diff mbox series

[32/42] mmc: exynos_dw_mmc: Set requested freq in get_mmc_clk() callback

Message ID 20240522233135.26835-33-semen.protsenko@linaro.org
State Superseded
Headers show
Series mmc: dw_mmc: Enable eMMC on E850-96 board | expand

Commit Message

Sam Protsenko May 22, 2024, 11:31 p.m. UTC 
By now exynos_dw_mmc driver was relying on the correct CIU clock
frequency being set on driver init. But dw_mmc core is actually trying
to change CIU clock rate dynamically, on init and in set_ios() callback,
which it's requesting via host->get_mmc_clk() callback (the name is
misleading: although it's called "get_mmc_clk()", it can actually
request both get and set operations). Implement setting the requested
rate for CIU clock in Exynos driver to achieve the correct dw_mmc core
driver operation at all times. DDR mode requires the clock to be twice
as fast (when 8 bit bus is used), so handle this too, to make DDR
function properly.

This change makes the eMMC throughput on E850-96 board twice as fast.
That's because "clock-frequency" is set to 800 MHz in E850-96 device
tree, but for DDR52 mode it should be 416 MHz (and TRM states it should
be 400 MHz for DDR50/8bit mode). The dw_mmc core is requesting 52 MHz
bus_hz for DDR52 mode, and DDR+8bit mode means it should be x2 fast, so:

    f_ciu = 2 * ciu_div * f_bus = 2 * 4 * 52e6 = 416 MHz,

where f_ciu   - freq of clock fed to DW MMC block from CMU (SDCLKIN), Hz
      f_bus   - freq of clock fed to the card (CCLKIN), Hz
      ciu_div - value of internal divider (in DW MMC block).

Another way to work that around would be overriding the
"clock-frequency" property in corresponding dts. But setting the clock
frequency dynamically as it's done here looks much neater.

This implementation follows what's done in Linux kernel dw_mmc-exynos
driver in .set_ios() callback for MMC_TIMING_MMC_DDR52 case.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
---
 drivers/mmc/exynos_dw_mmc.c | 10 ++++++++++
 1 file changed, 10 insertions(+)
diff mbox series

Patch

diff --git a/drivers/mmc/exynos_dw_mmc.c b/drivers/mmc/exynos_dw_mmc.c
index d3708ecb6407..938fd51a2ac6 100644
--- a/drivers/mmc/exynos_dw_mmc.c
+++ b/drivers/mmc/exynos_dw_mmc.c
@@ -170,7 +170,17 @@  unsigned int exynos_dwmci_get_clk(struct dwmci_host *host, uint freq)
 	u8 clk_div;
 	int err;
 
+	/* Should be double rate for DDR mode */
+	if (host->mmc->selected_mode == MMC_DDR_52 && host->mmc->bus_width == 8)
+		freq *= 2;
+
 	clk_div = exynos_dwmmc_get_ciu_div(host);
+	err = exynos_dwmmc_set_sclk(host, freq * clk_div);
+	if (err) {
+		printf("DWMMC%d: failed to set clock rate (%d); "
+		       "continue anyway\n", host->dev_index, err);
+	}
+
 	err = exynos_dwmmc_get_sclk(host, &sclk);
 	if (err) {
 		printf("DWMMC%d: failed to get clock rate (%d)\n",