFIG_ARCH_OCTEON} += octeon machdirs := $(patsubst %,arch/mips/mach-%/,$(machine-y)) libs-y += $(machdirs) @@ -30,6 +35,7 @@ arch-$(CONFIG_CPU_MIPS32_R6) += -march=mips32r6 -Wa,-mips32r6 arch-$(CONFIG_CPU_MIPS64_R1) += -march=mips64 -Wa,-mips64 arch-$(CONFIG_CPU_MIPS64_R2) += -march=mips64r2 -Wa,-mips64r2 arch-$(CONFIG_CPU_MIPS64_R6) += -march=mips64r6 -Wa,-mips64r6 +arch-${CONFIG_CPU_MIPS64_OCTEON} += -march=octeon3 # Allow extra optimization for specific CPUs/SoCs tune-$(CONFIG_MIPS_TUNE_4KC) += -mtune=4kc @@ -37,6 +43,7 @@ tune-$(CONFIG_MIPS_TUNE_14KC) += -mtune=14kc tune-$(CONFIG_MIPS_TUNE_24KC) += -mtune=24kc tune-$(CONFIG_MIPS_TUNE_34KC) += -mtune=34kc tune-$(CONFIG_MIPS_TUNE_74KC) += -mtune=74kc +tune-${CONFIG_MIPS_TUNE_OCTEON3} += -mtune=octeon3 # Include default header files cflags-y += -I$(srctree)/arch/mips/include/asm/mach-generic diff --git a/arch/mips/cpu/Makefile b/arch/mips/cpu/Makefile index 6df7bb4e48..732015d6f3 100644 --- a/arch/mips/cpu/Makefile +++ b/arch/mips/cpu/Makefile @@ -1,6 +1,8 @@ # SPDX-License-Identifier: GPL-2.0+ -extra-y = start.o +ifneq ($(CONFIG_ARCH_OCTEON),y) +extra-y = start.o +endif obj-y += time.o obj-y += interrupts.o diff --git a/arch/mips/include/asm/arch-octeon/cavm-reg.h b/arch/mips/include/asm/arch-octeon/cavm-reg.h new file mode 100644 index 0000000000..b961e54956 --- /dev/null +++ b/arch/mips/include/asm/arch-octeon/cavm-reg.h @@ -0,0 +1,42 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (C) 2020 Marvell International Ltd. + */ + +#ifndef __CAVM_REG_H__ + +/* Register offsets */ +#define CAVM_CIU_FUSE ((u64 *)0x80010100000001a0) +#define CAVM_MIO_BOOT_REG_CFG0 ((u64 *)0x8001180000000000) +#define CAVM_RST_BOOT ((u64 *)0x8001180006001600) + +/* Register structs */ + +/** + * Register (RSL) rst_boot + * + * RST Boot Register + */ +union cavm_rst_boot { + u64 u; + struct cavm_rst_boot_s { + u64 chipkill : 1; + u64 jtcsrdis : 1; + u64 ejtagdis : 1; + u64 romen : 1; + u64 ckill_ppdis : 1; + u64 jt_tstmode : 1; + u64 vrm_err : 1; + u64 reserved_37_56 : 20; + u64 c_mul : 7; + u64 pnr_mul : 6; + u64 reserved_21_23 : 3; + u64 lboot_oci : 3; + u64 lboot_ext : 6; + u64 lboot : 10; + u64 rboot : 1; + u64 rboot_pin : 1; + } s; +}; + +#endif /* __CAVM_REG_H__ */ diff --git a/arch/mips/include/asm/arch-octeon/clock.h b/arch/mips/include/asm/arch-octeon/clock.h new file mode 100644 index 0000000000..a844a222c9 --- /dev/null +++ b/arch/mips/include/asm/arch-octeon/clock.h @@ -0,0 +1,24 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (C) 2018, 2019 Marvell International Ltd. + * + * https://spdx.org/licenses + */ + +#ifndef __CLOCK_H__ + +/** System PLL reference clock */ +#define PLL_REF_CLK 50000000 /* 50 MHz */ +#define NS_PER_REF_CLK_TICK (1000000000 / PLL_REF_CLK) + +/** + * Returns the I/O clock speed in Hz + */ +u64 octeon_get_io_clock(void); + +/** + * Returns the core clock speed in Hz + */ +u64 octeon_get_core_clock(void); + +#endif /* __CLOCK_H__ */ diff --git a/arch/mips/mach-octeon/Kconfig b/arch/mips/mach-octeon/Kconfig new file mode 100644 index 0000000000..67fcb6058c --- /dev/null +++ b/arch/mips/mach-octeon/Kconfig @@ -0,0 +1,92 @@ +menu "Octeon platforms" + depends on ARCH_OCTEON + +config SYS_SOC + string + default "octeon" + +config OCTEON_CN7XXX + bool "Octeon CN7XXX SoC" + +config OCTEON_CN70XX + bool "Octeon CN70XX SoC" + select OCTEON_CN7XXX + +config OCTEON_CN73XX + bool "Octeon CN73XX SoC" + select OCTEON_CN7XXX + +config OCTEON_CN78XX + bool "Octeon CN78XX SoC" + select OCTEON_CN7XXX + +choice + prompt "Octeon MIPS family select" + +config SOC_OCTEON2 + bool "Octeon II family" + help + This selects the Octeon II SoC family + +config SOC_OCTEON3 + bool "Octeon III family" + help + This selects the Octeon III SoC family CN70xx, CN73XX, CN78xx + and CNF75XX. + +endchoice + +config SYS_DCACHE_SIZE + default 32768 + +config SYS_DCACHE_LINE_SIZE + default 128 + +config SYS_ICACHE_SIZE + default 79872 + +config SYS_ICACHE_LINE_SIZE + default 128 + +config OCTEON_BIG_STACK_SIZE + hex + default 0x4000 + help + This enables a larger stack needed for Octeon 3 DRAM initialization. + If this is disabled then a part of the L1 cache will be reserved for + the stack, resulting in a smaller image. If this is true then + a portion of the TEXT address space will be reserved for the stack. + Note that this requires that U-Boot MUST be able to fit entirely + within the L2 cache and cannot be executed from a parallel NOR flash. + The default size is 16KiB. + +config OCTEON_COPY_FROM_FLASH_TO_L2 + bool + default y + help + Set this for U-Boot to attempt to copy itself from flash memory into + the L2 cache. This significantly improvess the boot performance. + +config OCTEON_L2_MEMCPY_IN_CACHE + bool + default y + help + If this is set then the memcpy code that is used to copy U-Boot from + the flash to the L2 cache is written to the L2 cache. This + significantly speeds up the memcpy operation. + +config OCTEON_L2_UBOOT_ADDR + hex + default 0xffffffff81000000 + help + This specifies the address where U-Boot will be copied into the L2 + cache. + +config OCTEON_L2_MEMCPY_ADDR + hex + default 0xffffffff81400000 + help + This specifies where U-Boot will place the memcpy routine used for + copying U-Boot from flash to L2 cache. + +endmenu diff --git a/arch/mips/mach-octeon/Makefile b/arch/mips/mach-octeon/Makefile new file mode 100644 index 0000000000..a5fda682a7 --- /dev/null +++ b/arch/mips/mach-octeon/Makefile @@ -0,0 +1,10 @@ +# (C) Copyright 2019 Marvell, Inc. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +extra-y = start.o + +obj-y += clock.o +obj-y += cpu.o +obj-y += dram.o diff --git a/arch/mips/mach-octeon/clock.c b/arch/mips/mach-octeon/clock.c new file mode 100644 index 0000000000..6e32008641 --- /dev/null +++ b/arch/mips/mach-octeon/clock.c @@ -0,0 +1,22 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2018, 2019 Marvell International Ltd. + */ + +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +int octeon_get_timer_freq(void) +{ + return gd->cpu_clk; +} + +/** + * Returns the I/O clock speed in Hz + */ +u64 octeon_get_io_clock(void) +{ + return gd->bus_clk; +} diff --git a/arch/mips/mach-octeon/cpu.c b/arch/mips/mach-octeon/cpu.c new file mode 100644 index 0000000000..a1373c6d56 --- /dev/null +++ b/arch/mips/mach-octeon/cpu.c @@ -0,0 +1,55 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2020 Marvell International Ltd. + */ + +#include +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +static int get_clocks(void) +{ + const u64 ref_clock = PLL_REF_CLK; + union cavm_rst_boot rst_boot; + + rst_boot.u = ioread64(CAVM_RST_BOOT); + gd->cpu_clk = ref_clock * rst_boot.s.c_mul; + gd->bus_clk = ref_clock * rst_boot.s.pnr_mul; + + debug("%s: cpu: %lu, bus: %lu\n", __func__, gd->cpu_clk, gd->bus_clk); + + return 0; +} + +/* Early mach init code run from flash */ +int mach_cpu_init(void) +{ + /* Remap boot-bus 0x1fc0.0000 -> 0x1f40.0000 */ + /* ToDo: Move this to an early running bus (bootbus) DM driver */ + clrsetbits_be64(CAVM_MIO_BOOT_REG_CFG0, 0xffff, 0x1f40); + + /* Get clocks and store them in GD */ + get_clocks(); + + return 0; +} + +/** + * Returns number of cores + * + * @return number of CPU cores for the specified node + */ +static int cavm_octeon_num_cores(void) +{ + return fls64(ioread64(CAVM_CIU_FUSE) & 0xffffffffffff); +} + +int print_cpuinfo(void) +{ + printf("SoC: Octeon CN73xx (%d cores)\n", cavm_octeon_num_cores()); + + return 0; +} diff --git a/arch/mips/mach-octeon/dram.c b/arch/mips/mach-octeon/dram.c new file mode 100644 index 0000000000..c16a73e8e6 --- /dev/null +++ b/arch/mips/mach-octeon/dram.c @@ -0,0 +1,27 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2020 Marvell International Ltd. + */ + +#include +#include +#include + +DECLARE_GLOBAL_DATA_PTR; + +int dram_init(void) +{ + /* + * No DDR init yet -> run in L2 cache + */ + gd->ram_size = (2 << 20); + gd->bd->bi_dram[0].size = gd->ram_size; + gd->bd->bi_dram[1].size = 0; + + return 0; +} + +ulong board_get_usable_ram_top(ulong total_size) +{ + return gd->ram_top; +} diff --git a/arch/mips/mach-octeon/include/ioremap.h b/arch/mips/mach-octeon/include/ioremap.h new file mode 100644 index 0000000000..59b75008a2 --- /dev/null +++ b/arch/mips/mach-octeon/include/ioremap.h @@ -0,0 +1,30 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +#ifndef __ASM_MACH_OCTEON_IOREMAP_H +#define __ASM_MACH_OCTEON_IOREMAP_H + +#include + +/* + * Allow physical addresses to be fixed up to help peripherals located + * outside the low 32-bit range -- generic pass-through version. + */ +static inline phys_addr_t fixup_bigphys_addr(phys_addr_t phys_addr, + phys_addr_t size) +{ + return phys_addr; +} + +static inline void __iomem *plat_ioremap(phys_addr_t offset, unsigned long size, + unsigned long flags) +{ + return (void __iomem *)(XKPHYS | offset); +} + +static inline int plat_iounmap(const volatile void __iomem *addr) +{ + return 0; +} + +#define _page_cachable_default _CACHE_CACHABLE_NONCOHERENT + +#endif /* __ASM_MACH_OCTEON_IOREMAP_H */ diff --git a/arch/mips/mach-octeon/start.S b/arch/mips/mach-octeon/start.S new file mode 100644 index 0000000000..acb967201a --- /dev/null +++ b/arch/mips/mach-octeon/start.S @@ -0,0 +1,1241 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Startup Code for OCTEON 64-bit CPU-core + * + * Copyright (c) 2003 Wolfgang Denk + * Copyright 2004, 2005, 2010 - 2015 Cavium Inc.. + */ + +#include +#include +#include +#include +#include + +#define BOOT_VECTOR_NUM_WORDS 8 + +#define OCTEON_BOOT_MOVEABLE_MAGIC_OFFSET 0x70 +#define OCTEON_BOOT_VECTOR_MOVEABLE_OFFSET 0x78 + +#define OCTEON_BOOT_MOVEABLE_MAGIC1_RAW 0xdb00110ad358eacd +#define OCTEON_BOOT_MOVEABLE_MAGIC1 OCTEON_BOOT_MOVEABLE_MAGIC1_RAW + +#define OCTEON_CIU_SOFT_RST 0x8001070000000740 + +#define OCTEON_L2C_WPAR_PP0 0x8001180080840000 +#define OCTEON_MIO_BOOT_BASE 0x8001180000000000 +#define OCTEON_MIO_BOOT_REG_CFG0_OFF 0x0000 +#define OCTEON_MIO_BOOT_LOC_CFG0_OFF 0x0080 +#define OCTEON_MIO_BOOT_LOC_ADR_OFF 0x0090 +#define OCTEON_MIO_BOOT_LOC_DAT_OFF 0x0098 +#define OCTEON_MIO_RST_BOOT 0x8001180000001600 +#define OCTEON_MIO_BOOT_REG_CFG0 0x8001180000000000 +#define OCTEON_MIO_BOOT_REG_TIM0 0x8001180000000040 +#define OCTEON_MIO_BOOT_LOC_CFG0 0x8001180000000080 +#define OCTEON_MIO_BOOT_LOC_ADR 0x8001180000000090 +#define OCTEON_MIO_BOOT_LOC_DAT 0x8001180000000098 +#define OCTEON_MIO_FUSE_DAT3 0x8001180000001418 +#define OCTEON_L2D_FUS3 0x80011800800007B8 +#define OCTEON_LMC0_DDR_PLL_CTL 0x8001180088000258 + +#define OCTEON_RST 0x8001180006000000 +#define OCTEON_RST_BOOT_OFFSET 0x1600 +#define OCTEON_RST_SOFT_RST_OFFSET 0x1680 +#define OCTEON_RST_COLD_DATAX_OFFSET(X) (0x17C0 + (X) * 8) +#define OCTEON_RST_BOOT 0x8001180006001600 +#define OCTEON_RST_SOFT_RST 0x8001180006001680 +#define OCTEON_RST_COLD_DATAX(X) (0x80011800060017C0 + (X) * 8) + +#define OCTEON_OCX_COM_NODE 0x8001180011000000 +#define OCTEON_L2C_OCI_CTL 0x8001180080800020 +#define OCTEON_L2C_TAD_CTL 0x8001180080800018 +#define OCTEON_L2C_CTL 0x8001180080800000 + +#define OCTEON_DBG_DATA 0x80011F00000001E8 +#define OCTEON_PCI_READ_CMD_E 0x80011F0000001188 +#define OCTEON_NPEI_DBG_DATA 0x80011F0000008510 +#define OCTEON_CIU_WDOG(X) (0x8001070000000500 + (X) * 8) +#define OCTEON_CIU_PP_POKE(X) (0x8001070000000580 + (X) * 8) +#define OCTEON_CIU3_WDOG(X) (0x8001010000020000 + (X) * 8) +#define OCTEON_CIU3_PP_POKE(X) (0x8001010000030000 + (X) * 8) +#define OCTEON_OCX_COM_LINKX_CTL(X) (0x8001180011000020 + (X) * 8) +#define OCTEON_SLI_CTL_STATUS 0x80011F0000028570 +#define OCTEON_GSERX_SCRATCH(X) (0x8001180090000020 + (X) * 0x1000000) + +/** PRID for CN56XX */ +#define OCTEON_PRID_CN56XX 0x04 +/** PRID for CN52XX */ +#define OCTEON_PRID_CN52XX 0x07 +/** PRID for CN63XX */ +#define OCTEON_PRID_CN63XX 0x90 +/** PRID for CN68XX */ +#define OCTEON_PRID_CN68XX 0x91 +/** PRID for CN66XX */ +#define OCTEON_PRID_CN66XX 0x92 +/** PRID for CN61XX */ +#define OCTEON_PRID_CN61XX 0x93 +/** PRID for CNF71XX */ +#define OCTEON_PRID_CNF71XX 0x94 +/** PRID for CN78XX */ +#define OCTEON_PRID_CN78XX 0x95 +/** PRID for CN70XX */ +#define OCTEON_PRID_CN70XX 0x96 +/** PRID for CN73XX */ +#define OCTEON_PRID_CN73XX 0x97 +/** PRID for CNF75XX */ +#define OCTEON_PRID_CNF75XX 0x98 + +/* func argument is used to create a mark, must be unique */ +#define GETOFFSET(reg, func) \ + .balign 8; \ + bal func ##_mark; \ + nop; \ + .dword .; \ +func ##_mark: \ + ld reg, 0(ra); \ + dsubu reg, ra, reg; + +#define JAL(func) \ + .balign 8; \ + bal func ##_mark; \ + nop; \ + .dword .; \ +func ##_mark: \ + ld t8, 0(ra); \ + dsubu t8, ra, t8; \ + dla t9, func; \ + daddu t9, t9, t8; \ + jalr t9; \ + nop; + + .set arch=octeon3 + .set noreorder + + .macro uhi_mips_exception + move k0, t9 # preserve t9 in k0 + move k1, a0 # preserve a0 in k1 + li t9, 15 # UHI exception operation + li a0, 0 # Use hard register context + sdbbp 1 # Invoke UHI operation + .endm + + .macro setup_stack_gd + li t0, -16 + PTR_LI t1, big_stack_start + and sp, t1, t0 # force 16 byte alignment + PTR_SUBU \ + sp, sp, GD_SIZE # reserve space for gd + and sp, sp, t0 # force 16 byte alignment + move k0, sp # save gd pointer +#if CONFIG_VAL(SYS_MALLOC_F_LEN) && \ + !CONFIG_IS_ENABLED(INIT_STACK_WITHOUT_MALLOC_F) + li t2, CONFIG_VAL(SYS_MALLOC_F_LEN) + PTR_SUBU \ + sp, sp, t2 # reserve space for early malloc + and sp, sp, t0 # force 16 byte alignment +#endif + move fp, sp + + /* Clear gd */ + move t0, k0 +1: + PTR_S zero, 0(t0) + PTR_ADDIU t0, PTRSIZE + blt t0, t1, 1b + nop + +#if CONFIG_VAL(SYS_MALLOC_F_LEN) && \ + !CONFIG_IS_ENABLED(INIT_STACK_WITHOUT_MALLOC_F) + PTR_S sp, GD_MALLOC_BASE(k0) # gd->malloc_base offset +#endif + .endm + +/* Saved register usage: + * s0: not used + * s1: not used + * s2: Address U-Boot loaded into in L2 cache + * s3: Start address + * s4: flags + * 1: booting from RAM + * 2: executing out of cache + * 4: booting from flash + * s5: u-boot size (data end - _start) + * s6: offset in flash. + * s7: _start physical address + * s8: + */ + +ENTRY(_start) + /* U-Boot entry point */ + b reset + + /* The above jump instruction/nop are considered part of the + * bootloader_header_t structure but are not changed when the header is + * updated. + */ + + /* Leave room for bootloader_header_t header at start of binary. This + * header is used to identify the board the bootloader is for, what + * address it is linked at, failsafe/normal, etc. It also contains a + * CRC of the entire image. + */ + +#if defined(CONFIG_ROM_EXCEPTION_VECTORS) + /* + * Exception vector entry points. When running from ROM, an exception + * cannot be handled. Halt execution and transfer control to debugger, + * if one is attached. + */ + .org 0x200 + /* TLB refill, 32 bit task */ + uhi_mips_exception + + .org 0x280 + /* XTLB refill, 64 bit task */ + uhi_mips_exception + + .org 0x300 + /* Cache error exception */ + uhi_mips_exception + + .org 0x380 + /* General exception */ + uhi_mips_exception + + .org 0x400 + /* Catch interrupt exceptions */ + uhi_mips_exception + + .org 0x480 + /* EJTAG debug exception */ +1: b 1b + nop + + .org 0x500 +#endif + +/* Reserve extra space so that when we use the boot bus local memory + * segment to remap the debug exception vector we don't overwrite + * anything useful + */ + +/* Basic exception handler (dump registers) in all ASM. When using the TLB for + * mapping u-boot C code, we can't branch to that C code for exception handling + * (TLB is disabled for some exceptions. + */ + +/* RESET/start here */ + .balign 8 +reset: + nop + synci 0(zero) + mfc0 k0, CP0_STATUS + ori k0, 0x00E0 /* enable 64 bit mode for CSR access */ + mtc0 k0, CP0_STATUS + + /* Save the address we're booting from, strip off low bits */ + bal 1f + nop +1: + move s3, ra + dins s3, zero, 0, 12 + + /* Disable boot bus moveable regions */ + PTR_LI k0, OCTEON_MIO_BOOT_LOC_CFG0 + sd zero, 0(k0) + sd zero, 8(k0) + + /* Disable the watchdog timer + * First we check if we're running on CN78XX, CN73XX or CNF75XX to see + * if we use CIU3 or CIU. + */ + mfc0 t0, CP0_PRID + ext t0, t0, 8, 8 + /* Assume CIU */ + PTR_LI t1, OCTEON_CIU_WDOG(0) + PTR_LI t2, OCTEON_CIU_PP_POKE(0) + blt t0, OCTEON_PRID_CN78XX, wd_use_ciu + nop + beq t0, OCTEON_PRID_CN70XX, wd_use_ciu + nop + /* Use CIU3 */ + PTR_LI t1, OCTEON_CIU3_WDOG(0) + PTR_LI t2, OCTEON_CIU3_PP_POKE(0) +wd_use_ciu: + sd zero, 0(t2) /* Pet the dog */ + sd zero, 0(t1) /* Disable watchdog timer */ + + /* Errata: CN76XX has a node ID of 3. change it to zero here. + * This needs to be done before we relocate to L2 as addresses change + * For 76XX pass 1.X we need to zero out the OCX_COM_NODE[ID], + * L2C_OCI_CTL[GKSEGNODE] and CP0 of Root.CvmMemCtl2[KSEGNODE]. + */ + mfc0 a4, CP0_PRID + /* Check for 78xx pass 1.x processor ID */ + andi a4, 0xffff + blt a4, (OCTEON_PRID_CN78XX << 8), 1f + nop + + /* Zero out alternate package for now */ + dins a4, zero, 6, 1 + bge a4, ((OCTEON_PRID_CN78XX << 8) | 0x08), 1f + nop + + /* 78xx or 76xx here, first check for bug #27141 */ + PTR_LI a5, OCTEON_SLI_CTL_STATUS + ld a6, 0(a5) + andi a7, a4, 0xff + andi a6, a6, 0xff + + beq a6, a7, not_bug27141 + nop + + /* core 0 proc_id rev_id field does not match SLI_CTL_STATUS rev_id */ + /* We just hit bug #27141. Need to reset the chip and try again */ + + PTR_LI a4, OCTEON_RST_SOFT_RST + ori a5, zero, 0x1 /* set the reset bit */ + +reset_78xx_27141: + sync + synci 0(zero) + cache 9, 0(zero) + sd a5, 0(a4) + wait + b reset_78xx_27141 + nop + +not_bug27141: + /* 76XX pass 1.x has the node number set to 3 */ + mfc0 a4, CP0_EBASE + ext a4, a4, 0, 10 + bne a4, 0x180, 1f /* Branch if not node 3 core 0 */ + nop + + /* Clear OCX_COM_NODE[ID] */ + PTR_LI a5, OCTEON_OCX_COM_NODE + ld a4, 0(a5) + dins a4, zero, 0, 2 + sd a4, 0(a5) + ld zero, 0(a5) + + /* Clear L2C_OCI_CTL[GKSEGNODE] */ + PTR_LI a5, OCTEON_L2C_OCI_CTL + ld a4, 0(a5) + dins a4, zero, 4, 2 + sd a4, 0(a5) + ld zero, 0(a5) + + /* Clear CP0 Root.CvmMemCtl2[KSEGNODE] */ + dmfc0 a4, CP0_CVMMEMCTL2 + dins a4, zero, 12, 2 + dmtc0 a4, CP0_CVMMEMCTL2 + + /* Put the flash address in the start of the EBASE register to + * enable our exception handler but only for core 0. + */ + mfc0 a4, CP0_EBASE + dext a4, a4, 0, 10 + bnez a4, no_flash + /* OK in delay slot */ + dext a6, a6, 0, 16 /* Get the base address in flash */ + sll a6, a6, 16 + mtc0 a6, CP0_EBASE /* Enable exceptions */ + +no_flash: + /* Zero out various registers */ + mtc0 zero, CP0_DEPC + mtc0 zero, CP0_EPC + mtc0 zero, CP0_CAUSE + mfc0 a4, CP0_PRID + ext a4, a4, 8, 8 + mtc0 zero, CP0_DESAVE + + /* The following are only available on Octeon 2 or later */ + mtc0 zero, CP0_KSCRATCH1 + mtc0 zero, CP0_KSCRATCH2 + mtc0 zero, CP0_KSCRATCH3 + mtc0 zero, CP0_USERLOCAL + + /* Turn off ROMEN bit to disable ROM */ + PTR_LI a1, OCTEON_MIO_RST_BOOT + /* For OCTEON 3 we use RST_BOOT instead of MIO_RST_BOOT. + * The difference is bits 24-26 are 6 instead of 0 for the address. + */ + /* For Octeon 2 and CN70XX we can ignore the watchdog */ + blt a4, OCTEON_PRID_CN78XX, watchdog_ok + nop + + PTR_LI a1, OCTEON_RST_BOOT + + beq a4, OCTEON_PRID_CN70XX, watchdog_ok + nop + + ld a2, 0(a1) + /* There is a bug where some registers don't get properly reset when + * the watchdog timer causes a reset. In this case we need to force + * a reset. + */ + bbit0 a2, 11, watchdog_ok /* Skip if watchdog not hit */ + dins a2, zero, 2, 18 /* Don't clear LBOOT, LBOOT_EXT or LBOOT_OCI */ + /* Clear bit indicating reset due to watchdog */ + ori a2, 1 << 11 + sd a2, 0(a1) + + /* Disable watchdog */ + PTR_LI a1, OCTEON_CIU3_PP_POKE(0) + sd zero, 0(a1) + PTR_LI a1, OCTEON_CIU3_WDOG(0) + sd zero, 0(a1) + + /* Record this in the GSER0_SCRATCH register in bit 11 */ + PTR_LI a1, OCTEON_GSERX_SCRATCH(0) + ld a2, 0(a1) + ori a2, 1 << 11 + sd a2, 0(a1) + + PTR_LI a1, OCTEON_RST_SOFT_RST + li a2, 1 + sd a2, 0(a1) + wait + + /* We should never get here */ + +watchdog_ok: + ld a2, 0(a1) + /* Don't clear LBOOT/LBOOT_EXT or LBOOT_OCI */ + dins a2, zero, 2, 18 + dins a2, zero, 60, 1 /* Clear ROMEN bit */ + sd a2, 0(a1) + + /* Start of Octeon setup */ + + /* Check what core we are - if core 0, branch to init tlb + * loop in flash. Otherwise, look up address of init tlb + * loop that was saved in the boot vector block. + */ + mfc0 a0, CP0_EBASE + andi a0, EBASE_CPUNUM /* get core */ + beqz a0, InitTLBStart_local + nop + + break + /* We should never get here - non-zero cores now go directly to + * tlb init from the boot stub in movable region. + */ + + .globl InitTLBStart +InitTLBStart: +InitTLBStart_local: + /* If we don't have working memory yet configure a bunch of + * scratch memory, and set the stack pointer to the top + * of it. This allows us to go to C code without having + * memory set up + * + * Warning: do not change SCRATCH_STACK_LINES as this can impact the + * transition from start.S to crti.asm. crti requires 590 bytes of + * stack space. + */ + cache 1,0(zero) /* Clear Dcache so cvmseg works right */ +#if CONFIG_OCTEON_BIG_STACK_SIZE + rdhwr v0, $0 + bnez v0, 1f + nop + PTR_LA sp, big_stack_start - 16 + b stack_clear_done + nop +1: +#endif +#define SCRATCH_STACK_LINES 0x36 /* MAX is 0x36 */ + dmfc0 v0, CP0_CVMMEMCTL + dins v0, zero, 0, 9 + /* setup SCRATCH_STACK_LINES scratch lines of scratch */ + ori v0, 0x100 | SCRATCH_STACK_LINES + dmtc0 v0, CP0_CVMMEMCTL + /* set stack to top of scratch memory */ + li sp, 0xffffffffffff8000 + (SCRATCH_STACK_LINES * 128) + /* Clear scratch for CN63XX pass 2.0 errata Core-15169*/ + li t0, 0xffffffffffff8000 +clear_scratch: + sd zero, 0(t0) + addiu t0, 8 + bne t0, sp, clear_scratch + nop + + /* This code run on all cores - core 0 from flash, + * the rest from DRAM. When booting from PCI, non-zero cores + * come directly here from the boot vector - no earlier code in this + * file is executed. + */ + + /* Some generic initialization is done here as well, as we need this + * done on all cores even when booting from PCI + */ +stack_clear_done: + /* Clear watch registers. */ + mtc0 zero, CP0_WATCHLO + mtc0 zero, CP0_WATCHHI + + /* STATUS register */ + mfc0 k0, CP0_STATUS + li k1, ~ST0_IE + and k0, k1 + mtc0 k0, CP0_STATUS + + /* CAUSE register */ + mtc0 zero, CP0_CAUSE + + /* Init Timer */ + dmtc0 zero, CP0_COUNT + dmtc0 zero, CP0_COMPARE + + + mfc0 a5, CP0_STATUS + li v0, 0xE0 /* enable 64 bit mode for CSR access */ + or v0, v0, a5 + mtc0 v0, CP0_STATUS + + + dli v0, 1 << 29 /* Enable large physical address support in TLB */ + mtc0 v0, CP0_PAGEGRAIN + +InitTLB: + dmtc0 zero, CP0_ENTRYLO0 + dmtc0 zero, CP0_ENTRYLO1 + mtc0 zero, CP0_PAGEMASK + dmtc0 zero, CP0_CONTEXT + /* Use an offset into kseg0 so we won't conflict with Mips1 legacy + * TLB clearing + */ + PTR_LI v0, 0xFFFFFFFF90000000 + mfc0 a0, CP0_CONFIG1 + srl a0, a0, 25 + /* Check if config4 reg present */ + mfc0 a1, CP0_CONFIG3 + bbit0 a1, 31, 2f + and a0, a0, 0x3F /* a0 now has the max mmu entry index */ + mfc0 a1, CP0_CONFIG4 + bbit0 a1, 14, 2f /* check config4[MMUExtDef] */ + nop + /* append config4[MMUSizeExt] to most significant bit of + * config1[MMUSize-1] + */ + ins a0, a1, 6, 8 + and a0, a0, 0x3fff /* a0 now includes max entries for cn6xxx */ +2: + dmtc0 zero, CP0_XCONTEXT + mtc0 zero, CP0_WIRED + +InitTLBloop: + dmtc0 v0, CP0_ENTRYHI + tlbp + mfc0 v1, CP0_INDEX + daddiu v0, v0, 1<<13 + bgez v1, InitTLBloop + + mtc0 a0, CP0_INDEX + tlbwi + bnez a0, InitTLBloop + daddiu a0, -1 + + mthi zero + mtlo zero + + /* Set up status register */ + mfc0 v0, CP0_STATUS + /* Enable COP0 and COP2 access */ + li a4, (1 << 28) | (1 << 30) + or v0, a4 + + /* Must leave BEV set here, as DRAM is not configured for core 0. + * Also, BEV must be 1 later on when the exception base address is set. + */ + + /* Mask all interrupts */ + ins v0, zero, 0, 16 + /* Clear NMI (used to start cores other than core 0) */ + ori v0, 0xE4 /* enable 64 bit, disable interrupts */ + mtc0 v0, CP0_STATUS + + dli v0,0xE000000F /* enable all readhw locations */ + mtc0 v0, CP0_HWRENA + + dmfc0 v0, CP0_CVMCTL + ori v0, 1<<14 /* enable fixup of unaligned mem access */ + dmtc0 v0, CP0_CVMCTL + + /* Setup scratch memory. This is also done in + * cvmx_user_app_init, and this code will be removed + * from the bootloader in the near future. + */ + + /* Set L2C_LAD_CTL[MAXLFB] = 0 on CN73XX */ + mfc0 a4, CP0_PRID + ext a4, a4, 8, 8 + blt a4, OCTEON_PRID_CN73XX, 72f + nop + PTR_LI v0, OCTEON_L2C_TAD_CTL + ld t1, 0(v0) + dins t1, zero, 0, 4 + sd t1, 0(v0) + ld zero, 0(v0) + +72: + + /* clear these to avoid immediate interrupt in noperf mode */ + dmtc0 zero, CP0_COMPARE /* clear timer interrupt */ + dmtc0 zero, CP0_COUNT /* clear timer interrupt */ + dmtc0 zero, CP0_PERF_CNT0 /* clear perfCnt0 */ + dmtc0 zero, CP0_PERF_CNT1 /* clear perfCnt1 */ + dmtc0 zero, CP0_PERF_CNT2 + dmtc0 zero, CP0_PERF_CNT3 + + /* If we're running on a node other than 0 then we need to set KSEGNODE + * to 0. The nice thing with this code is that it also autodetects if + * we're running on a processor that supports CVMMEMCTL2 or not since + * only processors that have this will have a non-zero node ID. Because + * of this there's no need to check if we're running on a 78XX. + */ + mfc0 t1, CP0_EBASE + dext t1, t1, 7, 3 /* Extract node number */ + beqz t1, is_node0 /* If non-zero then we're not node 0 */ + nop + dmfc0 t1, CP0_CVMMEMCTL2 + dins t1, zero, 12, 4 + dmtc0 t1, CP0_CVMMEMCTL2 +is_node0: + + /* Set up TLB mappings for u-boot code in flash. */ + + /* Use a bal to get the current PC into ra. Since this bal is to + * the address immediately following the delay slot, the ra is + * the address of the label. We then use this to get the actual + * address that we are executing from. + */ + bal __dummy + nop + +__dummy: + /* Get the actual address that we are running at */ + PTR_LA a6, _start /* Linked address of _start */ + PTR_LA a7, __dummy + dsubu t0, a7, a6 /* offset of __dummy label from _start*/ + dsubu a7, ra, t0 /* a7 now has actual address of _start*/ + + /* Save actual _start address in s7. This is where we + * are executing from, as opposed to where the code is + * linked. + */ + move s7, a7 + move s4, zero + + /* s7 has actual address of _start. If this is + * on the boot bus, it will be between 0xBFC000000 and 0xBFFFFFFF. + * If it is on the boot bus, use 0xBFC00000 as the physical address + * for the TLB mapping, as we will be adjusting the boot bus + * to make this adjustment. + * If we are running from DRAM (remote-boot), then we want to use the + * real address in DRAM. + */ + + /* Check to see if we are running from flash - we expect that to + * be 0xffffffffb0000000-0xffffffffbfffffff + * (0x10000000-0x1fffffff, unmapped/uncached) + */ + dli t2, 0xffffffffb0000000 + dsubu t2, s7 + slt s4, s7, t2 + bltz t2, uboot_in_flash + nop + + /* If we're not core 0 then we don't care about cache */ + mfc0 t2, CP0_EBASE + andi t2, EBASE_CPUNUM + bnez t2, uboot_in_ram + nop + + /* Find out if we're OCTEON I or OCTEON + which don't support running + * out of cache. + */ + mfc0 t2, CP0_PRID + ext t2, t2, 8, 8 + li s4, 1 + blt t2, 0x90, uboot_in_ram + nop + + /* U-Boot can be executing either in RAM or L2 cache. Now we need to + * check if DRAM is initialized. The way we do that is to look at + * the reset bit of the LMC0_DDR_PLL_CTL register (bit 7) + */ + PTR_LI t2, OCTEON_LMC0_DDR_PLL_CTL + ld t2, 0(t2) + bbit1 t2, 7, uboot_in_ram + nop + + /* We must be executing out of cache */ + b uboot_in_ram + li s4, 2 + +uboot_in_flash: + /* Set s4 to 4 to indicate we're running in FLASH */ + li s4, 4 + +#if defined(CONFIG_OCTEON_DISABLE_L2_CACHE_INDEX_ALIASING) + /* By default, L2C index aliasing is enabled. In some cases it may + * need to be disabled. The L2C index aliasing can only be disabled + * if U-Boot is running out of L2 cache and the L2 cache has not been + * used to store anything. + */ + PTR_LI t1, OCTEON_L2C_CTL + ld t2, 0(t1) + ori t2, 1 + sd t2, 0(t1) +#endif + + /* Use BFC00000 as physical address for TLB mappings when booting + * from flash, as we will adjust the boot bus mappings to make this + * mapping correct. + */ + dli a7, 0xFFFFFFFFBFC00000 + dsubu s6, s7, a7 /* Save flash offset in s6 */ + +#if defined(CONFIG_OCTEON_COPY_FROM_FLASH_TO_L2) + /* For OCTEON II we check to see if the L2 cache is big enough to hold + * U-Boot. If it is big enough then we copy ourself from flash to the + * L2 cache in order to speed up execution. + */ + + /* Check for OCTEON 2 */ + mfc0 t1, CP0_PRID + ext t1, t1, 8, 8 + /* Get number of L2 cache sets */ + beq t1, OCTEON_PRID_CNF71XX, got_l2_sets /* CNF71XX */ + li t2, 1 << 9 + beq t1, OCTEON_PRID_CN78XX, got_l2_sets /* CN78XX */ + li t2, 1 << 13 + beq t1, OCTEON_PRID_CN70XX, got_l2_sets /* CN70XX */ + li t2, 1 << 10 + beq t1, OCTEON_PRID_CN73XX, got_l2_sets /* CN73XX */ + li t2, 1 << 11 + beq t1, OCTEON_PRID_CNF75XX, got_l2_sets /* CNF75XX */ + li t2, 1 << 11 + b l2_cache_too_small /* Unknown OCTEON model */ + nop + +got_l2_sets: + /* Get number of associations */ + PTR_LI t0, OCTEON_MIO_FUSE_DAT3 + ld t0, 0(t0) + dext t0, t0, 32, 3 + + beq t1, OCTEON_PRID_CN70XX, process_70xx_l2sets + nop + /* 0 = 16-way, 1 = 12-way, 2 = 8-way, 3 = 4-way, 4-7 reserved */ + beqz t0, got_l2_ways + li t3, 16 + beq t0, 1, got_l2_ways + li t3, 12 + beq t0, 2, got_l2_ways + li t3, 8 + beq t0, 3, got_l2_ways + li t3, 4 + b l2_cache_too_small + nop + +process_70xx_l2sets: + /* For 70XX, the number of ways is defined as: + * 0 - full cache (4-way) 512K + * 1 - 3/4 ways (3-way) 384K + * 2 - 1/2 ways (2-way) 256K + * 3 - 1/4 ways (1-way) 128K + * 4-7 illegal (aliased to 0-3) + */ + andi t0, 3 + beqz t0, got_l2_ways + li t3, 4 + beq t0, 1, got_l2_ways + li t3, 3 + beq t0, 2, got_l2_ways + li t3, 2 + li t3, 1 + +got_l2_ways: + dmul a1, t2, t3 /* Calculate cache size */ + dsll a1, 7 /* Ways * Sets * cache line sz (128) */ + daddiu a1, a1, -128 /* Adjust cache size for copy code */ + + /* Calculate size of U-Boot image */ + /* + * "uboot_end - _start" is not correct, as the image also + * includes the DTB appended to the end (OF_EMBED is deprecated). + * Lets use a defined max for now here. + */ + PTR_LI s5, CONFIG_BOARD_SIZE_LIMIT + + daddu t2, s5, s7 /* t2 = end address */ + daddiu t2, t2, 127 + ins t2, zero, 0, 7 /* Round up to cache line for memcpy */ + + slt t1, a1, s5 /* See if we're bigger than the L2 cache */ + bnez t1, l2_cache_too_small + nop + /* Address we plan to load at in the L2 cache */ + PTR_LI t9, CONFIG_OCTEON_L2_UBOOT_ADDR +# ifdef CONFIG_OCTEON_L2_MEMCPY_IN_CACHE + /* Enable all ways for PP0. Authentik ROM may have disabled these */ + PTR_LI a1, OCTEON_L2C_WPAR_PP0 + sd zero, 0(a1) + + /* Address to place our memcpy code */ + PTR_LI a0, CONFIG_OCTEON_L2_MEMCPY_ADDR + /* The following code writes a simple memcpy routine into the cache + * to copy ourself from flash into the L2 cache. This makes the + * memcpy routine a lot faster since each instruction can potentially + * require four read cycles to flash over the boot bus. + */ + /* Zero cache line in the L2 cache */ + zcb (a0) + synci 0(zero) + dli a1, 0xdd840000dd850008 /* ld a0, 0(t0); ld a1, 8(t0) */ + sd a1, 0(a0) + dli a1, 0xdd860010dd870018 /* ld a2, 16(t0); ld a3, 24(t0) */ + sd a1, 8(a0) + dli a1, 0xfda40000fda50008 /* sd a0, 0(t1); sd a1, 8(t1) */ + sd a1, 16(a0) + dli a1, 0xfda60010fda70018 /* sd a2, 16(t1); sd a3, 24(t1) */ + sd a1, 24(a0) + dli a1, 0x258c0020158efff6 /* addiu t0, 32; bne t0, t2, -40 */ + sd a1, 32(a0) + dli a1, 0x25ad002003e00008 /* addiu t1, 32; jr ra */ + sd a1, 40(a0) + sd zero, 48(a0) /* nop; nop */ + + /* Synchronize the caches */ + sync + synci 0(zero) + + move t0, s7 + move t1, t9 + + /* Do the memcpy operation in L2 cache to copy ourself from flash + * to the L2 cache. + */ + jalr a0 + nop + +# else + /* Copy ourself to the L2 cache from flash, 32 bytes at a time */ + /* This code is now written to the L2 cache using the code above */ +1: + ld a0, 0(t0) + ld a1, 8(t0) + ld a2, 16(t0) + ld a3, 24(t0) + sd a0, 0(t1) + sd a1, 8(t1) + sd a2, 16(t1) + sd a3, 24(t1) + addiu t0, 32 + bne t0, t2, 1b + addiu t1, 32 +# endif /* CONFIG_OCTEON_L2_MEMCPY_IN_CACHE */ + + /* Adjust the start address of U-Boot and the global pointer */ + subu t0, s7, t9 /* t0 = address difference */ + move s7, t9 /* Update physical address */ + move s2, t9 + sync + synci 0(zero) + + /* Now we branch to the L2 cache. We first get our PC then adjust it + */ + bal 3f + nop +3: + /* Don't add any instructions here! */ + subu t9, ra, t0 + /* Give ourself 16 bytes */ + addiu t9, 0x10 + + jal t9 /* Branch to address in L2 cache */ + + nop + nop + /* Add instructions after here */ + + move a7, s7 + + b uboot_in_ram + ori s4, 2 /* Running out of L2 cache */ + +l2_cache_too_small: /* We go here if we can't copy ourself to L2 */ +#endif /* CONFIG_OCTEON_COPY_FROM_FLASH_TO_L2 */ + + /* This code is only executed if booting from flash. */ + /* For flash boot (_not_ RAM boot), we do a workaround for + * an LLM errata on CN38XX and CN58XX parts. + */ + +uboot_in_ram: + /* U-boot address is now in reg a7, and is 4 MByte aligned. + * (boot bus addressing has been adjusted to make this happen for flash, + * and for DRAM this alignment must be provided by the remote boot + * utility. + */ + /* See if we're in KSEG0 range, if so set EBASE register to handle + * exceptions. + */ + dli a1, 0x20000000 + bge a7, a1, 1f + nop + /* Convert our physical address to KSEG0 */ + PTR_LI a1, 0xffffffff80000000 + or a1, a1, a7 + mtc0 a1, CP0_EBASE +1: + /* U-boot now starts at 0xBFC00000. Use a single 4 MByte TLB mapping + * to map u-boot. + */ + move a0, a6 /* Virtual addr in a0 */ + dins a0, zero, 0, 16 /* Zero out offset bits */ + move a1, a7 /* Physical addr in a1 */ + + /* Now we need to remove the MIPS address space bits. For this we + * need to determine if it is a 32 bit compatibility address or not. + */ + + /* 'lowest' address in compatibility space */ + PTR_LI t0, 0xffffffff80000000 + dsubu t0, t0, a1 + bltz t0, compat_space + nop + + /* We have a xkphys address, so strip off top bit */ + b addr_fixup_done + dins a1, zero, 63, 1 + +compat_space: + PTR_LI a2, 0x1fffffff + and a1, a1, a2 /* Mask phy addr to remove address space bits */ + +addr_fixup_done: + /* Currenty the u-boot image size is limited to 4 MBytes. In order to + * support larger images the flash mapping will need to be changed to + * be able to access more than that before C code is run. Until that + * is done, we just use a 4 MByte mapping for the secondary cores as + * well. + */ + /* page size (only support 4 Meg binary size for now for core 0) + * This limitation is due to the fact that the boot vector is + * 0xBFC00000 which only makes 4MB available. Later more flash + * address space will be available after U-Boot has been copied to + * RAM. For now assume that it is in flash. + */ + li a2, 2*1024*1024 + + mfc0 a4, CP0_EBASE + andi a4, EBASE_CPUNUM /* get core */ + beqz a4, core_0_tlb + nop + + /* Now determine how big a mapping to use for secondary cores, + * which need to map all of u-boot + heap in DRAM + */ + /* Here we look at the alignment of the the physical address, + * and use the largest page size possible. In some cases + * this can result in an oversize mapping, but for secondary cores + * this mapping is very short lived. + */ + + /* Physical address in a1 */ + li a2, 1 +1: + sll a2, 1 + and a5, a1, a2 + beqz a5, 1b + nop + + /* a2 now contains largest page size we can use */ +core_0_tlb: + JAL(single_tlb_setup) + + /* Check if we're running from cache */ + bbit1 s4, 1, uboot_in_cache + nop + + /* If we are already running from ram, we don't need to muck + * with boot bus mappings. + */ + PTR_LI t2, 0xffffffffb0000000 + dsubu t2, s7 + /* See if our starting address is lower than the boot bus */ + bgez t2, uboot_in_ram2 /* If yes, booting from RAM */ + nop + +uboot_in_cache: +#if CONFIG_OCTEON_BIG_STACK_SIZE + /* The large stack is only for core 0. For all other cores we need to + * use the L1 cache otherwise the other cores will stomp on top of each + * other unless even more space is reserved for the stack space for + * each core. With potentially 96 cores this gets excessive. + */ + mfc0 v0, CP0_EBASE + andi a0, EBASE_CPUNUM + bnez a0, no_big_stack + nop + PTR_LA sp, big_stack_start + daddiu sp, -16 + +no_big_stack: +#endif + /* We now have the TLB set up, so we need to remap the boot bus. + * This is tricky, as we are running from flash, and will be changing + * the addressing of the flash. + */ + /* Enable movable boot bus region 0, at address 0x10000000 */ + PTR_LI a4, OCTEON_MIO_BOOT_BASE + dli a5, 0x81000000 /* EN + base address 0x11000000 */ + sd a5, OCTEON_MIO_BOOT_LOC_CFG0_OFF(a4) + + /* Copy code to that remaps the boot bus to movable region */ + sd zero, OCTEON_MIO_BOOT_LOC_DAT_OFF(a4) + + PTR_LA a6, change_boot_mappings + GETOFFSET(a5, change_boot_mappings); + daddu a5, a5, a6 + + /* The code is 16 bytes (2 DWORDS) */ + ld a7, 0(a5) + sd a7, OCTEON_MIO_BOOT_LOC_DAT_OFF(a4) + ld a7, 8(a5) + sd a7, OCTEON_MIO_BOOT_LOC_DAT_OFF(a4) + + /* Read from an RML register to ensure that the previous writes have + * completed before we branch to the movable region. + */ + ld zero, OCTEON_MIO_BOOT_LOC_CFG0_OFF(a4) + + /* Compute value for boot bus configuration register */ + /* Read region 0 config so we can _modify_ the base address field */ + PTR_LI a4, OCTEON_MIO_BOOT_REG_CFG0 /* region 0 config */ + ld a0, 0(a4) + dli a4, 0xf0000000 /* Mask off bits we want to save */ + and a4, a4, a0 + dli a0, 0x0fff0000 /* Force size to max */ + or a4, a4, a0 + + move a5, s6 + /* Convert to 64k blocks, as used by boot bus config */ + srl a5, 16 + li a6, 0x1fc0 /* 'normal' boot bus base config value */ + subu a6, a6, a5 /* Subtract offset */ + /* combine into register value to pass to boot bus routine */ + or a0, a4, a6 + + /* Branch there */ + PTR_LA a1, __mapped_continue_label + PTR_LI a2, OCTEON_MIO_BOOT_REG_CFG0 + /* If region 0 is not enabled we can skip it */ + ld a4, 0(a2) + bbit0 a4, 31, __mapped_continue_label + nop + li a4, 0x10000000 + j a4 + synci 0(zero) + + /* We never get here, as we go directly to __mapped_continue_label */ + break + + +uboot_in_ram2: + + /* Now jump to address in TLB mapped memory to continue execution */ + PTR_LA a4, __mapped_continue_label + synci 0(a4) + j a4 + nop + +__mapped_continue_label: + /* Check if we are core 0, if we are not then we need + * to vector to code in DRAM to do application setup, and + * skip the rest of the bootloader. Only core 0 runs the bootloader + * and sets up the tables that the other cores will use for + * configuration. + */ + mfc0 a0, CP0_EBASE + andi a0, EBASE_CPUNUM /* get core */ + /* if (__all_cores_are_equal==0 && core==0), + * then jump to execute BL on core 0; else 'go to next line' + * (core_0_cont1 is executed ONLY when k0=a0=0(core0_ID)) + */ + lw t0, __all_cores_are_equal + beq a0, t0, core_0_cont1 + nop + + /* other cores look up addr from dram */ + /* DRAM controller already set up by first core */ + li a1, (BOOT_VECTOR_NUM_WORDS * 4) + mul a0, a0, a1 + + /* Now find out the boot vector base address from the moveable boot + * bus region. + */ + + /* Get the address of the boot bus moveable region */ + PTR_LI t8, OCTEON_MIO_BOOT_BASE + ld t9, OCTEON_MIO_BOOT_LOC_CFG0_OFF(t8) + /* Make sure it's enabled */ + bbit0 t9, 31, invalid_boot_vector + dext t9, t9, 3, 24 + dsll t9, t9, 7 + /* Make address XKPHYS */ + li t0, 1 + dins t9, t0, 63, 1 + + ld t0, OCTEON_BOOT_MOVEABLE_MAGIC_OFFSET(t9) + dli t1, OCTEON_BOOT_MOVEABLE_MAGIC1 + bne t0, t1, invalid_boot_vector + nop + + /* Load base address of boot vector table */ + ld t0, OCTEON_BOOT_VECTOR_MOVEABLE_OFFSET(t9) + /* Add offset for core */ + daddu a1, t0, a0 + + mfc0 v0, CP0_STATUS + move v1, v0 + ins v1, zero, 19, 1 /* Clear NMI bit */ + mtc0 v1, CP0_STATUS + + /* Get app start function address */ + lw t9, 8(a1) + beqz t9, invalid_boot_vector + nop + + j t9 + lw k0, 12(a1) /* Load global data (deprecated) */ + +invalid_boot_vector: + wait + b invalid_boot_vector + nop + +__all_cores_are_equal: + /* The following .word tell if 'all_cores_are_equal' or core0 is special + * By default (for the first execution) the core0 should be special, + * in order to behave like the old(existing not-modified) bootloader + * and run the bootloader on core 0 to follow the existing design. + * However after that we make 'all_cores_equal' which allows to run SE + * applications on core0 like on any other core. NOTE that value written + * to '__all_cores_are_equal' should not match any core ID. + */ + .word 0 + +core_0_cont1: + li t0, 0xffffffff + sw t0, __all_cores_are_equal + /* From here on, only core 0 runs, other cores have branched + * away. + */ +#ifdef CONFIG_MIPS_INIT_STACK_IN_SRAM + /* Set up initial stack and global data */ + setup_stack_gd +# ifdef CONFIG_DEBUG_UART + PTR_LA t9, debug_uart_init + jalr t9 + nop +# endif +#endif + move a0, zero # a0 <-- boot_flags = 0 + PTR_LA t9, board_init_f + + jr t9 + move ra, zero + END(_start) + + .balign 8 + .globl single_tlb_setup + .ent single_tlb_setup + /* Sets up a single TLB entry. Virtual/physical addresses + * must be properly aligned. + * a0 Virtual address + * a1 Physical address + * a2 page (_not_ mapping) size + */ +single_tlb_setup: + /* Determine the number of TLB entries available, and + * use the top one. + */ + mfc0 a3, CP0_CONFIG1 + dext a3, a3, 25, 6 /* a3 now has the max mmu entry index */ + mfc0 a5, CP0_CONFIG3 /* Check if config4 reg present */ + bbit0 a5, 31, single_tlb_setup_cont + nop + mfc0 a5, CP0_CONFIG4 + bbit0 a5, 14, single_tlb_setup_cont /* check config4[MMUExtDef] */ + nop + /* append config4[MMUSizeExt] to most significant bit of + * config1[MMUSize-1] + */ + dins a3, a5, 6, 8 + and a3, a3, 0x3fff /* a3 now includes max entries for cn6xxx */ + +single_tlb_setup_cont: + + /* Format physical address for entry low */ + nop + dsrl a1, a1, 12 + dsll a1, a1, 6 + ori a1, a1, 0x7 /* set DVG bits */ + + move a4, a2 + daddu a5, a4, a4 /* mapping size */ + dsll a6, a4, 1 + daddiu a6, a6, -1 /* pagemask */ + dsrl a4, a4, 6 /* adjust for adding with entrylo */ + + /* Now set up mapping */ + mtc0 a6, CP0_PAGEMASK + mtc0 a3, CP0_INDEX + + dmtc0 a1, CP0_ENTRYLO0 + daddu a1, a1, a4 + + dmtc0 a1, CP0_ENTRYLO1 + daddu a1, a1, a4 + + dmtc0 a0, CP0_ENTRYHI + daddu a0, a0, a5 + + ehb + tlbwi + jr ra + nop + .end single_tlb_setup + + +/** + * This code is moved to a movable boot bus region, + * and it is responsible for changing the flash mappings and + * jumping to run from the TLB mapped address. + * + * @param a0 New address for boot bus region 0 + * @param a1 Address to branch to afterwards + * @param a2 Address of MIO_BOOT_REG_CFG0 + */ + .balign 8 +change_boot_mappings: + sd a0, 0(a2) + sync + j a1 /* Jump to new TLB mapped location */ + synci 0(zero) + +/* If we need a large stack, allocate it here. */ +#if CONFIG_OCTEON_BIG_STACK_SIZE + /* Allocate the stack here so it's in L2 cache or DRAM */ + .balign 16 +big_stack_end: + .skip CONFIG_OCTEON_BIG_STACK_SIZE, 0 +big_stack_start: + .dword 0 +#endif From patchwork Sat May 2 08:59:36 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Stefan Roese X-Patchwork-Id: 244766 List-Id: U-Boot discussion From: sr at denx.de (Stefan Roese) Date: Sat, 2 May 2020 10:59:36 +0200 Subject: [PATCH v1 02/10] mips: cache: Allow using CONFIG_MIPS_L2_CACHE without CONFIG_MIPS_CM In-Reply-To: <20200502085944.13444-1-sr@denx.de> References: <20200502085944.13444-1-sr@denx.de> Message-ID: <20200502085944.13444-3-sr@denx.de> This patch enables the usage of CONFIG_MIPS_L2_CACHE without CONFIG_MIPS_CM, which is what is needed for the newly added Octeon platform. Signed-off-by: Stefan Roese --- arch/mips/lib/cache.c | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-) diff --git a/arch/mips/lib/cache.c b/arch/mips/lib/cache.c index 1a8c87d094..9e20b39608 100644 --- a/arch/mips/lib/cache.c +++ b/arch/mips/lib/cache.c @@ -7,7 +7,7 @@ #include #include #include -#ifdef CONFIG_MIPS_L2_CACHE +#ifdef CONFIG_MIPS_CM #include #endif #include @@ -16,6 +16,17 @@ DECLARE_GLOBAL_DATA_PTR; +#if defined(CONFIG_MIPS_L2_CACHE) && !defined(CONFIG_MIPS_CM) +/* + * Dummy implementation to avoid compile warning on platforms with L2 + * cache but without CM + */ +static unsigned long mips_cm_l2_line_size(void) +{ + return 0; +} +#endif + static void probe_l2(void) { #ifdef CONFIG_MIPS_L2_CACHE From patchwork Sat May 2 08:59:37 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Stefan Roese X-Patchwork-Id: 244767 List-Id: U-Boot discussion From: sr at denx.de (Stefan Roese) Date: Sat, 2 May 2020 10:59:37 +0200 Subject: [PATCH v1 03/10] mips: cache: Don't use cache operations with CONFIG_MIPS_CACHE_COHERENT In-Reply-To: <20200502085944.13444-1-sr@denx.de> References: <20200502085944.13444-1-sr@denx.de> Message-ID: <20200502085944.13444-4-sr@denx.de> The Octeon platform is cache coherent and cache flushes and invalidates are not needed. This patch makes use of the newly introduced Kconfig option CONFIG_MIPS_CACHE_COHERENT to effectively disable all the cache operations. Signed-off-by: Stefan Roese --- arch/mips/lib/cache.c | 38 ++++++++++++++++++++++++++++++-------- 1 file changed, 30 insertions(+), 8 deletions(-) diff --git a/arch/mips/lib/cache.c b/arch/mips/lib/cache.c index 9e20b39608..e27826cbb1 100644 --- a/arch/mips/lib/cache.c +++ b/arch/mips/lib/cache.c @@ -118,6 +118,7 @@ static inline unsigned long scache_line_size(void) } \ } while (0) +#if !defined(CONFIG_MIPS_CACHE_COHERENT) void flush_cache(ulong start_addr, ulong size) { unsigned long ilsize = icache_line_size(); @@ -188,6 +189,35 @@ void invalidate_dcache_range(ulong start_addr, ulong stop) sync(); } +void dcache_disable(void) +{ + /* change CCA to uncached */ + change_c0_config(CONF_CM_CMASK, CONF_CM_UNCACHED); + + /* ensure the pipeline doesn't contain now-invalid instructions */ + instruction_hazard_barrier(); +} + +#else /* CONFIG_MIPS_CACHE_COHERENT */ + +void flush_cache(ulong start_addr, ulong size) +{ +} + +void __weak flush_dcache_range(ulong start_addr, ulong stop) +{ +} + +void invalidate_dcache_range(ulong start_addr, ulong stop) +{ +} + +void dcache_disable(void) +{ +} + +#endif /* CONFIG_MIPS_CACHE_COHERENT */ + int dcache_status(void) { unsigned int cca = read_c0_config() & CONF_CM_CMASK; @@ -199,11 +229,3 @@ void dcache_enable(void) puts("Not supported!\n"); } -void dcache_disable(void) -{ - /* change CCA to uncached */ - change_c0_config(CONF_CM_CMASK, CONF_CM_UNCACHED); - - /* ensure the pipeline doesn't contain now-invalid instructions */ - instruction_hazard_barrier(); -} From patchwork Sat May 2 08:59:38 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Stefan Roese X-Patchwork-Id: 244769 List-Id: U-Boot discussion From: sr at denx.de (Stefan Roese) Date: Sat, 2 May 2020 10:59:38 +0200 Subject: [PATCH v1 04/10] mips: traps: Set WG bit in EBase register on Octeon In-Reply-To: <20200502085944.13444-1-sr@denx.de> References: <20200502085944.13444-1-sr@denx.de> Message-ID: <20200502085944.13444-5-sr@denx.de> WG (bit 11) needs to be set on Octeon to enable writing bits 63:30 of the exception base register. Signed-off-by: Stefan Roese --- arch/mips/lib/traps.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/mips/lib/traps.c b/arch/mips/lib/traps.c index 8fff7541e3..ccbce97161 100644 --- a/arch/mips/lib/traps.c +++ b/arch/mips/lib/traps.c @@ -106,6 +106,10 @@ void trap_init(ulong reloc_addr) saved_ebase = read_c0_ebase() & 0xfffff000; + /* Set WG bit on Octeon to enable writing to bits 63:30 */ + if (IS_ENABLED(CONFIG_ARCH_OCTEON)) + ebase |= BIT(11); + write_c0_ebase(ebase); clear_c0_status(ST0_BEV); execution_hazard_barrier(); From patchwork Sat May 2 08:59:39 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Stefan Roese X-Patchwork-Id: 244768 List-Id: U-Boot discussion From: sr at denx.de (Stefan Roese) Date: Sat, 2 May 2020 10:59:39 +0200 Subject: [PATCH v1 05/10] mips: Rename CONFIG_CPU_CAVIUM_OCTEON to CONFIG_CPU_MIPS64_OCTEON In-Reply-To: <20200502085944.13444-1-sr@denx.de> References: <20200502085944.13444-1-sr@denx.de> Message-ID: <20200502085944.13444-6-sr@denx.de> With the introduction of the MIPS Octeon support, lets use the newly added Kconfig symbol CONFIG_CPU_MIPS64_OCTEON instead of the old Linux CONFIG_CPU_CAVIUM_OCTEON one (which was never set). Remove these references completely with this patch. Signed-off-by: Stefan Roese --- arch/mips/include/asm/io.h | 4 ++-- arch/mips/include/asm/ptrace.h | 2 +- scripts/config_whitelist.txt | 1 - 3 files changed, 3 insertions(+), 4 deletions(-) diff --git a/arch/mips/include/asm/io.h b/arch/mips/include/asm/io.h index 7c40e415c7..072d1718c9 100644 --- a/arch/mips/include/asm/io.h +++ b/arch/mips/include/asm/io.h @@ -223,7 +223,7 @@ static inline void iounmap(const volatile void __iomem *addr) plat_iounmap(addr); } -#ifdef CONFIG_CPU_CAVIUM_OCTEON +#ifdef CONFIG_CPU_MIPS64_OCTEON #define war_octeon_io_reorder_wmb() wmb() #else #define war_octeon_io_reorder_wmb() do { } while (0) @@ -452,7 +452,7 @@ BUILDSTRING(q, u64) #endif -#ifdef CONFIG_CPU_CAVIUM_OCTEON +#ifdef CONFIG_CPU_MIPS64_OCTEON #define mmiowb() wmb() #else /* Depends on MIPS II instruction set */ diff --git a/arch/mips/include/asm/ptrace.h b/arch/mips/include/asm/ptrace.h index cb88d6d4f9..60f50450d4 100644 --- a/arch/mips/include/asm/ptrace.h +++ b/arch/mips/include/asm/ptrace.h @@ -36,7 +36,7 @@ struct pt_regs { unsigned long cp0_badvaddr; unsigned long cp0_cause; unsigned long cp0_epc; -#ifdef CONFIG_CPU_CAVIUM_OCTEON +#ifdef CONFIG_CPU_MIPS64_OCTEON unsigned long long mpl[6]; /* MTM{0-5} */ unsigned long long mtp[6]; /* MTP{0-5} */ #endif diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt index 7a5da9d822..303a23fdd1 100644 --- a/scripts/config_whitelist.txt +++ b/scripts/config_whitelist.txt @@ -234,7 +234,6 @@ CONFIG_CPLD_BR_PRELIM CONFIG_CPLD_OR_PRELIM CONFIG_CPM2 CONFIG_CPU_ARMV8 -CONFIG_CPU_CAVIUM_OCTEON CONFIG_CPU_FREQ_HZ CONFIG_CPU_HAS_LLSC CONFIG_CPU_HAS_PREFETCH From patchwork Sat May 2 08:59:40 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Stefan Roese X-Patchwork-Id: 244770 List-Id: U-Boot discussion From: sr at denx.de (Stefan Roese) Date: Sat, 2 May 2020 10:59:40 +0200 Subject: [PATCH v1 06/10] mips: mipsregs.h: Add more register macros for Octeon port In-Reply-To: <20200502085944.13444-1-sr@denx.de> References: <20200502085944.13444-1-sr@denx.de> Message-ID: <20200502085944.13444-7-sr@denx.de> From: Aaron Williams Thips patch adds some more register definitions which will be used by the Octeon platform. Signed-off-by: Aaron Williams Signed-off-by: Stefan Roese --- arch/mips/include/asm/mipsregs.h | 19 ++++++++++++++++++- 1 file changed, 18 insertions(+), 1 deletion(-) diff --git a/arch/mips/include/asm/mipsregs.h b/arch/mips/include/asm/mipsregs.h index f80311e64e..459ef43fa6 100644 --- a/arch/mips/include/asm/mipsregs.h +++ b/arch/mips/include/asm/mipsregs.h @@ -40,15 +40,20 @@ #define CP0_CONF $3 #define CP0_GLOBALNUMBER $3, 1 #define CP0_CONTEXT $4 +#define CP0_USERLOCAL $4, 2 #define CP0_PAGEMASK $5 +#define CP0_PAGEGRAIN $5, 1 #define CP0_WIRED $6 #define CP0_INFO $7 #define CP0_HWRENA $7, 0 #define CP0_BADVADDR $8 #define CP0_BADINSTR $8, 1 #define CP0_COUNT $9 +#define CP0_CVMCOUNT $9, 6 +#define CP0_CVMCTL $9, 7 #define CP0_ENTRYHI $10 #define CP0_COMPARE $11 +#define CP0_CVMMEMCTL $11, 7 #define CP0_STATUS $12 #define CP0_CAUSE $13 #define CP0_EPC $14 @@ -56,8 +61,11 @@ #define CP0_EBASE $15, 1 #define CP0_CMGCRBASE $15, 3 #define CP0_CONFIG $16 +#define CP0_CONFIG1 $16, 1 #define CP0_CONFIG3 $16, 3 +#define CP0_CONFIG4 $16, 4 #define CP0_CONFIG5 $16, 5 +#define CP0_CVMMEMCTL2 $16, 6 #define CP0_LLADDR $17 #define CP0_WATCHLO $18 #define CP0_WATCHHI $19 @@ -67,13 +75,22 @@ #define CP0_DEBUG $23 #define CP0_DEPC $24 #define CP0_PERFORMANCE $25 +#define CP0_PERF_CNT0 $25, 1 +#define CP0_PERF_CNT1 $25, 3 +#define CP0_PERF_CNT2 $25, 5 +#define CP0_PERF_CNT3 $25, 7 #define CP0_ECC $26 #define CP0_CACHEERR $27 +#define CP0_CACHEERR_ICACHE $27 +#define CP0_CACHEERR_DCACHE $27, 1 #define CP0_TAGLO $28 #define CP0_TAGHI $29 #define CP0_ERROREPC $30 #define CP0_DESAVE $31 - +#define CP0_KSCRATCH1 $31, 2 +#define CP0_KSCRATCH2 $31, 3 +#define CP0_KSCRATCH3 $31, 4 +#define CP0_KSCRATCH4 $31, 5 /* * R4640/R4650 cp0 register names. These registers are listed * here only for completeness; without MMU these CPUs are not useable From patchwork Sat May 2 08:59:41 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Stefan Roese X-Patchwork-Id: 244771 List-Id: U-Boot discussion From: sr at denx.de (Stefan Roese) Date: Sat, 2 May 2020 10:59:41 +0200 Subject: [PATCH v1 07/10] mips: mipsregs.h: Sync with linux v5.7.0-rc3 version In-Reply-To: <20200502085944.13444-1-sr@denx.de> References: <20200502085944.13444-1-sr@denx.de> Message-ID: <20200502085944.13444-8-sr@denx.de> Using .set mips3/32/64 without .set push/pop is fragile. This patch solves this issue by sync'ing the inline-asm functions with the latest Linux ones. Signed-off-by: Stefan Roese --- arch/mips/include/asm/mipsregs.h | 44 +++++++++++++++++++------------- 1 file changed, 26 insertions(+), 18 deletions(-) diff --git a/arch/mips/include/asm/mipsregs.h b/arch/mips/include/asm/mipsregs.h index 459ef43fa6..bf09e35e16 100644 --- a/arch/mips/include/asm/mipsregs.h +++ b/arch/mips/include/asm/mipsregs.h @@ -934,9 +934,10 @@ do { \ : "=r" (__res)); \ else \ __asm__ __volatile__( \ + ".set\tpush\n\t" \ ".set\tmips32\n\t" \ "mfc0\t%0, " #source ", " #sel "\n\t" \ - ".set\tmips0\n\t" \ + ".set\tpop\n\t" \ : "=r" (__res)); \ __res; \ }) @@ -947,15 +948,17 @@ do { \ __res = __read_64bit_c0_split(source, sel); \ else if (sel == 0) \ __asm__ __volatile__( \ + ".set\tpush\n\t" \ ".set\tmips3\n\t" \ "dmfc0\t%0, " #source "\n\t" \ - ".set\tmips0" \ + ".set\tpop" \ : "=r" (__res)); \ else \ __asm__ __volatile__( \ + ".set\tpush\n\t" \ ".set\tmips64\n\t" \ "dmfc0\t%0, " #source ", " #sel "\n\t" \ - ".set\tmips0" \ + ".set\tpop" \ : "=r" (__res)); \ __res; \ }) @@ -968,9 +971,10 @@ do { \ : : "Jr" ((unsigned int)(value))); \ else \ __asm__ __volatile__( \ + ".set\tpush\n\t" \ ".set\tmips32\n\t" \ "mtc0\t%z0, " #register ", " #sel "\n\t" \ - ".set\tmips0" \ + ".set\tpop" \ : : "Jr" ((unsigned int)(value))); \ } while (0) @@ -980,15 +984,17 @@ do { \ __write_64bit_c0_split(register, sel, value); \ else if (sel == 0) \ __asm__ __volatile__( \ + ".set\tpush\n\t" \ ".set\tmips3\n\t" \ "dmtc0\t%z0, " #register "\n\t" \ - ".set\tmips0" \ + ".set\tpop" \ : : "Jr" (value)); \ else \ __asm__ __volatile__( \ + ".set\tpush\n\t" \ ".set\tmips64\n\t" \ "dmtc0\t%z0, " #register ", " #sel "\n\t" \ - ".set\tmips0" \ + ".set\tpop" \ : : "Jr" (value)); \ } while (0) @@ -1033,21 +1039,21 @@ do { \ \ if (sel == 0) \ __asm__ __volatile__( \ + ".set\tpush\n\t" \ ".set\tmips64\n\t" \ - "dmfc0\t%M0, " #source "\n\t" \ - "dsll\t%L0, %M0, 32\n\t" \ - "dsra\t%M0, %M0, 32\n\t" \ - "dsra\t%L0, %L0, 32\n\t" \ - ".set\tmips0" \ + "dmfc0\t%L0, " #source "\n\t" \ + "dsra\t%M0, %L0, 32\n\t" \ + "sll\t%L0, %L0, 0\n\t" \ + ".set\tpop" \ : "=r" (__val)); \ else \ __asm__ __volatile__( \ + ".set\tpush\n\t" \ ".set\tmips64\n\t" \ - "dmfc0\t%M0, " #source ", " #sel "\n\t" \ - "dsll\t%L0, %M0, 32\n\t" \ - "dsra\t%M0, %M0, 32\n\t" \ - "dsra\t%L0, %L0, 32\n\t" \ - ".set\tmips0" \ + "dmfc0\t%L0, " #source ", " #sel "\n\t" \ + "dsra\t%M0, %L0, 32\n\t" \ + "sll\t%L0, %L0, 0\n\t" \ + ".set\tpop" \ : "=r" (__val)); \ \ __val; \ @@ -1057,23 +1063,25 @@ do { \ do { \ if (sel == 0) \ __asm__ __volatile__( \ + ".set\tpush\n\t" \ ".set\tmips64\n\t" \ "dsll\t%L0, %L0, 32\n\t" \ "dsrl\t%L0, %L0, 32\n\t" \ "dsll\t%M0, %M0, 32\n\t" \ "or\t%L0, %L0, %M0\n\t" \ "dmtc0\t%L0, " #source "\n\t" \ - ".set\tmips0" \ + ".set\tpop" \ : : "r" (val)); \ else \ __asm__ __volatile__( \ + ".set\tpush\n\t" \ ".set\tmips64\n\t" \ "dsll\t%L0, %L0, 32\n\t" \ "dsrl\t%L0, %L0, 32\n\t" \ "dsll\t%M0, %M0, 32\n\t" \ "or\t%L0, %L0, %M0\n\t" \ "dmtc0\t%L0, " #source ", " #sel "\n\t" \ - ".set\tmips0" \ + ".set\tpop" \ : : "r" (val)); \ } while (0) From patchwork Sat May 2 08:59:42 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Stefan Roese X-Patchwork-Id: 244772 List-Id: U-Boot discussion From: sr at denx.de (Stefan Roese) Date: Sat, 2 May 2020 10:59:42 +0200 Subject: [PATCH v1 08/10] sysreset: Add Octeon sysreset driver In-Reply-To: <20200502085944.13444-1-sr@denx.de> References: <20200502085944.13444-1-sr@denx.de> Message-ID: <20200502085944.13444-9-sr@denx.de> This patch adds a UCLASS_SYSRESET sysreset driver for the Octeon SoC family. Signed-off-by: Stefan Roese --- drivers/sysreset/Kconfig | 7 ++++ drivers/sysreset/Makefile | 1 + drivers/sysreset/sysreset_octeon.c | 52 ++++++++++++++++++++++++++++++ 3 files changed, 60 insertions(+) create mode 100644 drivers/sysreset/sysreset_octeon.c diff --git a/drivers/sysreset/Kconfig b/drivers/sysreset/Kconfig index 4be7433404..6ebc90e1d3 100644 --- a/drivers/sysreset/Kconfig +++ b/drivers/sysreset/Kconfig @@ -57,6 +57,13 @@ config SYSRESET_MICROBLAZE help This is soft reset on Microblaze which does jump to 0x0 address. +config SYSRESET_OCTEON + bool "Enable support for Marvell Octeon SoC family" + depends on ARCH_OCTEON + help + This enables the system reset driver support for Marvell Octeon + SoCs. + config SYSRESET_PSCI bool "Enable support for PSCI System Reset" depends on ARM_PSCI_FW diff --git a/drivers/sysreset/Makefile b/drivers/sysreset/Makefile index 3ed4bab9e3..df2293b848 100644 --- a/drivers/sysreset/Makefile +++ b/drivers/sysreset/Makefile @@ -10,6 +10,7 @@ obj-$(CONFIG_SANDBOX) += sysreset_sandbox.o obj-$(CONFIG_SYSRESET_GPIO) += sysreset_gpio.o obj-$(CONFIG_SYSRESET_MPC83XX) += sysreset_mpc83xx.o obj-$(CONFIG_SYSRESET_MICROBLAZE) += sysreset_microblaze.o +obj-$(CONFIG_SYSRESET_OCTEON) += sysreset_octeon.o obj-$(CONFIG_SYSRESET_PSCI) += sysreset_psci.o obj-$(CONFIG_SYSRESET_SOCFPGA) += sysreset_socfpga.o obj-$(CONFIG_SYSRESET_SOCFPGA_S10) += sysreset_socfpga_s10.o diff --git a/drivers/sysreset/sysreset_octeon.c b/drivers/sysreset/sysreset_octeon.c new file mode 100644 index 0000000000..a05dac3226 --- /dev/null +++ b/drivers/sysreset/sysreset_octeon.c @@ -0,0 +1,52 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2020 Stefan Roese + */ + +#include +#include +#include +#include +#include + +#define RST_SOFT_RST 0x0080 + +struct octeon_sysreset_data { + void __iomem *base; +}; + +static int octeon_sysreset_request(struct udevice *dev, enum sysreset_t type) +{ + struct octeon_sysreset_data *data = dev_get_priv(dev); + + writeq(1, data->base + RST_SOFT_RST); + + return -EINPROGRESS; +} + +static int octeon_sysreset_probe(struct udevice *dev) +{ + struct octeon_sysreset_data *data = dev_get_priv(dev); + + data->base = dev_remap_addr(dev); + + return 0; +} + +static struct sysreset_ops octeon_sysreset = { + .request = octeon_sysreset_request, +}; + +static const struct udevice_id octeon_sysreset_ids[] = { + { .compatible = "mrvl,cn7xxx-rst" }, + { } +}; + +U_BOOT_DRIVER(sysreset_octeon) = { + .id = UCLASS_SYSRESET, + .name = "octeon_sysreset", + .priv_auto_alloc_size = sizeof(struct octeon_sysreset_data), + .ops = &octeon_sysreset, + .probe = octeon_sysreset_probe, + .of_match = octeon_sysreset_ids, +}; From patchwork Sat May 2 08:59:43 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Stefan Roese X-Patchwork-Id: 244774 List-Id: U-Boot discussion From: sr at denx.de (Stefan Roese) Date: Sat, 2 May 2020 10:59:43 +0200 Subject: [PATCH v1 09/10] mips: octeon: dts: Add Octeon 3 cn73xx base dtsi file In-Reply-To: <20200502085944.13444-1-sr@denx.de> References: <20200502085944.13444-1-sr@denx.de> Message-ID: <20200502085944.13444-10-sr@denx.de> This patch adds the base dtsi file for the Octeon 3 cn73xx SoC. Signed-off-by: Stefan Roese --- MAINTAINERS | 1 + arch/mips/dts/mrvl,cn73xx.dtsi | 64 ++++++++++++++++++++++++++++++++++ 2 files changed, 65 insertions(+) create mode 100644 arch/mips/dts/mrvl,cn73xx.dtsi diff --git a/MAINTAINERS b/MAINTAINERS index 29f2d7328c..71d257c214 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -754,6 +754,7 @@ M: Aaron Williams S: Maintained F: arch/mips/mach-octeon/ F: arch/mips/include/asm/arch-octeon/ +F: arch/mips/dts/mrvl,cn73xx.dtsi MMC M: Peng Fan diff --git a/arch/mips/dts/mrvl,cn73xx.dtsi b/arch/mips/dts/mrvl,cn73xx.dtsi new file mode 100644 index 0000000000..90872a3b4b --- /dev/null +++ b/arch/mips/dts/mrvl,cn73xx.dtsi @@ -0,0 +1,64 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Marvell / Cavium Inc. CN73xx + */ + +/dts-v1/; + +/ { + #address-cells = <2>; + #size-cells = <2>; + + soc at 0 { + interrupt-parent = <&ciu3>; + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <2>; + ranges; /* Direct mapping */ + + ciu3: interrupt-controller at 1010000000000 { + compatible = "cavium,octeon-7890-ciu3"; + interrupt-controller; + /* + * Interrupts are specified by two parts: + * 1) Source number (20 significant bits) + * 2) Trigger type: (4 == level, 1 == edge) + */ + #address-cells = <0>; + #interrupt-cells = <2>; + reg = <0x10100 0x00000000 0x0 0xb0000000>; + }; + + bootbus: bootbus at 1180000000000 { + compatible = "cavium,octeon-3860-bootbus","simple-bus"; + reg = <0x11800 0x00000000 0x0 0x200>; + /* The chip select number and offset */ + #address-cells = <2>; + /* The size of the chip select region */ + #size-cells = <1>; + }; + + reset: reset at 1180006001600 { + compatible = "mrvl,cn7xxx-rst"; + reg = <0x11800 0x06001600 0x0 0x200>; + }; + + uart0: serial at 1180000000800 { + compatible = "cavium,octeon-3860-uart","ns16550"; + reg = <0x11800 0x00000800 0x0 0x400>; + clock-frequency = <0>; + current-speed = <115200>; + reg-shift = <3>; + interrupts = <0x08000 4>; + }; + + uart1: serial at 1180000000c00 { + compatible = "cavium,octeon-3860-uart","ns16550"; + reg = <0x11800 0x00000c00 0x0 0x400>; + clock-frequency = <0>; + current-speed = <115200>; + reg-shift = <3>; + interrupts = <0x08040 4>; + }; + }; +}; From patchwork Sat May 2 08:59:44 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Stefan Roese X-Patchwork-Id: 244773 List-Id: U-Boot discussion From: sr at denx.de (Stefan Roese) Date: Sat, 2 May 2020 10:59:44 +0200 Subject: [PATCH v1 10/10] mips: octeon: Add minimal Octeon 3 EBB7304 EVK support In-Reply-To: <20200502085944.13444-1-sr@denx.de> References: <20200502085944.13444-1-sr@denx.de> Message-ID: <20200502085944.13444-11-sr@denx.de> This patch adds very basic minimal support for the Marvell Octeon 3 CN73xx based EBB7304 EVK. Please note that the basic Octeon port does not support DDR3/4 initialization yet. To still use U-Boot on with this port, the L2 cache (4MiB) is used as RAM. This way, U-Boot can boot to the prompt on this board. Supported devices: - UART - reset - CFI parallel NOR flash Signed-off-by: Stefan Roese --- arch/mips/dts/Makefile | 1 + arch/mips/dts/mrvl,octeon-ebb7304.dts | 96 ++++++++++++++++++++++++ arch/mips/mach-octeon/Kconfig | 14 ++++ board/Marvell/octeon_ebb7304/Kconfig | 19 +++++ board/Marvell/octeon_ebb7304/MAINTAINERS | 7 ++ board/Marvell/octeon_ebb7304/Makefile | 8 ++ board/Marvell/octeon_ebb7304/board.c | 12 +++ configs/octeon_ebb7304_defconfig | 34 +++++++++ include/configs/octeon_common.h | 29 +++++++ include/configs/octeon_ebb7304.h | 20 +++++ 10 files changed, 240 insertions(+) create mode 100644 arch/mips/dts/mrvl,octeon-ebb7304.dts create mode 100644 board/Marvell/octeon_ebb7304/Kconfig create mode 100644 board/Marvell/octeon_ebb7304/MAINTAINERS create mode 100644 board/Marvell/octeon_ebb7304/Makefile create mode 100644 board/Marvell/octeon_ebb7304/board.c create mode 100644 configs/octeon_ebb7304_defconfig create mode 100644 include/configs/octeon_common.h create mode 100644 include/configs/octeon_ebb7304.h diff --git a/arch/mips/dts/Makefile b/arch/mips/dts/Makefile index f711e9fb59..dc85901dca 100644 --- a/arch/mips/dts/Makefile +++ b/arch/mips/dts/Makefile @@ -18,6 +18,7 @@ dtb-$(CONFIG_BOARD_COMTREND_VR3032U) += comtrend,vr-3032u.dtb dtb-$(CONFIG_BOARD_COMTREND_WAP5813N) += comtrend,wap-5813n.dtb dtb-$(CONFIG_BOARD_HUAWEI_HG556A) += huawei,hg556a.dtb dtb-$(CONFIG_BOARD_MT7628_RFB) += mediatek,mt7628-rfb.dtb +dtb-$(CONFIG_TARGET_OCTEON_EBB7304) += mrvl,octeon-ebb7304.dtb dtb-$(CONFIG_BOARD_NETGEAR_CG3100D) += netgear,cg3100d.dtb dtb-$(CONFIG_BOARD_NETGEAR_DGND3700V2) += netgear,dgnd3700v2.dtb dtb-$(CONFIG_BOARD_SAGEM_FAST1704) += sagem,f at st1704.dtb diff --git a/arch/mips/dts/mrvl,octeon-ebb7304.dts b/arch/mips/dts/mrvl,octeon-ebb7304.dts new file mode 100644 index 0000000000..4e9c2de7d4 --- /dev/null +++ b/arch/mips/dts/mrvl,octeon-ebb7304.dts @@ -0,0 +1,96 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Marvell / Cavium Inc. EVB CN7300 + */ + +/dts-v1/; + +/include/ "mrvl,cn73xx.dtsi" + +/ { + model = "cavium,ebb7304"; + compatible = "cavium,ebb7304"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = &uart0; + }; +}; + +&bootbus { + /* + * bootbus CS0 for CFI flash is remapped (0x1fc0.0000 -> 1f40.0000) + * as the initial size is too small for the 8MiB flash device + */ + ranges = <0 0 0 0x1f400000 0xc00000>, + <1 0 0x10000 0x10000000 0>, + <2 0 0x10000 0x20000000 0>, + <3 0 0x10000 0x30000000 0>, + <4 0 0 0x1d020000 0x10000>, + <5 0 0x10000 0x50000000 0>, + <6 0 0x10000 0x60000000 0>, + <7 0 0x10000 0x70000000 0>; + + cavium,cs-config at 0 { + compatible = "cavium,octeon-3860-bootbus-config"; + cavium,cs-index = <0>; + cavium,t-adr = <10>; + cavium,t-ce = <50>; + cavium,t-oe = <50>; + cavium,t-we = <35>; + cavium,t-rd-hld = <25>; + cavium,t-wr-hld = <35>; + cavium,t-pause = <0>; + cavium,t-wait = <50>; + cavium,t-page = <30>; + cavium,t-rd-dly = <0>; + cavium,page-mode = <1>; + cavium,pages = <8>; + cavium,bus-width = <8>; + }; + + cavium,cs-config at 4 { + compatible = "cavium,octeon-3860-bootbus-config"; + cavium,cs-index = <4>; + cavium,t-adr = <10>; + cavium,t-ce = <10>; + cavium,t-oe = <160>; + cavium,t-we = <100>; + cavium,t-rd-hld = <10>; + cavium,t-wr-hld = <0>; + cavium,t-pause = <50>; + cavium,t-wait = <50>; + cavium,t-page = <10>; + cavium,t-rd-dly = <10>; + cavium,pages = <0>; + cavium,bus-width = <8>; + }; + + flash0: nor at 0,0 { + compatible = "cfi-flash"; + reg = <0 0 0x800000>; + #address-cells = <1>; + #size-cells = <1>; + partition at 0 { + label = "bootloader"; + reg = <0 0x340000>; + read-only; + }; + partition at 300000 { + label = "storage"; + reg = <0x340000 0x4be000>; + }; + partition at 7fe000 { + label = "environment"; + reg = <0x7fe000 0x2000>; + read-only; + }; + }; +}; + +&uart0 { + clock-frequency = <1200000000>; +}; diff --git a/arch/mips/mach-octeon/Kconfig b/arch/mips/mach-octeon/Kconfig index 67fcb6058c..3b615e71ac 100644 --- a/arch/mips/mach-octeon/Kconfig +++ b/arch/mips/mach-octeon/Kconfig @@ -36,6 +36,18 @@ config SOC_OCTEON3 endchoice +choice + prompt "Octeon 3 board select" + default TARGET_OCTEON_EBB7304 + +config TARGET_OCTEON_EBB7304 + bool "Marvell Octeon EBB7304" + select OCTEON_CN73XX + help + Choose this for the Octeon EBB7304 board + +endchoice + config SYS_DCACHE_SIZE default 32768 @@ -89,4 +101,6 @@ config OCTEON_L2_MEMCPY_ADDR This specifies where U-Boot will place the memcpy routine used for copying U-Boot from flash to L2 cache. +source "board/Marvell/octeon_ebb7304/Kconfig" + endmenu diff --git a/board/Marvell/octeon_ebb7304/Kconfig b/board/Marvell/octeon_ebb7304/Kconfig new file mode 100644 index 0000000000..ab54e6dbbc --- /dev/null +++ b/board/Marvell/octeon_ebb7304/Kconfig @@ -0,0 +1,19 @@ +if TARGET_OCTEON_EBB7304 + +config SYS_BOARD + string + default "octeon_ebb7304" + +config SYS_VENDOR + string + default "Marvell" + +config SYS_CONFIG_NAME + string + default "octeon_ebb7304" + +config DEFAULT_DEVICE_TREE + string + default "mrvl,octeon-ebb7304" + +endif diff --git a/board/Marvell/octeon_ebb7304/MAINTAINERS b/board/Marvell/octeon_ebb7304/MAINTAINERS new file mode 100644 index 0000000000..f52beacbac --- /dev/null +++ b/board/Marvell/octeon_ebb7304/MAINTAINERS @@ -0,0 +1,7 @@ +OCTEON_EBB7304 BOARD +M: Aaron Williams +S: Maintained +F: board/Marvell/octeon_ebb7304 +F: configs/octeon_ebb7304_defconfig +F: include/configs/octeon_ebb7304.h +F: arch/mips/dts/mrvl,octeon-ebb7304.dts diff --git a/board/Marvell/octeon_ebb7304/Makefile b/board/Marvell/octeon_ebb7304/Makefile new file mode 100644 index 0000000000..8c6ffb9328 --- /dev/null +++ b/board/Marvell/octeon_ebb7304/Makefile @@ -0,0 +1,8 @@ +# +# Copyright (C) 2016 Stefan Roese +# Copyright (C) 2019 Marvell International Ltd. +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y := board.o diff --git a/board/Marvell/octeon_ebb7304/board.c b/board/Marvell/octeon_ebb7304/board.c new file mode 100644 index 0000000000..41ac18b952 --- /dev/null +++ b/board/Marvell/octeon_ebb7304/board.c @@ -0,0 +1,12 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2020 Stefan Roese + */ + +#include +#include + +/* + * Nothing included right now. Code will be added in follow-up + * patches. + */ diff --git a/configs/octeon_ebb7304_defconfig b/configs/octeon_ebb7304_defconfig new file mode 100644 index 0000000000..5fe56ac6bc --- /dev/null +++ b/configs/octeon_ebb7304_defconfig @@ -0,0 +1,34 @@ +CONFIG_MIPS=y +CONFIG_SYS_TEXT_BASE=0xFFFFFFFFC0000000 +CONFIG_SYS_MALLOC_F_LEN=0x4000 +CONFIG_ENV_SIZE=0x2000 +CONFIG_ENV_SECT_SIZE=0x10000 +CONFIG_NR_DRAM_BANKS=2 +CONFIG_DEBUG_UART_BASE=0x8001180000000800 +CONFIG_DEBUG_UART_CLOCK=1200000000 +CONFIG_ARCH_OCTEON=y +CONFIG_DEBUG_UART=y +CONFIG_SYS_CONSOLE_INFO_QUIET=y +CONFIG_HUSH_PARSER=y +CONFIG_CMD_MTD=y +CONFIG_CMD_PCI=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_PING=y +CONFIG_CMD_TIME=y +CONFIG_ENV_IS_IN_FLASH=y +CONFIG_ENV_ADDR=0x1FBFE000 +CONFIG_MTD=y +CONFIG_DM_MTD=y +CONFIG_MTD_NOR_FLASH=y +CONFIG_FLASH_CFI_DRIVER=y +CONFIG_CFI_FLASH=y +CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y +CONFIG_FLASH_CFI_MTD=y +CONFIG_SYS_FLASH_CFI=y +CONFIG_DM_ETH=y +CONFIG_DEBUG_UART_SHIFT=3 +CONFIG_DEBUG_UART_ANNOUNCE=y +CONFIG_SYS_NS16550=y +CONFIG_SYSRESET=y +CONFIG_SYSRESET_OCTEON=y +CONFIG_HEXDUMP=y diff --git a/include/configs/octeon_common.h b/include/configs/octeon_common.h new file mode 100644 index 0000000000..b805d09ac1 --- /dev/null +++ b/include/configs/octeon_common.h @@ -0,0 +1,29 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2019-2020 + * Marvell + */ + +#ifndef __OCTEON_COMMON_H__ +#define __OCTEON_COMMON_H__ + +#ifndef __ASSEMBLY__ +extern int octeon_get_timer_freq(void); +#endif + +#define CONFIG_SYS_MIPS_TIMER_FREQ octeon_get_timer_freq() + +/* No DDR init yet -> run in L2 cache with limited resources */ +#define CONFIG_SYS_MALLOC_LEN (256 << 10) +#define CONFIG_SYS_SDRAM_BASE (0xffffffffc0000000 + 0x100000) +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE + +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + (1 << 20)) + +/* + * Set a max image size for the image (incl. DTB), so that a growing + * image will not exceed this maximum size + */ +#define CONFIG_BOARD_SIZE_LIMIT 0x100000 /* 1MiB */ + +#endif /* __OCTEON_COMMON_H__ */ diff --git a/include/configs/octeon_ebb7304.h b/include/configs/octeon_ebb7304.h new file mode 100644 index 0000000000..04fe4dfe22 --- /dev/null +++ b/include/configs/octeon_ebb7304.h @@ -0,0 +1,20 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2019-2020 + * Marvell + */ + +#ifndef __CONFIG_H__ +#define __CONFIG_H__ + +#include "octeon_common.h" + +/* + * CFI flash + */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +#define CONFIG_SYS_MAX_FLASH_SECT 256 +#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT +#define CONFIG_SYS_FLASH_EMPTY_INFO /* flinfo indicates empty blocks */ + +#endif /* __CONFIG_H__ */