From patchwork Mon Jan 20 12:20:06 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Baruch Siach X-Patchwork-Id: 239807 List-Id: U-Boot discussion From: baruch at tkos.co.il (Baruch Siach) Date: Mon, 20 Jan 2020 14:20:06 +0200 Subject: [PATCH v2 01/10] ddr: marvell: a38x: allow board specific clock out setup In-Reply-To: References: Message-ID: <0b7a38d599638c64e11d44151c8965b56db32ea8.1579522639.git.baruch@tkos.co.il> DDR clock out might be unrelated to the number of active chip-select. For example, the board might have two DDR components, but only one chip-select. The clk_enable mask allows the board to enable DDR clocks regardless of active chip-selects. Reviewed-by: Stefan Roese Signed-off-by: Baruch Siach --- drivers/ddr/marvell/a38x/ddr3_training.c | 10 ++++++++-- drivers/ddr/marvell/a38x/ddr_topology_def.h | 3 +++ 2 files changed, 11 insertions(+), 2 deletions(-) diff --git a/drivers/ddr/marvell/a38x/ddr3_training.c b/drivers/ddr/marvell/a38x/ddr3_training.c index c7be700d641f..9718f18c3024 100644 --- a/drivers/ddr/marvell/a38x/ddr3_training.c +++ b/drivers/ddr/marvell/a38x/ddr3_training.c @@ -280,8 +280,14 @@ int ddr3_tip_configure_cs(u32 dev_num, u32 if_id, u32 cs_num, u32 enable) { u32 data, addr_hi, data_high; u32 mem_index; + u32 clk_enable; struct mv_ddr_topology_map *tm = mv_ddr_topology_map_get(); + if (tm->clk_enable & (1 << cs_num)) + clk_enable = 1; + else + clk_enable = enable; + if (enable == 1) { data = (tm->interface_params[if_id].bus_width == MV_DDR_DEV_WIDTH_8BIT) ? 0 : 1; @@ -316,13 +322,13 @@ int ddr3_tip_configure_cs(u32 dev_num, u32 if_id, u32 cs_num, u32 enable) case 2: CHECK_STATUS(ddr3_tip_if_write (dev_num, ACCESS_TYPE_UNICAST, if_id, - DUNIT_CTRL_LOW_REG, (enable << (cs_num + 11)), + DUNIT_CTRL_LOW_REG, (clk_enable << (cs_num + 11)), 1 << (cs_num + 11))); break; case 3: CHECK_STATUS(ddr3_tip_if_write (dev_num, ACCESS_TYPE_UNICAST, if_id, - DUNIT_CTRL_LOW_REG, (enable << 15), 1 << 15)); + DUNIT_CTRL_LOW_REG, (clk_enable << 15), 1 << 15)); break; } diff --git a/drivers/ddr/marvell/a38x/ddr_topology_def.h b/drivers/ddr/marvell/a38x/ddr_topology_def.h index e6fe8a04289b..950f296ff984 100644 --- a/drivers/ddr/marvell/a38x/ddr_topology_def.h +++ b/drivers/ddr/marvell/a38x/ddr_topology_def.h @@ -124,6 +124,9 @@ struct mv_ddr_topology_map { /* electrical parameters */ unsigned int electrical_data[MV_DDR_EDATA_LAST]; + + /* Clock enable mask */ + u32 clk_enable; }; enum mv_ddr_iface_mode { From patchwork Mon Jan 20 12:20:07 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Baruch Siach X-Patchwork-Id: 239810 List-Id: U-Boot discussion From: baruch at tkos.co.il (Baruch Siach) Date: Mon, 20 Jan 2020 14:20:07 +0200 Subject: [PATCH v2 02/10] arm: mvebu: clearfog: enable both DDR clocks In-Reply-To: References: Message-ID: Enabled both DDR clock signals to support Clearfog variants (currently, Clearfog GTR) that need both clocks. Reviewed-by: Stefan Roese Signed-off-by: Baruch Siach --- board/solidrun/clearfog/clearfog.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/board/solidrun/clearfog/clearfog.c b/board/solidrun/clearfog/clearfog.c index 03724fee10c1..8b6381194688 100644 --- a/board/solidrun/clearfog/clearfog.c +++ b/board/solidrun/clearfog/clearfog.c @@ -68,7 +68,10 @@ static struct mv_ddr_topology_map board_topology_map = { BUS_MASK_32BIT, /* Busses mask */ MV_DDR_CFG_DEFAULT, /* ddr configuration data source */ { {0} }, /* raw spd data */ - {0} /* timing parameters */ + {0}, /* timing parameters */ + { {0} }, /* electrical configuration */ + {0,}, /* electrical parameters */ + 0x3, /* clock enable mask */ }; struct mv_ddr_topology_map *mv_ddr_topology_map_get(void) From patchwork Mon Jan 20 12:20:08 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Baruch Siach X-Patchwork-Id: 239813 List-Id: U-Boot discussion From: baruch at tkos.co.il (Baruch Siach) Date: Mon, 20 Jan 2020 14:20:08 +0200 Subject: [PATCH v2 03/10] cmd: add tlv_eeprom command In-Reply-To: References: Message-ID: <4af0f83f463ca09c4e68ea79068c11a181d0f5fd.1579522639.git.baruch@tkos.co.il> Add support for read/write of ONIE "Tlvinfo" EEPROM data format. TLV stands for Type-Length-Value. The data format is described here: https://opencomputeproject.github.io/onie/design-spec/hw_requirements.html#board-eeprom-information-format Based on U-Boot patch from the Open Compute project: https://github.com/opencomputeproject/onie/blob/ec87e872d46b9805565d2c6124b2f701ef1c07b1/patches/u-boot/common/feature-sys-eeprom-tlv-common.patch Keep only I2C EEPROM support. Use the generic eeprom driver. Fix checkpatch issues. Add support for multiple EEPROM TLV stores on the same system. This is useful in case of SOM and carrier that both provide ID and hardware configuration information. Add option to enable for SPL. This allows selection of RAM configuration based on EEPROM stored board identification. Signed-off-by: Baruch Siach Reviewed-by: Stefan Roese --- cmd/Kconfig | 14 + cmd/Makefile | 2 + cmd/tlv_eeprom.c | 1105 ++++++++++++++++++++++++++++++++++++++++++ include/tlv_eeprom.h | 164 +++++++ 4 files changed, 1285 insertions(+) create mode 100644 cmd/tlv_eeprom.c create mode 100644 include/tlv_eeprom.h diff --git a/cmd/Kconfig b/cmd/Kconfig index 298feae24d3f..b094f15ee155 100644 --- a/cmd/Kconfig +++ b/cmd/Kconfig @@ -242,6 +242,20 @@ config CMD_REGINFO help Register dump +config CMD_TLV_EEPROM + bool "tlv_eeprom" + depends on I2C_EEPROM + help + Display and program the system EEPROM data block in ONIE Tlvinfo + format. TLV stands for Type-Length-Value. + +config SPL_CMD_TLV_EEPROM + bool "tlv_eeprom for SPL" + depends on SPL_I2C_EEPROM + select SPL_DRIVERS_MISC_SUPPORT + help + Read system EEPROM data block in ONIE Tlvinfo format from SPL. + endmenu menu "Boot commands" diff --git a/cmd/Makefile b/cmd/Makefile index ecf687d49f38..ddc1368c7aea 100644 --- a/cmd/Makefile +++ b/cmd/Makefile @@ -184,6 +184,8 @@ obj-$(CONFIG_X86) += x86/ obj-$(CONFIG_ARCH_MVEBU) += mvebu/ endif # !CONFIG_SPL_BUILD +obj-$(CONFIG_$(SPL_)CMD_TLV_EEPROM) += tlv_eeprom.o + # core command obj-y += nvedit.o diff --git a/cmd/tlv_eeprom.c b/cmd/tlv_eeprom.c new file mode 100644 index 000000000000..71ce96ffc4ee --- /dev/null +++ b/cmd/tlv_eeprom.c @@ -0,0 +1,1105 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * See file CREDITS for list of people who contributed to this + * project. + * + * Copyright (C) 2013 Curt Brune + * Copyright (C) 2014 Srideep + * Copyright (C) 2013 Miles Tseng + * Copyright (C) 2014,2016 david_yang + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#include "tlv_eeprom.h" + +DECLARE_GLOBAL_DATA_PTR; + +#define MAX_TLV_DEVICES 2 + +/* File scope function prototypes */ +static bool is_checksum_valid(u8 *eeprom); +static int read_eeprom(u8 *eeprom); +static void show_eeprom(u8 *eeprom); +static void decode_tlv(struct tlvinfo_tlv *tlv); +static void update_crc(u8 *eeprom); +static int prog_eeprom(u8 *eeprom); +static bool tlvinfo_find_tlv(u8 *eeprom, u8 tcode, int *eeprom_index); +static bool tlvinfo_delete_tlv(u8 *eeprom, u8 code); +static bool tlvinfo_add_tlv(u8 *eeprom, int tcode, char *strval); +static int set_mac(char *buf, const char *string); +static int set_date(char *buf, const char *string); +static int set_bytes(char *buf, const char *string, int *converted_accum); +static void show_tlv_devices(void); + +/* Set to 1 if we've read EEPROM into memory */ +static int has_been_read; +/* The EERPOM contents after being read into memory */ +static u8 eeprom[TLV_INFO_MAX_LEN]; + +static struct udevice *tlv_devices[MAX_TLV_DEVICES]; +static unsigned int current_dev; + +#define to_header(p) ((struct tlvinfo_header *)p) +#define to_entry(p) ((struct tlvinfo_tlv *)p) + +#define HDR_SIZE sizeof(struct tlvinfo_header) +#define ENT_SIZE sizeof(struct tlvinfo_tlv) + +static inline bool is_digit(char c) +{ + return (c >= '0' && c <= '9'); +} + +/** + * is_valid_tlv + * + * Perform basic sanity checks on a TLV field. The TLV is pointed to + * by the parameter provided. + * 1. The type code is not reserved (0x00 or 0xFF) + */ +static inline bool is_valid_tlv(struct tlvinfo_tlv *tlv) +{ + return((tlv->type != 0x00) && (tlv->type != 0xFF)); +} + +/** + * is_hex + * + * Tests if character is an ASCII hex digit + */ +static inline u8 is_hex(char p) +{ + return (((p >= '0') && (p <= '9')) || + ((p >= 'A') && (p <= 'F')) || + ((p >= 'a') && (p <= 'f'))); +} + +/** + * is_checksum_valid + * + * Validate the checksum in the provided TlvInfo EEPROM data. First, + * verify that the TlvInfo header is valid, then make sure the last + * TLV is a CRC-32 TLV. Then calculate the CRC over the EEPROM data + * and compare it to the value stored in the EEPROM CRC-32 TLV. + */ +static bool is_checksum_valid(u8 *eeprom) +{ + struct tlvinfo_header *eeprom_hdr = to_header(eeprom); + struct tlvinfo_tlv *eeprom_crc; + unsigned int calc_crc; + unsigned int stored_crc; + + // Is the eeprom header valid? + if (!is_valid_tlvinfo_header(eeprom_hdr)) + return FALSE; + + // Is the last TLV a CRC? + eeprom_crc = to_entry(&eeprom[HDR_SIZE + + be16_to_cpu(eeprom_hdr->totallen) - (ENT_SIZE + 4)]); + if (eeprom_crc->type != TLV_CODE_CRC_32 || eeprom_crc->length != 4) + return FALSE; + + // Calculate the checksum + calc_crc = crc32(0, (void *)eeprom, + HDR_SIZE + be16_to_cpu(eeprom_hdr->totallen) - 4); + stored_crc = (eeprom_crc->value[0] << 24) | + (eeprom_crc->value[1] << 16) | + (eeprom_crc->value[2] << 8) | + eeprom_crc->value[3]; + return calc_crc == stored_crc; +} + +/** + * read_eeprom + * + * Read the EEPROM into memory, if it hasn't already been read. + */ +static int read_eeprom(u8 *eeprom) +{ + int ret; + struct tlvinfo_header *eeprom_hdr = to_header(eeprom); + struct tlvinfo_tlv *eeprom_tlv = to_entry(&eeprom[HDR_SIZE]); + + if (has_been_read) + return 0; + + /* Read the header */ + ret = read_tlv_eeprom((void *)eeprom_hdr, 0, HDR_SIZE, current_dev); + /* If the header was successfully read, read the TLVs */ + if (ret == 0 && is_valid_tlvinfo_header(eeprom_hdr)) + ret = read_tlv_eeprom((void *)eeprom_tlv, HDR_SIZE, + be16_to_cpu(eeprom_hdr->totallen), + current_dev); + + // If the contents are invalid, start over with default contents + if (!is_valid_tlvinfo_header(eeprom_hdr) || + !is_checksum_valid(eeprom)) { + strcpy(eeprom_hdr->signature, TLV_INFO_ID_STRING); + eeprom_hdr->version = TLV_INFO_VERSION; + eeprom_hdr->totallen = cpu_to_be16(0); + update_crc(eeprom); + } + + has_been_read = 1; + +#ifdef DEBUG + show_eeprom(eeprom); +#endif + + return ret; +} + +/** + * show_eeprom + * + * Display the contents of the EEPROM + */ +static void show_eeprom(u8 *eeprom) +{ + int tlv_end; + int curr_tlv; + struct tlvinfo_header *eeprom_hdr = to_header(eeprom); + struct tlvinfo_tlv *eeprom_tlv; + + if (!is_valid_tlvinfo_header(eeprom_hdr)) { + printf("EEPROM does not contain data in a valid TlvInfo format.\n"); + return; + } + + printf("TLV: %u\n", current_dev); + printf("TlvInfo Header:\n"); + printf(" Id String: %s\n", eeprom_hdr->signature); + printf(" Version: %d\n", eeprom_hdr->version); + printf(" Total Length: %d\n", be16_to_cpu(eeprom_hdr->totallen)); + + printf("TLV Name Code Len Value\n"); + printf("-------------------- ---- --- -----\n"); + curr_tlv = HDR_SIZE; + tlv_end = HDR_SIZE + be16_to_cpu(eeprom_hdr->totallen); + while (curr_tlv < tlv_end) { + eeprom_tlv = to_entry(&eeprom[curr_tlv]); + if (!is_valid_tlv(eeprom_tlv)) { + printf("Invalid TLV field starting at EEPROM offset %d\n", + curr_tlv); + return; + } + decode_tlv(eeprom_tlv); + curr_tlv += ENT_SIZE + eeprom_tlv->length; + } + + printf("Checksum is %s.\n", + is_checksum_valid(eeprom) ? "valid" : "invalid"); + +#ifdef DEBUG + printf("EEPROM dump: (0x%x bytes)", TLV_INFO_MAX_LEN); + for (i = 0; i < TLV_INFO_MAX_LEN; i++) { + if ((i % 16) == 0) + printf("\n%02X: ", i); + printf("%02X ", eeprom[i]); + } + printf("\n"); +#endif +} + +/** + * Struct for displaying the TLV codes and names. + */ +struct tlv_code_desc { + u8 m_code; + char *m_name; +}; + +/** + * List of TLV codes and names. + */ +static struct tlv_code_desc tlv_code_list[] = { + { TLV_CODE_PRODUCT_NAME, "Product Name"}, + { TLV_CODE_PART_NUMBER, "Part Number"}, + { TLV_CODE_SERIAL_NUMBER, "Serial Number"}, + { TLV_CODE_MAC_BASE, "Base MAC Address"}, + { TLV_CODE_MANUF_DATE, "Manufacture Date"}, + { TLV_CODE_DEVICE_VERSION, "Device Version"}, + { TLV_CODE_LABEL_REVISION, "Label Revision"}, + { TLV_CODE_PLATFORM_NAME, "Platform Name"}, + { TLV_CODE_ONIE_VERSION, "ONIE Version"}, + { TLV_CODE_MAC_SIZE, "MAC Addresses"}, + { TLV_CODE_MANUF_NAME, "Manufacturer"}, + { TLV_CODE_MANUF_COUNTRY, "Country Code"}, + { TLV_CODE_VENDOR_NAME, "Vendor Name"}, + { TLV_CODE_DIAG_VERSION, "Diag Version"}, + { TLV_CODE_SERVICE_TAG, "Service Tag"}, + { TLV_CODE_VENDOR_EXT, "Vendor Extension"}, + { TLV_CODE_CRC_32, "CRC-32"}, +}; + +/** + * Look up a TLV name by its type. + */ +static inline const char *tlv_type2name(u8 type) +{ + char *name = "Unknown"; + int i; + + for (i = 0; i < ARRAY_SIZE(tlv_code_list); i++) { + if (tlv_code_list[i].m_code == type) { + name = tlv_code_list[i].m_name; + break; + } + } + + return name; +} + +/* + * decode_tlv + * + * Print a string representing the contents of the TLV field. The format of + * the string is: + * 1. The name of the field left justified in 20 characters + * 2. The type code in hex right justified in 5 characters + * 3. The length in decimal right justified in 4 characters + * 4. The value, left justified in however many characters it takes + * The validity of EEPROM contents and the TLV field have been verified + * prior to calling this function. + */ +#define DECODE_NAME_MAX 20 + +/* + * The max decode value is currently for the 'raw' type or the 'vendor + * extension' type, both of which have the same decode format. The + * max decode string size is computed as follows: + * + * strlen(" 0xFF") * TLV_VALUE_MAX_LEN + 1 + * + */ +#define DECODE_VALUE_MAX ((5 * TLV_VALUE_MAX_LEN) + 1) + +static void decode_tlv(struct tlvinfo_tlv *tlv) +{ + char name[DECODE_NAME_MAX]; + char value[DECODE_VALUE_MAX]; + int i; + + strncpy(name, tlv_type2name(tlv->type), DECODE_NAME_MAX); + + switch (tlv->type) { + case TLV_CODE_PRODUCT_NAME: + case TLV_CODE_PART_NUMBER: + case TLV_CODE_SERIAL_NUMBER: + case TLV_CODE_MANUF_DATE: + case TLV_CODE_LABEL_REVISION: + case TLV_CODE_PLATFORM_NAME: + case TLV_CODE_ONIE_VERSION: + case TLV_CODE_MANUF_NAME: + case TLV_CODE_MANUF_COUNTRY: + case TLV_CODE_VENDOR_NAME: + case TLV_CODE_DIAG_VERSION: + case TLV_CODE_SERVICE_TAG: + memcpy(value, tlv->value, tlv->length); + value[tlv->length] = 0; + break; + case TLV_CODE_MAC_BASE: + sprintf(value, "%02X:%02X:%02X:%02X:%02X:%02X", + tlv->value[0], tlv->value[1], tlv->value[2], + tlv->value[3], tlv->value[4], tlv->value[5]); + break; + case TLV_CODE_DEVICE_VERSION: + sprintf(value, "%u", tlv->value[0]); + break; + case TLV_CODE_MAC_SIZE: + sprintf(value, "%u", (tlv->value[0] << 8) | tlv->value[1]); + break; + case TLV_CODE_VENDOR_EXT: + value[0] = 0; + for (i = 0; (i < (DECODE_VALUE_MAX / 5)) && (i < tlv->length); + i++) { + sprintf(value, "%s 0x%02X", value, tlv->value[i]); + } + break; + case TLV_CODE_CRC_32: + sprintf(value, "0x%02X%02X%02X%02X", + tlv->value[0], tlv->value[1], + tlv->value[2], tlv->value[3]); + break; + default: + value[0] = 0; + for (i = 0; (i < (DECODE_VALUE_MAX / 5)) && (i < tlv->length); + i++) { + sprintf(value, "%s 0x%02X", value, tlv->value[i]); + } + break; + } + + name[DECODE_NAME_MAX - 1] = 0; + printf("%-20s 0x%02X %3d %s\n", name, tlv->type, tlv->length, value); +} + +/** + * update_crc + * + * This function updates the CRC-32 TLV. If there is no CRC-32 TLV, then + * one is added. This function should be called after each update to the + * EEPROM structure, to make sure the CRC is always correct. + */ +static void update_crc(u8 *eeprom) +{ + struct tlvinfo_header *eeprom_hdr = to_header(eeprom); + struct tlvinfo_tlv *eeprom_crc; + unsigned int calc_crc; + int eeprom_index; + + // Discover the CRC TLV + if (!tlvinfo_find_tlv(eeprom, TLV_CODE_CRC_32, &eeprom_index)) { + unsigned int totallen = be16_to_cpu(eeprom_hdr->totallen); + + if ((totallen + ENT_SIZE + 4) > TLV_TOTAL_LEN_MAX) + return; + eeprom_index = HDR_SIZE + totallen; + eeprom_hdr->totallen = cpu_to_be16(totallen + ENT_SIZE + 4); + } + eeprom_crc = to_entry(&eeprom[eeprom_index]); + eeprom_crc->type = TLV_CODE_CRC_32; + eeprom_crc->length = 4; + + // Calculate the checksum + calc_crc = crc32(0, (void *)eeprom, + HDR_SIZE + be16_to_cpu(eeprom_hdr->totallen) - 4); + eeprom_crc->value[0] = (calc_crc >> 24) & 0xFF; + eeprom_crc->value[1] = (calc_crc >> 16) & 0xFF; + eeprom_crc->value[2] = (calc_crc >> 8) & 0xFF; + eeprom_crc->value[3] = (calc_crc >> 0) & 0xFF; +} + +/** + * prog_eeprom + * + * Write the EEPROM data from CPU memory to the hardware. + */ +static int prog_eeprom(u8 *eeprom) +{ + int ret = 0; + struct tlvinfo_header *eeprom_hdr = to_header(eeprom); + int eeprom_len; + + update_crc(eeprom); + + eeprom_len = HDR_SIZE + be16_to_cpu(eeprom_hdr->totallen); + ret = write_tlv_eeprom(eeprom, eeprom_len); + if (ret) { + printf("Programming failed.\n"); + return -1; + } + + printf("Programming passed.\n"); + return 0; +} + +/** + * show_tlv_code_list - Display the list of TLV codes and names + */ +void show_tlv_code_list(void) +{ + int i; + + printf("TLV Code TLV Name\n"); + printf("======== =================\n"); + for (i = 0; i < ARRAY_SIZE(tlv_code_list); i++) { + printf("0x%02X %s\n", + tlv_code_list[i].m_code, + tlv_code_list[i].m_name); + } +} + +/** + * do_tlv_eeprom + * + * This function implements the tlv_eeprom command. + */ +int do_tlv_eeprom(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[]) +{ + char cmd; + struct tlvinfo_header *eeprom_hdr = to_header(eeprom); + + // If no arguments, read the EERPOM and display its contents + if (argc == 1) { + read_eeprom(eeprom); + show_eeprom(eeprom); + return 0; + } + + // We only look at the first character to the command, so "read" and + // "reset" will both be treated as "read". + cmd = argv[1][0]; + + // Read the EEPROM contents + if (cmd == 'r') { + has_been_read = 0; + if (!read_eeprom(eeprom)) + printf("EEPROM data loaded from device to memory.\n"); + return 0; + } + + // Subsequent commands require that the EEPROM has already been read. + if (!has_been_read) { + printf("Please read the EEPROM data first, using the 'tlv_eeprom read' command.\n"); + return 0; + } + + // Handle the commands that don't take parameters + if (argc == 2) { + switch (cmd) { + case 'w': /* write */ + prog_eeprom(eeprom); + break; + case 'e': /* erase */ + strcpy(eeprom_hdr->signature, TLV_INFO_ID_STRING); + eeprom_hdr->version = TLV_INFO_VERSION; + eeprom_hdr->totallen = cpu_to_be16(0); + update_crc(eeprom); + printf("EEPROM data in memory reset.\n"); + break; + case 'l': /* list */ + show_tlv_code_list(); + break; + case 'd': /* dev */ + show_tlv_devices(); + break; + default: + cmd_usage(cmdtp); + break; + } + return 0; + } + + // The set command takes one or two args. + if (argc > 4) { + cmd_usage(cmdtp); + return 0; + } + + // Set command. If the TLV exists in the EEPROM, delete it. Then if + // data was supplied for this TLV add the TLV with the new contents at + // the end. + if (cmd == 's') { + int tcode; + + tcode = simple_strtoul(argv[2], NULL, 0); + tlvinfo_delete_tlv(eeprom, tcode); + if (argc == 4) + tlvinfo_add_tlv(eeprom, tcode, argv[3]); + } else if (cmd == 'd') { /* 'dev' command */ + unsigned int devnum; + + devnum = simple_strtoul(argv[2], NULL, 0); + if (devnum > MAX_TLV_DEVICES || !tlv_devices[devnum]) { + printf("Invalid device number\n"); + return 0; + } + current_dev = devnum; + has_been_read = 0; + } else { + cmd_usage(cmdtp); + } + + return 0; +} + +/** + * This macro defines the tlv_eeprom command line command. + */ +U_BOOT_CMD(tlv_eeprom, 4, 1, do_tlv_eeprom, + "Display and program the system EEPROM data block.", + "[read|write|set |erase|list]\n" + "tlv_eeprom\n" + " - With no arguments display the current contents.\n" + "tlv_eeprom dev [dev]\n" + " - List devices or set current EEPROM device.\n" + "tlv_eeprom read\n" + " - Load EEPROM data from device to memory.\n" + "tlv_eeprom write\n" + " - Write the EEPROM data to persistent storage.\n" + "tlv_eeprom set \n" + " - Set a field to a value.\n" + " - If no string_value, field is deleted.\n" + " - Use 'tlv_eeprom write' to make changes permanent.\n" + "tlv_eeprom erase\n" + " - Reset the in memory EEPROM data.\n" + " - Use 'tlv_eeprom read' to refresh the in memory EEPROM data.\n" + " - Use 'tlv_eeprom write' to make changes permanent.\n" + "tlv_eeprom list\n" + " - List the understood TLV codes and names.\n" + ); + +/** + * tlvinfo_find_tlv + * + * This function finds the TLV with the supplied code in the EERPOM. + * An offset from the beginning of the EEPROM is returned in the + * eeprom_index parameter if the TLV is found. + */ +static bool tlvinfo_find_tlv(u8 *eeprom, u8 tcode, int *eeprom_index) +{ + struct tlvinfo_header *eeprom_hdr = to_header(eeprom); + struct tlvinfo_tlv *eeprom_tlv; + int eeprom_end; + + // Search through the TLVs, looking for the first one which matches the + // supplied type code. + *eeprom_index = HDR_SIZE; + eeprom_end = HDR_SIZE + be16_to_cpu(eeprom_hdr->totallen); + while (*eeprom_index < eeprom_end) { + eeprom_tlv = to_entry(&eeprom[*eeprom_index]); + if (!is_valid_tlv(eeprom_tlv)) + return FALSE; + if (eeprom_tlv->type == tcode) + return TRUE; + *eeprom_index += ENT_SIZE + eeprom_tlv->length; + } + return(FALSE); +} + +/** + * tlvinfo_delete_tlv + * + * This function deletes the TLV with the specified type code from the + * EEPROM. + */ +static bool tlvinfo_delete_tlv(u8 *eeprom, u8 code) +{ + int eeprom_index; + int tlength; + struct tlvinfo_header *eeprom_hdr = to_header(eeprom); + struct tlvinfo_tlv *eeprom_tlv; + + // Find the TLV and then move all following TLVs "forward" + if (tlvinfo_find_tlv(eeprom, code, &eeprom_index)) { + eeprom_tlv = to_entry(&eeprom[eeprom_index]); + tlength = ENT_SIZE + eeprom_tlv->length; + memcpy(&eeprom[eeprom_index], &eeprom[eeprom_index + tlength], + HDR_SIZE + + be16_to_cpu(eeprom_hdr->totallen) - eeprom_index - + tlength); + eeprom_hdr->totallen = + cpu_to_be16(be16_to_cpu(eeprom_hdr->totallen) - + tlength); + update_crc(eeprom); + return TRUE; + } + return FALSE; +} + +/** + * tlvinfo_add_tlv + * + * This function adds a TLV to the EEPROM, converting the value (a string) to + * the format in which it will be stored in the EEPROM. + */ +#define MAX_TLV_VALUE_LEN 256 +static bool tlvinfo_add_tlv(u8 *eeprom, int tcode, char *strval) +{ + struct tlvinfo_header *eeprom_hdr = to_header(eeprom); + struct tlvinfo_tlv *eeprom_tlv; + int new_tlv_len = 0; + u32 value; + char data[MAX_TLV_VALUE_LEN]; + int eeprom_index; + + // Encode each TLV type into the format to be stored in the EERPOM + switch (tcode) { + case TLV_CODE_PRODUCT_NAME: + case TLV_CODE_PART_NUMBER: + case TLV_CODE_SERIAL_NUMBER: + case TLV_CODE_LABEL_REVISION: + case TLV_CODE_PLATFORM_NAME: + case TLV_CODE_ONIE_VERSION: + case TLV_CODE_MANUF_NAME: + case TLV_CODE_MANUF_COUNTRY: + case TLV_CODE_VENDOR_NAME: + case TLV_CODE_DIAG_VERSION: + case TLV_CODE_SERVICE_TAG: + strncpy(data, strval, MAX_TLV_VALUE_LEN); + new_tlv_len = min_t(size_t, MAX_TLV_VALUE_LEN, strlen(strval)); + break; + case TLV_CODE_DEVICE_VERSION: + value = simple_strtoul(strval, NULL, 0); + if (value >= 256) { + printf("ERROR: Device version must be 255 or less. Value supplied: %u", + value); + return FALSE; + } + data[0] = value & 0xFF; + new_tlv_len = 1; + break; + case TLV_CODE_MAC_SIZE: + value = simple_strtoul(strval, NULL, 0); + if (value >= 65536) { + printf("ERROR: MAC Size must be 65535 or less. Value supplied: %u", + value); + return FALSE; + } + data[0] = (value >> 8) & 0xFF; + data[1] = value & 0xFF; + new_tlv_len = 2; + break; + case TLV_CODE_MANUF_DATE: + if (set_date(data, strval) != 0) + return FALSE; + new_tlv_len = 19; + break; + case TLV_CODE_MAC_BASE: + if (set_mac(data, strval) != 0) + return FALSE; + new_tlv_len = 6; + break; + case TLV_CODE_CRC_32: + printf("WARNING: The CRC TLV is set automatically and cannot be set manually.\n"); + return FALSE; + case TLV_CODE_VENDOR_EXT: + default: + if (set_bytes(data, strval, &new_tlv_len) != 0) + return FALSE; + break; + } + + // Is there room for this TLV? + if ((be16_to_cpu(eeprom_hdr->totallen) + ENT_SIZE + new_tlv_len) > + TLV_TOTAL_LEN_MAX) { + printf("ERROR: There is not enough room in the EERPOM to save data.\n"); + return FALSE; + } + + // Add TLV at the end, overwriting CRC TLV if it exists + if (tlvinfo_find_tlv(eeprom, TLV_CODE_CRC_32, &eeprom_index)) + eeprom_hdr->totallen = + cpu_to_be16(be16_to_cpu(eeprom_hdr->totallen) - + ENT_SIZE - 4); + else + eeprom_index = HDR_SIZE + be16_to_cpu(eeprom_hdr->totallen); + eeprom_tlv = to_entry(&eeprom[eeprom_index]); + eeprom_tlv->type = tcode; + eeprom_tlv->length = new_tlv_len; + memcpy(eeprom_tlv->value, data, new_tlv_len); + + // Update the total length and calculate (add) a new CRC-32 TLV + eeprom_hdr->totallen = cpu_to_be16(be16_to_cpu(eeprom_hdr->totallen) + + ENT_SIZE + new_tlv_len); + update_crc(eeprom); + + return TRUE; +} + +/** + * set_mac + * + * Converts a string MAC address into a binary buffer. + * + * This function takes a pointer to a MAC address string + * (i.e."XX:XX:XX:XX:XX:XX", where "XX" is a two-digit hex number). + * The string format is verified and then converted to binary and + * stored in a buffer. + */ +static int set_mac(char *buf, const char *string) +{ + char *p = (char *)string; + int i; + int err = 0; + char *end; + + if (!p) { + printf("ERROR: NULL mac addr string passed in.\n"); + return -1; + } + + if (strlen(p) != 17) { + printf("ERROR: MAC address strlen() != 17 -- %zu\n", strlen(p)); + printf("ERROR: Bad MAC address format: %s\n", string); + return -1; + } + + for (i = 0; i < 17; i++) { + if ((i % 3) == 2) { + if (p[i] != ':') { + err++; + printf("ERROR: mac: p[%i] != :, found: `%c'\n", + i, p[i]); + break; + } + continue; + } else if (!is_hex(p[i])) { + err++; + printf("ERROR: mac: p[%i] != hex digit, found: `%c'\n", + i, p[i]); + break; + } + } + + if (err != 0) { + printf("ERROR: Bad MAC address format: %s\n", string); + return -1; + } + + /* Convert string to binary */ + for (i = 0, p = (char *)string; i < 6; i++) { + buf[i] = p ? simple_strtoul(p, &end, 16) : 0; + if (p) + p = (*end) ? end + 1 : end; + } + + if (!is_valid_ethaddr((u8 *)buf)) { + printf("ERROR: MAC address must not be 00:00:00:00:00:00, a multicast address or FF:FF:FF:FF:FF:FF.\n"); + printf("ERROR: Bad MAC address format: %s\n", string); + return -1; + } + + return 0; +} + +/** + * set_date + * + * Validates the format of the data string + * + * This function takes a pointer to a date string (i.e. MM/DD/YYYY hh:mm:ss) + * and validates that the format is correct. If so the string is copied + * to the supplied buffer. + */ +static int set_date(char *buf, const char *string) +{ + int i; + + if (!string) { + printf("ERROR: NULL date string passed in.\n"); + return -1; + } + + if (strlen(string) != 19) { + printf("ERROR: Date strlen() != 19 -- %zu\n", strlen(string)); + printf("ERROR: Bad date format (MM/DD/YYYY hh:mm:ss): %s\n", + string); + return -1; + } + + for (i = 0; string[i] != 0; i++) { + switch (i) { + case 2: + case 5: + if (string[i] != '/') { + printf("ERROR: Bad date format (MM/DD/YYYY hh:mm:ss): %s\n", + string); + return -1; + } + break; + case 10: + if (string[i] != ' ') { + printf("ERROR: Bad date format (MM/DD/YYYY hh:mm:ss): %s\n", + string); + return -1; + } + break; + case 13: + case 16: + if (string[i] != ':') { + printf("ERROR: Bad date format (MM/DD/YYYY hh:mm:ss): %s\n", + string); + return -1; + } + break; + default: + if (!is_digit(string[i])) { + printf("ERROR: Bad date format (MM/DD/YYYY hh:mm:ss): %s\n", + string); + return -1; + } + break; + } + } + + strcpy(buf, string); + return 0; +} + +/** + * set_bytes + * + * Converts a space-separated string of decimal numbers into a + * buffer of bytes. + * + * This function takes a pointer to a space-separated string of decimal + * numbers (i.e. "128 0x55 0321") with "C" standard radix specifiers + * and converts them to an array of bytes. + */ +static int set_bytes(char *buf, const char *string, int *converted_accum) +{ + char *p = (char *)string; + int i; + uint byte; + + if (!p) { + printf("ERROR: NULL string passed in.\n"); + return -1; + } + + /* Convert string to bytes */ + for (i = 0, p = (char *)string; (i < TLV_VALUE_MAX_LEN) && (*p != 0); + i++) { + while ((*p == ' ') || (*p == '\t') || (*p == ',') || + (*p == ';')) { + p++; + } + if (*p != 0) { + if (!is_digit(*p)) { + printf("ERROR: Non-digit found in byte string: (%s)\n", + string); + return -1; + } + byte = simple_strtoul(p, &p, 0); + if (byte >= 256) { + printf("ERROR: The value specified is greater than 255: (%u) in string: %s\n", + byte, string); + return -1; + } + buf[i] = byte & 0xFF; + } + } + + if (i == TLV_VALUE_MAX_LEN && (*p != 0)) { + printf("ERROR: Trying to assign too many bytes (max: %d) in string: %s\n", + TLV_VALUE_MAX_LEN, string); + return -1; + } + + *converted_accum = i; + return 0; +} + +static void show_tlv_devices(void) +{ + unsigned int dev; + + for (dev = 0; dev < MAX_TLV_DEVICES; dev++) + if (tlv_devices[dev]) + printf("TLV: %u%s\n", dev, + (dev == current_dev) ? " (*)" : ""); +} + +static int find_tlv_devices(struct udevice **tlv_devices_p) +{ + int ret; + int count_dev = 0; + struct udevice *dev; + + for (ret = uclass_first_device_check(UCLASS_I2C_EEPROM, &dev); + dev; + ret = uclass_next_device_check(&dev)) { + if (ret == 0) + tlv_devices_p[count_dev++] = dev; + if (count_dev >= MAX_TLV_DEVICES) + break; + } + + return (count_dev == 0) ? -ENODEV : 0; +} + +static struct udevice *find_tlv_device_by_index(int dev_num) +{ + struct udevice *local_tlv_devices[MAX_TLV_DEVICES] = {}; + struct udevice **tlv_devices_p; + int ret; + + if (gd->flags & (GD_FLG_RELOC | GD_FLG_SPL_INIT)) { + /* Assume BSS is initialized; use static data */ + if (tlv_devices[dev_num]) + return tlv_devices[dev_num]; + tlv_devices_p = tlv_devices; + } else { + tlv_devices_p = local_tlv_devices; + } + + ret = find_tlv_devices(tlv_devices_p); + if (ret == 0 && tlv_devices_p[dev_num]) + return tlv_devices_p[dev_num]; + + return NULL; +} + +/** + * read_tlv_eeprom - read the hwinfo from i2c EEPROM + */ +int read_tlv_eeprom(void *eeprom, int offset, int len, int dev_num) +{ + struct udevice *dev; + + if (dev_num >= MAX_TLV_DEVICES) + return -EINVAL; + + dev = find_tlv_device_by_index(dev_num); + if (!dev) + return -ENODEV; + + return i2c_eeprom_read(dev, offset, eeprom, len); +} + +/** + * write_tlv_eeprom - write the hwinfo to i2c EEPROM + */ +int write_tlv_eeprom(void *eeprom, int len) +{ + if (!(gd->flags & GD_FLG_RELOC)) + return -ENODEV; + if (!tlv_devices[current_dev]) + return -ENODEV; + + return i2c_eeprom_write(tlv_devices[current_dev], 0, eeprom, len); +} + +int read_tlvinfo_tlv_eeprom(void *eeprom, struct tlvinfo_header **hdr, + struct tlvinfo_tlv **first_entry, int dev_num) +{ + int ret; + struct tlvinfo_header *tlv_hdr; + struct tlvinfo_tlv *tlv_ent; + + /* Read TLV header */ + ret = read_tlv_eeprom(eeprom, 0, HDR_SIZE, dev_num); + if (ret < 0) + return ret; + + tlv_hdr = eeprom; + if (!is_valid_tlvinfo_header(tlv_hdr)) + return -EINVAL; + + /* Read TLV entries */ + tlv_ent = to_entry(&tlv_hdr[1]); + ret = read_tlv_eeprom(tlv_ent, HDR_SIZE, + be16_to_cpu(tlv_hdr->totallen), dev_num); + if (ret < 0) + return ret; + if (!is_checksum_valid(eeprom)) + return -EINVAL; + + *hdr = tlv_hdr; + *first_entry = tlv_ent; + + return 0; +} + +/** + * mac_read_from_eeprom + * + * Read the MAC addresses from EEPROM + * + * This function reads the MAC addresses from EEPROM and sets the + * appropriate environment variables for each one read. + * + * The environment variables are only set if they haven't been set already. + * This ensures that any user-saved variables are never overwritten. + * + * This function must be called after relocation. + */ +int mac_read_from_eeprom(void) +{ + unsigned int i; + int eeprom_index; + struct tlvinfo_tlv *eeprom_tlv; + int maccount; + u8 macbase[6]; + struct tlvinfo_header *eeprom_hdr = to_header(eeprom); + + puts("EEPROM: "); + + if (read_eeprom(eeprom)) { + printf("Read failed.\n"); + return -1; + } + + maccount = 1; + if (tlvinfo_find_tlv(eeprom, TLV_CODE_MAC_SIZE, &eeprom_index)) { + eeprom_tlv = to_entry(&eeprom[eeprom_index]); + maccount = (eeprom_tlv->value[0] << 8) | eeprom_tlv->value[1]; + } + + memcpy(macbase, "\0\0\0\0\0\0", 6); + if (tlvinfo_find_tlv(eeprom, TLV_CODE_MAC_BASE, &eeprom_index)) { + eeprom_tlv = to_entry(&eeprom[eeprom_index]); + memcpy(macbase, eeprom_tlv->value, 6); + } + + for (i = 0; i < maccount; i++) { + if (is_valid_ethaddr(macbase)) { + char ethaddr[18]; + char enetvar[11]; + + sprintf(ethaddr, "%02X:%02X:%02X:%02X:%02X:%02X", + macbase[0], macbase[1], macbase[2], + macbase[3], macbase[4], macbase[5]); + sprintf(enetvar, i ? "eth%daddr" : "ethaddr", i); + /* Only initialize environment variables that are blank + * (i.e. have not yet been set) + */ + if (!env_get(enetvar)) + env_set(enetvar, ethaddr); + + macbase[5]++; + if (macbase[5] == 0) { + macbase[4]++; + if (macbase[4] == 0) { + macbase[3]++; + if (macbase[3] == 0) { + macbase[0] = 0; + macbase[1] = 0; + macbase[2] = 0; + } + } + } + } + } + + printf("%s v%u len=%u\n", eeprom_hdr->signature, eeprom_hdr->version, + be16_to_cpu(eeprom_hdr->totallen)); + + return 0; +} + +/** + * populate_serial_number - read the serial number from EEPROM + * + * This function reads the serial number from the EEPROM and sets the + * appropriate environment variable. + * + * The environment variable is only set if it has not been set + * already. This ensures that any user-saved variables are never + * overwritten. + * + * This function must be called after relocation. + */ +int populate_serial_number(void) +{ + char serialstr[257]; + int eeprom_index; + struct tlvinfo_tlv *eeprom_tlv; + + if (env_get("serial#")) + return 0; + + if (read_eeprom(eeprom)) { + printf("Read failed.\n"); + return -1; + } + + if (tlvinfo_find_tlv(eeprom, TLV_CODE_SERIAL_NUMBER, &eeprom_index)) { + eeprom_tlv = to_entry(&eeprom[eeprom_index]); + memcpy(serialstr, eeprom_tlv->value, eeprom_tlv->length); + serialstr[eeprom_tlv->length] = 0; + env_set("serial#", serialstr); + } + + return 0; +} diff --git a/include/tlv_eeprom.h b/include/tlv_eeprom.h new file mode 100644 index 000000000000..b506acb5ae57 --- /dev/null +++ b/include/tlv_eeprom.h @@ -0,0 +1,164 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * See file CREDITS for list of people who contributed to this + * project. + */ + +#ifndef __TLV_EEPROM_H_ +#define __TLV_EEPROM_H_ + +/* + * Without getting too philosophical, define truth, falsehood, and the + * boolean type, if they are not already defined. + */ +#ifndef FALSE +#define FALSE 0 +#endif + +#ifndef TRUE +#define TRUE (!FALSE) +#endif + +/* + * The Definition of the TlvInfo EEPROM format can be found at onie.org or + * github.com/onie + */ + +/* + * TlvInfo header: Layout of the header for the TlvInfo format + * + * See the end of this file for details of this eeprom format + */ +struct __attribute__ ((__packed__)) tlvinfo_header { + char signature[8]; /* 0x00 - 0x07 EEPROM Tag "TlvInfo" */ + u8 version; /* 0x08 Structure version */ + u16 totallen; /* 0x09 - 0x0A Length of all data which follows */ +}; + +// Header Field Constants +#define TLV_INFO_ID_STRING "TlvInfo" +#define TLV_INFO_VERSION 0x01 +#define TLV_INFO_MAX_LEN 2048 +#define TLV_TOTAL_LEN_MAX (TLV_INFO_MAX_LEN - \ + sizeof(struct tlvinfo_header)) + +/* + * TlvInfo TLV: Layout of a TLV field + */ +struct __attribute__ ((__packed__)) tlvinfo_tlv { + u8 type; + u8 length; + u8 value[0]; +}; + +/* Maximum length of a TLV value in bytes */ +#define TLV_VALUE_MAX_LEN 255 + +/** + * The TLV Types. + * + * Keep these in sync with tlv_code_list in cmd/tlv_eeprom.c + */ +#define TLV_CODE_PRODUCT_NAME 0x21 +#define TLV_CODE_PART_NUMBER 0x22 +#define TLV_CODE_SERIAL_NUMBER 0x23 +#define TLV_CODE_MAC_BASE 0x24 +#define TLV_CODE_MANUF_DATE 0x25 +#define TLV_CODE_DEVICE_VERSION 0x26 +#define TLV_CODE_LABEL_REVISION 0x27 +#define TLV_CODE_PLATFORM_NAME 0x28 +#define TLV_CODE_ONIE_VERSION 0x29 +#define TLV_CODE_MAC_SIZE 0x2A +#define TLV_CODE_MANUF_NAME 0x2B +#define TLV_CODE_MANUF_COUNTRY 0x2C +#define TLV_CODE_VENDOR_NAME 0x2D +#define TLV_CODE_DIAG_VERSION 0x2E +#define TLV_CODE_SERVICE_TAG 0x2F +#define TLV_CODE_VENDOR_EXT 0xFD +#define TLV_CODE_CRC_32 0xFE + +#if CONFIG_IS_ENABLED(CMD_TLV_EEPROM) + +/** + * read_tlv_eeprom - Read the EEPROM binary data from the hardware + * @eeprom: Pointer to buffer to hold the binary data + * @offset: Offset within EEPROM block to read data from + * @len : Maximum size of buffer + * @dev : EEPROM device to read + * + * Note: this routine does not validate the EEPROM data. + * + */ + +int read_tlv_eeprom(void *eeprom, int offset, int len, int dev); + +/** + * write_tlv_eeprom - Write the entire EEPROM binary data to the hardware + * @eeprom: Pointer to buffer to hold the binary data + * @len : Maximum size of buffer + * + * Note: this routine does not validate the EEPROM data. + * + */ +int write_tlv_eeprom(void *eeprom, int len); + +/** + * read_tlvinfo_tlv_eeprom - Read the TLV from EEPROM, and validate + * @eeprom: Pointer to buffer to hold the binary data. Must point to a buffer + * of size at least TLV_INFO_MAX_LEN. + * @hdr : Points to pointer to TLV header (output) + * @first_entry : Points to pointer to first TLV entry (output) + * @dev : EEPROM device to read + * + * Store the raw EEPROM data from EEPROM @dev in the @eeprom buffer. If TLV is + * valid set *@hdr and *@first_entry. + * + * Returns 0 when read from EEPROM is successful, and the data is valid. + * Returns <0 error value when EEPROM read fails. Return -EINVAL when TLV is + * invalid. + * + */ + +int read_tlvinfo_tlv_eeprom(void *eeprom, struct tlvinfo_header **hdr, + struct tlvinfo_tlv **first_entry, int dev); + +#else /* !CONFIG_IS_ENABLED(CMD_TLV_EEPROM) */ + +static inline int read_tlv_eeprom(void *eeprom, int offset, int len, int dev) +{ + return -ENOTSUPP; +} + +static inline int write_tlv_eeprom(void *eeprom, int len) +{ + return -ENOTSUPP; +} + +static inline int +read_tlvinfo_tlv_eeprom(void *eeprom, struct tlvinfo_header **hdr, + struct tlvinfo_tlv **first_entry, int dev) +{ + return -ENOTSUPP; +} + +#endif /* CONFIG_IS_ENABLED(CMD_TLV_EEPROM) */ + +/** + * is_valid_tlvinfo_header + * + * Perform sanity checks on the first 11 bytes of the TlvInfo EEPROM + * data pointed to by the parameter: + * 1. First 8 bytes contain null-terminated ASCII string "TlvInfo" + * 2. Version byte is 1 + * 3. Total length bytes contain value which is less than or equal + * to the allowed maximum (2048-11) + * + */ +static inline bool is_valid_tlvinfo_header(struct tlvinfo_header *hdr) +{ + return ((strcmp(hdr->signature, TLV_INFO_ID_STRING) == 0) && + (hdr->version == TLV_INFO_VERSION) && + (be16_to_cpu(hdr->totallen) <= TLV_TOTAL_LEN_MAX)); +} + +#endif /* __TLV_EEPROM_H_ */ From patchwork Mon Jan 20 12:20:09 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Baruch Siach X-Patchwork-Id: 239809 List-Id: U-Boot discussion From: baruch at tkos.co.il (Baruch Siach) Date: Mon, 20 Jan 2020 14:20:09 +0200 Subject: [PATCH v2 04/10] ARM: mvebu: clearfog: add EEPROM devices In-Reply-To: References: Message-ID: <12bcb02a299239e62a54858711e9aa5a759cd91a.1579522639.git.baruch@tkos.co.il> Add device-tree description for the EEPROM devices on Armada 388 SOM rev 2.1. Another EEPROM is now on Clearfog Pro carrier rev 2.2, and Clearfog Base rev 1.3. Reviewed-by: Stefan Roese Signed-off-by: Baruch Siach --- arch/arm/dts/armada-388-clearfog-u-boot.dtsi | 12 ++++++++++++ arch/arm/dts/armada-388-clearfog.dts | 6 ++++++ arch/arm/dts/armada-38x-solidrun-microsom.dtsi | 8 ++++++++ 3 files changed, 26 insertions(+) diff --git a/arch/arm/dts/armada-388-clearfog-u-boot.dtsi b/arch/arm/dts/armada-388-clearfog-u-boot.dtsi index 9c694089454f..0befcdae298a 100644 --- a/arch/arm/dts/armada-388-clearfog-u-boot.dtsi +++ b/arch/arm/dts/armada-388-clearfog-u-boot.dtsi @@ -24,3 +24,15 @@ &ahci1 { u-boot,dm-spl; }; + +&i2c0 { + u-boot,dm-spl; + + eeprom at 52 { + u-boot,dm-spl; + }; + + eeprom at 53 { + u-boot,dm-spl; + }; +}; diff --git a/arch/arm/dts/armada-388-clearfog.dts b/arch/arm/dts/armada-388-clearfog.dts index 4ddeaa02f122..e4164f49b24d 100644 --- a/arch/arm/dts/armada-388-clearfog.dts +++ b/arch/arm/dts/armada-388-clearfog.dts @@ -259,6 +259,12 @@ compatible = "microchip,mcp3021"; reg = <0x4c>; }; + + eeprom at 52 { + compatible = "atmel,24c02"; + reg = <0x52>; + pagesize = <16>; + }; }; &i2c1 { diff --git a/arch/arm/dts/armada-38x-solidrun-microsom.dtsi b/arch/arm/dts/armada-38x-solidrun-microsom.dtsi index a2627223ce3b..a322a28c215c 100644 --- a/arch/arm/dts/armada-38x-solidrun-microsom.dtsi +++ b/arch/arm/dts/armada-38x-solidrun-microsom.dtsi @@ -99,3 +99,11 @@ status = "okay"; u-boot,dm-pre-reloc; }; + +&i2c0 { + eeprom at 53 { + compatible = "atmel,24c02"; + reg = <0x53>; + pagesize = <16>; + }; +}; From patchwork Mon Jan 20 12:20:10 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Baruch Siach X-Patchwork-Id: 239812 List-Id: U-Boot discussion From: baruch at tkos.co.il (Baruch Siach) Date: Mon, 20 Jan 2020 14:20:10 +0200 Subject: [PATCH v2 05/10] ARM: mvebu: clearfog: add support for EEPROM TLV info In-Reply-To: References: Message-ID: <2edab07b61fdab3a78f0caf4817adc784fa8e29b.1579522639.git.baruch@tkos.co.il> Signed-off-by: Baruch Siach Reviewed-by: Stefan Roese --- configs/clearfog_defconfig | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/configs/clearfog_defconfig b/configs/clearfog_defconfig index 28ce0715926f..e2399a97391d 100644 --- a/configs/clearfog_defconfig +++ b/configs/clearfog_defconfig @@ -28,6 +28,8 @@ CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_DATA_PART_OFFSET=0x1 CONFIG_SPL_I2C_SUPPORT=y +CONFIG_CMD_TLV_EEPROM=y +CONFIG_SPL_CMD_TLV_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_GPIO=y CONFIG_CMD_I2C=y @@ -49,6 +51,8 @@ CONFIG_DM_GPIO=y CONFIG_DM_PCA953X=y CONFIG_DM_I2C=y CONFIG_SYS_I2C_MVTWSI=y +CONFIG_I2C_EEPROM=y +CONFIG_SPL_I2C_EEPROM=y CONFIG_DM_MMC=y CONFIG_SUPPORT_EMMC_BOOT=y CONFIG_MMC_SDHCI=y From patchwork Mon Jan 20 12:20:11 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Baruch Siach X-Patchwork-Id: 239811 List-Id: U-Boot discussion From: baruch at tkos.co.il (Baruch Siach) Date: Mon, 20 Jan 2020 14:20:11 +0200 Subject: [PATCH v2 06/10] ARM: mvebu: clearfog: read basic TLV data In-Reply-To: References: Message-ID: Read RAM die capacity from the EEPROM TLV. Follow the ONIE standard that defines the Vendor Extension entry type for vendor specific data. We have no Private Enterprise Number at the moment as the standard requires. Use the dummy all 0xff value for now. Signed-off-by: Baruch Siach Reviewed-by: Stefan Roese --- board/solidrun/clearfog/clearfog.c | 28 ++++++++ board/solidrun/common/Makefile | 5 ++ board/solidrun/common/tlv_data.c | 102 +++++++++++++++++++++++++++++ board/solidrun/common/tlv_data.h | 18 +++++ 4 files changed, 153 insertions(+) create mode 100644 board/solidrun/common/Makefile create mode 100644 board/solidrun/common/tlv_data.c create mode 100644 board/solidrun/common/tlv_data.h diff --git a/board/solidrun/clearfog/clearfog.c b/board/solidrun/clearfog/clearfog.c index 8b6381194688..39a24aa69ae8 100644 --- a/board/solidrun/clearfog/clearfog.c +++ b/board/solidrun/clearfog/clearfog.c @@ -10,6 +10,7 @@ #include #include #include +#include "../common/tlv_data.h" #include "../drivers/ddr/marvell/a38x/ddr3_init.h" #include <../serdes/a38x/high_speed_env_spec.h> @@ -28,6 +29,19 @@ DECLARE_GLOBAL_DATA_PTR; #define BOARD_GPP_POL_LOW 0x0 #define BOARD_GPP_POL_MID 0x0 +static struct tlv_data cf_tlv_data; + +static void cf_read_tlv_data(void) +{ + static bool read_once; + + if (read_once) + return; + read_once = true; + + read_tlv_data(&cf_tlv_data); +} + static struct serdes_map board_serdes_map[] = { {SATA0, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0}, {SGMII1, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0}, @@ -76,6 +90,20 @@ static struct mv_ddr_topology_map board_topology_map = { struct mv_ddr_topology_map *mv_ddr_topology_map_get(void) { + struct if_params *ifp = &board_topology_map.interface_params[0]; + + cf_read_tlv_data(); + + switch (cf_tlv_data.ram_size) { + case 4: + default: + ifp->memory_size = MV_DDR_DIE_CAP_4GBIT; + break; + case 8: + ifp->memory_size = MV_DDR_DIE_CAP_8GBIT; + break; + } + /* Return the board topology as defined in the board code */ return &board_topology_map; } diff --git a/board/solidrun/common/Makefile b/board/solidrun/common/Makefile new file mode 100644 index 000000000000..a72ac1b7b999 --- /dev/null +++ b/board/solidrun/common/Makefile @@ -0,0 +1,5 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (C) SolidRun + +obj-$(CONFIG_TARGET_CLEARFOG) += tlv_data.o diff --git a/board/solidrun/common/tlv_data.c b/board/solidrun/common/tlv_data.c new file mode 100644 index 000000000000..f08ac8975a6a --- /dev/null +++ b/board/solidrun/common/tlv_data.c @@ -0,0 +1,102 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2020 SolidRun + */ + +#include +#include +#include "tlv_data.h" + +#define SR_TLV_CODE_RAM_SIZE 0x81 + +static void store_product_name(struct tlvinfo_tlv *tlv_entry, + struct tlv_data *td) +{ + int len; + char *dest; + + if (strlen(td->tlv_product_name[0]) == 0) + dest = td->tlv_product_name[0]; + else if (strlen(td->tlv_product_name[1]) == 0) + dest = td->tlv_product_name[1]; + else + return; + + len = min_t(unsigned int, tlv_entry->length, + sizeof(td->tlv_product_name[0]) - 1); + memcpy(dest, tlv_entry->value, len); +} + +static void parse_tlv_vendor_ext(struct tlvinfo_tlv *tlv_entry, + struct tlv_data *td) +{ + u8 *val = tlv_entry->value; + u32 pen; /* IANA Private Enterprise Numbers */ + + if (tlv_entry->length < 5) /* 4 bytes PEN + at least 1 byte type */ + return; + + /* PEN is big endian */ + pen = (val[0] << 24) | (val[1] << 16) | (val[2] << 8) | val[3]; + /* Not a real PEN */ + if (pen != 0xffffffff) + return; + + if (val[4] != SR_TLV_CODE_RAM_SIZE) + return; + if (tlv_entry->length != 6) + return; + td->ram_size = val[5]; +} + +static void parse_tlv_data(u8 *eeprom, struct tlvinfo_header *hdr, + struct tlvinfo_tlv *entry, struct tlv_data *td) +{ + unsigned int tlv_offset, tlv_len; + + tlv_offset = sizeof(struct tlvinfo_header); + tlv_len = sizeof(struct tlvinfo_header) + be16_to_cpu(hdr->totallen); + while (tlv_offset < tlv_len) { + entry = (struct tlvinfo_tlv *)&eeprom[tlv_offset]; + + switch (entry->type) { + case TLV_CODE_PRODUCT_NAME: + store_product_name(entry, td); + break; + case TLV_CODE_VENDOR_EXT: + parse_tlv_vendor_ext(entry, td); + break; + default: + break; + } + + tlv_offset += sizeof(struct tlvinfo_tlv) + entry->length; + } +} + +void read_tlv_data(struct tlv_data *td) +{ + u8 eeprom_data[TLV_TOTAL_LEN_MAX]; + struct tlvinfo_header *tlv_hdr; + struct tlvinfo_tlv *tlv_entry; + int ret, i; + + for (i = 0; i < 2; i++) { + ret = read_tlvinfo_tlv_eeprom(eeprom_data, &tlv_hdr, + &tlv_entry, i); + if (ret < 0) + continue; + parse_tlv_data(eeprom_data, tlv_hdr, tlv_entry, td); + } +} + +bool sr_product_is(const struct tlv_data *td, const char *product) +{ + /* Allow prefix sub-string match */ + if (strncmp(td->tlv_product_name[0], product, strlen(product)) == 0) + return true; + if (strncmp(td->tlv_product_name[1], product, strlen(product)) == 0) + return true; + + return false; +} diff --git a/board/solidrun/common/tlv_data.h b/board/solidrun/common/tlv_data.h new file mode 100644 index 000000000000..a1432e4b8e1d --- /dev/null +++ b/board/solidrun/common/tlv_data.h @@ -0,0 +1,18 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2020 SolidRun + */ + +#ifndef __BOARD_SR_COMMON_H_ +#define __BOARD_SR_COMMON_H_ + +struct tlv_data { + /* Store product name of both SOM and carrier */ + char tlv_product_name[2][32]; + unsigned int ram_size; +}; + +void read_tlv_data(struct tlv_data *td); +bool sr_product_is(const struct tlv_data *td, const char *product); + +#endif /* __BOARD_SR_COMMON_H_ */ From patchwork Mon Jan 20 12:20:12 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Baruch Siach X-Patchwork-Id: 239814 List-Id: U-Boot discussion From: baruch at tkos.co.il (Baruch Siach) Date: Mon, 20 Jan 2020 14:20:12 +0200 Subject: [PATCH v2 07/10] ARM: mvebu: clearfog: print TLV stored product name In-Reply-To: References: Message-ID: Use the data from EEPROM TLV to display the board identity. Reviewed-by: Stefan Roese Signed-off-by: Baruch Siach --- board/solidrun/clearfog/clearfog.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-) diff --git a/board/solidrun/clearfog/clearfog.c b/board/solidrun/clearfog/clearfog.c index 39a24aa69ae8..8050cca55ab7 100644 --- a/board/solidrun/clearfog/clearfog.c +++ b/board/solidrun/clearfog/clearfog.c @@ -156,7 +156,16 @@ int board_init(void) int checkboard(void) { - puts("Board: SolidRun ClearFog\n"); + char *board = "ClearFog"; + + cf_read_tlv_data(); + if (strlen(cf_tlv_data.tlv_product_name[0]) > 0) + board = cf_tlv_data.tlv_product_name[0]; + + printf("Board: SolidRun %s", board); + if (strlen(cf_tlv_data.tlv_product_name[1]) > 0) + printf(", %s", cf_tlv_data.tlv_product_name[1]); + puts("\n"); return 0; } From patchwork Mon Jan 20 12:20:13 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Baruch Siach X-Patchwork-Id: 239815 List-Id: U-Boot discussion From: baruch at tkos.co.il (Baruch Siach) Date: Mon, 20 Jan 2020 14:20:13 +0200 Subject: [PATCH v2 08/10] ARM: mvebu: clearfog: run-time selection of DT file In-Reply-To: References: Message-ID: Set the kernel device-tree file (fdtfile environment variable) based on run-time detection of the platform. Reviewed-by: Stefan Roese Signed-off-by: Baruch Siach --- arch/arm/mach-mvebu/Kconfig | 1 + board/solidrun/clearfog/clearfog.c | 14 ++++++++++++++ 2 files changed, 15 insertions(+) diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig index fdd39685b75d..bc5eaa5a7679 100644 --- a/arch/arm/mach-mvebu/Kconfig +++ b/arch/arm/mach-mvebu/Kconfig @@ -91,6 +91,7 @@ choice config TARGET_CLEARFOG bool "Support ClearFog" select 88F6820 + select BOARD_LATE_INIT config TARGET_HELIOS4 bool "Support Helios4" diff --git a/board/solidrun/clearfog/clearfog.c b/board/solidrun/clearfog/clearfog.c index 8050cca55ab7..e178b06cd34d 100644 --- a/board/solidrun/clearfog/clearfog.c +++ b/board/solidrun/clearfog/clearfog.c @@ -175,3 +175,17 @@ int board_eth_init(bd_t *bis) cpu_eth_init(bis); /* Built in controller(s) come first */ return pci_eth_init(bis); } + +int board_late_init(void) +{ + cf_read_tlv_data(); + + if (sr_product_is(&cf_tlv_data, "Clearfog Base")) + env_set("fdtfile", "armada-388-clearfog-base.dtb"); + else if (sr_product_is(&cf_tlv_data, "Clearfog GTR S4")) + env_set("fdtfile", "armada-385-clearfog-gtr-s4.dtb"); + else if (sr_product_is(&cf_tlv_data, "Clearfog GTR L8")) + env_set("fdtfile", "armada-385-clearfog-gtr-l8.dtb"); + + return 0; +} From patchwork Mon Jan 20 12:20:14 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Baruch Siach X-Patchwork-Id: 239817 List-Id: U-Boot discussion From: baruch at tkos.co.il (Baruch Siach) Date: Mon, 20 Jan 2020 14:20:14 +0200 Subject: [PATCH v2 09/10] ARM: mvebu: clearfog: add Clearfog GTR support In-Reply-To: References: Message-ID: <1f1136233d7e05cbd89cd72c9080062f22fd11b4.1579522639.git.baruch@tkos.co.il> Select the serdes configuration table based on the platform identity read from EEPROM TLV data. Clearfog GTR needs a slightly different serdes configuration. Reviewed-by: Stefan Roese Signed-off-by: Baruch Siach --- board/solidrun/clearfog/clearfog.c | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/board/solidrun/clearfog/clearfog.c b/board/solidrun/clearfog/clearfog.c index e178b06cd34d..3bc9ce0839a9 100644 --- a/board/solidrun/clearfog/clearfog.c +++ b/board/solidrun/clearfog/clearfog.c @@ -53,6 +53,14 @@ static struct serdes_map board_serdes_map[] = { int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count) { + cf_read_tlv_data(); + + if (sr_product_is(&cf_tlv_data, "Clearfog GTR")) { + board_serdes_map[0].serdes_type = PEX0; + board_serdes_map[0].serdes_speed = SERDES_SPEED_5_GBPS; + board_serdes_map[0].serdes_mode = PEX_ROOT_COMPLEX_X1; + } + *serdes_map_array = board_serdes_map; *count = ARRAY_SIZE(board_serdes_map); return 0; From patchwork Mon Jan 20 12:20:15 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Baruch Siach X-Patchwork-Id: 239816 List-Id: U-Boot discussion From: baruch at tkos.co.il (Baruch Siach) Date: Mon, 20 Jan 2020 14:20:15 +0200 Subject: [PATCH v2 10/10] ARM: mvebu: clearfog: add Clearfog Base serdes configuration In-Reply-To: References: Message-ID: <9267eb70635b6dc8c296843e4f3d4302c978ffee.1579522639.git.baruch@tkos.co.il> Clearfog Base carrier uses serdes lane #5 as USB host. Use EEPROM stored device identification to configure the serdes accordingly when available. Reviewed-by: Stefan Roese Signed-off-by: Baruch Siach --- board/solidrun/clearfog/clearfog.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/board/solidrun/clearfog/clearfog.c b/board/solidrun/clearfog/clearfog.c index 3bc9ce0839a9..e268ef55a2a0 100644 --- a/board/solidrun/clearfog/clearfog.c +++ b/board/solidrun/clearfog/clearfog.c @@ -61,6 +61,12 @@ int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count) board_serdes_map[0].serdes_mode = PEX_ROOT_COMPLEX_X1; } + if (sr_product_is(&cf_tlv_data, "Clearfog Base")) { + board_serdes_map[4].serdes_type = USB3_HOST0; + board_serdes_map[4].serdes_speed = SERDES_SPEED_5_GBPS; + board_serdes_map[4].serdes_mode = SERDES_DEFAULT_MODE; + } + *serdes_map_array = board_serdes_map; *count = ARRAY_SIZE(board_serdes_map); return 0;