diff mbox series

[04/13] board: ge: bx50v3: add i2c eeprom bootcount storage

Message ID d557f1a30c6eaf65e55de1345c44f192861143c5.1580475104.git.ian.ray@ge.com
State New
Headers show
Series board: ge: complete DM conversion | expand

Commit Message

Ian Ray Jan. 31, 2020, 1:07 p.m. UTC
From: Robert Beckett <bob.beckett at collabora.com>

Add bootcount node, linking to i2c eeprom "bootcount" partitions for
storage.
Enable i2c eeprom bootcount backend storage.
Enable bootcount command and use it for failbootcmd.

Signed-off-by: Robert Beckett <bob.beckett at collabora.com>
---
 arch/arm/dts/imx6q-bx50v3-uboot.dtsi | 7 ++++++-
 configs/ge_bx50v3_defconfig          | 6 +++---
 include/configs/ge_bx50v3.h          | 4 +---
 3 files changed, 10 insertions(+), 7 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm/dts/imx6q-bx50v3-uboot.dtsi b/arch/arm/dts/imx6q-bx50v3-uboot.dtsi
index 99d409d..77115a7 100644
--- a/arch/arm/dts/imx6q-bx50v3-uboot.dtsi
+++ b/arch/arm/dts/imx6q-bx50v3-uboot.dtsi
@@ -5,6 +5,11 @@ 
  */
 
 / {
+	bootcount {
+		compatible = "u-boot,bootcount-i2c-eeprom";
+		i2c-eeprom = <&bootcount>;
+	};
+
 	wdt-reboot {
 		compatible = "wdt-reboot";
 		wdt = <&wdog1>;
@@ -20,7 +25,7 @@ 
 			size = <1022>;
 		};
 
-		bootcount {
+		bootcount: bootcount {
 			offset = <1022>;
 			size = <2>;
 		};
diff --git a/configs/ge_bx50v3_defconfig b/configs/ge_bx50v3_defconfig
index 384327e..f1f7a0d 100644
--- a/configs/ge_bx50v3_defconfig
+++ b/configs/ge_bx50v3_defconfig
@@ -8,7 +8,6 @@  CONFIG_ENV_SECT_SIZE=0x10000
 CONFIG_ENV_OFFSET=0xC0000
 CONFIG_DM_GPIO=y
 CONFIG_NR_DRAM_BANKS=1
-CONFIG_SYS_BOOTCOUNT_ADDR=0x7000A000
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
 CONFIG_FIT=y
 CONFIG_OF_BOARD_SETUP=y
@@ -29,6 +28,7 @@  CONFIG_CMD_I2C=y
 CONFIG_CMD_MMC=y
 CONFIG_CMD_PCI=y
 # CONFIG_CMD_NFS is not set
+CONFIG_CMD_BOOTCOUNT=y
 CONFIG_CMD_CACHE=y
 CONFIG_CMD_EXT2=y
 CONFIG_CMD_EXT4=y
@@ -44,9 +44,9 @@  CONFIG_ENV_IS_IN_SPI_FLASH=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_DM=y
 CONFIG_BOOTCOUNT_LIMIT=y
-CONFIG_BOOTCOUNT_EXT=y
+CONFIG_DM_BOOTCOUNT=y
+CONFIG_DM_BOOTCOUNT_I2C_EEPROM=y
 CONFIG_BOOTCOUNT_BOOTLIMIT=10
-CONFIG_SYS_BOOTCOUNT_EXT_DEVPART="1:5"
 CONFIG_DM_MMC=y
 CONFIG_DM_I2C=y
 CONFIG_SYS_I2C_MXC=y
diff --git a/include/configs/ge_bx50v3.h b/include/configs/ge_bx50v3.h
index b8b1ec7..b9227fc 100644
--- a/include/configs/ge_bx50v3.h
+++ b/include/configs/ge_bx50v3.h
@@ -109,9 +109,7 @@ 
 		"setcurs 5 4; " \
 		"lcdputs \"Monitor failed to start. " \
 		"Try again, or contact GE Service for support.\"; " \
-		"mw.b 0x7000A000 0xbc; " \
-		"mw.b 0x7000A001 0x00; " \
-		"ext4write ${dev} ${devnum}:5 0x7000A000 /boot/failures 2\0" \
+		"bootcount reset; \0" \
 	"altbootcmd=" \
 		"run doquiet; " \
 		"setenv partnum 1; run hasfirstboot || setenv partnum 2; " \