From patchwork Thu Jul 9 17:41:26 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Nicolas Saenz Julienne X-Patchwork-Id: 241143 List-Id: U-Boot discussion From: nsaenzjulienne at suse.de (Nicolas Saenz Julienne) Date: Thu, 09 Jul 2020 19:41:26 +0200 Subject: [PATCH] include/bitfield.h: include byteorder.h In-Reply-To: References: <20200525113959.11886-1-s.nawrocki@samsung.com> <20200525113959.11886-7-s.nawrocki@samsung.com> <493671a5-2fd5-71dc-a15f-6ce2169a63ef@suse.com> Message-ID: This is needed in order to use the cpu_to_*()/*_to_cpu() family of functions. Signed-off-by: Nicolas Saenz Julienne --- IMO the ideal thing would be to squash this into the original patch. include/linux/bitfield.h | 1 + 1 file changed, 1 insertion(+) diff --git a/include/linux/bitfield.h b/include/linux/bitfield.h index 7ad8b088ed..7ad02f8cbb 100644 --- a/include/linux/bitfield.h +++ b/include/linux/bitfield.h @@ -16,6 +16,7 @@ #define _LINUX_BITFIELD_H #include +#include /* * Bitfield access macros From patchwork Mon May 25 11:39:52 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: "Sylwester Nawrocki/Kernel \\\(PLT\\\) /SRPOL/Staff Engineer/Samsung Electronics" X-Patchwork-Id: 246502 List-Id: U-Boot discussion From: s.nawrocki at samsung.com (Sylwester Nawrocki) Date: Mon, 25 May 2020 13:39:52 +0200 Subject: [PATCH v4 2/9] usb: xhci: Use only 32-bit accesses in xhci_writeq/xhci_readq In-Reply-To: <20200525113959.11886-1-s.nawrocki@samsung.com> References: <20200525113959.11886-1-s.nawrocki@samsung.com> Message-ID: <20200525113959.11886-3-s.nawrocki@samsung.com> There might be hardware configurations where 64-bit data accesses to XHCI registers are not supported properly. This patch removes the readq/writeq so always two 32-bit accesses are used to read/write 64-bit XHCI registers, similarly as it is done in Linux kernel. This patch fixes operation of the XHCI controller on RPI4 Broadcom BCM2711 SoC based board, where the VL805 USB XHCI controller is connected to the PCIe Root Complex, which is attached to the system through the SCB bridge. Even though the architecture is 64-bit the PCIe BAR is 32-bit and likely the 64-bit wide register accesses initiated by the CPU are not properly translated to a sequence of 32-bit PCIe accesses. xhci_readq(), for example, always returns same value in upper and lower 32-bits, e.g. 0xabcd1234abcd1234 instead of 0x00000000abcd1234. Cc: Sergey Temerkhanov Signed-off-by: Sylwester Nawrocki Reviewed-by: Bin Meng Reviewed-by: Nicolas Saenz Julienne --- Changes since v1: - none. Changes since RFC: - dropped Kconfig option, switched to not using readq/writeq unconditionally. --- include/usb/xhci.h | 8 -------- 1 file changed, 8 deletions(-) diff --git a/include/usb/xhci.h b/include/usb/xhci.h index 6017504..c16106a 100644 --- a/include/usb/xhci.h +++ b/include/usb/xhci.h @@ -1111,28 +1111,20 @@ static inline void xhci_writel(uint32_t volatile *regs, const unsigned int val) */ static inline u64 xhci_readq(__le64 volatile *regs) { -#if BITS_PER_LONG == 64 - return readq(regs); -#else __u32 *ptr = (__u32 *)regs; u64 val_lo = readl(ptr); u64 val_hi = readl(ptr + 1); return val_lo + (val_hi << 32); -#endif } static inline void xhci_writeq(__le64 volatile *regs, const u64 val) { -#if BITS_PER_LONG == 64 - writeq(val, regs); -#else __u32 *ptr = (__u32 *)regs; u32 val_lo = lower_32_bits(val); /* FIXME */ u32 val_hi = upper_32_bits(val); writel(val_lo, ptr); writel(val_hi, ptr + 1); -#endif } int xhci_hcd_init(int index, struct xhci_hccr **ret_hccr, From patchwork Mon May 25 11:39:53 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: "Sylwester Nawrocki/Kernel \\\(PLT\\\) /SRPOL/Staff Engineer/Samsung Electronics" X-Patchwork-Id: 246503 List-Id: U-Boot discussion From: s.nawrocki at samsung.com (Sylwester Nawrocki) Date: Mon, 25 May 2020 13:39:53 +0200 Subject: [PATCH v4 3/9] pci: Move some PCIe register offset definitions to a common header In-Reply-To: <20200525113959.11886-1-s.nawrocki@samsung.com> References: <20200525113959.11886-1-s.nawrocki@samsung.com> Message-ID: <20200525113959.11886-4-s.nawrocki@samsung.com> Some PCI Express register offsets are currently defined in multiple drivers, move them to a common header to avoid re-definitions and as a pre-requisite for adding new PCIe driver. While at it replace some spaces with tabs. Signed-off-by: Sylwester Nawrocki Reviewed-by: Bin Meng Reviewed-by: Nicolas Saenz Julienne --- Changes since v1: - none. Changes since RFC: - whitespace clean up. --- drivers/pci/pci-rcar-gen3.c | 8 -------- drivers/pci/pcie_intel_fpga.c | 3 --- include/pci.h | 13 +++++++++++-- 3 files changed, 11 insertions(+), 13 deletions(-) diff --git a/drivers/pci/pci-rcar-gen3.c b/drivers/pci/pci-rcar-gen3.c index 30eff67..393f1c9 100644 --- a/drivers/pci/pci-rcar-gen3.c +++ b/drivers/pci/pci-rcar-gen3.c @@ -117,14 +117,6 @@ #define RCAR_PCI_MAX_RESOURCES 4 #define MAX_NR_INBOUND_MAPS 6 -#define PCI_EXP_FLAGS 2 /* Capabilities register */ -#define PCI_EXP_FLAGS_TYPE 0x00f0 /* Device/Port type */ -#define PCI_EXP_TYPE_ROOT_PORT 0x4 /* Root Port */ -#define PCI_EXP_LNKCAP 12 /* Link Capabilities */ -#define PCI_EXP_LNKCAP_DLLLARC 0x00100000 /* Data Link Layer Link Active Reporting Capable */ -#define PCI_EXP_SLTCAP 20 /* Slot Capabilities */ -#define PCI_EXP_SLTCAP_PSN 0xfff80000 /* Physical Slot Number */ - enum { RCAR_PCI_ACCESS_READ, RCAR_PCI_ACCESS_WRITE, diff --git a/drivers/pci/pcie_intel_fpga.c b/drivers/pci/pcie_intel_fpga.c index 6a9f29c..69363a0 100644 --- a/drivers/pci/pcie_intel_fpga.c +++ b/drivers/pci/pcie_intel_fpga.c @@ -65,9 +65,6 @@ #define IS_ROOT_PORT(pcie, bdf) \ ((PCI_BUS(bdf) == pcie->first_busno) ? true : false) -#define PCI_EXP_LNKSTA 18 /* Link Status */ -#define PCI_EXP_LNKSTA_DLLLA 0x2000 /* Data Link Layer Link Active */ - /** * struct intel_fpga_pcie - Intel FPGA PCIe controller state * @bus: Pointer to the PCI bus diff --git a/include/pci.h b/include/pci.h index aff56b2..dfdbb32 100644 --- a/include/pci.h +++ b/include/pci.h @@ -471,10 +471,19 @@ #define PCI_EA_FIELD_MASK 0xfffffffc /* For Base & Max Offset */ /* PCI Express capabilities */ +#define PCI_EXP_FLAGS 2 /* Capabilities register */ +#define PCI_EXP_FLAGS_TYPE 0x00f0 /* Device/Port type */ +#define PCI_EXP_TYPE_ROOT_PORT 0x4 /* Root Port */ #define PCI_EXP_DEVCAP 4 /* Device capabilities */ -#define PCI_EXP_DEVCAP_FLR 0x10000000 /* Function Level Reset */ +#define PCI_EXP_DEVCAP_FLR 0x10000000 /* Function Level Reset */ #define PCI_EXP_DEVCTL 8 /* Device Control */ -#define PCI_EXP_DEVCTL_BCR_FLR 0x8000 /* Bridge Configuration Retry / FLR */ +#define PCI_EXP_DEVCTL_BCR_FLR 0x8000 /* Bridge Configuration Retry / FLR */ +#define PCI_EXP_LNKCAP 12 /* Link Capabilities */ +#define PCI_EXP_LNKCAP_DLLLARC 0x00100000 /* Data Link Layer Link Active Reporting Capable */ +#define PCI_EXP_LNKSTA 18 /* Link Status */ +#define PCI_EXP_LNKSTA_DLLLA 0x2000 /* Data Link Layer Link Active */ +#define PCI_EXP_SLTCAP 20 /* Slot Capabilities */ +#define PCI_EXP_SLTCAP_PSN 0xfff80000 /* Physical Slot Number */ /* Include the ID list */ From patchwork Mon May 25 11:39:54 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: "Sylwester Nawrocki/Kernel \\\(PLT\\\) /SRPOL/Staff Engineer/Samsung Electronics" X-Patchwork-Id: 246504 List-Id: U-Boot discussion From: s.nawrocki at samsung.com (Sylwester Nawrocki) Date: Mon, 25 May 2020 13:39:54 +0200 Subject: [PATCH v4 4/9] rpi4: shorten a mapping for the DRAM In-Reply-To: <20200525113959.11886-1-s.nawrocki@samsung.com> References: <20200525113959.11886-1-s.nawrocki@samsung.com> Message-ID: <20200525113959.11886-5-s.nawrocki@samsung.com> From: Marek Szyprowski Remove the overlap between DRAM and device's IO area. Signed-off-by: Marek Szyprowski Signed-off-by: Sylwester Nawrocki Reviewed-by: Nicolas Saenz Julienne --- Changes since v1: - none. --- arch/arm/mach-bcm283x/init.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/mach-bcm283x/init.c b/arch/arm/mach-bcm283x/init.c index 9966d6c..4295356 100644 --- a/arch/arm/mach-bcm283x/init.c +++ b/arch/arm/mach-bcm283x/init.c @@ -38,7 +38,7 @@ static struct mm_region bcm2711_mem_map[] = { { .virt = 0x00000000UL, .phys = 0x00000000UL, - .size = 0xfe000000UL, + .size = 0xfc000000UL, .attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) | PTE_BLOCK_INNER_SHARE }, { From patchwork Mon May 25 11:39:55 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: "Sylwester Nawrocki/Kernel \\\(PLT\\\) /SRPOL/Staff Engineer/Samsung Electronics" X-Patchwork-Id: 246505 List-Id: U-Boot discussion From: s.nawrocki at samsung.com (Sylwester Nawrocki) Date: Mon, 25 May 2020 13:39:55 +0200 Subject: [PATCH v4 5/9] rpi4: add a mapping for the PCIe XHCI controller MMIO registers (ARM 64bit) In-Reply-To: <20200525113959.11886-1-s.nawrocki@samsung.com> References: <20200525113959.11886-1-s.nawrocki@samsung.com> Message-ID: <20200525113959.11886-6-s.nawrocki@samsung.com> From: Marek Szyprowski Create a non-cacheable mapping for the 0x600000000 physical memory region, where MMIO registers for the PCIe XHCI controller are instantiated by the PCIe bridge. Signed-off-by: Marek Szyprowski Signed-off-by: Sylwester Nawrocki Reviewed-by: Nicolas Saenz Julienne --- Changes since v3: - none. Changes since v2: - fixed typo MAX_MAP_MAX_ENTRIES -> MEM_MAP_MAX_ENTRIES Changes since v1: - none. --- arch/arm/mach-bcm283x/init.c | 18 +++++++++++++++--- 1 file changed, 15 insertions(+), 3 deletions(-) diff --git a/arch/arm/mach-bcm283x/init.c b/arch/arm/mach-bcm283x/init.c index 4295356..9f5bca3 100644 --- a/arch/arm/mach-bcm283x/init.c +++ b/arch/arm/mach-bcm283x/init.c @@ -11,10 +11,15 @@ #include #include +#define BCM2711_RPI4_PCIE_XHCI_MMIO_PHYS 0x600000000UL +#define BCM2711_RPI4_PCIE_XHCI_MMIO_SIZE 0x800000UL + #ifdef CONFIG_ARM64 #include -static struct mm_region bcm283x_mem_map[] = { +#define MEM_MAP_MAX_ENTRIES (4) + +static struct mm_region bcm283x_mem_map[MEM_MAP_MAX_ENTRIES] = { { .virt = 0x00000000UL, .phys = 0x00000000UL, @@ -34,7 +39,7 @@ static struct mm_region bcm283x_mem_map[] = { } }; -static struct mm_region bcm2711_mem_map[] = { +static struct mm_region bcm2711_mem_map[MEM_MAP_MAX_ENTRIES] = { { .virt = 0x00000000UL, .phys = 0x00000000UL, @@ -49,6 +54,13 @@ static struct mm_region bcm2711_mem_map[] = { PTE_BLOCK_NON_SHARE | PTE_BLOCK_PXN | PTE_BLOCK_UXN }, { + .virt = BCM2711_RPI4_PCIE_XHCI_MMIO_PHYS, + .phys = BCM2711_RPI4_PCIE_XHCI_MMIO_PHYS, + .size = BCM2711_RPI4_PCIE_XHCI_MMIO_SIZE, + .attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) | + PTE_BLOCK_NON_SHARE | + PTE_BLOCK_PXN | PTE_BLOCK_UXN + }, { /* List terminator */ 0, } @@ -71,7 +83,7 @@ static void _rpi_update_mem_map(struct mm_region *pd) { int i; - for (i = 0; i < 2; i++) { + for (i = 0; i < MEM_MAP_MAX_ENTRIES; i++) { mem_map[i].virt = pd[i].virt; mem_map[i].phys = pd[i].phys; mem_map[i].size = pd[i].size; From patchwork Mon May 25 11:39:56 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: "Sylwester Nawrocki/Kernel \\\(PLT\\\) /SRPOL/Staff Engineer/Samsung Electronics" X-Patchwork-Id: 246508 List-Id: U-Boot discussion From: s.nawrocki at samsung.com (Sylwester Nawrocki) Date: Mon, 25 May 2020 13:39:56 +0200 Subject: [PATCH v4 6/9] linux/bitfield.h: Add primitives for manipulating bitfields both in host- and fixed-endian In-Reply-To: <20200525113959.11886-1-s.nawrocki@samsung.com> References: <20200525113959.11886-1-s.nawrocki@samsung.com> Message-ID: <20200525113959.11886-7-s.nawrocki@samsung.com> From: Nicolas Saenz Julienne Imports Al Viro's original Linux commit 00b0c9b82663a, which contains an in depth explanation and two fixes from Johannes Berg: e7d4a95da86e0 "bitfield: fix *_encode_bits()", 37a3862e12382 "bitfield: add u8 helpers". Signed-off-by: Nicolas Saenz Julienne [s.nawrocki: added empty lines between functions and macros] Signed-off-by: Sylwester Nawrocki --- Changes since v3: - none. Changes since v2: - added some more missing whitespaces as pointed out by checkpatch.pl. Changes since v1: - added empty lines between functions and macros. Changes since RFC: - new patch. --- include/linux/bitfield.h | 52 ++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 52 insertions(+) diff --git a/include/linux/bitfield.h b/include/linux/bitfield.h index 8b9d6ff..7ad8b08 100644 --- a/include/linux/bitfield.h +++ b/include/linux/bitfield.h @@ -103,4 +103,56 @@ (typeof(_mask))(((_reg) & (_mask)) >> __bf_shf(_mask)); \ }) +extern void __compiletime_error("value doesn't fit into mask") +__field_overflow(void); +extern void __compiletime_error("bad bitfield mask") +__bad_mask(void); + +static __always_inline u64 field_multiplier(u64 field) +{ + if ((field | (field - 1)) & ((field | (field - 1)) + 1)) + __bad_mask(); + return field & -field; +} + +static __always_inline u64 field_mask(u64 field) +{ + return field / field_multiplier(field); +} + +#define ____MAKE_OP(type, base, to, from) \ +static __always_inline __##type type##_encode_bits(base v, base field) \ +{ \ + if (__builtin_constant_p(v) && (v & ~field_mask(field))) \ + __field_overflow(); \ + return to((v & field_mask(field)) * field_multiplier(field)); \ +} \ +static __always_inline __##type type##_replace_bits(__##type old, \ + base val, base field) \ +{ \ + return (old & ~to(field)) | type##_encode_bits(val, field); \ +} \ +static __always_inline void type##p_replace_bits(__##type * p, \ + base val, base field) \ +{ \ + *p = (*p & ~to(field)) | type##_encode_bits(val, field); \ +} \ +static __always_inline base type##_get_bits(__##type v, base field) \ +{ \ + return (from(v) & field) / field_multiplier(field); \ +} + +#define __MAKE_OP(size) \ + ____MAKE_OP(le##size, u##size, cpu_to_le##size, le##size##_to_cpu) \ + ____MAKE_OP(be##size, u##size, cpu_to_be##size, be##size##_to_cpu) \ + ____MAKE_OP(u##size, u##size, ,) + +____MAKE_OP(u8, u8, ,) +__MAKE_OP(16) +__MAKE_OP(32) +__MAKE_OP(64) + +#undef __MAKE_OP +#undef ____MAKE_OP + #endif From patchwork Mon May 25 11:39:57 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: "Sylwester Nawrocki/Kernel \\\(PLT\\\) /SRPOL/Staff Engineer/Samsung Electronics" X-Patchwork-Id: 246506 List-Id: U-Boot discussion From: s.nawrocki at samsung.com (Sylwester Nawrocki) Date: Mon, 25 May 2020 13:39:57 +0200 Subject: [PATCH v4 7/9] pci: Add some PCI Express capability register offset definitions In-Reply-To: <20200525113959.11886-1-s.nawrocki@samsung.com> References: <20200525113959.11886-1-s.nawrocki@samsung.com> Message-ID: <20200525113959.11886-8-s.nawrocki@samsung.com> Add PCI Express capability definitions required by the Broadcom STB PCIe controller driver. Signed-off-by: Sylwester Nawrocki Reviewed-by: Bin Meng Reviewed-by: Nicolas Saenz Julienne --- Changes since v3: - none. Changes since v2: - added Current Link Speed defines. Changes since v1: - none. Changes since RFC: - ensure the entries are added in order, sorted by ascending address values. --- include/pci.h | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/include/pci.h b/include/pci.h index dfdbb32..ff5f620 100644 --- a/include/pci.h +++ b/include/pci.h @@ -479,11 +479,20 @@ #define PCI_EXP_DEVCTL 8 /* Device Control */ #define PCI_EXP_DEVCTL_BCR_FLR 0x8000 /* Bridge Configuration Retry / FLR */ #define PCI_EXP_LNKCAP 12 /* Link Capabilities */ +#define PCI_EXP_LNKCAP_SLS 0x0000000f /* Supported Link Speeds */ +#define PCI_EXP_LNKCAP_MLW 0x000003f0 /* Maximum Link Width */ #define PCI_EXP_LNKCAP_DLLLARC 0x00100000 /* Data Link Layer Link Active Reporting Capable */ #define PCI_EXP_LNKSTA 18 /* Link Status */ +#define PCI_EXP_LNKSTA_CLS 0x000f /* Current Link Speed */ +#define PCI_EXP_LNKSTA_CLS_2_5GB 0x0001 /* Current Link Speed 2.5GT/s */ +#define PCI_EXP_LNKSTA_CLS_5_0GB 0x0002 /* Current Link Speed 5.0GT/s */ +#define PCI_EXP_LNKSTA_CLS_8_0GB 0x0003 /* Current Link Speed 8.0GT/s */ +#define PCI_EXP_LNKSTA_NLW 0x03f0 /* Negotiated Link Width */ +#define PCI_EXP_LNKSTA_NLW_SHIFT 4 /* start of NLW mask in link status */ #define PCI_EXP_LNKSTA_DLLLA 0x2000 /* Data Link Layer Link Active */ #define PCI_EXP_SLTCAP 20 /* Slot Capabilities */ #define PCI_EXP_SLTCAP_PSN 0xfff80000 /* Physical Slot Number */ +#define PCI_EXP_LNKCTL2 48 /* Link Control 2 */ /* Include the ID list */ From patchwork Mon May 25 11:39:58 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: "Sylwester Nawrocki/Kernel \\\(PLT\\\) /SRPOL/Staff Engineer/Samsung Electronics" X-Patchwork-Id: 246509 List-Id: U-Boot discussion From: s.nawrocki at samsung.com (Sylwester Nawrocki) Date: Mon, 25 May 2020 13:39:58 +0200 Subject: [PATCH v4 8/9] pci: Add driver for Broadcom BCM2711 SoC PCIe controller In-Reply-To: <20200525113959.11886-1-s.nawrocki@samsung.com> References: <20200525113959.11886-1-s.nawrocki@samsung.com> Message-ID: <20200525113959.11886-9-s.nawrocki@samsung.com> This patch adds basic driver PCI Express controller found on Broadcom set-top-box SoCs, e.g. BCM2711. The code is based on Linux upstream driver (pcie-brcmstb.c) with MSI handling removed. The inbound access memory region is not currently parsed from dma-ranges DT property and a fixed 3GB region is used. The patch has been tested on RPI4 board, i.e. on BCM2711 SoC with VL805 USB Host Controller. Signed-off-by: Nicolas Saenz Julienne Signed-off-by: Sylwester Nawrocki --- Changes since v3: - none. Changes since v2 (mostly addressing Simon's review comments): - removed MDO_RD_DONE, MDIO_WT_DONE macro definitions, - updated the Kconfig entry help text, - reordered #include entries to match the coding style, - s/udev/dev, - s/ENODEV/EINVAL in brcm_pcie_probe() and brcm_pcie_config_address() functions, - Simplified brcm_pcie_mdio_{read, write} functions (readl_poll_timeout), - shortened register bit fields macro definitions, - dropped brcm_pcie_perst_set() and brcm_pcie_bridge_sw_init_set() function in favour of direct clrbits_le32/setbits_le32 calls, - use setbits_le32/clrbits_le32/clrsetbits_le32 instead of readl(), u32p_replace_bits(), writel() sequence - simplified brcm_pcie_config_address(), brcm_pcie_set_gen() functions, - changed reset pulse delay to 100 us, - Replaced FIELD_GET() with open coded bitwise operations, - brcm_cpie_cfg_index() function merged into brcm_pcie_config_address(), - use standard PCI PCI_EXP_LNKSTA_CLS_* link speed defines - added kernel-doc function comments. Changes since v1: - fixed argument in brcm_pcie_set_ssc() function call, - changed rc_bar2_size assignment to value 0xC0000000, as in upstream devicetree. Changes since RFC: - reworked to align with current Linux mainline version and u-boot driver by Nicolas Saenz Julienne. --- drivers/pci/Kconfig | 9 + drivers/pci/Makefile | 1 + drivers/pci/pcie_brcmstb.c | 623 +++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 633 insertions(+) create mode 100644 drivers/pci/pcie_brcmstb.c diff --git a/drivers/pci/Kconfig b/drivers/pci/Kconfig index 437cd9a..543bd46 100644 --- a/drivers/pci/Kconfig +++ b/drivers/pci/Kconfig @@ -197,4 +197,13 @@ config PCIE_MEDIATEK Say Y here if you want to enable Gen2 PCIe controller, which could be found on MT7623 SoC family. +config PCI_BRCMSTB + bool "Broadcom STB PCIe controller" + depends on DM_PCI + depends on ARCH_BCM283X + help + Say Y here if you want to enable support for PCIe controller + on Broadcom set-top-box (STB) SoCs. + This driver currently supports only BCM2711 SoC and RC mode + of the controller. endif diff --git a/drivers/pci/Makefile b/drivers/pci/Makefile index c051ecc..3e53b1f 100644 --- a/drivers/pci/Makefile +++ b/drivers/pci/Makefile @@ -43,3 +43,4 @@ obj-$(CONFIG_PCI_PHYTIUM) += pcie_phytium.o obj-$(CONFIG_PCIE_INTEL_FPGA) += pcie_intel_fpga.o obj-$(CONFIG_PCI_KEYSTONE) += pcie_dw_ti.o obj-$(CONFIG_PCIE_MEDIATEK) += pcie_mediatek.o +obj-$(CONFIG_PCI_BRCMSTB) += pcie_brcmstb.o diff --git a/drivers/pci/pcie_brcmstb.c b/drivers/pci/pcie_brcmstb.c new file mode 100644 index 0000000..dade79e --- /dev/null +++ b/drivers/pci/pcie_brcmstb.c @@ -0,0 +1,623 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Broadcom STB PCIe controller driver + * + * Copyright (C) 2020 Samsung Electronics Co., Ltd. + * + * Based on upstream Linux kernel driver: + * drivers/pci/controller/pcie-brcmstb.c + * Copyright (C) 2009 - 2017 Broadcom + * + * Based driver by Nicolas Saenz Julienne + * Copyright (C) 2020 Nicolas Saenz Julienne + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* Offset of the mandatory PCIe capability config registers */ +#define BRCM_PCIE_CAP_REGS 0x00ac + +/* The PCIe controller register offsets */ +#define PCIE_RC_CFG_VENDOR_SPECIFIC_REG1 0x0188 +#define VENDOR_SPECIFIC_REG1_ENDIAN_MODE_BAR2_MASK 0xc +#define VENDOR_SPECIFIC_REG1_LITTLE_ENDIAN 0x0 + +#define PCIE_RC_CFG_PRIV1_ID_VAL3 0x043c +#define CFG_PRIV1_ID_VAL3_CLASS_CODE_MASK 0xffffff + +#define PCIE_RC_DL_MDIO_ADDR 0x1100 +#define PCIE_RC_DL_MDIO_WR_DATA 0x1104 +#define PCIE_RC_DL_MDIO_RD_DATA 0x1108 + +#define PCIE_MISC_MISC_CTRL 0x4008 +#define MISC_CTRL_SCB_ACCESS_EN_MASK 0x1000 +#define MISC_CTRL_CFG_READ_UR_MODE_MASK 0x2000 +#define MISC_CTRL_MAX_BURST_SIZE_MASK 0x300000 +#define MISC_CTRL_MAX_BURST_SIZE_128 0x0 +#define MISC_CTRL_SCB0_SIZE_MASK 0xf8000000 + +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LO 0x400c +#define PCIE_MEM_WIN0_LO(win) \ + PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LO + ((win) * 4) + +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_HI 0x4010 +#define PCIE_MEM_WIN0_HI(win) \ + PCIE_MISC_CPU_2_PCIE_MEM_WIN0_HI + ((win) * 4) + +#define PCIE_MISC_RC_BAR1_CONFIG_LO 0x402c +#define RC_BAR1_CONFIG_LO_SIZE_MASK 0x1f + +#define PCIE_MISC_RC_BAR2_CONFIG_LO 0x4034 +#define RC_BAR2_CONFIG_LO_SIZE_MASK 0x1f +#define PCIE_MISC_RC_BAR2_CONFIG_HI 0x4038 + +#define PCIE_MISC_RC_BAR3_CONFIG_LO 0x403c +#define RC_BAR3_CONFIG_LO_SIZE_MASK 0x1f + +#define PCIE_MISC_PCIE_STATUS 0x4068 +#define STATUS_PCIE_PORT_MASK 0x80 +#define STATUS_PCIE_PORT_SHIFT 7 +#define STATUS_PCIE_DL_ACTIVE_MASK 0x20 +#define STATUS_PCIE_DL_ACTIVE_SHIFT 5 +#define STATUS_PCIE_PHYLINKUP_MASK 0x10 +#define STATUS_PCIE_PHYLINKUP_SHIFT 4 + +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT 0x4070 +#define MEM_WIN0_BASE_LIMIT_LIMIT_MASK 0xfff00000 +#define MEM_WIN0_BASE_LIMIT_BASE_MASK 0xfff0 +#define MEM_WIN0_BASE_LIMIT_BASE_HI_SHIFT 12 +#define PCIE_MEM_WIN0_BASE_LIMIT(win) \ + PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT + ((win) * 4) + +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_HI 0x4080 +#define MEM_WIN0_BASE_HI_BASE_MASK 0xff +#define PCIE_MEM_WIN0_BASE_HI(win) \ + PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_HI + ((win) * 8) + +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LIMIT_HI 0x4084 +#define PCIE_MEM_WIN0_LIMIT_HI_LIMIT_MASK 0xff +#define PCIE_MEM_WIN0_LIMIT_HI(win) \ + PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LIMIT_HI + ((win) * 8) + +#define PCIE_MISC_HARD_PCIE_HARD_DEBUG 0x4204 +#define PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK 0x2 +#define PCIE_HARD_DEBUG_SERDES_IDDQ_MASK 0x08000000 + +#define PCIE_MSI_INTR2_CLR 0x4508 +#define PCIE_MSI_INTR2_MASK_SET 0x4510 + +#define PCIE_EXT_CFG_DATA 0x8000 + +#define PCIE_EXT_CFG_INDEX 0x9000 +#define PCIE_EXT_BUSNUM_SHIFT 20 +#define PCIE_EXT_SLOT_SHIFT 15 +#define PCIE_EXT_FUNC_SHIFT 12 + +#define PCIE_RGR1_SW_INIT_1 0x9210 +#define RGR1_SW_INIT_1_PERST_MASK 0x1 +#define RGR1_SW_INIT_1_INIT_MASK 0x2 + +/* PCIe parameters */ +#define BRCM_NUM_PCIE_OUT_WINS 4 + +/* MDIO registers */ +#define MDIO_PORT0 0x0 +#define MDIO_DATA_MASK 0x7fffffff +#define MDIO_DATA_SHIFT 0 +#define MDIO_PORT_MASK 0xf0000 +#define MDIO_PORT_SHIFT 16 +#define MDIO_REGAD_MASK 0xffff +#define MDIO_REGAD_SHIFT 0 +#define MDIO_CMD_MASK 0xfff00000 +#define MDIO_CMD_SHIFT 20 +#define MDIO_CMD_READ 0x1 +#define MDIO_CMD_WRITE 0x0 +#define MDIO_DATA_DONE_MASK 0x80000000 +#define SSC_REGS_ADDR 0x1100 +#define SET_ADDR_OFFSET 0x1f +#define SSC_CNTL_OFFSET 0x2 +#define SSC_CNTL_OVRD_EN_MASK 0x8000 +#define SSC_CNTL_OVRD_VAL_MASK 0x4000 +#define SSC_STATUS_OFFSET 0x1 +#define SSC_STATUS_SSC_MASK 0x400 +#define SSC_STATUS_SSC_SHIFT 10 +#define SSC_STATUS_PLL_LOCK_MASK 0x800 +#define SSC_STATUS_PLL_LOCK_SHIFT 11 + +/** + * struct brcm_pcie - the PCIe controller state + * @base: Base address of memory mapped IO registers of the controller + * @gen: Non-zero value indicates limitation of the PCIe controller operation + * to a specific generation (1, 2 or 3) + * @ssc: true indicates active Spread Spectrum Clocking operation + */ +struct brcm_pcie { + void __iomem *base; + + int gen; + bool ssc; +}; + +/** + * brcm_pcie_encode_ibar_size() - Encode the inbound "BAR" region size + * @size: The inbound region size + * + * This function converts size of the inbound "BAR" region to the non-linear + * values of the PCIE_MISC_RC_BAR[123]_CONFIG_LO register SIZE field. + * + * Return: The encoded inbound region size + */ +static int brcm_pcie_encode_ibar_size(u64 size) +{ + int log2_in = ilog2(size); + + if (log2_in >= 12 && log2_in <= 15) + /* Covers 4KB to 32KB (inclusive) */ + return (log2_in - 12) + 0x1c; + else if (log2_in >= 16 && log2_in <= 37) + /* Covers 64KB to 32GB, (inclusive) */ + return log2_in - 15; + + /* Something is awry so disable */ + return 0; +} + +/** + * brcm_pcie_rc_mode() - Check if PCIe controller is in RC mode + * @pcie: Pointer to the PCIe controller state + * + * The controller is capable of serving in both RC and EP roles. + * + * Return: true for RC mode, false for EP mode. + */ +static bool brcm_pcie_rc_mode(struct brcm_pcie *pcie) +{ + u32 val; + + val = readl(pcie->base + PCIE_MISC_PCIE_STATUS); + + return (val & STATUS_PCIE_PORT_MASK) >> STATUS_PCIE_PORT_SHIFT; +} + +/** + * brcm_pcie_link_up() - Check whether the PCIe link is up + * @pcie: Pointer to the PCIe controller state + * + * Return: true if the link is up, false otherwise. + */ +static bool brcm_pcie_link_up(struct brcm_pcie *pcie) +{ + u32 val, dla, plu; + + val = readl(pcie->base + PCIE_MISC_PCIE_STATUS); + dla = (val & STATUS_PCIE_DL_ACTIVE_MASK) >> STATUS_PCIE_DL_ACTIVE_SHIFT; + plu = (val & STATUS_PCIE_PHYLINKUP_MASK) >> STATUS_PCIE_PHYLINKUP_SHIFT; + + return dla && plu; +} + +static int brcm_pcie_config_address(const struct udevice *dev, pci_dev_t bdf, + uint offset, void **paddress) +{ + struct brcm_pcie *pcie = dev_get_priv(dev); + unsigned int pci_bus = PCI_BUS(bdf); + unsigned int pci_dev = PCI_DEV(bdf); + unsigned int pci_func = PCI_FUNC(bdf); + int idx; + + /* + * Busses 0 (host PCIe bridge) and 1 (its immediate child) + * are limited to a single device each + */ + if (pci_bus < 2 && pci_dev > 0) + return -EINVAL; + + /* Accesses to the RC go right to the RC registers */ + if (pci_bus == 0) { + *paddress = pcie->base + offset; + return 0; + } + + /* For devices, write to the config space index register */ + idx = (pci_bus << PCIE_EXT_BUSNUM_SHIFT) + | (pci_dev << PCIE_EXT_SLOT_SHIFT) + | (pci_func << PCIE_EXT_FUNC_SHIFT); + + writel(idx, pcie->base + PCIE_EXT_CFG_INDEX); + *paddress = pcie->base + PCIE_EXT_CFG_DATA + offset; + + return 0; +} + +static int brcm_pcie_read_config(const struct udevice *bus, pci_dev_t bdf, + uint offset, ulong *valuep, + enum pci_size_t size) +{ + return pci_generic_mmap_read_config(bus, brcm_pcie_config_address, + bdf, offset, valuep, size); +} + +static int brcm_pcie_write_config(struct udevice *bus, pci_dev_t bdf, + uint offset, ulong value, + enum pci_size_t size) +{ + return pci_generic_mmap_write_config(bus, brcm_pcie_config_address, + bdf, offset, value, size); +} + +static const char *link_speed_to_str(unsigned int cls) +{ + switch (cls) { + case PCI_EXP_LNKSTA_CLS_2_5GB: return "2.5"; + case PCI_EXP_LNKSTA_CLS_5_0GB: return "5.0"; + case PCI_EXP_LNKSTA_CLS_8_0GB: return "8.0"; + default: + break; + } + + return "??"; +} + +static u32 brcm_pcie_mdio_form_pkt(unsigned int port, unsigned int regad, + unsigned int cmd) +{ + u32 pkt; + + pkt = (port << MDIO_PORT_SHIFT) & MDIO_PORT_MASK; + pkt |= (regad << MDIO_REGAD_SHIFT) & MDIO_REGAD_MASK; + pkt |= (cmd << MDIO_CMD_SHIFT) & MDIO_CMD_MASK; + + return pkt; +} + +/** + * brcm_pcie_mdio_read() - Perform a register read on the internal MDIO bus + * @base: Pointer to the PCIe controller IO registers + * @port: The MDIO port number + * @regad: The register address + * @val: A pointer at which to store the read value + * + * Return: 0 on success and register value in @val, negative error value + * on failure. + */ +static int brcm_pcie_mdio_read(void __iomem *base, unsigned int port, + unsigned int regad, u32 *val) +{ + u32 data, addr; + int ret; + + addr = brcm_pcie_mdio_form_pkt(port, regad, MDIO_CMD_READ); + writel(addr, base + PCIE_RC_DL_MDIO_ADDR); + readl(base + PCIE_RC_DL_MDIO_ADDR); + + ret = readl_poll_timeout(base + PCIE_RC_DL_MDIO_RD_DATA, data, + (data & MDIO_DATA_DONE_MASK), 100); + + *val = data & MDIO_DATA_MASK; + + return ret; +} + +/** + * brcm_pcie_mdio_write() - Perform a register write on the internal MDIO bus + * @base: Pointer to the PCIe controller IO registers + * @port: The MDIO port number + * @regad: Address of the register + * @wrdata: The value to write + * + * Return: 0 on success, negative error value on failure. + */ +static int brcm_pcie_mdio_write(void __iomem *base, unsigned int port, + unsigned int regad, u16 wrdata) +{ + u32 data, addr; + + addr = brcm_pcie_mdio_form_pkt(port, regad, MDIO_CMD_WRITE); + writel(addr, base + PCIE_RC_DL_MDIO_ADDR); + readl(base + PCIE_RC_DL_MDIO_ADDR); + writel(MDIO_DATA_DONE_MASK | wrdata, base + PCIE_RC_DL_MDIO_WR_DATA); + + return readl_poll_timeout(base + PCIE_RC_DL_MDIO_WR_DATA, data, + !(data & MDIO_DATA_DONE_MASK), 100); +} + +/** + * brcm_pcie_set_ssc() - Configure the controller for Spread Spectrum Clocking + * @base: pointer to the PCIe controller IO registers + * + * Return: 0 on success, negative error value on failure. + */ +static int brcm_pcie_set_ssc(void __iomem *base) +{ + int pll, ssc; + int ret; + u32 tmp; + + ret = brcm_pcie_mdio_write(base, MDIO_PORT0, SET_ADDR_OFFSET, + SSC_REGS_ADDR); + if (ret < 0) + return ret; + + ret = brcm_pcie_mdio_read(base, MDIO_PORT0, SSC_CNTL_OFFSET, &tmp); + if (ret < 0) + return ret; + + tmp |= (SSC_CNTL_OVRD_EN_MASK | SSC_CNTL_OVRD_VAL_MASK); + + ret = brcm_pcie_mdio_write(base, MDIO_PORT0, SSC_CNTL_OFFSET, tmp); + if (ret < 0) + return ret; + + udelay(1000); + ret = brcm_pcie_mdio_read(base, MDIO_PORT0, SSC_STATUS_OFFSET, &tmp); + if (ret < 0) + return ret; + + ssc = (tmp & SSC_STATUS_SSC_MASK) >> SSC_STATUS_SSC_SHIFT; + pll = (tmp & SSC_STATUS_PLL_LOCK_MASK) >> SSC_STATUS_PLL_LOCK_SHIFT; + + return ssc && pll ? 0 : -EIO; +} + +/** + * brcm_pcie_set_gen() - Limits operation to a specific generation (1, 2 or 3) + * @pcie: pointer to the PCIe controller state + * @gen: PCIe generation to limit the controller's operation to + */ +static void brcm_pcie_set_gen(struct brcm_pcie *pcie, unsigned int gen) +{ + void __iomem *cap_base = pcie->base + BRCM_PCIE_CAP_REGS; + + u16 lnkctl2 = readw(cap_base + PCI_EXP_LNKCTL2); + u32 lnkcap = readl(cap_base + PCI_EXP_LNKCAP); + + lnkcap = (lnkcap & ~PCI_EXP_LNKCAP_SLS) | gen; + writel(lnkcap, cap_base + PCI_EXP_LNKCAP); + + lnkctl2 = (lnkctl2 & ~0xf) | gen; + writew(lnkctl2, cap_base + PCI_EXP_LNKCTL2); +} + +static void brcm_pcie_set_outbound_win(struct brcm_pcie *pcie, + unsigned int win, u64 phys_addr, + u64 pcie_addr, u64 size) +{ + void __iomem *base = pcie->base; + u32 phys_addr_mb_high, limit_addr_mb_high; + phys_addr_t phys_addr_mb, limit_addr_mb; + int high_addr_shift; + u32 tmp; + + /* Set the base of the pcie_addr window */ + writel(lower_32_bits(pcie_addr), base + PCIE_MEM_WIN0_LO(win)); + writel(upper_32_bits(pcie_addr), base + PCIE_MEM_WIN0_HI(win)); + + /* Write the addr base & limit lower bits (in MBs) */ + phys_addr_mb = phys_addr / SZ_1M; + limit_addr_mb = (phys_addr + size - 1) / SZ_1M; + + tmp = readl(base + PCIE_MEM_WIN0_BASE_LIMIT(win)); + u32p_replace_bits(&tmp, phys_addr_mb, + MEM_WIN0_BASE_LIMIT_BASE_MASK); + u32p_replace_bits(&tmp, limit_addr_mb, + MEM_WIN0_BASE_LIMIT_LIMIT_MASK); + writel(tmp, base + PCIE_MEM_WIN0_BASE_LIMIT(win)); + + /* Write the cpu & limit addr upper bits */ + high_addr_shift = MEM_WIN0_BASE_LIMIT_BASE_HI_SHIFT; + phys_addr_mb_high = phys_addr_mb >> high_addr_shift; + tmp = readl(base + PCIE_MEM_WIN0_BASE_HI(win)); + u32p_replace_bits(&tmp, phys_addr_mb_high, + MEM_WIN0_BASE_HI_BASE_MASK); + writel(tmp, base + PCIE_MEM_WIN0_BASE_HI(win)); + + limit_addr_mb_high = limit_addr_mb >> high_addr_shift; + tmp = readl(base + PCIE_MEM_WIN0_LIMIT_HI(win)); + u32p_replace_bits(&tmp, limit_addr_mb_high, + PCIE_MEM_WIN0_LIMIT_HI_LIMIT_MASK); + writel(tmp, base + PCIE_MEM_WIN0_LIMIT_HI(win)); +} + +static int brcm_pcie_probe(struct udevice *dev) +{ + struct udevice *ctlr = pci_get_controller(dev); + struct pci_controller *hose = dev_get_uclass_priv(ctlr); + struct brcm_pcie *pcie = dev_get_priv(dev); + void __iomem *base = pcie->base; + bool ssc_good = false; + int num_out_wins = 0; + u64 rc_bar2_offset, rc_bar2_size; + unsigned int scb_size_val; + int i, ret; + u16 nlw, cls, lnksta; + u32 tmp; + + /* + * Reset the bridge, assert the fundamental reset. Note for some SoCs, + * e.g. BCM7278, the fundamental reset should not be asserted here. + * This will need to be changed when support for other SoCs is added. + */ + setbits_le32(base + PCIE_RGR1_SW_INIT_1, + RGR1_SW_INIT_1_INIT_MASK | RGR1_SW_INIT_1_PERST_MASK); + /* + * The delay is a safety precaution to preclude the reset signal + * from looking like a glitch. + */ + udelay(100); + + /* Take the bridge out of reset */ + clrbits_le32(base + PCIE_RGR1_SW_INIT_1, RGR1_SW_INIT_1_INIT_MASK); + + clrbits_le32(base + PCIE_MISC_HARD_PCIE_HARD_DEBUG, + PCIE_HARD_DEBUG_SERDES_IDDQ_MASK); + + /* Wait for SerDes to be stable */ + udelay(100); + + /* Set SCB_MAX_BURST_SIZE, CFG_READ_UR_MODE, SCB_ACCESS_EN */ + clrsetbits_le32(base + PCIE_MISC_MISC_CTRL, + MISC_CTRL_MAX_BURST_SIZE_MASK, + MISC_CTRL_SCB_ACCESS_EN_MASK | + MISC_CTRL_CFG_READ_UR_MODE_MASK | + MISC_CTRL_MAX_BURST_SIZE_128); + /* + * TODO: When support for other SoCs than BCM2711 is added we may + * need to use the base address and size(s) provided in the dma-ranges + * property. + */ + rc_bar2_offset = 0; + rc_bar2_size = 0xc0000000; + + tmp = lower_32_bits(rc_bar2_offset); + u32p_replace_bits(&tmp, brcm_pcie_encode_ibar_size(rc_bar2_size), + RC_BAR2_CONFIG_LO_SIZE_MASK); + writel(tmp, base + PCIE_MISC_RC_BAR2_CONFIG_LO); + writel(upper_32_bits(rc_bar2_offset), + base + PCIE_MISC_RC_BAR2_CONFIG_HI); + + scb_size_val = rc_bar2_size ? + ilog2(rc_bar2_size) - 15 : 0xf; /* 0xf is 1GB */ + + tmp = readl(base + PCIE_MISC_MISC_CTRL); + u32p_replace_bits(&tmp, scb_size_val, + MISC_CTRL_SCB0_SIZE_MASK); + writel(tmp, base + PCIE_MISC_MISC_CTRL); + + /* Disable the PCIe->GISB memory window (RC_BAR1) */ + clrbits_le32(base + PCIE_MISC_RC_BAR1_CONFIG_LO, + RC_BAR1_CONFIG_LO_SIZE_MASK); + + /* Disable the PCIe->SCB memory window (RC_BAR3) */ + clrbits_le32(base + PCIE_MISC_RC_BAR3_CONFIG_LO, + RC_BAR3_CONFIG_LO_SIZE_MASK); + + /* Mask all interrupts since we are not handling any yet */ + writel(0xffffffff, base + PCIE_MSI_INTR2_MASK_SET); + + /* Clear any interrupts we find on boot */ + writel(0xffffffff, base + PCIE_MSI_INTR2_CLR); + + if (pcie->gen) + brcm_pcie_set_gen(pcie, pcie->gen); + + /* Unassert the fundamental reset */ + clrbits_le32(pcie->base + PCIE_RGR1_SW_INIT_1, + RGR1_SW_INIT_1_PERST_MASK); + + /* Give the RC/EP time to wake up, before trying to configure RC. + * Intermittently check status for link-up, up to a total of 100ms. + */ + for (i = 0; i < 100 && !brcm_pcie_link_up(pcie); i += 5) + mdelay(5); + + if (!brcm_pcie_link_up(pcie)) { + printf("PCIe BRCM: link down\n"); + return -EINVAL; + } + + if (!brcm_pcie_rc_mode(pcie)) { + printf("PCIe misconfigured; is in EP mode\n"); + return -EINVAL; + } + + for (i = 0; i < hose->region_count; i++) { + struct pci_region *reg = &hose->regions[i]; + + if (reg->flags != PCI_REGION_MEM) + continue; + + if (num_out_wins >= BRCM_NUM_PCIE_OUT_WINS) + return -EINVAL; + + brcm_pcie_set_outbound_win(pcie, num_out_wins, reg->phys_start, + reg->bus_start, reg->size); + + num_out_wins++; + } + + /* + * For config space accesses on the RC, show the right class for + * a PCIe-PCIe bridge (the default setting is to be EP mode). + */ + clrsetbits_le32(base + PCIE_RC_CFG_PRIV1_ID_VAL3, + CFG_PRIV1_ID_VAL3_CLASS_CODE_MASK, 0x060400); + + if (pcie->ssc) { + ret = brcm_pcie_set_ssc(pcie->base); + if (!ret) + ssc_good = true; + else + printf("PCIe BRCM: failed attempt to enter SSC mode\n"); + } + + lnksta = readw(base + BRCM_PCIE_CAP_REGS + PCI_EXP_LNKSTA); + cls = lnksta & PCI_EXP_LNKSTA_CLS; + nlw = (lnksta & PCI_EXP_LNKSTA_NLW) >> PCI_EXP_LNKSTA_NLW_SHIFT; + + printf("PCIe BRCM: link up, %s Gbps x%u %s\n", link_speed_to_str(cls), + nlw, ssc_good ? "(SSC)" : "(!SSC)"); + + /* PCIe->SCB endian mode for BAR */ + clrsetbits_le32(base + PCIE_RC_CFG_VENDOR_SPECIFIC_REG1, + VENDOR_SPECIFIC_REG1_ENDIAN_MODE_BAR2_MASK, + VENDOR_SPECIFIC_REG1_LITTLE_ENDIAN); + /* + * Refclk from RC should be gated with CLKREQ# input when ASPM L0s,L1 + * is enabled => setting the CLKREQ_DEBUG_ENABLE field to 1. + */ + setbits_le32(base + PCIE_MISC_HARD_PCIE_HARD_DEBUG, + PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK); + + return 0; +} + +static int brcm_pcie_ofdata_to_platdata(struct udevice *dev) +{ + struct brcm_pcie *pcie = dev_get_priv(dev); + ofnode dn = dev_ofnode(dev); + u32 max_link_speed; + int ret; + + /* Get the controller base address */ + pcie->base = dev_read_addr_ptr(dev); + if (!pcie->base) + return -EINVAL; + + pcie->ssc = ofnode_read_bool(dn, "brcm,enable-ssc"); + + ret = ofnode_read_u32(dn, "max-link-speed", &max_link_speed); + if (ret < 0 || max_link_speed > 4) + pcie->gen = 0; + else + pcie->gen = max_link_speed; + + return 0; +} + +static const struct dm_pci_ops brcm_pcie_ops = { + .read_config = brcm_pcie_read_config, + .write_config = brcm_pcie_write_config, +}; + +static const struct udevice_id brcm_pcie_ids[] = { + { .compatible = "brcm,bcm2711-pcie" }, + { } +}; + +U_BOOT_DRIVER(pcie_brcm_base) = { + .name = "pcie_brcm", + .id = UCLASS_PCI, + .ops = &brcm_pcie_ops, + .of_match = brcm_pcie_ids, + .probe = brcm_pcie_probe, + .ofdata_to_platdata = brcm_pcie_ofdata_to_platdata, + .priv_auto_alloc_size = sizeof(struct brcm_pcie), +}; From patchwork Mon May 25 11:39:59 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: "Sylwester Nawrocki/Kernel \\\(PLT\\\) /SRPOL/Staff Engineer/Samsung Electronics" X-Patchwork-Id: 246507 List-Id: U-Boot discussion From: s.nawrocki at samsung.com (Sylwester Nawrocki) Date: Mon, 25 May 2020 13:39:59 +0200 Subject: [PATCH v4 9/9] configs: Enable support for the XHCI controller on RPI4 board (ARM 64-bit) In-Reply-To: <20200525113959.11886-1-s.nawrocki@samsung.com> References: <20200525113959.11886-1-s.nawrocki@samsung.com> Message-ID: <20200525113959.11886-10-s.nawrocki@samsung.com> From: Marek Szyprowski This requires enabling BRCMSTB PCIe and XHCI_PCI drivers as well as PCI and USB commands. To get it working one has to call the following commands: "pci enum; usb start;", thus such commands have been added to the default "preboot" environment variable. One has to update their environment if it is already configured to get this feature working out of the box. Signed-off-by: Marek Szyprowski Signed-off-by: Sylwester Nawrocki --- Changes since v3: - added missing rpi_4_defconfig changes Changes since v2: - rpi_4_32b_defconfig, rpi_4_defconfig changes moved to separate patch Changes since v1: - removed unneeded CONFIG_XHCI_64BIT_DWORD_ACCESS_ONLY entry. Changes since RFC: - none. --- configs/rpi_4_defconfig | 9 +++++++++ configs/rpi_arm64_defconfig | 8 +++++++- 2 files changed, 16 insertions(+), 1 deletion(-) diff --git a/configs/rpi_4_defconfig b/configs/rpi_4_defconfig index 6d148da..3f1a1b5 100644 --- a/configs/rpi_4_defconfig +++ b/configs/rpi_4_defconfig @@ -8,6 +8,8 @@ CONFIG_NR_DRAM_BANKS=2 CONFIG_DISTRO_DEFAULTS=y CONFIG_OF_BOARD_SETUP=y # CONFIG_ARCH_FIXUP_FDT_MEMORY is not set +CONFIG_USE_PREBOOT=y +CONFIG_PREBOOT="pci enum; usb start;" CONFIG_MISC_INIT_R=y # CONFIG_DISPLAY_CPUINFO is not set # CONFIG_DISPLAY_BOARDINFO is not set @@ -15,6 +17,8 @@ CONFIG_SYS_PROMPT="U-Boot> " CONFIG_CMD_DFU=y CONFIG_CMD_GPIO=y CONFIG_CMD_MMC=y +CONFIG_CMD_PCI=y +CONFIG_CMD_USB=y CONFIG_CMD_FS_UUID=y CONFIG_OF_BOARD=y CONFIG_ENV_FAT_INTERFACE="mmc" @@ -28,12 +32,17 @@ CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_BCM2835=y CONFIG_DM_ETH=y CONFIG_BCMGENET=y +CONFIG_PCI=y +CONFIG_DM_PCI=y +CONFIG_PCI_BRCMSTB=y CONFIG_PINCTRL=y # CONFIG_PINCTRL_GENERIC is not set # CONFIG_REQUIRE_SERIAL_CONSOLE is not set CONFIG_USB=y CONFIG_DM_USB=y CONFIG_DM_USB_GADGET=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_PCI=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="FSL" CONFIG_USB_GADGET_VENDOR_NUM=0x0525 diff --git a/configs/rpi_arm64_defconfig b/configs/rpi_arm64_defconfig index fea86be..f12d1e3 100644 --- a/configs/rpi_arm64_defconfig +++ b/configs/rpi_arm64_defconfig @@ -7,13 +7,14 @@ CONFIG_NR_DRAM_BANKS=2 CONFIG_DISTRO_DEFAULTS=y CONFIG_OF_BOARD_SETUP=y CONFIG_USE_PREBOOT=y -CONFIG_PREBOOT="usb start" +CONFIG_PREBOOT="pci enum; usb start;" CONFIG_MISC_INIT_R=y # CONFIG_DISPLAY_CPUINFO is not set # CONFIG_DISPLAY_BOARDINFO is not set CONFIG_SYS_PROMPT="U-Boot> " CONFIG_CMD_GPIO=y CONFIG_CMD_MMC=y +CONFIG_CMD_PCI=y CONFIG_CMD_USB=y CONFIG_CMD_FS_UUID=y CONFIG_OF_BOARD=y @@ -26,11 +27,16 @@ CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_BCM2835=y CONFIG_DM_ETH=y CONFIG_BCMGENET=y +CONFIG_PCI=y +CONFIG_DM_PCI=y +CONFIG_PCI_BRCMSTB=y CONFIG_PINCTRL=y # CONFIG_PINCTRL_GENERIC is not set # CONFIG_REQUIRE_SERIAL_CONSOLE is not set CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_PCI=y CONFIG_USB_DWC2=y CONFIG_USB_KEYBOARD=y CONFIG_USB_HOST_ETHER=y