deleted file mode 100644
@@ -1,82 +0,0 @@
-How to use and build U-Boot on mx6sabreauto
--------------------------------------------
-
-mx6sabreauto_defconfig target supports mx6q/mx6dl/mx6qp sabreauto variants.
-
-In order to build it:
-
-$ make mx6sabreauto_defconfig
-
-$ make
-
-This will generate the SPL and u-boot-dtb.img binaries.
-
-- Flash the SPL binary into the SD card:
-
-$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 conv=notrunc && sync
-
-- Flash the u-boot-dtb.img binary into the SD card:
-
-$ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 conv=notrunc && sync
-
-Booting via Falcon mode
------------------------
-
-Write in mx6sabreauto_defconfig the following define below:
-
-CONFIG_SPL_OS_BOOT=y
-
-In order to build it:
-
-$ make mx6sabreauto_defconfig
-
-$ make
-
-This will generate the SPL image called SPL and the u-boot-dtb.img.
-
-- Flash the SPL image into the SD card:
-
-$ sudo dd if=SPL of=/dev/sdb bs=1K seek=1 conv=notrunc && sync
-
-- Flash the u-boot-dtb.img image into the SD card:
-
-$ sudo dd if=u-boot-dtb.img of=/dev/sdb bs=1K seek=69 conv=notrunc && sync
-
-Create a FAT16 boot partition to store uImage and the dtb file, then copy the files there:
-
-$ sudo cp uImage /media/boot
-
-$ sudo cp imx6dl-sabreauto.dtb /media/boot
-
-Create a partition for root file system and extract it there:
-
-$ sudo tar xvf rootfs.tar.gz -C /media/root
-
-The SD card must have enough space for raw "args" and "kernel".
-To configure Falcon mode for the first time, on U-Boot do the following commands:
-
-- Load dtb file from boot partition:
-
-# load mmc 0:1 ${fdt_addr} imx6dl-sabreauto.dtb
-
-- Load kernel image from boot partition:
-
-# load mmc 0:1 ${loadaddr} uImage
-
-- Write kernel at 2MB offset:
-
-# mmc write ${loadaddr} 0x1000 0x4000
-
-- Setup kernel bootargs:
-
-# setenv bootargs "console=ttymxc3,115200 root=/dev/mmcblk0p1 rootfstype=ext4 rootwait quiet rw"
-
-- Prepare args:
-
-# spl export fdt ${loadaddr} - ${fdt_addr}
-
-- Write args 1MB data (0x800 sectors) to 1MB offset (0x800 sectors)
-
-# mmc write 18000000 0x800 0x800
-
-- Restart the board and then SPL binary will launch the kernel directly.
@@ -14,3 +14,4 @@ Freescale
imx8qxp_mek
imxrt1020-evk
imxrt1050-evk
+ mx6sabreauto
new file mode 100644
@@ -0,0 +1,100 @@
+.. SPDX-License-Identifier: GPL-2.0+
+
+mx6sabreauto
+============
+
+How to use and build U-Boot on mx6sabreauto
+-------------------------------------------
+
+mx6sabreauto_defconfig target supports mx6q/mx6dl/mx6qp sabreauto variants.
+
+In order to build it:
+
+.. code-block:: bash
+
+ $ make mx6sabreauto_defconfig
+ $ make
+
+This will generate the SPL and u-boot-dtb.img binaries.
+
+- Flash the SPL binary into the SD card:
+
+.. code-block:: bash
+
+ $ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 conv=notrunc && sync
+
+- Flash the u-boot-dtb.img binary into the SD card:
+
+.. code-block:: bash
+
+ $ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 conv=notrunc && sync
+
+Booting via Falcon mode
+-----------------------
+
+Write in mx6sabreauto_defconfig the following define below:
+
+CONFIG_SPL_OS_BOOT=y
+
+In order to build it:
+
+.. code-block:: bash
+
+ $ make mx6sabreauto_defconfig
+ $ make
+
+This will generate the SPL image called SPL and the u-boot-dtb.img.
+
+- Flash the SPL image into the SD card:
+
+.. code-block:: bash
+
+ $ sudo dd if=SPL of=/dev/sdb bs=1K seek=1 conv=notrunc && sync
+
+- Flash the u-boot-dtb.img image into the SD card:
+
+.. code-block:: bash
+
+ $ sudo dd if=u-boot-dtb.img of=/dev/sdb bs=1K seek=69 conv=notrunc && sync
+
+Create a FAT16 boot partition to store uImage and the dtb file, then copy the files there:
+
+.. code-block:: bash
+
+ $ sudo cp uImage /media/boot
+ $ sudo cp imx6dl-sabreauto.dtb /media/boot
+
+Create a partition for root file system and extract it there:
+
+.. code-block:: bash
+
+ $ sudo tar xvf rootfs.tar.gz -C /media/root
+
+The SD card must have enough space for raw "args" and "kernel".
+To configure Falcon mode for the first time, on U-Boot do the following commands:
+
+- Load dtb file from boot partition::
+
+ # load mmc 0:1 ${fdt_addr} imx6dl-sabreauto.dtb
+
+- Load kernel image from boot partition::
+
+ # load mmc 0:1 ${loadaddr} uImage
+
+- Write kernel at 2MB offset::
+
+ # mmc write ${loadaddr} 0x1000 0x4000
+
+- Setup kernel bootargs::
+
+ # setenv bootargs "console=ttymxc3,115200 root=/dev/mmcblk0p1 rootfstype=ext4 rootwait quiet rw"
+
+- Prepare args::
+
+ # spl export fdt ${loadaddr} - ${fdt_addr}
+
+- Write args 1MB data (0x800 sectors) to 1MB offset (0x800 sectors)::
+
+ # mmc write 18000000 0x800 0x800
+
+- Restart the board and then SPL binary will launch the kernel directly.
Convert plain text documentation to reStructuredText format and add it to Sphinx TOC tree. No essential content change. Signed-off-by: Peng Fan <peng.fan@nxp.com> --- board/freescale/mx6sabreauto/README | 82 ---------------------- doc/board/freescale/index.rst | 1 + doc/board/freescale/mx6sabreauto.rst | 100 +++++++++++++++++++++++++++ 3 files changed, 101 insertions(+), 82 deletions(-) delete mode 100644 board/freescale/mx6sabreauto/README create mode 100644 doc/board/freescale/mx6sabreauto.rst -- 2.28.0