@@ -108,6 +108,7 @@ config IMXRT_SDRAM
This driver is for the sdram memory interface with the SEMC.
source "drivers/ram/aspeed/Kconfig"
+source "drivers/ram/cadence/Kconfig"
source "drivers/ram/rockchip/Kconfig"
source "drivers/ram/sifive/Kconfig"
source "drivers/ram/stm32mp1/Kconfig"
@@ -24,3 +24,5 @@ ifdef CONFIG_SPL_BUILD
obj-$(CONFIG_SPL_STARFIVE_DDR) += starfive/
endif
obj-$(CONFIG_ARCH_OCTEON) += octeon/
+
+obj-$(CONFIG_CADENCE_DDR_CTRL) += cadence/
new file mode 100644
@@ -0,0 +1,12 @@
+if RAM || SPL_RAM
+
+config CADENCE_DDR_CTRL
+ bool "Enable Cadence DDR controller"
+ depends on DM
+ help
+ Enable support for Cadence DDR controller, as found on
+ the Renesas RZ/N1 SoC. This controller has a large number
+ of registers which need to be programmed, mostly using values
+ obtained from Denali SOMA files via a TCL script.
+
+endif
new file mode 100644
@@ -0,0 +1 @@
+obj-$(CONFIG_CADENCE_DDR_CTRL) += ddr_ctrl.o
new file mode 100644
@@ -0,0 +1,414 @@
+// SPDX-License-Identifier: BSD-2-Clause
+/*
+ * Cadence DDR Controller
+ *
+ * Copyright (C) 2015 Renesas Electronics Europe Ltd
+ */
+
+/*
+ * The Cadence DDR Controller has a huge number of registers that principally
+ * cover two aspects, DDR specific timing information and AXI bus interfacing.
+ * Cadence's TCL script generates all of the register values for specific
+ * DDR devices operating at a specific frequency. The TCL script uses Denali
+ * SOMA files as inputs. The tool also generates the AXI bus register values as
+ * well, however this driver assumes that users will want to modifiy these to
+ * meet a specific application's needs.
+ * Therefore, this driver is passed two arrays containing register values for
+ * the DDR device specific information, and explicity sets the AXI registers.
+ *
+ * AXI bus interfacing:
+ * The controller has four AXI slaves connections, and each of these can be
+ * programmed to accept requests from specific AXI masters (using their IDs).
+ * The regions of DDR that can be accessed by each AXI slave can be set such
+ * as to isolate DDR used by one AXI master from another. Further, the maximum
+ * bandwidth allocated to each AXI slave can be set.
+ */
+
+#include <common.h>
+#include <linux/delay.h>
+#include <linux/sizes.h>
+#include <asm/io.h>
+#include <wait_bit.h>
+#include <renesas/ddr_ctrl.h>
+
+/* avoid warning for real pr_debug in <linux/printk.h> */
+#ifdef pr_debug
+#undef pr_debug
+#endif
+
+#ifdef DEBUG
+ #define pr_debug(fmt, args...) printf(fmt, ##args)
+ #define pr_debug2(fmt, args...) printf(fmt, ##args)
+#else
+ #define pr_debug(fmt, args...)
+ #define pr_debug2(fmt, args...)
+#endif
+
+#define DDR_NR_AXI_PORTS 4
+#define DDR_NR_ENTRIES 16
+
+#define DDR_START_REG (0) /* DENALI_CTL_00 */
+#define DDR_CS0_MR1_REG (32 * 4) /* DENALI_CTL_32 */
+#define DDR_CS0_MR2_REG (32 * 4 + 2) /* DENALI_CTL_32 */
+#define DDR_CS1_MR1_REG (34 * 4 + 2) /* DENALI_CTL_34 */
+#define DDR_CS1_MR2_REG (35 * 4) /* DENALI_CTL_35 */
+#define DDR_ECC_ENABLE_REG (36 * 4 + 2) /* DENALI_CTL_36 */
+#define DDR_ECC_DISABLE_W_UC_ERR_REG (37 * 4 + 2) /* DENALI_CTL_37 */
+#define DDR_HALF_DATAPATH_REG (54 * 4) /* DENALI_CTL_54 */
+#define DDR_INTERRUPT_STATUS (56 * 4) /* DENALI_CTL_56 */
+#define DDR_INTERRUPT_ACK (57 * 4) /* DENALI_CTL_57 */
+#define DDR_INTERRUPT_MASK (58 * 4) /* DENALI_CTL_58 */
+#define DDR_CS0_ODT_MAP_REG (62 * 4 + 2) /* DENALI_CTL_62 */
+#define DDR_CS1_ODT_MAP_REG (63 * 4) /* DENALI_CTL_63 */
+#define DDR_ODT_TODTL_2CMD (63 * 4 + 2) /* DENALI_CTL_63 */
+#define DDR_ODT_TODTH_WR (63 * 4 + 3) /* DENALI_CTL_63 */
+#define DDR_ODT_TODTH_RD (64 * 4 + 0) /* DENALI_CTL_64 */
+#define DDR_ODT_EN (64 * 4 + 1) /* DENALI_CTL_64 */
+#define DDR_ODT_WR_TO_ODTH (64 * 4 + 2) /* DENALI_CTL_64 */
+#define DDR_ODT_RD_TO_ODTH (64 * 4 + 3) /* DENALI_CTL_64 */
+#define DDR_DIFF_CS_DELAY_REG (66 * 4) /* DENALI_CTL_66 */
+#define DDR_SAME_CS_DELAY_REG (67 * 4) /* DENALI_CTL_67 */
+#define DDR_RW_PRIORITY_REGS (87 * 4 + 2) /* DENALI_CTL_87 */
+#define DDR_RW_FIFO_TYPE_REGS (88 * 4) /* DENALI_CTL_88 */
+#define DDR_AXI_PORT_PROT_ENABLE_REG (90 * 4 + 3) /* DENALI_CTL_90 */
+#define DDR_ADDR_RANGE_REGS (91 * 4) /* DENALI_CTL_91 */
+#define DDR_RANGE_PROT_REGS (218 * 4 + 2) /* DENALI_CTL_218 */
+#define DDR_ARB_CMD_Q_THRESHOLD_REG (346 * 4 + 2) /* DENALI_CTL_346 */
+#define DDR_AXI_PORT_BANDWIDTH_REG (346 * 4 + 3) /* DENALI_CTL_346 */
+#define DDR_OPT_RMODW_REG (372 * 4 + 3) /* DENALI_CTL_372 */
+
+static void ddrc_writeb(u8 val, void *p)
+{
+ pr_debug2("DDR: %p = 0x%02x\n", p, val);
+ writeb(val, p);
+}
+
+static void ddrc_writew(u16 val, void *p)
+{
+ pr_debug2("DDR: %p = 0x%04x\n", p, val);
+ writew(val, p);
+}
+
+static void ddrc_writel(u32 val, void *p)
+{
+ pr_debug2("DDR: %p = 0x%08x\n", p, val);
+ writel(val, p);
+}
+
+void cdns_ddr_set_mr1(void *base, int cs, u16 odt_impedance, u16 drive_strength)
+{
+ void *reg;
+ u16 tmp;
+
+ if (cs == 0)
+ reg = (u8 *)base + DDR_CS0_MR1_REG;
+ else
+ reg = (u8 *)base + DDR_CS1_MR1_REG;
+
+ tmp = readw(reg);
+
+ tmp &= ~MODE_REGISTER_MASK;
+ tmp |= MODE_REGISTER_MR1;
+
+ tmp &= ~MR1_ODT_IMPEDANCE_MASK;
+ tmp |= odt_impedance;
+
+ tmp &= ~MR1_DRIVE_STRENGTH_MASK;
+ tmp |= drive_strength;
+
+ writew(tmp, reg);
+}
+
+void cdns_ddr_set_mr2(void *base, int cs, u16 dynamic_odt, u16 self_refresh_temp)
+{
+ void *reg;
+ u16 tmp;
+
+ if (cs == 0)
+ reg = (u8 *)base + DDR_CS0_MR2_REG;
+ else
+ reg = (u8 *)base + DDR_CS1_MR2_REG;
+
+ tmp = readw(reg);
+
+ tmp &= ~MODE_REGISTER_MASK;
+ tmp |= MODE_REGISTER_MR2;
+
+ tmp &= ~MR2_DYNAMIC_ODT_MASK;
+ tmp |= dynamic_odt;
+
+ tmp &= ~MR2_SELF_REFRESH_TEMP_MASK;
+ tmp |= self_refresh_temp;
+
+ writew(tmp, reg);
+}
+
+void cdns_ddr_set_odt_map(void *base, int cs, u16 odt_map)
+{
+ void *reg;
+
+ if (cs == 0)
+ reg = (u8 *)base + DDR_CS0_ODT_MAP_REG;
+ else
+ reg = (u8 *)base + DDR_CS1_ODT_MAP_REG;
+
+ writew(odt_map, reg);
+}
+
+void cdns_ddr_set_odt_times(void *base, u8 TODTL_2CMD, u8 TODTH_WR, u8 TODTH_RD,
+ u8 WR_TO_ODTH, u8 RD_TO_ODTH)
+{
+ writeb(TODTL_2CMD, (u8 *)base + DDR_ODT_TODTL_2CMD);
+ writeb(TODTH_WR, (u8 *)base + DDR_ODT_TODTH_WR);
+ writeb(TODTH_RD, (u8 *)base + DDR_ODT_TODTH_RD);
+ writeb(1, (u8 *)base + DDR_ODT_EN);
+ writeb(WR_TO_ODTH, (u8 *)base + DDR_ODT_WR_TO_ODTH);
+ writeb(RD_TO_ODTH, (u8 *)base + DDR_ODT_RD_TO_ODTH);
+}
+
+void cdns_ddr_set_same_cs_delays(void *base, u8 r2r, u8 r2w, u8 w2r, u8 w2w)
+{
+ u32 val = (w2w << 24) | (w2r << 16) | (r2w << 8) | r2r;
+
+ writel(val, (u8 *)base + DDR_SAME_CS_DELAY_REG);
+}
+
+void cdns_ddr_set_diff_cs_delays(void *base, u8 r2r, u8 r2w, u8 w2r, u8 w2w)
+{
+ u32 val = (w2w << 24) | (w2r << 16) | (r2w << 8) | r2r;
+
+ writel(val, (u8 *)base + DDR_DIFF_CS_DELAY_REG);
+}
+
+void cdns_ddr_set_port_rw_priority(void *base, int port,
+ u8 read_pri, u8 write_pri)
+{
+ u8 *reg8 = (u8 *)base + DDR_RW_PRIORITY_REGS;
+
+ reg8 += (port * 3);
+ pr_debug("%s port %d (reg8=%p, DENALI_CTL_%d)\n",
+ __func__, port, reg8, (reg8 - (u8 *)base) / 4);
+
+ ddrc_writeb(read_pri, reg8++);
+ ddrc_writeb(write_pri, reg8++);
+}
+
+/* The DDR Controller has 16 entries. Each entry can specify an allowed address
+ * range (with 16KB resolution) for one of the 4 AXI slave ports.
+ */
+void cdns_ddr_enable_port_addr_range(void *base, int port, int entry,
+ u32 addr_start, u32 size)
+{
+ u32 addr_end;
+ u32 *reg32 = (u32 *)((u8 *)base + DDR_ADDR_RANGE_REGS);
+ u32 tmp;
+
+ reg32 += (port * DDR_NR_ENTRIES * 2);
+ reg32 += (entry * 2);
+ pr_debug("%s port %d, entry %d (reg32=%p, DENALI_CTL_%d)\n",
+ __func__, port, entry, reg32, ((u8 *)reg32 - (u8 *)base) / 4);
+
+ /* These registers represent 16KB address blocks */
+ addr_start /= SZ_16K;
+ size /= SZ_16K;
+ if (size)
+ addr_end = addr_start + size - 1;
+ else
+ addr_end = addr_start;
+
+ ddrc_writel(addr_start, reg32++);
+
+ /*
+ * end_addr: Ensure we only set the bottom 18-bits as DENALI_CTL_218
+ * also contains the AXI0 range protection bits.
+ */
+ tmp = readl(reg32);
+ tmp &= ~(BIT(18) - 1);
+ tmp |= addr_end;
+ ddrc_writel(tmp, reg32);
+}
+
+void cdns_ddr_enable_addr_range(void *base, int entry,
+ u32 addr_start, u32 size)
+{
+ int axi;
+
+ for (axi = 0; axi < DDR_NR_AXI_PORTS; axi++)
+ cdns_ddr_enable_port_addr_range(base, axi, entry,
+ addr_start, size);
+}
+
+void cdns_ddr_enable_port_prot(void *base, int port, int entry,
+ enum cdns_ddr_range_prot range_protection_bits,
+ u16 range_RID_check_bits,
+ u16 range_WID_check_bits,
+ u8 range_RID_check_bits_ID_lookup,
+ u8 range_WID_check_bits_ID_lookup)
+{
+ /*
+ * Technically, the offset here points to the byte before the start of
+ * the range protection registers. However, all entries consist of 8
+ * bytes, except the first one (which is missing a padding byte) so we
+ * work around that subtlely.
+ */
+ u8 *reg8 = (u8 *)base + DDR_RANGE_PROT_REGS;
+
+ reg8 += (port * DDR_NR_ENTRIES * 8);
+ reg8 += (entry * 8);
+ pr_debug("%s port %d, entry %d (reg8=%p, DENALI_CTL_%d)\n",
+ __func__, port, entry, reg8, (reg8 - (u8 *)base) / 4);
+
+ if (port == 0 && entry == 0)
+ ddrc_writeb(range_protection_bits, reg8 + 1);
+ else
+ ddrc_writeb(range_protection_bits, reg8);
+
+ ddrc_writew(range_RID_check_bits, reg8 + 2);
+ ddrc_writew(range_WID_check_bits, reg8 + 4);
+ ddrc_writeb(range_RID_check_bits_ID_lookup, reg8 + 6);
+ ddrc_writeb(range_WID_check_bits_ID_lookup, reg8 + 7);
+}
+
+void cdns_ddr_enable_prot(void *base, int entry,
+ enum cdns_ddr_range_prot range_protection_bits,
+ u16 range_RID_check_bits,
+ u16 range_WID_check_bits,
+ u8 range_RID_check_bits_ID_lookup,
+ u8 range_WID_check_bits_ID_lookup)
+{
+ int axi;
+
+ for (axi = 0; axi < DDR_NR_AXI_PORTS; axi++)
+ cdns_ddr_enable_port_prot(base, axi, entry,
+ range_protection_bits,
+ range_RID_check_bits,
+ range_WID_check_bits,
+ range_RID_check_bits_ID_lookup,
+ range_WID_check_bits_ID_lookup);
+}
+
+void cdns_ddr_set_port_bandwidth(void *base, int port,
+ u8 max_percent, u8 overflow_ok)
+{
+ u8 *reg8 = (u8 *)base + DDR_AXI_PORT_BANDWIDTH_REG;
+
+ reg8 += (port * 3);
+ pr_debug("%s port %d, (reg8=%p, DENALI_CTL_%d)\n",
+ __func__, port, reg8, (reg8 - (u8 *)base) / 4);
+
+ ddrc_writeb(max_percent, reg8++); /* Maximum bandwidth percentage */
+ ddrc_writeb(overflow_ok, reg8++); /* Bandwidth overflow allowed */
+}
+
+void cdns_ddr_ctrl_init(void *ddr_ctrl_basex, int async,
+ const u32 *reg0, const u32 *reg350,
+ u32 ddr_start_addr, u32 ddr_size,
+ int enable_ecc, int enable_8bit)
+{
+ int i, axi, entry;
+ u32 *ddr_ctrl_base = (u32 *)ddr_ctrl_basex;
+ u8 *base8 = (u8 *)ddr_ctrl_basex;
+
+ ddrc_writel(*reg0, ddr_ctrl_base + 0);
+ /* 1 to 6 are read only */
+ for (i = 7; i <= 26; i++)
+ ddrc_writel(*(reg0 + i), ddr_ctrl_base + i);
+ /* 27 to 29 are not changed */
+ for (i = 30; i <= 87; i++)
+ ddrc_writel(*(reg0 + i), ddr_ctrl_base + i);
+
+ /* Enable/disable ECC */
+ if (enable_ecc) {
+ pr_debug("%s enabling ECC\n", __func__);
+ ddrc_writeb(1, base8 + DDR_ECC_ENABLE_REG);
+ } else {
+ ddrc_writeb(0, base8 + DDR_ECC_ENABLE_REG);
+ }
+
+ /* ECC: Disable corruption for read/modify/write operations */
+ ddrc_writeb(1, base8 + DDR_ECC_DISABLE_W_UC_ERR_REG);
+
+ /* Set 8/16-bit data width using reduce bit (enable half datapath)*/
+ if (enable_8bit) {
+ pr_debug("%s using 8-bit data\n", __func__);
+ ddrc_writeb(1, base8 + DDR_HALF_DATAPATH_REG);
+ } else {
+ ddrc_writeb(0, base8 + DDR_HALF_DATAPATH_REG);
+ }
+
+ /* Threshold for command queue */
+ ddrc_writeb(4, base8 + DDR_ARB_CMD_Q_THRESHOLD_REG);
+
+ /* AXI port protection => enable */
+ ddrc_writeb(0x01, base8 + DDR_AXI_PORT_PROT_ENABLE_REG);
+
+ /* Set port interface type, default port priority and bandwidths */
+ for (axi = 0; axi < DDR_NR_AXI_PORTS; axi++) {
+ /* port interface type: synchronous or asynchronous AXI clock */
+ u8 *fifo_reg = base8 + DDR_RW_FIFO_TYPE_REGS + (axi * 3);
+
+ if (async)
+ ddrc_writeb(0, fifo_reg);
+ else
+ ddrc_writeb(3, fifo_reg);
+
+ /* R/W priorities */
+ cdns_ddr_set_port_rw_priority(ddr_ctrl_base, axi, 2, 2);
+
+ /* AXI bandwidth */
+ cdns_ddr_set_port_bandwidth(ddr_ctrl_base, axi, 50, 1);
+ }
+
+ /*
+ * The hardware requires that the valid address ranges must not overlap.
+ * So, we initialise all address ranges to be above the DDR, length 0.
+ */
+ for (entry = 0; entry < DDR_NR_ENTRIES; entry++)
+ cdns_ddr_enable_addr_range(ddr_ctrl_base, entry,
+ ddr_start_addr + ddr_size, 0);
+
+ for (i = 350; i <= 374; i++)
+ ddrc_writel(*(reg350 - 350 + i), ddr_ctrl_base + i);
+
+ /* Disable optimised read-modify-write logic */
+ ddrc_writeb(0, base8 + DDR_OPT_RMODW_REG);
+
+ /*
+ * Disable all interrupts, we are not handling them.
+ * For detail of the interrupt mask, ack and status bits, see the
+ * manual's description of the 'int_status' parameter.
+ */
+ ddrc_writel(0, base8 + DDR_INTERRUPT_MASK);
+
+ /*
+ * Default settings to enable full access to the entire DDR.
+ * Users can set different ranges and access rights by calling these
+ * functions before calling cdns_ddr_ctrl_start().
+ */
+ cdns_ddr_enable_addr_range(ddr_ctrl_base, 0,
+ ddr_start_addr, ddr_size);
+ cdns_ddr_enable_prot(ddr_ctrl_base, 0, CDNS_DDR_RANGE_PROT_BITS_FULL,
+ 0xffff, 0xffff, 0x0f, 0x0f);
+}
+
+void cdns_ddr_ctrl_start(void *ddr_ctrl_basex)
+{
+ u32 *ddr_ctrl_base = (u32 *)ddr_ctrl_basex;
+ u8 *base8 = (u8 *)ddr_ctrl_basex;
+
+ /* Start */
+ ddrc_writeb(1, base8 + DDR_START_REG);
+
+ /* Wait for controller to be ready (interrupt status) */
+ wait_for_bit_le32(base8 + DDR_INTERRUPT_STATUS, 0x100, true, 1000, false);
+
+ /* clear all interrupts */
+ ddrc_writel(~0, base8 + DDR_INTERRUPT_ACK);
+
+ /* Step 19 Wait 500us from MRESETB=1 */
+ udelay(500);
+
+ /* Step 20 tCKSRX wait (From supply stable clock for MCK) */
+ /* DENALI_CTL_19 TREF_ENABLE=0x1(=1), AREFRESH=0x1(=1) */
+ ddrc_writel(0x01000100, ddr_ctrl_base + 19);
+}
new file mode 100644
@@ -0,0 +1,175 @@
+/* SPDX-License-Identifier: BSD-2-Clause */
+/*
+ * Cadence DDR Controller
+ *
+ * Copyright (C) 2015 Renesas Electronics Europe Ltd
+ */
+
+#ifndef CADENCE_DDR_CTRL_H
+#define CADENCE_DDR_CTRL_H
+
+enum cdns_ddr_range_prot {
+ CDNS_DDR_RANGE_PROT_BITS_PRIV_SECURE = 0,
+ CDNS_DDR_RANGE_PROT_BITS_SECURE = 1,
+ CDNS_DDR_RANGE_PROT_BITS_PRIV = 2,
+ CDNS_DDR_RANGE_PROT_BITS_FULL = 3,
+};
+
+/**
+ * Initialise the Cadence DDR Controller, but doesn't start it.
+ *
+ * It sets up the controller so that all 4 AXI slave ports allow access to all
+ * of the DDR with the same settings. This means that:
+ * - Full access permisions.
+ * - All read/write priorities are set to 2.
+ * - Bandwidth is set to 50%, overflow is allowed, i.e. it's a soft limit.
+ * If you want different properties for different ports and/or addr ranges, call
+ * the other functions before calling cdns_ddr_ctrl_start().
+ *
+ * @ddr_ctrl_base Physical address of the DDR Controller.
+ * @async 0 if DDR clock is synchronous with the controller clock
+ * otherwise 1.
+ * @reg0 Pointer to array of 32-bit values to be written to registers
+ * 0 to 87. The values are generated by Cadence TCL scripts.
+ * @reg350 Pointer to array of 32-bit values to be written to registers
+ * 350 to 374. The values are generated by Cadence TCL scripts.
+ * @ddr_start_addr Physical address of the start of DDR.
+ * @ddr_size Size of the DDR in bytes. The controller will set the port
+ * protection range to match this size.
+ * @enable_ecc 0 to disable ECC, 1 to enable it.
+ * @enable_8bit 0 to use 16-bit bus width, 1 to use 8-bit bus width.
+ */
+void cdns_ddr_ctrl_init(void *ddr_ctrl_base, int async,
+ const u32 *reg0, const u32 *reg350,
+ u32 ddr_start_addr, u32 ddr_size,
+ int enable_ecc, int enable_8bit);
+
+/**
+ * Start the Cadence DDR Controller.
+ *
+ * @ddr_ctrl_base Physical address of the DDR Controller.
+ */
+void cdns_ddr_ctrl_start(void *ddr_ctrl_base);
+
+/**
+ * Set the priority for read and write operations for a specific AXI slave port.
+ *
+ * @base Physical address of the DDR Controller.
+ * @port Port number. Range is 0 to 3.
+ * @read_pri Priority for reads. Range is 0 to 3, where 0 is highest priority.
+ * @write_pri Priority for writes. Range is 0 to 3, where 0 is highest priority.
+ */
+void cdns_ddr_set_port_rw_priority(void *base, int port,
+ u8 read_pri, u8 write_pri);
+
+/**
+ * Specify address range for a protection entry, for a specific AXI slave port.
+ *
+ * @base Physical address of the DDR Controller.
+ * @port Port number. Range is 0 to 3.
+ * @entry The protection entry. Range is 0 to 15.
+ * @start_addr Physical of the address range, must be aligned to 16KB.
+ * @size Size of the address range, must be multiple of 16KB.
+ */
+void cdns_ddr_enable_port_addr_range(void *base, int port, int entry,
+ u32 addr_start, u32 size);
+
+/**
+ * Specify address range for a protection entry, for all AXI slave ports.
+ *
+ * @base Physical address of the DDR Controller.
+ * @entry The protection entry. Range is 0 to 15.
+ * @start_addr Physical of the address range, must be aligned to 16KB.
+ * @size Size of the address range, must be multiple of 16KB.
+ */
+void cdns_ddr_enable_addr_range(void *base, int entry,
+ u32 addr_start, u32 size);
+
+/**
+ * Specify protection entry details, for a specific AXI slave port.
+ *
+ * See the hardware manual for details of the range check bits.
+ *
+ * @base Physical address of the DDR Controller.
+ * @port Port number. Range is 0 to 3.
+ * @entry The protection entry. Range is 0 to 15.
+ */
+void cdns_ddr_enable_port_prot(void *base, int port, int entry,
+ enum cdns_ddr_range_prot range_protection_bits,
+ u16 range_RID_check_bits,
+ u16 range_WID_check_bits,
+ u8 range_RID_check_bits_ID_lookup,
+ u8 range_WID_check_bits_ID_lookup);
+
+/**
+ * Specify protection entry details, for all AXI slave ports.
+ *
+ * See the hardware manual for details of the range check bits.
+ *
+ * @base Physical address of the DDR Controller.
+ * @entry The protection entry. Range is 0 to 15.
+ */
+void cdns_ddr_enable_prot(void *base, int entry,
+ enum cdns_ddr_range_prot range_protection_bits,
+ u16 range_RID_check_bits,
+ u16 range_WID_check_bits,
+ u8 range_RID_check_bits_ID_lookup,
+ u8 range_WID_check_bits_ID_lookup);
+
+/**
+ * Specify bandwidth for each AXI port.
+ *
+ * See the hardware manual for details of the range check bits.
+ *
+ * @base Physical address of the DDR Controller.
+ * @port Port number. Range is 0 to 3.
+ * @max_percent 0 to 100.
+ */
+void cdns_ddr_set_port_bandwidth(void *base, int port,
+ u8 max_percent, u8 overflow_ok);
+
+/* Standard JEDEC registers */
+#define MODE_REGISTER_MASK (3 << 14)
+#define MODE_REGISTER_MR0 (0 << 14)
+#define MODE_REGISTER_MR1 (1 << 14)
+#define MODE_REGISTER_MR2 (2 << 14)
+#define MODE_REGISTER_MR3 (3 << 14)
+#define MR1_DRIVE_STRENGTH_MASK ((1 << 5) | (1 << 1))
+#define MR1_DRIVE_STRENGTH_34_OHMS ((0 << 5) | (1 << 1))
+#define MR1_DRIVE_STRENGTH_40_OHMS ((0 << 5) | (0 << 1))
+#define MR1_ODT_IMPEDANCE_MASK ((1 << 9) | (1 << 6) | (1 << 2))
+#define MR1_ODT_IMPEDANCE_60_OHMS ((0 << 9) | (0 << 6) | (1 << 2))
+#define MR1_ODT_IMPEDANCE_120_OHMS ((0 << 9) | (1 << 6) | (0 << 2))
+#define MR1_ODT_IMPEDANCE_40_OHMS ((0 << 9) | (1 << 6) | (1 << 2))
+#define MR1_ODT_IMPEDANCE_20_OHMS ((1 << 9) | (0 << 6) | (0 << 2))
+#define MR1_ODT_IMPEDANCE_30_OHMS ((1 << 9) | (0 << 6) | (1 << 2))
+#define MR2_DYNAMIC_ODT_MASK (3 << 9)
+#define MR2_DYNAMIC_ODT_OFF (0 << 9)
+#define MR2_SELF_REFRESH_TEMP_MASK (1 << 7)
+#define MR2_SELF_REFRESH_TEMP_EXT (1 << 7)
+
+/**
+ * Set certain fields of the JEDEC MR1 register.
+ */
+void cdns_ddr_set_mr1(void *base, int cs, u16 odt_impedance, u16 drive_strength);
+
+/**
+ * Set certain fields of the JEDEC MR2 register.
+ */
+void cdns_ddr_set_mr2(void *base, int cs, u16 dynamic_odt, u16 self_refresh_temp);
+
+/**
+ * Set ODT map of the DDR Controller.
+ */
+void cdns_ddr_set_odt_map(void *base, int cs, u16 odt_map);
+
+/**
+ * Set ODT settings in the DDR Controller.
+ */
+void cdns_ddr_set_odt_times(void *base, u8 TODTL_2CMD, u8 TODTH_WR, u8 TODTH_RD,
+ u8 WR_TO_ODTH, u8 RD_TO_ODTH);
+
+void cdns_ddr_set_same_cs_delays(void *base, u8 r2r, u8 r2w, u8 w2r, u8 w2w);
+void cdns_ddr_set_diff_cs_delays(void *base, u8 r2r, u8 r2w, u8 w2r, u8 w2w);
+
+#endif
Driver for Cadence EDAC DDR controller, as found in the Renesas RZ/N1. Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org> --- (no changes since v6) Changes in v6: - use wait_for_bit macros instead of endless while loop Changes in v5: - move board-specific init out of the driver. Changes in v3: - assorted small cleanups - support version 1.0 silicon (previously #if 0...) drivers/ram/Kconfig | 1 + drivers/ram/Makefile | 2 + drivers/ram/cadence/Kconfig | 12 + drivers/ram/cadence/Makefile | 1 + drivers/ram/cadence/ddr_ctrl.c | 414 +++++++++++++++++++++++++++++++++ include/renesas/ddr_ctrl.h | 175 ++++++++++++++ 6 files changed, 605 insertions(+) create mode 100644 drivers/ram/cadence/Kconfig create mode 100644 drivers/ram/cadence/Makefile create mode 100644 drivers/ram/cadence/ddr_ctrl.c create mode 100644 include/renesas/ddr_ctrl.h