From patchwork Fri Apr 17 07:19:05 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Joel Johnson X-Patchwork-Id: 237876 List-Id: U-Boot discussion From: mrjoel at lixil.net (Joel Johnson) Date: Fri, 17 Apr 2020 01:19:05 -0600 Subject: [PATCH v1 1/2] arm: mvebu: correct SPL boot configs for SPI/MMC Message-ID: <20200417071906.1098043-1-mrjoel@lixil.net> Update mvebu SPL boot selection mechanism for the move to driver model usage by ensuring that the required driver support for SPI and MMC booting is available in SPL when the respective boot method is selected. Previously, all mvebu boards selected a boot method (implicitly MVEBU_SPL_BOOT_DEVICE_SPI for many) even if SPL booting wasn't used. This changes mvebu boot method selection to depend on SPL usage which resolves the issue with aarch64 boards which don't use SPL getting an implicit boot device selection resulting in unmet dependencies. The 32-bit arm boards do use SPL, but I'm led to conclude that most aren't intentionally using the MVEBU_SPL_BOOT_DEVICE selection since none have SPL_DM_SPI enabled in their defconfig even though they still implicitly select the SPI boot method. This also results in the new addition of SPL_GPIO_SUPPORT to helios4. The mainline dts for helios4 includes the cd-gpios entry for sdhci with identical addresses as the clearfog dts. I don't have a helios4 board to confirm, but based on the current source conclude that the board itself is either wired to pull the signal low for eMMC, or the default MMC boot isn't fully functional in mainline. In either case, as far as I can tell, including the GPIO support will at least cause no regression. Tested on SolidRun ClearFog devices. Signed-off-by: Joel Johnson Reviewed-by: Stefan Roese --- This patch unifies two patches from a prior ClearFog specific series which caused issues when building for most other mvebu boards. Now build and config diff tested for all arm and aarch64 mvebu boards! The only substantive changes end up being the SPL dependency for boot selection, along with defconfig cleanups with Kconfig consolidated boot dependent values. The superfluous addition of SPL_MTD_SUPPORT present in the prior patch for SPI booting was also removed. --- arch/arm/mach-mvebu/Kconfig | 12 ++++++++++++ configs/clearfog_defconfig | 3 --- configs/controlcenterdc_defconfig | 4 ---- configs/db-88f6720_defconfig | 4 ---- configs/db-88f6820-amc_defconfig | 4 ---- configs/db-88f6820-gp_defconfig | 4 ---- configs/db-mv784mp-gp_defconfig | 3 --- configs/ds414_defconfig | 3 --- configs/helios4_defconfig | 1 - configs/maxbcm_defconfig | 3 --- configs/theadorable_debug_defconfig | 3 --- configs/turris_omnia_defconfig | 4 ---- configs/x530_defconfig | 4 ---- include/configs/helios4.h | 5 ----- 14 files changed, 12 insertions(+), 45 deletions(-) diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig index 161dee937f..645990b3ef 100644 --- a/arch/arm/mach-mvebu/Kconfig +++ b/arch/arm/mach-mvebu/Kconfig @@ -232,13 +232,25 @@ config SYS_SOC choice prompt "Boot method" + depends on SPL config MVEBU_SPL_BOOT_DEVICE_SPI bool "SPI NOR flash" + imply ENV_IS_IN_SPI_FLASH + select SPL_DM_SPI + select SPL_SPI_FLASH_SUPPORT + select SPL_SPI_LOAD + select SPL_SPI_SUPPORT config MVEBU_SPL_BOOT_DEVICE_MMC bool "SDIO/MMC card" + imply ENV_IS_IN_MMC + # GPIO needed for eMMC/SD card presence detection + select SPL_DM_GPIO + select SPL_DM_MMC + select SPL_GPIO_SUPPORT select SPL_LIBDISK_SUPPORT + select SPL_MMC_SUPPORT config MVEBU_SPL_BOOT_DEVICE_SATA bool "SATA" diff --git a/configs/clearfog_defconfig b/configs/clearfog_defconfig index 6db8b8acf6..ada35cb53b 100644 --- a/configs/clearfog_defconfig +++ b/configs/clearfog_defconfig @@ -3,14 +3,12 @@ CONFIG_ARCH_CPU_INIT=y CONFIG_SYS_THUMB_BUILD=y CONFIG_ARCH_MVEBU=y CONFIG_SYS_TEXT_BASE=0x00800000 -CONFIG_SPL_GPIO_SUPPORT=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_SYS_MALLOC_F_LEN=0x2000 CONFIG_TARGET_CLEARFOG=y CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC=y CONFIG_DM_GPIO=y -CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_NR_DRAM_BANKS=2 CONFIG_SPL=y @@ -42,7 +40,6 @@ CONFIG_CMD_CACHE=y CONFIG_CMD_TIME=y # CONFIG_SPL_PARTITION_UUIDS is not set CONFIG_DEFAULT_DEVICE_TREE="armada-388-clearfog" -CONFIG_ENV_IS_IN_MMC=y CONFIG_NET_RANDOM_ETHADDR=y CONFIG_SPL_OF_TRANSLATE=y CONFIG_AHCI_MVEBU=y diff --git a/configs/controlcenterdc_defconfig b/configs/controlcenterdc_defconfig index 51126cbdc3..524dbc2b39 100644 --- a/configs/controlcenterdc_defconfig +++ b/configs/controlcenterdc_defconfig @@ -14,8 +14,6 @@ CONFIG_NR_DRAM_BANKS=2 CONFIG_SPL=y CONFIG_DEBUG_UART_BASE=0xd0012000 CONFIG_DEBUG_UART_CLOCK=250000000 -CONFIG_SPL_SPI_FLASH_SUPPORT=y -CONFIG_SPL_SPI_SUPPORT=y CONFIG_DEBUG_UART=y CONFIG_AHCI=y CONFIG_SPL_TEXT_BASE=0x40000030 @@ -28,7 +26,6 @@ CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_LAST_STAGE_INIT=y CONFIG_SPL_BOARD_INIT=y CONFIG_SPL_SYS_MALLOC_SIMPLE=y -CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x30000 CONFIG_HUSH_PARSER=y # CONFIG_CMD_ELF is not set @@ -50,7 +47,6 @@ CONFIG_CMD_EXT4=y CONFIG_EFI_PARTITION=y CONFIG_OF_BOARD_FIXUP=y CONFIG_DEFAULT_DEVICE_TREE="armada-38x-controlcenterdc" -CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_USE_ENV_SPI_MAX_HZ=y CONFIG_ENV_SPI_MAX_HZ=50000000 CONFIG_SYS_RELOC_GD_ENV_ADDR=y diff --git a/configs/db-88f6720_defconfig b/configs/db-88f6720_defconfig index 42c427b792..068f76bbe4 100644 --- a/configs/db-88f6720_defconfig +++ b/configs/db-88f6720_defconfig @@ -14,8 +14,6 @@ CONFIG_NR_DRAM_BANKS=2 CONFIG_SPL=y CONFIG_DEBUG_UART_BASE=0xf1012000 CONFIG_DEBUG_UART_CLOCK=250000000 -CONFIG_SPL_SPI_FLASH_SUPPORT=y -CONFIG_SPL_SPI_SUPPORT=y CONFIG_DEBUG_UART=y CONFIG_SPL_TEXT_BASE=0x40004030 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set @@ -25,7 +23,6 @@ CONFIG_SYS_CONSOLE_INFO_QUIET=y # CONFIG_DISPLAY_BOARDINFO is not set CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_I2C_SUPPORT=y -CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x20000 CONFIG_CMD_I2C=y CONFIG_CMD_SPI=y @@ -43,7 +40,6 @@ CONFIG_CMD_FAT=y CONFIG_CMD_FS_GENERIC=y # CONFIG_DOS_PARTITION is not set CONFIG_DEFAULT_DEVICE_TREE="armada-375-db" -CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_USE_ENV_SPI_MAX_HZ=y CONFIG_ENV_SPI_MAX_HZ=50000000 CONFIG_SYS_RELOC_GD_ENV_ADDR=y diff --git a/configs/db-88f6820-amc_defconfig b/configs/db-88f6820-amc_defconfig index 5bf9eb66ad..e231ca4673 100644 --- a/configs/db-88f6820-amc_defconfig +++ b/configs/db-88f6820-amc_defconfig @@ -14,8 +14,6 @@ CONFIG_NR_DRAM_BANKS=2 CONFIG_SPL=y CONFIG_DEBUG_UART_BASE=0xd0012000 CONFIG_DEBUG_UART_CLOCK=200000000 -CONFIG_SPL_SPI_FLASH_SUPPORT=y -CONFIG_SPL_SPI_SUPPORT=y CONFIG_DEBUG_UART=y CONFIG_SPL_TEXT_BASE=0x40000030 CONFIG_FIT=y @@ -26,7 +24,6 @@ CONFIG_SYS_CONSOLE_INFO_QUIET=y # CONFIG_DISPLAY_BOARDINFO is not set CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_I2C_SUPPORT=y -CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x24000 # CONFIG_CMD_FLASH is not set CONFIG_CMD_I2C=y @@ -48,7 +45,6 @@ CONFIG_EFI_PARTITION=y # CONFIG_PARTITION_UUIDS is not set # CONFIG_SPL_PARTITION_UUIDS is not set CONFIG_DEFAULT_DEVICE_TREE="armada-385-db-88f6820-amc" -CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_USE_ENV_SPI_MAX_HZ=y CONFIG_ENV_SPI_MAX_HZ=50000000 CONFIG_SYS_RELOC_GD_ENV_ADDR=y diff --git a/configs/db-88f6820-gp_defconfig b/configs/db-88f6820-gp_defconfig index 7e3ee5ec1c..c866131025 100644 --- a/configs/db-88f6820-gp_defconfig +++ b/configs/db-88f6820-gp_defconfig @@ -14,8 +14,6 @@ CONFIG_NR_DRAM_BANKS=2 CONFIG_SPL=y CONFIG_DEBUG_UART_BASE=0xd0012000 CONFIG_DEBUG_UART_CLOCK=250000000 -CONFIG_SPL_SPI_FLASH_SUPPORT=y -CONFIG_SPL_SPI_SUPPORT=y CONFIG_DEBUG_UART=y CONFIG_AHCI=y CONFIG_SPL_TEXT_BASE=0x40000030 @@ -26,7 +24,6 @@ CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y CONFIG_SPL_I2C_SUPPORT=y -CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x24000 CONFIG_CMD_I2C=y CONFIG_CMD_MMC=y @@ -48,7 +45,6 @@ CONFIG_EFI_PARTITION=y # CONFIG_PARTITION_UUIDS is not set # CONFIG_SPL_PARTITION_UUIDS is not set CONFIG_DEFAULT_DEVICE_TREE="armada-388-gp" -CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_USE_ENV_SPI_MAX_HZ=y CONFIG_ENV_SPI_MAX_HZ=50000000 CONFIG_SYS_RELOC_GD_ENV_ADDR=y diff --git a/configs/db-mv784mp-gp_defconfig b/configs/db-mv784mp-gp_defconfig index d3a0d0020a..012149a860 100644 --- a/configs/db-mv784mp-gp_defconfig +++ b/configs/db-mv784mp-gp_defconfig @@ -14,8 +14,6 @@ CONFIG_NR_DRAM_BANKS=2 CONFIG_SPL=y CONFIG_DEBUG_UART_BASE=0xd0012000 CONFIG_DEBUG_UART_CLOCK=250000000 -CONFIG_SPL_SPI_FLASH_SUPPORT=y -CONFIG_SPL_SPI_SUPPORT=y CONFIG_DEBUG_UART=y CONFIG_SPL_TEXT_BASE=0x40004030 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set @@ -25,7 +23,6 @@ CONFIG_SYS_CONSOLE_INFO_QUIET=y # CONFIG_DISPLAY_BOARDINFO is not set CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_I2C_SUPPORT=y -CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x20000 # CONFIG_CMD_FLASH is not set CONFIG_CMD_I2C=y diff --git a/configs/ds414_defconfig b/configs/ds414_defconfig index 435c896e41..01a3909c8c 100644 --- a/configs/ds414_defconfig +++ b/configs/ds414_defconfig @@ -14,8 +14,6 @@ CONFIG_NR_DRAM_BANKS=2 CONFIG_SPL=y CONFIG_DEBUG_UART_BASE=0xd0012000 CONFIG_DEBUG_UART_CLOCK=250000000 -CONFIG_SPL_SPI_FLASH_SUPPORT=y -CONFIG_SPL_SPI_SUPPORT=y CONFIG_DEBUG_UART=y CONFIG_SPL_TEXT_BASE=0x40004030 CONFIG_BOOTDELAY=3 @@ -26,7 +24,6 @@ CONFIG_PREBOOT="usb start; sf probe" # CONFIG_DISPLAY_BOARDINFO is not set CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_I2C_SUPPORT=y -CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x24000 # CONFIG_CMD_FLASH is not set CONFIG_CMD_I2C=y diff --git a/configs/helios4_defconfig b/configs/helios4_defconfig index 1b8d130ebc..0fe8559507 100644 --- a/configs/helios4_defconfig +++ b/configs/helios4_defconfig @@ -38,7 +38,6 @@ CONFIG_CMD_CACHE=y CONFIG_CMD_TIME=y # CONFIG_SPL_PARTITION_UUIDS is not set CONFIG_DEFAULT_DEVICE_TREE="armada-388-helios4" -CONFIG_ENV_IS_IN_MMC=y CONFIG_NET_RANDOM_ETHADDR=y CONFIG_SPL_OF_TRANSLATE=y CONFIG_SCSI_AHCI=y diff --git a/configs/maxbcm_defconfig b/configs/maxbcm_defconfig index 60a87edac0..9cc9d66393 100644 --- a/configs/maxbcm_defconfig +++ b/configs/maxbcm_defconfig @@ -14,8 +14,6 @@ CONFIG_NR_DRAM_BANKS=2 CONFIG_SPL=y CONFIG_DEBUG_UART_BASE=0xd0012000 CONFIG_DEBUG_UART_CLOCK=250000000 -CONFIG_SPL_SPI_FLASH_SUPPORT=y -CONFIG_SPL_SPI_SUPPORT=y CONFIG_DEBUG_UART=y CONFIG_SPL_TEXT_BASE=0x40004030 CONFIG_BOOTDELAY=3 @@ -24,7 +22,6 @@ CONFIG_SYS_CONSOLE_INFO_QUIET=y # CONFIG_DISPLAY_BOARDINFO is not set CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_I2C_SUPPORT=y -CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x20000 CONFIG_CMD_I2C=y CONFIG_CMD_SPI=y diff --git a/configs/theadorable_debug_defconfig b/configs/theadorable_debug_defconfig index fb12e841cb..616c07ab54 100644 --- a/configs/theadorable_debug_defconfig +++ b/configs/theadorable_debug_defconfig @@ -15,8 +15,6 @@ CONFIG_NR_DRAM_BANKS=2 CONFIG_SPL=y CONFIG_DEBUG_UART_BASE=0xd0012000 CONFIG_DEBUG_UART_CLOCK=250000000 -CONFIG_SPL_SPI_FLASH_SUPPORT=y -CONFIG_SPL_SPI_SUPPORT=y CONFIG_DEBUG_UART=y CONFIG_SPL_TEXT_BASE=0x40004030 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set @@ -28,7 +26,6 @@ CONFIG_SYS_CONSOLE_INFO_QUIET=y # CONFIG_DISPLAY_BOARDINFO is not set CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_I2C_SUPPORT=y -CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x1a000 CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y diff --git a/configs/turris_omnia_defconfig b/configs/turris_omnia_defconfig index f3ed9917d5..29c49686e2 100644 --- a/configs/turris_omnia_defconfig +++ b/configs/turris_omnia_defconfig @@ -17,8 +17,6 @@ CONFIG_NR_DRAM_BANKS=2 CONFIG_SPL=y CONFIG_DEBUG_UART_BASE=0xd0012000 CONFIG_DEBUG_UART_CLOCK=250000000 -CONFIG_SPL_SPI_FLASH_SUPPORT=y -CONFIG_SPL_SPI_SUPPORT=y CONFIG_DEBUG_UART=y CONFIG_AHCI=y CONFIG_SPL_TEXT_BASE=0x40000030 @@ -32,7 +30,6 @@ CONFIG_MISC_INIT_R=y # CONFIG_DISPLAY_BOARDINFO is not set CONFIG_DISPLAY_BOARDINFO_LATE=y CONFIG_SPL_I2C_SUPPORT=y -CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x24000 CONFIG_CMD_MEMTEST=y CONFIG_SYS_ALT_MEMTEST=y @@ -53,7 +50,6 @@ CONFIG_CMD_HASH=y CONFIG_CMD_BTRFS=y # CONFIG_SPL_PARTITION_UUIDS is not set CONFIG_DEFAULT_DEVICE_TREE="armada-385-turris-omnia" -CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_USE_ENV_SPI_MAX_HZ=y CONFIG_ENV_SPI_MAX_HZ=50000000 CONFIG_SYS_RELOC_GD_ENV_ADDR=y diff --git a/configs/x530_defconfig b/configs/x530_defconfig index a15b0b46b4..c49211df95 100644 --- a/configs/x530_defconfig +++ b/configs/x530_defconfig @@ -15,8 +15,6 @@ CONFIG_NR_DRAM_BANKS=2 CONFIG_SPL=y CONFIG_DEBUG_UART_BASE=0xd0012000 CONFIG_DEBUG_UART_CLOCK=250000000 -CONFIG_SPL_SPI_FLASH_SUPPORT=y -CONFIG_SPL_SPI_SUPPORT=y CONFIG_DEBUG_UART=y CONFIG_SPL_TEXT_BASE=0x40000030 CONFIG_FIT=y @@ -26,7 +24,6 @@ CONFIG_SILENT_U_BOOT_ONLY=y CONFIG_SILENT_CONSOLE_UPDATE_ON_RELOC=y CONFIG_MISC_INIT_R=y CONFIG_SPL_BOARD_INIT=y -CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x24000 CONFIG_SPL_WATCHDOG_SUPPORT=y CONFIG_CMD_MEMINFO=y @@ -47,7 +44,6 @@ CONFIG_CMD_EXT4=y CONFIG_CMD_FAT=y CONFIG_CMD_FS_GENERIC=y CONFIG_DEFAULT_DEVICE_TREE="armada-385-atl-x530" -CONFIG_ENV_IS_IN_SPI_FLASH=y CONFIG_ENV_ADDR=0x100000 CONFIG_SPL_OF_TRANSLATE=y CONFIG_BLK=y diff --git a/include/configs/helios4.h b/include/configs/helios4.h index 5a4c9ae066..af595bc7bc 100644 --- a/include/configs/helios4.h +++ b/include/configs/helios4.h @@ -93,16 +93,11 @@ #define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4) #if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SPI_NOR_FLASH -/* SPL related SPI defines */ -#define CONFIG_SPL_SPI_FLASH_SUPPORT -#define CONFIG_SPL_SPI_LOAD -#define CONFIG_SPL_SPI_SUPPORT #define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS #endif #if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SDIO_MMC_CARD /* SPL related MMC defines */ -#define CONFIG_SPL_MMC_SUPPORT #define CONFIG_SYS_MMC_U_BOOT_OFFS (160 << 10) #define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_MMC_U_BOOT_OFFS #ifdef CONFIG_SPL_BUILD From patchwork Fri Apr 17 07:19:06 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Joel Johnson X-Patchwork-Id: 237875 List-Id: U-Boot discussion From: mrjoel at lixil.net (Joel Johnson) Date: Fri, 17 Apr 2020 01:19:06 -0600 Subject: [PATCH v1 2/2] [WIP] arm: mvebu: Enable helios4 opt-out of SPL GPIO In-Reply-To: <20200417071906.1098043-1-mrjoel@lixil.net> References: <20200417071906.1098043-1-mrjoel@lixil.net> Message-ID: <20200417071906.1098043-2-mrjoel@lixil.net> Change the SPL boot selection of MMC from a hard selection of GPIO to a softer imply and opt-out of GPIO support for helios4. This preserves the previous GPIO-less configuration. Signed-off-by: Joel Johnson --- Aditya Prayoga - if you object to the addition of GPIO to the helios4 SPL, I'd be interested in your thoughts on this option This is an exploratory commit of a viable approach to retain the identical current helios4 current configuration. I think it's not worth it and shouldn't be applied since helios4 uses default MMC boot and there is sufficient space for the SPL image, but is a viable option depending on the opinion of helios4 interested maintainers. --- arch/arm/mach-mvebu/Kconfig | 6 +++--- configs/helios4_defconfig | 1 + 2 files changed, 4 insertions(+), 3 deletions(-) diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig index 645990b3ef..af30d71cc6 100644 --- a/arch/arm/mach-mvebu/Kconfig +++ b/arch/arm/mach-mvebu/Kconfig @@ -245,12 +245,12 @@ config MVEBU_SPL_BOOT_DEVICE_SPI config MVEBU_SPL_BOOT_DEVICE_MMC bool "SDIO/MMC card" imply ENV_IS_IN_MMC - # GPIO needed for eMMC/SD card presence detection - select SPL_DM_GPIO select SPL_DM_MMC - select SPL_GPIO_SUPPORT select SPL_LIBDISK_SUPPORT select SPL_MMC_SUPPORT + # GPIO often needed for eMMC/SD card presence detection + imply SPL_DM_GPIO + imply SPL_GPIO_SUPPORT config MVEBU_SPL_BOOT_DEVICE_SATA bool "SATA" diff --git a/configs/helios4_defconfig b/configs/helios4_defconfig index 0fe8559507..3630a004bd 100644 --- a/configs/helios4_defconfig +++ b/configs/helios4_defconfig @@ -2,6 +2,7 @@ CONFIG_ARM=y CONFIG_ARCH_CPU_INIT=y CONFIG_ARCH_MVEBU=y CONFIG_SYS_TEXT_BASE=0x00800000 +# CONFIG_SPL_GPIO_SUPPORT is not set CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_SYS_MALLOC_F_LEN=0x2000