From patchwork Fri Apr 24 16:50:03 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: "Sylwester Nawrocki/Kernel \\\(PLT\\\) /SRPOL/Staff Engineer/Samsung Electronics" X-Patchwork-Id: 238414 List-Id: U-Boot discussion From: s.nawrocki at samsung.com (Sylwester Nawrocki) Date: Fri, 24 Apr 2020 18:50:03 +0200 Subject: [PATCH v1 01/10] usb: xhci: Add missing cache flush in the scratchpad array initialization In-Reply-To: <20200424165012.31915-1-s.nawrocki@samsung.com> References: <20200424165012.31915-1-s.nawrocki@samsung.com> Message-ID: <20200424165012.31915-2-s.nawrocki@samsung.com> In current code there is no cache flush after initializing the scratchpad buffer array with the scratchpad buffer pointers. This leads to a failure of the "slot enable" command on the rpi4 board (Broadcom STB PCIe controller + VL805 USB hub) - the very first TRB transfer on the command ring fails and there is a timeout while waiting for the command completion event. After adding the missing cache flush everything seems to be working as expected. Reviewed-by: Bin Meng Signed-off-by: Sylwester Nawrocki Reviewed-by: Nicolas Saenz Julienne --- Changes since RFC: - none. --- drivers/usb/host/xhci-mem.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index 93450ee..729bdc3 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -393,6 +393,9 @@ static int xhci_scratchpad_alloc(struct xhci_ctrl *ctrl) scratchpad->sp_array[i] = cpu_to_le64(ptr); } + xhci_flush_cache((uintptr_t)scratchpad->sp_array, + sizeof(u64) * num_sp); + return 0; fail_sp3: From patchwork Fri Apr 24 16:50:04 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: "Sylwester Nawrocki/Kernel \\\(PLT\\\) /SRPOL/Staff Engineer/Samsung Electronics" X-Patchwork-Id: 238415 List-Id: U-Boot discussion From: s.nawrocki at samsung.com (Sylwester Nawrocki) Date: Fri, 24 Apr 2020 18:50:04 +0200 Subject: [PATCH v1 02/10] usb: xhci: Use only 32-bit accesses in xhci_writeq/xhci_readq In-Reply-To: <20200424165012.31915-1-s.nawrocki@samsung.com> References: <20200424165012.31915-1-s.nawrocki@samsung.com> Message-ID: <20200424165012.31915-3-s.nawrocki@samsung.com> There might be hardware configurations where 64-bit data accesses to XHCI registers are not supported properly. This patch removes the readq/writeq so always two 32-bit accesses are used to read/write 64-bit XHCI registers, similarly as it is done in Linux kernel. This patch fixes operation of the XHCI controller on RPI4 Broadcom BCM2711 SoC based board, where the VL805 USB XHCI controller is connected to the PCIe Root Complex, which is attached to the system through the SCB bridge. Even though the architecture is 64-bit the PCIe BAR is 32-bit and likely the 64-bit wide register accesses initiated by the CPU are not properly translated to a sequence of 32-bit PCIe accesses. xhci_readq(), for example, always returns same value in upper and lower 32-bits, e.g. 0xabcd1234abcd1234 instead of 0x00000000abcd1234. Cc: Sergey Temerkhanov Signed-off-by: Sylwester Nawrocki Reviewed-by: Bin Meng Reviewed-by: Nicolas Saenz Julienne --- Changes since RFC: - dropped Kconfig option, switched to not using readq/writeq unconditionally. --- include/usb/xhci.h | 8 -------- 1 file changed, 8 deletions(-) diff --git a/include/usb/xhci.h b/include/usb/xhci.h index 6017504..c16106a 100644 --- a/include/usb/xhci.h +++ b/include/usb/xhci.h @@ -1111,28 +1111,20 @@ static inline void xhci_writel(uint32_t volatile *regs, const unsigned int val) */ static inline u64 xhci_readq(__le64 volatile *regs) { -#if BITS_PER_LONG == 64 - return readq(regs); -#else __u32 *ptr = (__u32 *)regs; u64 val_lo = readl(ptr); u64 val_hi = readl(ptr + 1); return val_lo + (val_hi << 32); -#endif } static inline void xhci_writeq(__le64 volatile *regs, const u64 val) { -#if BITS_PER_LONG == 64 - writeq(val, regs); -#else __u32 *ptr = (__u32 *)regs; u32 val_lo = lower_32_bits(val); /* FIXME */ u32 val_hi = upper_32_bits(val); writel(val_lo, ptr); writel(val_hi, ptr + 1); -#endif } int xhci_hcd_init(int index, struct xhci_hccr **ret_hccr, From patchwork Fri Apr 24 16:50:05 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: "Sylwester Nawrocki/Kernel \\\(PLT\\\) /SRPOL/Staff Engineer/Samsung Electronics" X-Patchwork-Id: 238416 List-Id: U-Boot discussion From: s.nawrocki at samsung.com (Sylwester Nawrocki) Date: Fri, 24 Apr 2020 18:50:05 +0200 Subject: [PATCH v1 03/10] pci: Move some PCIe register offset definitions to a common header In-Reply-To: <20200424165012.31915-1-s.nawrocki@samsung.com> References: <20200424165012.31915-1-s.nawrocki@samsung.com> Message-ID: <20200424165012.31915-4-s.nawrocki@samsung.com> Some PCI Express register offsets are currently defined in multiple drivers, move them to a common header to avoid re-definitions and as a pre-requisite for adding new PCIe driver. While at it replace some spaces with tabs. Reviewed-by: Bin Meng Signed-off-by: Sylwester Nawrocki Reviewed-by: Nicolas Saenz Julienne --- Changes since RFC: - whitespace clean up. --- drivers/pci/pci-rcar-gen3.c | 8 -------- drivers/pci/pcie_intel_fpga.c | 3 --- include/pci.h | 13 +++++++++++-- 3 files changed, 11 insertions(+), 13 deletions(-) diff --git a/drivers/pci/pci-rcar-gen3.c b/drivers/pci/pci-rcar-gen3.c index 30eff67..393f1c9 100644 --- a/drivers/pci/pci-rcar-gen3.c +++ b/drivers/pci/pci-rcar-gen3.c @@ -117,14 +117,6 @@ #define RCAR_PCI_MAX_RESOURCES 4 #define MAX_NR_INBOUND_MAPS 6 -#define PCI_EXP_FLAGS 2 /* Capabilities register */ -#define PCI_EXP_FLAGS_TYPE 0x00f0 /* Device/Port type */ -#define PCI_EXP_TYPE_ROOT_PORT 0x4 /* Root Port */ -#define PCI_EXP_LNKCAP 12 /* Link Capabilities */ -#define PCI_EXP_LNKCAP_DLLLARC 0x00100000 /* Data Link Layer Link Active Reporting Capable */ -#define PCI_EXP_SLTCAP 20 /* Slot Capabilities */ -#define PCI_EXP_SLTCAP_PSN 0xfff80000 /* Physical Slot Number */ - enum { RCAR_PCI_ACCESS_READ, RCAR_PCI_ACCESS_WRITE, diff --git a/drivers/pci/pcie_intel_fpga.c b/drivers/pci/pcie_intel_fpga.c index 6a9f29c..69363a0 100644 --- a/drivers/pci/pcie_intel_fpga.c +++ b/drivers/pci/pcie_intel_fpga.c @@ -65,9 +65,6 @@ #define IS_ROOT_PORT(pcie, bdf) \ ((PCI_BUS(bdf) == pcie->first_busno) ? true : false) -#define PCI_EXP_LNKSTA 18 /* Link Status */ -#define PCI_EXP_LNKSTA_DLLLA 0x2000 /* Data Link Layer Link Active */ - /** * struct intel_fpga_pcie - Intel FPGA PCIe controller state * @bus: Pointer to the PCI bus diff --git a/include/pci.h b/include/pci.h index 174ddd4..5bf91a4 100644 --- a/include/pci.h +++ b/include/pci.h @@ -471,10 +471,19 @@ #define PCI_EA_FIELD_MASK 0xfffffffc /* For Base & Max Offset */ /* PCI Express capabilities */ +#define PCI_EXP_FLAGS 2 /* Capabilities register */ +#define PCI_EXP_FLAGS_TYPE 0x00f0 /* Device/Port type */ +#define PCI_EXP_TYPE_ROOT_PORT 0x4 /* Root Port */ #define PCI_EXP_DEVCAP 4 /* Device capabilities */ -#define PCI_EXP_DEVCAP_FLR 0x10000000 /* Function Level Reset */ +#define PCI_EXP_DEVCAP_FLR 0x10000000 /* Function Level Reset */ #define PCI_EXP_DEVCTL 8 /* Device Control */ -#define PCI_EXP_DEVCTL_BCR_FLR 0x8000 /* Bridge Configuration Retry / FLR */ +#define PCI_EXP_DEVCTL_BCR_FLR 0x8000 /* Bridge Configuration Retry / FLR */ +#define PCI_EXP_LNKCAP 12 /* Link Capabilities */ +#define PCI_EXP_LNKCAP_DLLLARC 0x00100000 /* Data Link Layer Link Active Reporting Capable */ +#define PCI_EXP_LNKSTA 18 /* Link Status */ +#define PCI_EXP_LNKSTA_DLLLA 0x2000 /* Data Link Layer Link Active */ +#define PCI_EXP_SLTCAP 20 /* Slot Capabilities */ +#define PCI_EXP_SLTCAP_PSN 0xfff80000 /* Physical Slot Number */ /* Include the ID list */ From patchwork Fri Apr 24 16:50:06 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: "Sylwester Nawrocki/Kernel \\\(PLT\\\) /SRPOL/Staff Engineer/Samsung Electronics" X-Patchwork-Id: 238417 List-Id: U-Boot discussion From: s.nawrocki at samsung.com (Sylwester Nawrocki) Date: Fri, 24 Apr 2020 18:50:06 +0200 Subject: [PATCH v1 04/10] rpi4: shorten a mapping for the DRAM In-Reply-To: <20200424165012.31915-1-s.nawrocki@samsung.com> References: <20200424165012.31915-1-s.nawrocki@samsung.com> Message-ID: <20200424165012.31915-5-s.nawrocki@samsung.com> From: Marek Szyprowski Remove the overlap between DRAM and device's IO area. Signed-off-by: Marek Szyprowski Reviewed-by: Nicolas Saenz Julienne --- Changes since RFC: - none. --- arch/arm/mach-bcm283x/init.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/mach-bcm283x/init.c b/arch/arm/mach-bcm283x/init.c index 9966d6c..4295356 100644 --- a/arch/arm/mach-bcm283x/init.c +++ b/arch/arm/mach-bcm283x/init.c @@ -38,7 +38,7 @@ static struct mm_region bcm2711_mem_map[] = { { .virt = 0x00000000UL, .phys = 0x00000000UL, - .size = 0xfe000000UL, + .size = 0xfc000000UL, .attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) | PTE_BLOCK_INNER_SHARE }, { From patchwork Fri Apr 24 16:50:07 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: "Sylwester Nawrocki/Kernel \\\(PLT\\\) /SRPOL/Staff Engineer/Samsung Electronics" X-Patchwork-Id: 238418 List-Id: U-Boot discussion From: s.nawrocki at samsung.com (Sylwester Nawrocki) Date: Fri, 24 Apr 2020 18:50:07 +0200 Subject: [PATCH v1 05/10] rpi4: add a mapping for the PCIe XHCI controller MMIO registers (ARM 64bit) In-Reply-To: <20200424165012.31915-1-s.nawrocki@samsung.com> References: <20200424165012.31915-1-s.nawrocki@samsung.com> Message-ID: <20200424165012.31915-6-s.nawrocki@samsung.com> From: Marek Szyprowski Create a non-cacheable mapping for the 0x600000000 physical memory region, where MMIO registers for the PCIe XHCI controller are instantiated by the PCIe bridge. Signed-off-by: Marek Szyprowski Reviewed-by: Nicolas Saenz Julienne --- Changes since RFC: - none. --- arch/arm/mach-bcm283x/init.c | 18 +++++++++++++++--- 1 file changed, 15 insertions(+), 3 deletions(-) diff --git a/arch/arm/mach-bcm283x/init.c b/arch/arm/mach-bcm283x/init.c index 4295356..6a748da 100644 --- a/arch/arm/mach-bcm283x/init.c +++ b/arch/arm/mach-bcm283x/init.c @@ -11,10 +11,15 @@ #include #include +#define BCM2711_RPI4_PCIE_XHCI_MMIO_PHYS 0x600000000UL +#define BCM2711_RPI4_PCIE_XHCI_MMIO_SIZE 0x800000UL + #ifdef CONFIG_ARM64 #include -static struct mm_region bcm283x_mem_map[] = { +#define MAX_MAP_MAX_ENTRIES (4) + +static struct mm_region bcm283x_mem_map[MAX_MAP_MAX_ENTRIES] = { { .virt = 0x00000000UL, .phys = 0x00000000UL, @@ -34,7 +39,7 @@ static struct mm_region bcm283x_mem_map[] = { } }; -static struct mm_region bcm2711_mem_map[] = { +static struct mm_region bcm2711_mem_map[MAX_MAP_MAX_ENTRIES] = { { .virt = 0x00000000UL, .phys = 0x00000000UL, @@ -49,6 +54,13 @@ static struct mm_region bcm2711_mem_map[] = { PTE_BLOCK_NON_SHARE | PTE_BLOCK_PXN | PTE_BLOCK_UXN }, { + .virt = BCM2711_RPI4_PCIE_XHCI_MMIO_PHYS, + .phys = BCM2711_RPI4_PCIE_XHCI_MMIO_PHYS, + .size = BCM2711_RPI4_PCIE_XHCI_MMIO_SIZE, + .attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) | + PTE_BLOCK_NON_SHARE | + PTE_BLOCK_PXN | PTE_BLOCK_UXN + }, { /* List terminator */ 0, } @@ -71,7 +83,7 @@ static void _rpi_update_mem_map(struct mm_region *pd) { int i; - for (i = 0; i < 2; i++) { + for (i = 0; i < MAX_MAP_MAX_ENTRIES; i++) { mem_map[i].virt = pd[i].virt; mem_map[i].phys = pd[i].phys; mem_map[i].size = pd[i].size; From patchwork Fri Apr 24 16:50:08 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: "Sylwester Nawrocki/Kernel \\\(PLT\\\) /SRPOL/Staff Engineer/Samsung Electronics" X-Patchwork-Id: 238421 List-Id: U-Boot discussion From: s.nawrocki at samsung.com (Sylwester Nawrocki) Date: Fri, 24 Apr 2020 18:50:08 +0200 Subject: [PATCH v1 06/10] rpi4: add a mapping for the PCIe XHCI controller MMIO registers (ARM 32bit) In-Reply-To: <20200424165012.31915-1-s.nawrocki@samsung.com> References: <20200424165012.31915-1-s.nawrocki@samsung.com> Message-ID: <20200424165012.31915-7-s.nawrocki@samsung.com> From: Marek Szyprowski Create a non-cacheable mapping for the 0x600000000 physical memory region, where MMIO registers for the PCIe XHCI controller are instantiated by the PCIe bridge. Due to 32bit limit in the CPU virtual address space in ARM 32bit mode, this region is mapped at 0xff800000 CPU virtual address. Signed-off-by: Marek Szyprowski --- Changes since RFC: - none. --- arch/arm/mach-bcm283x/Kconfig | 1 + arch/arm/mach-bcm283x/include/mach/base.h | 7 +++++ arch/arm/mach-bcm283x/init.c | 52 +++++++++++++++++++++++++++++++ 3 files changed, 60 insertions(+) diff --git a/arch/arm/mach-bcm283x/Kconfig b/arch/arm/mach-bcm283x/Kconfig index 00419bf..bcb7f1d 100644 --- a/arch/arm/mach-bcm283x/Kconfig +++ b/arch/arm/mach-bcm283x/Kconfig @@ -36,6 +36,7 @@ config BCM2711_32B select BCM2711 select ARMV7_LPAE select CPU_V7A + select PHYS_64BIT config BCM2711_64B bool "Broadcom BCM2711 SoC 64-bit support" diff --git a/arch/arm/mach-bcm283x/include/mach/base.h b/arch/arm/mach-bcm283x/include/mach/base.h index c4ae398..1d10dc9 100644 --- a/arch/arm/mach-bcm283x/include/mach/base.h +++ b/arch/arm/mach-bcm283x/include/mach/base.h @@ -6,6 +6,13 @@ #ifndef _BCM283x_BASE_H_ #define _BCM283x_BASE_H_ +#include + extern unsigned long rpi_bcm283x_base; +#ifdef CONFIG_ARMV7_LPAE +extern void *rpi4_phys_to_virt(phys_addr_t paddr); +#define phys_to_virt(x) rpi4_phys_to_virt(x) +#endif + #endif diff --git a/arch/arm/mach-bcm283x/init.c b/arch/arm/mach-bcm283x/init.c index 6a748da..5d0d160 100644 --- a/arch/arm/mach-bcm283x/init.c +++ b/arch/arm/mach-bcm283x/init.c @@ -145,6 +145,58 @@ int mach_cpu_init(void) } #ifdef CONFIG_ARMV7_LPAE + +#define BCM2711_RPI4_PCIE_XHCI_MMIO_VIRT 0xff800000UL + +void *rpi4_phys_to_virt(phys_addr_t paddr) +{ + if (paddr >= BCM2711_RPI4_PCIE_XHCI_MMIO_PHYS) + paddr = paddr - BCM2711_RPI4_PCIE_XHCI_MMIO_PHYS + + BCM2711_RPI4_PCIE_XHCI_MMIO_VIRT; + return (void *)(unsigned long)paddr; +} + +static void set_section_phys(unsigned int section, phys_addr_t phys, + enum dcache_option option) +{ + u64 *page_table = (u64 *)gd->arch.tlb_addr; + /* Need to set the access flag to not fault */ + u64 value = TTB_SECT_AP | TTB_SECT_AF; + + /* Add the page offset */ + value |= (phys); + + /* Add caching bits */ + value |= option; + + /* Set PTE */ + page_table[section] = value; +} + +static void rpi4_create_pcie_xhci_mapping(void) +{ + unsigned sect = BCM2711_RPI4_PCIE_XHCI_MMIO_VIRT >> MMU_SECTION_SHIFT; + phys_addr_t phys_addr = BCM2711_RPI4_PCIE_XHCI_MMIO_PHYS; + unsigned int size = BCM2711_RPI4_PCIE_XHCI_MMIO_SIZE; + + while (size) { + set_section_phys(sect, phys_addr, DCACHE_OFF); + sect++; + phys_addr += MMU_SECTION_SIZE; + size -= MMU_SECTION_SIZE; + } +} + +void arm_init_domains(void) +{ + /* + * Hijack this function to prepare a mappings for the PCIe MMIO + * region for the XHCI controller on RPi4 board. + * This code is called before enabling the MMU in ARM 32bit mode. + */ + rpi4_create_pcie_xhci_mapping(); +} + void enable_caches(void) { dcache_enable(); From patchwork Fri Apr 24 16:50:09 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: "Sylwester Nawrocki/Kernel \\\(PLT\\\) /SRPOL/Staff Engineer/Samsung Electronics" X-Patchwork-Id: 238419 List-Id: U-Boot discussion From: s.nawrocki at samsung.com (Sylwester Nawrocki) Date: Fri, 24 Apr 2020 18:50:09 +0200 Subject: [PATCH v1 07/10] linux/bitfield.h: Add primitives for manipulating bitfields both in host- and fixed-endian. In-Reply-To: <20200424165012.31915-1-s.nawrocki@samsung.com> References: <20200424165012.31915-1-s.nawrocki@samsung.com> Message-ID: <20200424165012.31915-8-s.nawrocki@samsung.com> From: Nicolas Saenz Julienne Imports Al Viro's original Linux commit 00b0c9b82663a, which contains an in depth explanation and two fixes from Johannes Berg: e7d4a95da86e0 "bitfield: fix *_encode_bits()", 37a3862e12382 "bitfield: add u8 helpers". Signed-off-by: Nicolas Saenz Julienne Signed-off-by: Sylwester Nawrocki --- Changes since RFC: - new patch. --- include/linux/bitfield.h | 46 ++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 46 insertions(+) diff --git a/include/linux/bitfield.h b/include/linux/bitfield.h index 8b9d6ff..4964213 100644 --- a/include/linux/bitfield.h +++ b/include/linux/bitfield.h @@ -103,4 +103,50 @@ (typeof(_mask))(((_reg) & (_mask)) >> __bf_shf(_mask)); \ }) +extern void __compiletime_error("value doesn't fit into mask") +__field_overflow(void); +extern void __compiletime_error("bad bitfield mask") +__bad_mask(void); +static __always_inline u64 field_multiplier(u64 field) +{ + if ((field | (field - 1)) & ((field | (field - 1)) + 1)) + __bad_mask(); + return field & -field; +} +static __always_inline u64 field_mask(u64 field) +{ + return field / field_multiplier(field); +} +#define ____MAKE_OP(type,base,to,from) \ +static __always_inline __##type type##_encode_bits(base v, base field) \ +{ \ + if (__builtin_constant_p(v) && (v & ~field_mask(field))) \ + __field_overflow(); \ + return to((v & field_mask(field)) * field_multiplier(field)); \ +} \ +static __always_inline __##type type##_replace_bits(__##type old, \ + base val, base field) \ +{ \ + return (old & ~to(field)) | type##_encode_bits(val, field); \ +} \ +static __always_inline void type##p_replace_bits(__##type *p, \ + base val, base field) \ +{ \ + *p = (*p & ~to(field)) | type##_encode_bits(val, field); \ +} \ +static __always_inline base type##_get_bits(__##type v, base field) \ +{ \ + return (from(v) & field)/field_multiplier(field); \ +} +#define __MAKE_OP(size) \ + ____MAKE_OP(le##size,u##size,cpu_to_le##size,le##size##_to_cpu) \ + ____MAKE_OP(be##size,u##size,cpu_to_be##size,be##size##_to_cpu) \ + ____MAKE_OP(u##size,u##size,,) +____MAKE_OP(u8,u8,,) +__MAKE_OP(16) +__MAKE_OP(32) +__MAKE_OP(64) +#undef __MAKE_OP +#undef ____MAKE_OP + #endif From patchwork Fri Apr 24 16:50:10 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: "Sylwester Nawrocki/Kernel \\\(PLT\\\) /SRPOL/Staff Engineer/Samsung Electronics" X-Patchwork-Id: 238420 List-Id: U-Boot discussion From: s.nawrocki at samsung.com (Sylwester Nawrocki) Date: Fri, 24 Apr 2020 18:50:10 +0200 Subject: [PATCH v1 08/10] pci: Add some PCI Express capability register offset definitions In-Reply-To: <20200424165012.31915-1-s.nawrocki@samsung.com> References: <20200424165012.31915-1-s.nawrocki@samsung.com> Message-ID: <20200424165012.31915-9-s.nawrocki@samsung.com> Add PCI Express capability definitions required by the Broadcom STB PCIe controller driver. Reviewed-by: Bin Meng Signed-off-by: Sylwester Nawrocki Reviewed-by: Nicolas Saenz Julienne --- Changes since RFC: - ensure the entries are added in order, sorted by ascending address values. --- include/pci.h | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/include/pci.h b/include/pci.h index 5bf91a4..5307478 100644 --- a/include/pci.h +++ b/include/pci.h @@ -479,11 +479,17 @@ #define PCI_EXP_DEVCTL 8 /* Device Control */ #define PCI_EXP_DEVCTL_BCR_FLR 0x8000 /* Bridge Configuration Retry / FLR */ #define PCI_EXP_LNKCAP 12 /* Link Capabilities */ +#define PCI_EXP_LNKCAP_SLS 0x0000000f /* Supported Link Speeds */ +#define PCI_EXP_LNKCAP_MLW 0x000003f0 /* Maximum Link Width */ #define PCI_EXP_LNKCAP_DLLLARC 0x00100000 /* Data Link Layer Link Active Reporting Capable */ #define PCI_EXP_LNKSTA 18 /* Link Status */ +#define PCI_EXP_LNKSTA_CLS 0x000f /* Current Link Speed */ +#define PCI_EXP_LNKSTA_NLW 0x03f0 /* Negotiated Link Width */ +#define PCI_EXP_LNKSTA_NLW_SHIFT 4 /* start of NLW mask in link status */ #define PCI_EXP_LNKSTA_DLLLA 0x2000 /* Data Link Layer Link Active */ #define PCI_EXP_SLTCAP 20 /* Slot Capabilities */ #define PCI_EXP_SLTCAP_PSN 0xfff80000 /* Physical Slot Number */ +#define PCI_EXP_LNKCTL2 48 /* Link Control 2 */ /* Include the ID list */ From patchwork Fri Apr 24 16:50:11 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: "Sylwester Nawrocki/Kernel \\\(PLT\\\) /SRPOL/Staff Engineer/Samsung Electronics" X-Patchwork-Id: 238422 List-Id: U-Boot discussion From: s.nawrocki at samsung.com (Sylwester Nawrocki) Date: Fri, 24 Apr 2020 18:50:11 +0200 Subject: [PATCH v1 09/10] pci: Add driver for Broadcom STB PCIe controller In-Reply-To: <20200424165012.31915-1-s.nawrocki@samsung.com> References: <20200424165012.31915-1-s.nawrocki@samsung.com> Message-ID: <20200424165012.31915-10-s.nawrocki@samsung.com> This patch adds basic driver for the Broadcom STB PCIe host controller. The code is based on Linux upstream driver (pcie-brcmstb.c) with MSI handling removed. The inbound access memory region is not currently parsed from dma-ranges DT property and a fixed 4GB region is used. The patch has been tested on RPI4 board, i.e. on BCM2711 SoC with VL805 USB Host Controller. Signed-off-by: Nicolas Saenz Julienne Signed-off-by: Sylwester Nawrocki --- Changes since RFC: - reworked to align with current Linux mainline version and u-boot driver by Nicolas Saenz Julienne --- drivers/pci/Kconfig | 6 + drivers/pci/Makefile | 1 + drivers/pci/pcie_brcmstb.c | 593 +++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 600 insertions(+) create mode 100644 drivers/pci/pcie_brcmstb.c diff --git a/drivers/pci/Kconfig b/drivers/pci/Kconfig index 437cd9a..056a021 100644 --- a/drivers/pci/Kconfig +++ b/drivers/pci/Kconfig @@ -197,4 +197,10 @@ config PCIE_MEDIATEK Say Y here if you want to enable Gen2 PCIe controller, which could be found on MT7623 SoC family. +config PCI_BRCMSTB + bool "Broadcom STB PCIe controller" + depends on DM_PCI + depends on ARCH_BCM283X + help + Say Y here if you want to enable Broadcom STB PCIe controller support. endif diff --git a/drivers/pci/Makefile b/drivers/pci/Makefile index c051ecc..3e53b1f 100644 --- a/drivers/pci/Makefile +++ b/drivers/pci/Makefile @@ -43,3 +43,4 @@ obj-$(CONFIG_PCI_PHYTIUM) += pcie_phytium.o obj-$(CONFIG_PCIE_INTEL_FPGA) += pcie_intel_fpga.o obj-$(CONFIG_PCI_KEYSTONE) += pcie_dw_ti.o obj-$(CONFIG_PCIE_MEDIATEK) += pcie_mediatek.o +obj-$(CONFIG_PCI_BRCMSTB) += pcie_brcmstb.o diff --git a/drivers/pci/pcie_brcmstb.c b/drivers/pci/pcie_brcmstb.c new file mode 100644 index 0000000..dfe9833 --- /dev/null +++ b/drivers/pci/pcie_brcmstb.c @@ -0,0 +1,593 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Broadcom STB PCIe controller driver + * + * Copyright (C) 2020 Samsung Electronics Co., Ltd. + * + * Based on upstream Linux kernel driver: + * drivers/pci/controller/pcie-brcmstb.c + * Copyright (C) 2009 - 2017 Broadcom + * + * Based driver by Nicolas Saenz Julienne + * Copyright (C) 2020 Nicolas Saenz Julienne + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +/* BRCM_PCIE_CAP_REGS - Offset for the mandatory capability config regs */ +#define BRCM_PCIE_CAP_REGS 0x00ac + +/* Broadcom STB PCIe Register Offsets */ +#define PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1 0x0188 +#define PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1_ENDIAN_MODE_BAR2_MASK 0xc +#define PCIE_RC_CFG_VENDOR_SPCIFIC_REG1_LITTLE_ENDIAN 0x0 + +#define PCIE_RC_CFG_PRIV1_ID_VAL3 0x043c +#define PCIE_RC_CFG_PRIV1_ID_VAL3_CLASS_CODE_MASK 0xffffff + +#define PCIE_RC_DL_MDIO_ADDR 0x1100 +#define PCIE_RC_DL_MDIO_WR_DATA 0x1104 +#define PCIE_RC_DL_MDIO_RD_DATA 0x1108 + +#define PCIE_MISC_MISC_CTRL 0x4008 +#define PCIE_MISC_MISC_CTRL_SCB_ACCESS_EN_MASK 0x1000 +#define PCIE_MISC_MISC_CTRL_CFG_READ_UR_MODE_MASK 0x2000 +#define PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_MASK 0x300000 +#define PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_128 0x0 +#define PCIE_MISC_MISC_CTRL_SCB0_SIZE_MASK 0xf8000000 + +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LO 0x400c +#define PCIE_MEM_WIN0_LO(win) \ + PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LO + ((win) * 4) + +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_HI 0x4010 +#define PCIE_MEM_WIN0_HI(win) \ + PCIE_MISC_CPU_2_PCIE_MEM_WIN0_HI + ((win) * 4) + +#define PCIE_MISC_RC_BAR1_CONFIG_LO 0x402c +#define PCIE_MISC_RC_BAR1_CONFIG_LO_SIZE_MASK 0x1f + +#define PCIE_MISC_RC_BAR2_CONFIG_LO 0x4034 +#define PCIE_MISC_RC_BAR2_CONFIG_LO_SIZE_MASK 0x1f +#define PCIE_MISC_RC_BAR2_CONFIG_HI 0x4038 + +#define PCIE_MISC_RC_BAR3_CONFIG_LO 0x403c +#define PCIE_MISC_RC_BAR3_CONFIG_LO_SIZE_MASK 0x1f + +#define PCIE_MISC_PCIE_STATUS 0x4068 +#define PCIE_MISC_PCIE_STATUS_PCIE_PORT_MASK 0x80 +#define PCIE_MISC_PCIE_STATUS_PCIE_DL_ACTIVE_MASK 0x20 +#define PCIE_MISC_PCIE_STATUS_PCIE_PHYLINKUP_MASK 0x10 +#define PCIE_MISC_PCIE_STATUS_PCIE_LINK_IN_L23_MASK 0x40 + +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT 0x4070 +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_LIMIT_MASK 0xfff00000 +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_BASE_MASK 0xfff0 +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_BASE_HI_SHIFT 12 +#define PCIE_MEM_WIN0_BASE_LIMIT(win) \ + PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT + ((win) * 4) + +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_HI 0x4080 +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_HI_BASE_MASK 0xff +#define PCIE_MEM_WIN0_BASE_HI(win) \ + PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_HI + ((win) * 8) + +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LIMIT_HI 0x4084 +#define PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LIMIT_HI_LIMIT_MASK 0xff +#define PCIE_MEM_WIN0_LIMIT_HI(win) \ + PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LIMIT_HI + ((win) * 8) + +#define PCIE_MISC_HARD_PCIE_HARD_DEBUG 0x4204 +#define PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK 0x2 +#define PCIE_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK 0x08000000 + +#define PCIE_MSI_INTR2_CLR 0x4508 +#define PCIE_MSI_INTR2_MASK_SET 0x4510 + +#define PCIE_EXT_CFG_DATA 0x8000 + +#define PCIE_EXT_CFG_INDEX 0x9000 +#define PCIE_EXT_BUSNUM_SHIFT 20 +#define PCIE_EXT_SLOT_SHIFT 15 +#define PCIE_EXT_FUNC_SHIFT 12 + +#define PCIE_RGR1_SW_INIT_1 0x9210 +#define PCIE_RGR1_SW_INIT_1_PERST_MASK 0x1 +#define PCIE_RGR1_SW_INIT_1_INIT_MASK 0x2 + +/* PCIe parameters */ +#define BRCM_NUM_PCIE_OUT_WINS 0x4 + +/* MDIO registers */ +#define MDIO_PORT0 0x0 +#define MDIO_DATA_MASK 0x7fffffff +#define MDIO_PORT_MASK 0xf0000 +#define MDIO_REGAD_MASK 0xffff +#define MDIO_CMD_MASK 0xfff00000 +#define MDIO_CMD_READ 0x1 +#define MDIO_CMD_WRITE 0x0 +#define MDIO_DATA_DONE_MASK 0x80000000 +#define MDIO_RD_DONE(x) (((x) & MDIO_DATA_DONE_MASK) ? 1 : 0) +#define MDIO_WT_DONE(x) (((x) & MDIO_DATA_DONE_MASK) ? 0 : 1) +#define SSC_REGS_ADDR 0x1100 +#define SET_ADDR_OFFSET 0x1f +#define SSC_CNTL_OFFSET 0x2 +#define SSC_CNTL_OVRD_EN_MASK 0x8000 +#define SSC_CNTL_OVRD_VAL_MASK 0x4000 +#define SSC_STATUS_OFFSET 0x1 +#define SSC_STATUS_SSC_MASK 0x400 +#define SSC_STATUS_PLL_LOCK_MASK 0x800 + +struct brcm_pcie { + void __iomem *base; + + int gen; + bool ssc; +}; + +#define msleep(a) udelay((a) * 1000) + +/* + * This is to convert the size of the inbound "BAR" region to the + * non-linear values of PCIE_X_MISC_RC_BAR[123]_CONFIG_LO.SIZE + */ +static int brcm_pcie_encode_ibar_size(u64 size) +{ + int log2_in = ilog2(size); + + if (log2_in >= 12 && log2_in <= 15) + /* Covers 4KB to 32KB (inclusive) */ + return (log2_in - 12) + 0x1c; + else if (log2_in >= 16 && log2_in <= 37) + /* Covers 64KB to 32GB, (inclusive) */ + return log2_in - 15; + /* Something is awry so disable */ + return 0; +} + +/* Configuration space read/write support */ +static inline int brcm_pcie_cfg_index(pci_dev_t bdf, int reg) +{ + return (PCI_DEV(bdf) << PCIE_EXT_SLOT_SHIFT) + | (PCI_FUNC(bdf) << PCIE_EXT_FUNC_SHIFT) + | (PCI_BUS(bdf) << PCIE_EXT_BUSNUM_SHIFT) + | (reg & ~3); +} + +/* The controller is capable of serving in both RC and EP roles */ +static bool brcm_pcie_rc_mode(struct brcm_pcie *pcie) +{ + u32 val = readl(pcie->base + PCIE_MISC_PCIE_STATUS); + + return !!FIELD_GET(PCIE_MISC_PCIE_STATUS_PCIE_PORT_MASK, val); +} + +static bool brcm_pcie_link_up(struct brcm_pcie *pcie) +{ + u32 val = readl(pcie->base + PCIE_MISC_PCIE_STATUS); + u32 dla = FIELD_GET(PCIE_MISC_PCIE_STATUS_PCIE_DL_ACTIVE_MASK, val); + u32 plu = FIELD_GET(PCIE_MISC_PCIE_STATUS_PCIE_PHYLINKUP_MASK, val); + + return dla && plu; +} + +static int brcm_pcie_config_address(const struct udevice *udev, pci_dev_t bdf, + uint offset, void **paddress) +{ + struct brcm_pcie *pcie = dev_get_priv(udev); + unsigned int bus = PCI_BUS(bdf); + unsigned int dev = PCI_DEV(bdf); + int idx; + + /* + * Busses 0 (host PCIe bridge) and 1 (its immediate child) + * are limited to a single device each + */ + if ((bus == (udev->seq + 1)) && dev > 0) + return -ENODEV; + + /* Accesses to the RC go right to the RC registers if PCI device == 0 */ + if (bus == udev->seq) { + if (PCI_DEV(bdf)) + return -ENODEV; + + *paddress = pcie->base + offset; + return 0; + } + + /* For devices, write to the config space index register */ + idx = brcm_pcie_cfg_index(bdf, 0); + + writel(idx, pcie->base + PCIE_EXT_CFG_INDEX); + *paddress = pcie->base + PCIE_EXT_CFG_DATA + offset; + + return 0; +} + +static int brcm_pcie_read_config(const struct udevice *bus, pci_dev_t bdf, + uint offset, ulong *valuep, + enum pci_size_t size) +{ + return pci_generic_mmap_read_config(bus, brcm_pcie_config_address, + bdf, offset, valuep, size); +} + +static int brcm_pcie_write_config(struct udevice *bus, pci_dev_t bdf, + uint offset, ulong value, + enum pci_size_t size) +{ + return pci_generic_mmap_write_config(bus, brcm_pcie_config_address, + bdf, offset, value, size); +} + +static const char *link_speed_to_str(unsigned int s) +{ + static const char * const speed_str[] = { "??", "2.5", "5.0", "8.0" }; + + if (s >= ARRAY_SIZE(speed_str)) + s = 0; + + return speed_str[s]; +} + +static inline void brcm_pcie_bridge_sw_init_set(struct brcm_pcie *pcie, u32 val) +{ + u32 tmp; + + tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1); + u32p_replace_bits(&tmp, val, PCIE_RGR1_SW_INIT_1_INIT_MASK); + writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1); +} + +static inline void brcm_pcie_perst_set(struct brcm_pcie *pcie, u32 val) +{ + u32 tmp; + + tmp = readl(pcie->base + PCIE_RGR1_SW_INIT_1); + u32p_replace_bits(&tmp, val, PCIE_RGR1_SW_INIT_1_PERST_MASK); + writel(tmp, pcie->base + PCIE_RGR1_SW_INIT_1); +} + +static u32 brcm_pcie_mdio_form_pkt(int port, int regad, int cmd) +{ + u32 pkt = 0; + + pkt |= FIELD_PREP(MDIO_PORT_MASK, port); + pkt |= FIELD_PREP(MDIO_REGAD_MASK, regad); + pkt |= FIELD_PREP(MDIO_CMD_MASK, cmd); + + return pkt; +} + +/* Negative return value indicates error */ +static int brcm_pcie_mdio_read(void __iomem *base, u8 port, u8 regad, u32 *val) +{ + int tries; + u32 data; + + writel(brcm_pcie_mdio_form_pkt(port, regad, MDIO_CMD_READ), + base + PCIE_RC_DL_MDIO_ADDR); + readl(base + PCIE_RC_DL_MDIO_ADDR); + + data = readl(base + PCIE_RC_DL_MDIO_RD_DATA); + for (tries = 0; !MDIO_RD_DONE(data) && tries < 10; tries++) { + udelay(10); + data = readl(base + PCIE_RC_DL_MDIO_RD_DATA); + } + + *val = FIELD_GET(MDIO_DATA_MASK, data); + return MDIO_RD_DONE(data) ? 0 : -EIO; +} + +/* Negative return value indicates error */ +static int brcm_pcie_mdio_write(void __iomem *base, u8 port, + u8 regad, u16 wrdata) +{ + int tries; + u32 data; + + writel(brcm_pcie_mdio_form_pkt(port, regad, MDIO_CMD_WRITE), + base + PCIE_RC_DL_MDIO_ADDR); + readl(base + PCIE_RC_DL_MDIO_ADDR); + writel(MDIO_DATA_DONE_MASK | wrdata, base + PCIE_RC_DL_MDIO_WR_DATA); + + data = readl(base + PCIE_RC_DL_MDIO_WR_DATA); + for (tries = 0; !MDIO_WT_DONE(data) && tries < 10; tries++) { + udelay(10); + data = readl(base + PCIE_RC_DL_MDIO_WR_DATA); + } + + return MDIO_WT_DONE(data) ? 0 : -EIO; +} + +/* + * Configures device for Spread Spectrum Clocking (SSC) mode; negative + * return value indicates error. + */ +static int brcm_pcie_set_ssc(struct brcm_pcie *pcie) +{ + void __iomem *base = pcie->base; + int pll, ssc; + int ret; + u32 tmp; + + ret = brcm_pcie_mdio_write(base, MDIO_PORT0, SET_ADDR_OFFSET, + SSC_REGS_ADDR); + if (ret < 0) + return ret; + + ret = brcm_pcie_mdio_read(base, MDIO_PORT0, SSC_CNTL_OFFSET, &tmp); + if (ret < 0) + return ret; + + u32p_replace_bits(&tmp, 1, SSC_CNTL_OVRD_EN_MASK); + u32p_replace_bits(&tmp, 1, SSC_CNTL_OVRD_VAL_MASK); + ret = brcm_pcie_mdio_write(base, MDIO_PORT0, SSC_CNTL_OFFSET, tmp); + if (ret < 0) + return ret; + + udelay(1000); + ret = brcm_pcie_mdio_read(base, MDIO_PORT0, SSC_STATUS_OFFSET, &tmp); + if (ret < 0) + return ret; + + ssc = FIELD_GET(SSC_STATUS_SSC_MASK, tmp); + pll = FIELD_GET(SSC_STATUS_PLL_LOCK_MASK, tmp); + + return ssc && pll ? 0 : -EIO; +} + +/* Limits operation to a specific generation (1, 2, or 3) */ +static void brcm_pcie_set_gen(struct brcm_pcie *pcie, int gen) +{ + void __iomem *base = pcie->base; + + u16 lnkctl2 = readw(base + BRCM_PCIE_CAP_REGS + PCI_EXP_LNKCTL2); + u32 lnkcap = readl(base + BRCM_PCIE_CAP_REGS + PCI_EXP_LNKCAP); + + lnkcap = (lnkcap & ~PCI_EXP_LNKCAP_SLS) | gen; + writel(lnkcap, base + BRCM_PCIE_CAP_REGS + PCI_EXP_LNKCAP); + + lnkctl2 = (lnkctl2 & ~0xf) | gen; + writew(lnkctl2, base + BRCM_PCIE_CAP_REGS + PCI_EXP_LNKCTL2); +} + +static void brcm_pcie_set_outbound_win(struct brcm_pcie *pcie, + unsigned int win, u64 phys_addr, + u64 pcie_addr, u64 size) +{ + void __iomem *base = pcie->base; + u32 phys_addr_mb_high, limit_addr_mb_high; + phys_addr_t phys_addr_mb, limit_addr_mb; + int high_addr_shift; + u32 tmp; + + /* Set the base of the pcie_addr window */ + writel(lower_32_bits(pcie_addr), base + PCIE_MEM_WIN0_LO(win)); + writel(upper_32_bits(pcie_addr), base + PCIE_MEM_WIN0_HI(win)); + + /* Write the addr base & limit lower bits (in MBs) */ + phys_addr_mb = phys_addr / SZ_1M; + limit_addr_mb = (phys_addr + size - 1) / SZ_1M; + + tmp = readl(base + PCIE_MEM_WIN0_BASE_LIMIT(win)); + u32p_replace_bits(&tmp, phys_addr_mb, + PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_BASE_MASK); + u32p_replace_bits(&tmp, limit_addr_mb, + PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_LIMIT_MASK); + writel(tmp, base + PCIE_MEM_WIN0_BASE_LIMIT(win)); + + /* Write the cpu & limit addr upper bits */ + high_addr_shift = PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_LIMIT_BASE_HI_SHIFT; + phys_addr_mb_high = phys_addr_mb >> high_addr_shift; + tmp = readl(base + PCIE_MEM_WIN0_BASE_HI(win)); + u32p_replace_bits(&tmp, phys_addr_mb_high, + PCIE_MISC_CPU_2_PCIE_MEM_WIN0_BASE_HI_BASE_MASK); + writel(tmp, base + PCIE_MEM_WIN0_BASE_HI(win)); + + limit_addr_mb_high = limit_addr_mb >> high_addr_shift; + tmp = readl(base + PCIE_MEM_WIN0_LIMIT_HI(win)); + u32p_replace_bits(&tmp, limit_addr_mb_high, + PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LIMIT_HI_LIMIT_MASK); + writel(tmp, base + PCIE_MEM_WIN0_LIMIT_HI(win)); +} + +static int brcm_pcie_probe(struct udevice *dev) +{ + struct udevice *ctlr = pci_get_controller(dev); + struct pci_controller *hose = dev_get_uclass_priv(ctlr); + struct brcm_pcie *pcie = dev_get_priv(dev); + void __iomem *base = pcie->base; + bool ssc_good = false; + int num_out_wins = 0; + u64 rc_bar2_offset, rc_bar2_size; + unsigned int scb_size_val; + int i, ret; + u16 nlw, cls, lnksta; + u32 tmp; + + /* Reset the bridge */ + brcm_pcie_bridge_sw_init_set(pcie, 1); + + udelay(150); + + /* Take the bridge out of reset */ + brcm_pcie_bridge_sw_init_set(pcie, 0); + + tmp = readl(base + PCIE_MISC_HARD_PCIE_HARD_DEBUG); + tmp &= ~PCIE_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK; + writel(tmp, base + PCIE_MISC_HARD_PCIE_HARD_DEBUG); + /* Wait for SerDes to be stable */ + udelay(150); + + /* Set SCB_MAX_BURST_SIZE, CFG_READ_UR_MODE, SCB_ACCESS_EN */ + u32p_replace_bits(&tmp, 1, PCIE_MISC_MISC_CTRL_SCB_ACCESS_EN_MASK); + u32p_replace_bits(&tmp, 1, PCIE_MISC_MISC_CTRL_CFG_READ_UR_MODE_MASK); + u32p_replace_bits(&tmp, PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_128, + PCIE_MISC_MISC_CTRL_MAX_BURST_SIZE_MASK); + writel(tmp, base + PCIE_MISC_MISC_CTRL); + + /* + * TODO: Use the base address and size(s) provided in the dma-ranges + * property. + */ + rc_bar2_offset = 0; + rc_bar2_size = 1ULL << 32; + + tmp = lower_32_bits(rc_bar2_offset); + u32p_replace_bits(&tmp, brcm_pcie_encode_ibar_size(rc_bar2_size), + PCIE_MISC_RC_BAR2_CONFIG_LO_SIZE_MASK); + writel(tmp, base + PCIE_MISC_RC_BAR2_CONFIG_LO); + writel(upper_32_bits(rc_bar2_offset), + base + PCIE_MISC_RC_BAR2_CONFIG_HI); + + scb_size_val = rc_bar2_size ? + ilog2(rc_bar2_size) - 15 : 0xf; /* 0xf is 1GB */ + tmp = readl(base + PCIE_MISC_MISC_CTRL); + u32p_replace_bits(&tmp, scb_size_val, + PCIE_MISC_MISC_CTRL_SCB0_SIZE_MASK); + writel(tmp, base + PCIE_MISC_MISC_CTRL); + + /* Disable the PCIe->GISB memory window (RC_BAR1) */ + tmp = readl(base + PCIE_MISC_RC_BAR1_CONFIG_LO); + tmp &= ~PCIE_MISC_RC_BAR1_CONFIG_LO_SIZE_MASK; + writel(tmp, base + PCIE_MISC_RC_BAR1_CONFIG_LO); + + /* Disable the PCIe->SCB memory window (RC_BAR3) */ + tmp = readl(base + PCIE_MISC_RC_BAR3_CONFIG_LO); + tmp &= ~PCIE_MISC_RC_BAR3_CONFIG_LO_SIZE_MASK; + writel(tmp, base + PCIE_MISC_RC_BAR3_CONFIG_LO); + + /* Mask all interrupts since we are not handling any yet */ + writel(0xffffffff, base + PCIE_MSI_INTR2_MASK_SET); + + /* Clear any interrupts we find on boot */ + writel(0xffffffff, base + PCIE_MSI_INTR2_CLR); + + if (pcie->gen) + brcm_pcie_set_gen(pcie, pcie->gen); + + /* Unassert the fundamental reset */ + brcm_pcie_perst_set(pcie, 0); + + /* Give the RC/EP time to wake up, before trying to configure RC. + * Intermittently check status for link-up, up to a total of 100ms. + */ + for (i = 0; i < 100 && !brcm_pcie_link_up(pcie); i += 5) + msleep(5); + + if (!brcm_pcie_link_up(pcie)) { + printf("PCIe BRCM: link down\n"); + return -ENODEV; + } + + if (!brcm_pcie_rc_mode(pcie)) { + printf("PCIe misconfigured; is in EP mode\n"); + return -EINVAL; + } + + for (i = 0; i < hose->region_count; i++) { + struct pci_region *reg = &hose->regions[i]; + + if (reg->flags != PCI_REGION_MEM) + continue; + + if (num_out_wins >= BRCM_NUM_PCIE_OUT_WINS) + return -EINVAL; + + brcm_pcie_set_outbound_win(pcie, num_out_wins, reg->phys_start, + reg->bus_start, reg->size); + + num_out_wins++; + } + + /* + * For config space accesses on the RC, show the right class for + * a PCIe-PCIe bridge (the default setting is to be EP mode). + */ + tmp = readl(base + PCIE_RC_CFG_PRIV1_ID_VAL3); + u32p_replace_bits(&tmp, 0x060400, + PCIE_RC_CFG_PRIV1_ID_VAL3_CLASS_CODE_MASK); + writel(tmp, base + PCIE_RC_CFG_PRIV1_ID_VAL3); + + if (pcie->ssc) { + ret = brcm_pcie_set_ssc(base); + if (ret == 0) + ssc_good = true; + else + printf("PCIe BRCM: failed attempt to enter SSC mode\n"); + } + + lnksta = readw(base + BRCM_PCIE_CAP_REGS + PCI_EXP_LNKSTA); + cls = FIELD_GET(PCI_EXP_LNKSTA_CLS, lnksta); + nlw = FIELD_GET(PCI_EXP_LNKSTA_NLW, lnksta); + + printf("PCIe BRCM: link up, %s Gbps x%u %s\n", link_speed_to_str(cls), + nlw, ssc_good ? "(SSC)" : "(!SSC)"); + + /* PCIe->SCB endian mode for BAR */ + tmp = readl(base + PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1); + u32p_replace_bits(&tmp, PCIE_RC_CFG_VENDOR_SPCIFIC_REG1_LITTLE_ENDIAN, + PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1_ENDIAN_MODE_BAR2_MASK); + writel(tmp, base + PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1); + + /* + * Refclk from RC should be gated with CLKREQ# input when ASPM L0s,L1 + * is enabled => setting the CLKREQ_DEBUG_ENABLE field to 1. + */ + tmp = readl(base + PCIE_MISC_HARD_PCIE_HARD_DEBUG); + tmp |= PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK; + writel(tmp, base + PCIE_MISC_HARD_PCIE_HARD_DEBUG); + + return 0; +} + +static int brcm_pcie_ofdata_to_platdata(struct udevice *dev) +{ + struct brcm_pcie *pcie = dev_get_priv(dev); + ofnode dn = dev_ofnode(dev); + u32 max_link_speed; + int ret; + + /* Get the controller base address */ + pcie->base = dev_read_addr_ptr(dev); + if (!pcie->base) + return -EINVAL; + + pcie->ssc = ofnode_read_bool(dn, "brcm,enable-ssc"); + + ret = ofnode_read_u32(dn, "max-link-speed", &max_link_speed); + if (ret < 0 || max_link_speed > 4) + pcie->gen = 0; + else + pcie->gen = max_link_speed; + + return 0; +} + +static const struct dm_pci_ops brcm_pcie_ops = { + .read_config = brcm_pcie_read_config, + .write_config = brcm_pcie_write_config, +}; + +static const struct udevice_id brcm_pcie_ids[] = { + { .compatible = "brcm,bcm2711-pcie" }, + { } +}; + +U_BOOT_DRIVER(pcie_brcm_base) = { + .name = "pcie_brcm", + .id = UCLASS_PCI, + .ops = &brcm_pcie_ops, + .of_match = brcm_pcie_ids, + .probe = brcm_pcie_probe, + .ofdata_to_platdata = brcm_pcie_ofdata_to_platdata, + .priv_auto_alloc_size = sizeof(struct brcm_pcie), +}; From patchwork Fri Apr 24 16:50:12 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: "Sylwester Nawrocki/Kernel \\\(PLT\\\) /SRPOL/Staff Engineer/Samsung Electronics" X-Patchwork-Id: 238423 List-Id: U-Boot discussion From: s.nawrocki at samsung.com (Sylwester Nawrocki) Date: Fri, 24 Apr 2020 18:50:12 +0200 Subject: [PATCH v1 10/10] config: Enable support for the XHCI controller on RPI4 board In-Reply-To: <20200424165012.31915-1-s.nawrocki@samsung.com> References: <20200424165012.31915-1-s.nawrocki@samsung.com> Message-ID: <20200424165012.31915-11-s.nawrocki@samsung.com> From: Marek Szyprowski This requires enabling BRCMSTB PCIe and XHCI_PCI drivers as well as PCI and USB commands. To get it working one has to call the following commands: "pci enum; usb start;", thus such commands have been added to the default "preboot" environment variable. One has to update their environment if it is already configured to get this feature working out of the box. Signed-off-by: Marek Szyprowski --- Changes since RFC: - none. --- configs/rpi_4_32b_defconfig | 9 +++++++++ configs/rpi_4_defconfig | 10 ++++++++++ configs/rpi_arm64_defconfig | 9 ++++++++- 3 files changed, 27 insertions(+), 1 deletion(-) diff --git a/configs/rpi_4_32b_defconfig b/configs/rpi_4_32b_defconfig index 72cda5d..0dd763f 100644 --- a/configs/rpi_4_32b_defconfig +++ b/configs/rpi_4_32b_defconfig @@ -8,6 +8,8 @@ CONFIG_NR_DRAM_BANKS=2 CONFIG_DISTRO_DEFAULTS=y CONFIG_OF_BOARD_SETUP=y # CONFIG_ARCH_FIXUP_FDT_MEMORY is not set +CONFIG_USE_PREBOOT=y +CONFIG_PREBOOT="pci enum; usb start;" CONFIG_MISC_INIT_R=y # CONFIG_DISPLAY_CPUINFO is not set # CONFIG_DISPLAY_BOARDINFO is not set @@ -15,6 +17,8 @@ CONFIG_SYS_PROMPT="U-Boot> " CONFIG_CMD_DFU=y CONFIG_CMD_GPIO=y CONFIG_CMD_MMC=y +CONFIG_CMD_PCI=y +CONFIG_CMD_USB=y CONFIG_CMD_FS_UUID=y CONFIG_OF_BOARD=y CONFIG_ENV_FAT_INTERFACE="mmc" @@ -28,12 +32,17 @@ CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_BCM2835=y CONFIG_DM_ETH=y CONFIG_BCMGENET=y +CONFIG_PCI=y +CONFIG_DM_PCI=y +CONFIG_PCI_BRCMSTB=y CONFIG_PINCTRL=y # CONFIG_PINCTRL_GENERIC is not set # CONFIG_REQUIRE_SERIAL_CONSOLE is not set CONFIG_USB=y CONFIG_DM_USB=y CONFIG_DM_USB_GADGET=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_PCI=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="FSL" CONFIG_USB_GADGET_VENDOR_NUM=0x0525 diff --git a/configs/rpi_4_defconfig b/configs/rpi_4_defconfig index 6d148da..f80e5da 100644 --- a/configs/rpi_4_defconfig +++ b/configs/rpi_4_defconfig @@ -8,6 +8,8 @@ CONFIG_NR_DRAM_BANKS=2 CONFIG_DISTRO_DEFAULTS=y CONFIG_OF_BOARD_SETUP=y # CONFIG_ARCH_FIXUP_FDT_MEMORY is not set +CONFIG_USE_PREBOOT=y +CONFIG_PREBOOT="pci enum; usb start;" CONFIG_MISC_INIT_R=y # CONFIG_DISPLAY_CPUINFO is not set # CONFIG_DISPLAY_BOARDINFO is not set @@ -15,6 +17,8 @@ CONFIG_SYS_PROMPT="U-Boot> " CONFIG_CMD_DFU=y CONFIG_CMD_GPIO=y CONFIG_CMD_MMC=y +CONFIG_CMD_PCI=y +CONFIG_CMD_USB=y CONFIG_CMD_FS_UUID=y CONFIG_OF_BOARD=y CONFIG_ENV_FAT_INTERFACE="mmc" @@ -28,12 +32,18 @@ CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_BCM2835=y CONFIG_DM_ETH=y CONFIG_BCMGENET=y +CONFIG_PCI=y +CONFIG_DM_PCI=y +CONFIG_PCI_BRCMSTB=y CONFIG_PINCTRL=y # CONFIG_PINCTRL_GENERIC is not set # CONFIG_REQUIRE_SERIAL_CONSOLE is not set CONFIG_USB=y CONFIG_DM_USB=y CONFIG_DM_USB_GADGET=y +CONFIG_USB_XHCI_HCD=y +CONFIG_XHCI_64BIT_DWORD_ACCESS_ONLY=y +CONFIG_USB_XHCI_PCI=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_MANUFACTURER="FSL" CONFIG_USB_GADGET_VENDOR_NUM=0x0525 diff --git a/configs/rpi_arm64_defconfig b/configs/rpi_arm64_defconfig index fea86be..926dfc3 100644 --- a/configs/rpi_arm64_defconfig +++ b/configs/rpi_arm64_defconfig @@ -7,13 +7,14 @@ CONFIG_NR_DRAM_BANKS=2 CONFIG_DISTRO_DEFAULTS=y CONFIG_OF_BOARD_SETUP=y CONFIG_USE_PREBOOT=y -CONFIG_PREBOOT="usb start" +CONFIG_PREBOOT="pci enum; usb start;" CONFIG_MISC_INIT_R=y # CONFIG_DISPLAY_CPUINFO is not set # CONFIG_DISPLAY_BOARDINFO is not set CONFIG_SYS_PROMPT="U-Boot> " CONFIG_CMD_GPIO=y CONFIG_CMD_MMC=y +CONFIG_CMD_PCI=y CONFIG_CMD_USB=y CONFIG_CMD_FS_UUID=y CONFIG_OF_BOARD=y @@ -26,11 +27,17 @@ CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_BCM2835=y CONFIG_DM_ETH=y CONFIG_BCMGENET=y +CONFIG_PCI=y +CONFIG_DM_PCI=y +CONFIG_PCI_BRCMSTB=y CONFIG_PINCTRL=y # CONFIG_PINCTRL_GENERIC is not set # CONFIG_REQUIRE_SERIAL_CONSOLE is not set CONFIG_USB=y CONFIG_DM_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_XHCI_64BIT_DWORD_ACCESS_ONLY=y +CONFIG_USB_XHCI_PCI=y CONFIG_USB_DWC2=y CONFIG_USB_KEYBOARD=y CONFIG_USB_HOST_ETHER=y