diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 9900b4427412..a949a74ba936 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -938,6 +938,7 @@ dtb-$(CONFIG_TARGET_GE_BX50V3) += \
 	imx6q-b650v3.dtb \
 	imx6q-b450v3.dtb
 
+dtb-$(CONFIG_TARGET_GE_B1X5V2) += imx6dl-b1x5v2.dtb
 dtb-$(CONFIG_TARGET_MX53PPD) += imx53-ppd.dtb
 
 dtb-$(CONFIG_TARGET_VEXPRESS_CA5X2) += vexpress-v2p-ca5s.dtb
diff --git a/arch/arm/dts/imx6dl-b1x5v2.dts b/arch/arm/dts/imx6dl-b1x5v2.dts
new file mode 100644
index 000000000000..f3dffe88886d
--- /dev/null
+++ b/arch/arm/dts/imx6dl-b1x5v2.dts
@@ -0,0 +1,624 @@
+/*
+ * GE B1x5v2 Patient Monitor
+ *
+ * Copyright 2018-2020 GE Inc.
+ * Copyright 2018-2020 Collabora Ltd.
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	compatible = "ge,imx6dl-b1x5v2", "congatec,qmx6", "fsl,imx6dl";
+
+	chosen {
+		bootargs = "console=ttymxc2,115200";
+		stdout-path = &uart3;
+	};
+
+	reg_3p3v: 3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	reg_5v0_audio: regulator-5v0-audio {
+		compatible = "regulator-fixed";
+		regulator-name = "5V0_AUDIO";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_5v>;
+
+		gpio = <&tca6424a 16 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		/*
+		 * This must be always-on for da7212, which has some not properly
+		 * documented dependencies for it's speaker supply pin. The issue
+		 * manifests as speaker volume being very low.
+		 */
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	reg_lcd: regulator-lcd {
+		compatible = "regulator-fixed";
+		regulator-name = "LED_VCC";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+
+		pinctrl-0 = <&pinctrl_q7_lcd_power>;
+		pinctrl-names = "default";
+		gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>; // LCDPWR
+		enable-active-high;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_q7_backlight_enable>;
+		power-supply = <&reg_lcd>;
+		pwms = <&pwm4 0 5000000>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <7>;
+		enable-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+	};
+
+	panel {
+		compatible = "simple-panel";
+		backlight = <&backlight>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+
+	bootcount {
+		compatible = "u-boot,bootcount-spi-flash";
+		spi-flash = <&flash>;
+		offset = <0x01003fe>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_q7_gpio1 &pinctrl_q7_gpio3 &pinctrl_q7_gpio5>;
+
+		alarm1 {
+			label = "alarm:red";
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		alarm2 {
+			label = "alarm:yellow";
+			gpios = <&gpio4 27 GPIO_ACTIVE_HIGH>;
+		};
+
+		alarm3 {
+			label = "alarm:blue";
+			gpios = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	poweroff {
+		compatible = "gpio-poweroff";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_q7_spi_cs1>;
+		gpios = <&gpio4 25 GPIO_ACTIVE_LOW>;
+		active-delay-ms = <1000>;
+		inactive-delay-ms = <0>;
+		timeout-ms = <5000>;
+	};
+
+	i2cmux {
+		compatible = "i2c-mux-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_i2cmux>;
+		mux-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>;
+		i2c-parent = <&i2c2>;
+		idle-state = <1>;
+
+		i2c5: i2c at 0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			tmp112: temperature-sensor at 48 {
+				compatible = "ti,tmp112";
+				reg = <0x48>;
+				interrupt-parent = <&tca6424a>;
+				interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+			};
+
+			tca6424a: gpio-controller at 22 {
+				compatible = "ti,tca6424";
+				reg = <0x22>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				interrupt-parent = <&gpio7>;
+				interrupts = <11 IRQ_TYPE_EDGE_RISING>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_q7_gpio6>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+
+				gpio-line-names = "GPIO_ROTOR#", "", "TMP_SENSOR_IRQ", "ACM_GPIO1", "ACM_GPIO2", "BATT_T", "", "",
+						  "ACM_GPIO3", "ACM_GPIO4", "USB1_POWER_EN", "EGPIO_CC_CTL0", "EGPIO_CC_CTL1", "12V_OEMNBP_EN", "CP2105_RST", "",
+						  "SPEAKER_PA_EN", "ARM7_UPI_RESET", "ARM7_PWR_RST", "NURSE_CALL", "MARKER_EN", "EGPIO_TOUCH_RST", "", "";
+			};
+		};
+
+		i2c6: i2c at 1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			pmic: pmic at 08 {
+				compatible = "fsl,pfuze100";
+				reg = <0x08>;
+			};
+		};
+	};
+};
+
+&pmic {
+	regulators {
+		sw1a_reg: sw1ab {
+			regulator-min-microvolt = <300000>;
+			regulator-max-microvolt = <1875000>;
+			regulator-boot-on;
+			regulator-always-on;
+			regulator-ramp-delay = <6250>;
+		};
+
+		sw1c_reg: sw1c {
+			regulator-min-microvolt = <300000>;
+			regulator-max-microvolt = <1875000>;
+			regulator-boot-on;
+			regulator-always-on;
+			regulator-ramp-delay = <6250>;
+		};
+
+		sw2_reg: sw2 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		sw3a_reg: sw3a {
+			regulator-min-microvolt = <400000>;
+			regulator-max-microvolt = <1975000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		sw3b_reg: sw3b {
+			regulator-min-microvolt = <400000>;
+			regulator-max-microvolt = <1975000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		sw4_reg: sw4 {
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		swbst_reg: swbst {
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5150000>;
+		};
+
+		snvs_reg: vsnvs {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vref_reg: vrefddr {
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		/* keep VGEN3, VGEN4 and VGEN5 enabled in order to maintain backward compatibility with hw-rev. A.0 */
+		vgen3_reg: vgen3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		vgen4_reg: vgen4 {
+			regulator-min-microvolt = <2500000>;
+			regulator-max-microvolt = <2500000>;
+			regulator-always-on;
+		};
+
+		vgen5_reg: vgen5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		/* supply voltage for eMMC */
+		vgen6_reg: vgen6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+	};
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&usdhc2 {
+	/* MicroSD card slot */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	wakeup-source;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
+
+&usdhc3 {
+	/* eMMC module */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	non-removable;
+	bus-width = <8>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	wakeup-source;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio3 28 GPIO_ACTIVE_HIGH>;
+
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	status = "okay";
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	scl-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+
+	clock-frequency = <100000>;
+};
+
+&i2c3 {
+	status = "okay";
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_gpio>;
+	scl-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+
+	clock-frequency = <100000>;
+
+	rtc: m41t62 at 68 {
+		compatible = "st,m41t62";
+		reg = <0x68>;
+	};
+};
+
+&ldb {
+	status = "okay";
+
+	lvds0: lvds-channel at 0 {
+		status = "okay";
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <24>;
+
+		port at 4 {
+			reg = <4>;
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet &pinctrl_phy_reset>;
+	phy-mode = "rgmii";
+	status = "okay";
+
+	phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <2>;
+
+	fsl,magic-packet;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy at 6 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <6>;
+		};
+	};
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	num-cs = <1>;
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+
+	flash: m25p80 at 0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "st,sst25vf032b", "jedec,spi-nor";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+
+		partition at 0 {
+			label = "bootloader";
+			reg = <0x0000000 0x100000>;
+		};
+
+		partition at 100000 {
+			label = "user";
+			reg = <0x0100000 0x2fc000>;
+		};
+
+		partition at 3fc000 {
+			label = "reserved";
+			reg = <0x03fc000 0x4000>;
+			read-only;
+		};
+	};
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+};
+
+&iomuxc {
+	imx6qdl-congatec-qmx6 {
+		pinctrl_uart2: uart2grp {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D26__UART2_TX_DATA	0x1b0b1
+				MX6QDL_PAD_EIM_D27__UART2_RX_DATA	0x1b0b1
+			>;
+		};
+
+		pinctrl_uart3: uart3grp {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
+				MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
+			>;
+		};
+
+		pinctrl_wdog: wdoggrp {
+			fsl,pins = <
+				MX6QDL_PAD_DISP0_DAT8__WDOG1_B		0x1b0b0
+			>;
+		};
+
+		pinctrl_usdhc2: usdhc2grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+				MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+				MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+				MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+				MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+				MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+			>;
+		};
+
+		pinctrl_usdhc2_cd: sd2cdgrp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1b0b0
+			>;
+		};
+
+		pinctrl_usdhc3: usdhc4grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+				MX6QDL_PAD_SD3_DAT4__SD3_DATA4		0x17059
+				MX6QDL_PAD_SD3_DAT5__SD3_DATA5		0x17059
+				MX6QDL_PAD_SD3_DAT6__SD3_DATA6		0x17059
+				MX6QDL_PAD_SD3_DAT7__SD3_DATA7		0x17059
+			>;
+		};
+
+		pinctrl_i2c1: i2c1grp {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
+				MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+			>;
+		};
+
+		pinctrl_i2c1_gpio: i2c1gpiogrp {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D21__GPIO3_IO21		0x1b0b0
+				MX6QDL_PAD_EIM_D28__GPIO3_IO28		0x1b0b0
+			>;
+		};
+
+		pinctrl_i2c2: i2c2grp {
+			fsl,pins = <
+				MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
+				MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+			>;
+		};
+
+		pinctrl_i2c2_gpio: i2c2gpiogrp {
+			fsl,pins = <
+				MX6QDL_PAD_KEY_COL3__GPIO4_IO12		0x1b0b0
+				MX6QDL_PAD_KEY_ROW3__GPIO4_IO13		0x1b0b0
+			>;
+		};
+
+		pinctrl_i2c3: i2c3grp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_3__I2C3_SCL		0x4001b8b1
+				MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
+			>;
+		};
+
+		pinctrl_i2c3_gpio: i2c3gpiogrp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_3__GPIO1_IO03		0x1b0b0
+				MX6QDL_PAD_GPIO_6__GPIO1_IO06		0x1b0b0
+			>;
+		};
+
+		pinctrl_ecspi1: ecspi1grp {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
+				MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
+				MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
+				MX6QDL_PAD_EIM_D19__GPIO3_IO19          0x1b0b0
+			>;
+		};
+
+		pinctrl_enet: enetgrp {
+			fsl,pins = <
+				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
+				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
+				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
+				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
+				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
+				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
+				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
+				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
+				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
+				MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x1b0b0
+			>;
+		};
+
+		pinctrl_phy_reset: phyrstgrp {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D23__GPIO3_IO23		0x1b0b0		/* RGMII Phy Reset */
+			>;
+		};
+
+		pinctrl_pwm4: pwm4grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_CMD__PWM4_OUT		0x1b0b1		/* Q7[123] LVDS_BLT_CTRL */
+			>;
+		};
+
+		pinctrl_q7_lcd_power: lcdpwrgrp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_7__GPIO1_IO07		0x1b0b0		/* Q7[111] LVDS_PPEN */
+			>;
+		};
+
+		pinctrl_q7_backlight_enable: blengrp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_9__GPIO1_IO09		0x1b0b0		/* Q7[112] LVDS_BLEN */
+			>;
+		};
+
+		pinctrl_q7_gpio1: q7gpio1grp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_8__GPIO1_IO08		0x1b0b0		/* Q7[186] GPIO1 */
+			>;
+		};
+
+		pinctrl_q7_gpio3: q7gpio3grp {
+			fsl,pins = <
+				MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27	0x1b0b0		/* Q7[188] GPIO3 */
+			>;
+		};
+
+		pinctrl_q7_gpio5: q7gpio5grp {
+			fsl,pins = <
+				MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b0		/* Q7[190] GPIO5 */
+			>;
+		};
+
+		pinctrl_q7_gpio6: q7gpio6grp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_16__GPIO7_IO11		0x1b0b0		/* Q7[191] GPIO6 */
+			>;
+		};
+
+		pinctrl_q7_spi_cs1: spics1grp {
+			fsl,pins = <
+				MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25	0x1b0b0		/* Q7[202] SPI_CS1# */
+			>;
+		};
+
+		pinctrl_i2cmux: i2cmuxgrp {
+			fsl,pins = <
+				MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09	0x1b0b0
+			>;
+		};
+	};
+};
diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig
index fa6e1112e62d..c6fbb356d47d 100644
--- a/arch/arm/mach-imx/mx6/Kconfig
+++ b/arch/arm/mach-imx/mx6/Kconfig
@@ -249,6 +249,15 @@ config TARGET_GE_BX50V3
 	select BOARD_LATE_INIT
 	select MX6Q
 
+config TARGET_GE_B1X5V2
+	bool "General Electric B1x5v2"
+	select CPU_V7
+	select BOARD_LATE_INIT
+	select DM
+	select DM_THERMAL
+	select MX6QDL
+	select SUPPORT_SPL
+
 config TARGET_GW_VENTANA
 	bool "gw_ventana"
 	select MX6QDL
@@ -687,6 +696,7 @@ config SYS_SOC
 	default "mx6"
 
 source "board/ge/bx50v3/Kconfig"
+source "board/ge/b1x5v2/Kconfig"
 source "board/advantech/dms-ba16/Kconfig"
 source "board/aristainetos/Kconfig"
 source "board/armadeus/opos6uldev/Kconfig"
diff --git a/board/ge/b1x5v2/Kconfig b/board/ge/b1x5v2/Kconfig
new file mode 100644
index 000000000000..80a5bcae7dee
--- /dev/null
+++ b/board/ge/b1x5v2/Kconfig
@@ -0,0 +1,14 @@
+if TARGET_GE_B1X5V2
+
+config SYS_BOARD
+	default "b1x5v2"
+
+config SYS_VENDOR
+	default "ge"
+
+config SYS_CONFIG_NAME
+	default "ge_b1x5v2"
+
+source "board/ge/common/Kconfig"
+
+endif
diff --git a/board/ge/b1x5v2/Makefile b/board/ge/b1x5v2/Makefile
new file mode 100644
index 000000000000..8a27af52e1ae
--- /dev/null
+++ b/board/ge/b1x5v2/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Copyright 2018-2020 Collabora
+# Copyright 2018-2020 GE
+
+obj-y :=  b1x5v2.o spl.o
diff --git a/board/ge/b1x5v2/b1x5v2.c b/board/ge/b1x5v2/b1x5v2.c
new file mode 100644
index 000000000000..84189088314d
--- /dev/null
+++ b/board/ge/b1x5v2/b1x5v2.c
@@ -0,0 +1,710 @@
+/*
+ * GE B105v2, B125v2, B155v2
+ *
+ * Copyright 2018-2020 GE Inc.
+ * Copyright 2018-2020 Collabora Ltd.
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <asm/mach-imx/video.h>
+#include <command.h>
+#include <common.h>
+#include <i2c.h>
+#include <input.h>
+#include <ipu_pixfmt.h>
+#include <linux/delay.h>
+#include <linux/fb.h>
+#include <malloc.h>
+#include <miiphy.h>
+#include <micrel.h>
+#include <netdev.h>
+#include <panel.h>
+#include <rtc.h>
+#include <spi_flash.h>
+#include <version.h>
+
+#include "../common/vpd_reader.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifndef CONFIG_SPL_BUILD
+
+#define B1X5V2_GE_VPD_OFFSET	0x0100000
+#define B1X5V2_GE_VPD_SIZE	1022
+
+#define VPD_TYPE_INVALID	0x00
+#define VPD_BLOCK_NETWORK	0x20
+#define VPD_BLOCK_HWID		0x44
+#define VPD_MAC_ADDRESS_LENGTH	6
+
+#define VPD_FLAG_VALID_MAC	BIT(1)
+
+static struct vpd_cache {
+	bool is_read;
+	u8 product_id;
+	unsigned char mac[VPD_MAC_ADDRESS_LENGTH];
+	u32 flags;
+} vpd;
+
+enum product_type {
+	PRODUCT_TYPE_B105V2 = 6,
+	PRODUCT_TYPE_B105PV2 = 7,
+	PRODUCT_TYPE_B125V2 = 8,
+	PRODUCT_TYPE_B125PV2 = 9,
+	PRODUCT_TYPE_B155V2 = 10,
+
+	PRODUCT_TYPE_INVALID = 0,
+};
+
+int dram_init(void) {
+	gd->ram_size = imx_ddr_size();
+	return 0;
+}
+
+int power_init_board(void)
+{
+	/* all required PMIC configuration happens via DT */
+	return 0;
+}
+
+int mx6_rgmii_rework(struct phy_device *phydev)
+{
+	unsigned short id1, id2;
+	unsigned short val;
+
+	id1 = phy_read(phydev, MDIO_DEVAD_NONE, 2);
+	id2 = phy_read(phydev, MDIO_DEVAD_NONE, 3);
+
+	if ((id1 == 0x004d) && (id2 == 0xd072)) { /* AR8035 */
+		/* enable AR8035 ouput a 125MHz clk from CLK_25M */
+		phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, 0x7);
+		phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, MII_KSZ9031_MOD_DATA_POST_INC_RW | 0x16);
+		phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, MII_KSZ9031_MOD_DATA_NO_POST_INC | 0x7);
+		val = phy_read(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA);
+		val &= 0xfe63;
+		val |= 0x18;
+		phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, val);
+
+		/* introduce tx clock delay */
+		phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
+		val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
+		val |= 0x0100;
+		phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
+
+		/* disable hibernation */
+		phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0xb);
+		val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
+		phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x3c40);
+	} else {
+		printf("Unknown PHY ID: %04x %04x\n", id1, id2);
+	}
+
+	return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	mx6_rgmii_rework(phydev);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+
+static int auo_g101evn01_detect(const struct display_info_t *info)
+{
+	char *dev = env_get("devicetype");
+	return !strcmp(dev, "B105v2") || !strcmp(dev, "B105Pv2");
+}
+
+static int auo_g121ean01_detect(const struct display_info_t *info)
+{
+	char *dev = env_get("devicetype");
+	return !strcmp(dev, "B125v2") || !strcmp(dev, "B125Pv2");;
+}
+
+static int auo_g156xtn01_detect(const struct display_info_t *info)
+{
+	char *dev = env_get("devicetype");
+	return !strcmp(dev, "B155v2");
+}
+
+static void b1x5v2_backlight_enable(int percent)
+{
+	struct udevice *panel;
+	int ret;
+
+	ret = uclass_get_device(UCLASS_PANEL, 0, &panel);
+	if (ret) {
+		printf("Could not find panel: %d\n", ret);
+		return;
+	}
+
+	panel_set_backlight(panel, percent);
+	panel_enable_backlight(panel);
+
+}
+
+static void lcd_enable(const struct display_info_t *info)
+{
+	printf("Enable backlight...\n");
+	b1x5v2_backlight_enable(100);
+}
+
+struct display_info_t const displays[] = {
+{
+	.di = 0,
+	.bus = -1,
+	.addr = -1,
+	.pixfmt = IPU_PIX_FMT_RGB24,
+	.detect = auo_g156xtn01_detect,
+	.enable = lcd_enable,
+	.mode = {
+		.name = "AUO G156XTN01",
+		.refresh = 60,
+		.xres = 1368, /* because of i.MX6 limitation, actually 1366 */
+		.yres = 768,
+		.pixclock = 13158, /* 76 MHz in ps */
+		.left_margin = 33,
+		.right_margin = 67,
+		.upper_margin = 4,
+		.lower_margin = 4,
+		.hsync_len = 94,
+		.vsync_len = 30,
+		.sync = FB_SYNC_EXT,
+		.vmode = FB_VMODE_NONINTERLACED
+	}
+},
+{
+	.di = 0,
+	.bus = -1,
+	.addr = -1,
+	.pixfmt = IPU_PIX_FMT_RGB24,
+	.detect = auo_g121ean01_detect,
+	.enable = lcd_enable,
+	.mode = {
+		.name = "AUO G121EAN01.4",
+		.refresh = 60,
+		.xres = 1280,
+		.yres = 800,
+		.pixclock = 14992, /* 66.7 MHz in ps */
+		.left_margin = 8,
+		.right_margin = 58,
+		.upper_margin = 6,
+		.lower_margin = 4,
+		.hsync_len = 70,
+		.vsync_len = 10,
+		.sync = FB_SYNC_EXT,
+		.vmode = FB_VMODE_NONINTERLACED
+	}
+},
+{
+	.di = 0,
+	.bus = -1,
+	.addr = -1,
+	.pixfmt = IPU_PIX_FMT_RGB24,
+	.detect = auo_g101evn01_detect,
+	.enable = lcd_enable,
+	.mode = {
+		.name = "AUO G101EVN01.3",
+		.refresh = 60,
+		.xres = 1280,
+		.yres = 800,
+		.pixclock = 14992, /* 66.7 MHz in ps */
+		.left_margin = 8,
+		.right_margin = 58,
+		.upper_margin = 6,
+		.lower_margin = 4,
+		.hsync_len = 70,
+		.vsync_len = 10,
+		.sync = FB_SYNC_EXT,
+		.vmode = FB_VMODE_NONINTERLACED
+	}
+}
+};
+size_t display_count = ARRAY_SIZE(displays);
+
+static void enable_videopll(void)
+{
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+	s32 timeout = 100000;
+
+	setbits_le32(&ccm->analog_pll_video, BM_ANADIG_PLL_VIDEO_POWERDOWN);
+
+	/* PLL_VIDEO  455MHz (24MHz * (37+11/12) / 2)
+	 *   |
+	 * PLL5
+	 *   |
+	 * CS2CDR[LDB_DI0_CLK_SEL]
+	 *   |
+	 *   +----> LDB_DI0_SERIAL_CLK_ROOT
+	 *   |
+	 *   +--> CSCMR2[LDB_DI0_IPU_DIV] --> LDB_DI0_IPU  455 / 7 = 65 MHz
+	 */
+
+	clrsetbits_le32(&ccm->analog_pll_video,
+			BM_ANADIG_PLL_VIDEO_DIV_SELECT |
+			BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT,
+			BF_ANADIG_PLL_VIDEO_DIV_SELECT(37) |
+			BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(1));
+
+	writel(BF_ANADIG_PLL_VIDEO_NUM_A(11), &ccm->analog_pll_video_num);
+	writel(BF_ANADIG_PLL_VIDEO_DENOM_B(12), &ccm->analog_pll_video_denom);
+
+	clrbits_le32(&ccm->analog_pll_video, BM_ANADIG_PLL_VIDEO_POWERDOWN);
+
+	while (timeout--)
+		if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK)
+			break;
+
+	if (timeout < 0)
+		printf("Warning: video pll lock timeout!\n");
+
+	clrsetbits_le32(&ccm->analog_pll_video,
+			BM_ANADIG_PLL_VIDEO_BYPASS,
+			BM_ANADIG_PLL_VIDEO_ENABLE);
+}
+
+static void setup_display(void)
+{
+	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+	enable_videopll();
+
+	/* When a reset/reboot is performed the display power needs to be turned
+	 * off for atleast 500ms. The boot time is ~300ms, we need to wait for
+	 * an additional 200ms here. Unfortunately we use external PMIC for
+	 * doing the reset, so can not differentiate between POR vs soft reset
+	 */
+	mdelay(200);
+
+	/* CCM_CSCMR2 -> ldb_di0_ipu_div [IMX6SDLRM page 839] */
+	/* divide IPU clock by 7 */
+	setbits_le32(&mxc_ccm->cscmr2, MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV);
+
+	/* CCM_CHSCCDR -> ipu1_di0_clk_sel [IMX6SDLRM page 849] */
+	/* Set LDB_DI0 as clock source for IPU_DI0 */
+	clrsetbits_le32(&mxc_ccm->chsccdr,
+			MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK,
+			(CHSCCDR_CLK_SEL_LDB_DI0 <<
+			MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET));
+
+	/* Turn on IPU LDB DI0 clocks */
+	setbits_le32(&mxc_ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK);
+
+	enable_ipu_clock();
+
+	/* IOMUXC_GPR2 [IMX6SDLRM page 2049] */
+	/* Set LDB Channel 0 in SPWG 24 Bit mode */
+	writel(IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_HIGH |
+	       IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG |
+	       IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT |
+	       IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0,
+	       &iomux->gpr[2]);
+
+	/* IOMUXC_GPR3 [IMX6SDLRM page 2051] */
+	/* LVDS0 is connected to IPU DI0 */
+	clrsetbits_le32(&iomux->gpr[3],
+			IOMUXC_GPR3_LVDS0_MUX_CTL_MASK,
+		       (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 <<
+			IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET));
+}
+
+/*
+ * Do not overwrite the console
+ * Use always serial for U-Boot console
+ */
+int overwrite_console(void)
+{
+	return 1;
+}
+
+int board_early_init_f(void)
+{
+	select_ldb_di_clock_source(MXC_PLL5_CLK);
+
+	return 0;
+}
+
+int eeti_touch_get_model(struct udevice *dev, char *result) {
+	u8 query[68] = {0x67, 0x00, 0x42, 0x00, 0x03, 0x01, 'E', 0x00, 0x00, 0x00};
+	struct i2c_msg qmsg = {
+		.addr = 0x2a,
+		.flags = 0,
+		.len = sizeof(query),
+		.buf = query,
+	};
+	u8 reply[66] = {0};
+	struct i2c_msg rmsg = {
+		.addr = 0x2a,
+		.flags = I2C_M_RD,
+		.len = sizeof(reply),
+		.buf = reply,
+	};
+	int err;
+
+	err = dm_i2c_xfer(dev, &qmsg, 1);
+	if (err)
+		return err;
+
+	/*
+	 * device sends IRQ when its ok to read. To keep the code
+	 * simple we just wait an arbitrary, long enough time period.
+	 */
+	mdelay(10);
+
+	err = dm_i2c_xfer(dev, &rmsg, 1);
+	if (err)
+		return err;
+
+	if (reply[0] != 0x42 || reply[1] != 0x00 ||
+	    reply[2] != 0x03 || reply[4] != 'E')
+		return -EPROTO;
+
+	memcpy(result, reply+5, 10);
+	return 0;
+}
+
+bool b1x5v2_board_is_p_model(void)
+{
+	struct udevice *bus = NULL;
+	struct udevice *dev = NULL;
+	int err;
+
+	err = uclass_get_device_by_name(UCLASS_I2C, "i2c at 21a0000", &bus);
+	if (err || !bus) {
+		printf("Could not get I2C bus: %d\n", err);
+		return true;
+	}
+
+	/* The P models do not have this port expander */
+	err = dm_i2c_probe(bus, 0x21, 0, &dev);
+	if (err || !dev) {
+		return true;
+	}
+
+	return false;
+}
+
+enum product_type b1x5v2_board_type(void)
+{
+	struct udevice *bus = NULL;
+	struct udevice *dev = NULL;
+	char model[11] = {0};
+	int err;
+	int retry;
+
+	err = uclass_get_device_by_name(UCLASS_I2C, "i2c at 21a8000", &bus);
+	if (err) {
+		printf("Could not get I2C bus: %d\n", err);
+		return PRODUCT_TYPE_INVALID;
+	}
+
+	err = dm_i2c_probe(bus, 0x41, 0, &dev);
+	if (!err && dev) { /* Ilitek Touchscreen */
+		if (b1x5v2_board_is_p_model()) {
+			return PRODUCT_TYPE_B105PV2;
+		} else {
+			return PRODUCT_TYPE_B105V2;
+		}
+	}
+
+	err = dm_i2c_probe(bus, 0x2a, 0, &dev);
+	if (err || !dev) {
+		printf("Could not find touchscreen: %d\n", err);
+		return PRODUCT_TYPE_INVALID;
+	}
+
+	for (retry = 0; retry < 3; ++retry) {
+		err = eeti_touch_get_model(dev, model);
+		if (!err)
+			break;
+		printf("Retry %d read EETI touchscreen model: %d\n", retry + 1, err);
+	}
+	if (err) {
+		printf("Could not read EETI touchscreen model: %d\n", err);
+		return PRODUCT_TYPE_INVALID;
+	}
+
+	if (!strcmp(model, "Orion_1320")) { /* EETI EXC80H60 */
+		if (b1x5v2_board_is_p_model()) {
+			return PRODUCT_TYPE_B125PV2;
+		} else {
+			return PRODUCT_TYPE_B125V2;
+		}
+	} else if (!strcmp(model, "Orion_1343")) { /* EETI EXC80H84 */
+		return PRODUCT_TYPE_B155V2;
+	}
+
+	printf("Unknown EETI touchscreen model: %s\n", model);
+	return PRODUCT_TYPE_INVALID;
+}
+
+void set_env_per_board_type(enum product_type type)
+{
+	switch (type) {
+	case PRODUCT_TYPE_B105V2:
+		env_set("resolution", "1280x800");
+		env_set("devicetype", "B105v2");
+		env_set("fdtfile", "imx6dl-b105v2.dtb");
+		break;
+	case PRODUCT_TYPE_B105PV2:
+		env_set("resolution", "1280x800");
+		env_set("devicetype", "B105Pv2");
+		env_set("fdtfile", "imx6dl-b105pv2.dtb");
+		break;
+	case PRODUCT_TYPE_B125V2:
+		env_set("resolution", "1280x800");
+		env_set("devicetype", "B125v2");
+		env_set("fdtfile", "imx6dl-b125v2.dtb");
+		break;
+	case PRODUCT_TYPE_B125PV2:
+		env_set("resolution", "1280x800");
+		env_set("devicetype", "B125Pv2");
+		env_set("fdtfile", "imx6dl-b125pv2.dtb");
+		break;
+	case PRODUCT_TYPE_B155V2:
+		env_set("resolution", "1366x768");
+		env_set("devicetype", "B155v2");
+		env_set("fdtfile", "imx6dl-b155v2.dtb");
+		break;
+	default:
+		break;
+	}
+}
+
+int b1x5v2_board_type_autodetect(void)
+{
+	enum product_type product = b1x5v2_board_type();
+	if (product != PRODUCT_TYPE_INVALID) {
+		set_env_per_board_type(product);
+		return 0;
+	}
+	return -1;
+}
+
+/*
+ * Extracts MAC and product information from the VPD.
+ */
+static int vpd_callback(struct vpd_cache *vpd, u8 id, u8 version, u8 type,
+			size_t size, u8 const *data)
+{
+	if (type == VPD_TYPE_INVALID)
+		return 0;
+
+	if (id == VPD_BLOCK_HWID && version == 1 && size >= 1) {
+		vpd->product_id = data[0];
+	} else if (id == VPD_BLOCK_NETWORK && version == 1) {
+		if (size >= VPD_MAC_ADDRESS_LENGTH) {
+			memcpy(vpd->mac, data, VPD_MAC_ADDRESS_LENGTH);
+			vpd->flags |= VPD_FLAG_VALID_MAC;
+		}
+	}
+
+	return 0;
+}
+
+int read_spi_vpd(struct vpd_cache *cache,
+		 int (*process_block)(struct vpd_cache *, u8 id, u8 version,
+				      u8 type, size_t size, u8 const *data))
+{
+	static const int size = B1X5V2_GE_VPD_SIZE;
+	struct udevice *dev;
+	int ret;
+	u8 *data;
+
+	ret = uclass_get_device_by_name(UCLASS_SPI_FLASH, "m25p80 at 0", &dev);
+	if (ret)
+		return ret;
+
+	data = malloc(size);
+	if (!data)
+		return -ENOMEM;
+
+	ret = spi_flash_read_dm(dev, B1X5V2_GE_VPD_OFFSET, size, data);
+	if (ret) {
+		free(data);
+		return ret;
+	}
+
+	ret = vpd_reader(size, data, cache, process_block);
+
+	free(data);
+
+	return ret;
+}
+
+int board_init(void)
+{
+	if (!read_spi_vpd(&vpd, vpd_callback)) {
+		vpd.is_read = true;
+	}
+
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+	setup_display();
+
+	return 0;
+}
+
+void init_bootcause(void)
+{
+	const char *cause;
+
+	/* We care about WDOG only, treating everything else as
+	 * a power-on-reset.
+	 */
+	if (get_imx_reset_cause() & 0x0010)
+		cause = "WDOG";
+	else
+		cause = "POR";
+
+	env_set("bootcause", cause);
+}
+
+int misc_init_r(void)
+{
+	init_bootcause();
+
+	return 0;
+}
+
+#define M41T62_REG_FLAGS	0xf
+#define M41T62_FLAGS_OF		(1 << 2)
+void check_time(void)
+{
+	struct udevice *rtc = NULL;
+	struct rtc_time tm;
+	u8 val;
+	int ret;
+
+	ret = uclass_get_device_by_name(UCLASS_RTC, "m41t62 at 68", &rtc);
+	if (ret) {
+		printf("Could not get RTC: %d\n", ret);
+		env_set("rtc_status", "FAIL");
+		return;
+	}
+
+	ret = dm_i2c_read(rtc, M41T62_REG_FLAGS, &val, sizeof(val));
+	if (ret) {
+		printf("Could not read RTC register: %d\n", ret);
+		env_set("rtc_status", "FAIL");
+		return;
+	}
+
+	ret = dm_rtc_reset(rtc);
+	if (ret) {
+		printf("Could not reset RTC: %d\n", ret);
+		env_set("rtc_status", "FAIL");
+		return;
+	}
+
+	if (val & M41T62_FLAGS_OF) {
+		env_set("rtc_status", "STOP");
+		return;
+	}
+
+	ret = dm_rtc_get(rtc, &tm);
+	if (ret) {
+		printf("Could not read RTC: %d\n", ret);
+		env_set("rtc_status", "FAIL");
+		return;
+	}
+
+	if (tm.tm_year > 2037) {
+		tm.tm_sec  = 0;
+		tm.tm_min  = 0;
+		tm.tm_hour = 0;
+		tm.tm_mday = 1;
+		tm.tm_wday = 2;
+		tm.tm_mon  = 1;
+		tm.tm_year = 2036;
+
+		ret = dm_rtc_set(rtc, &tm);
+		if (ret) {
+			printf("Could not update RTC: %d\n", ret);
+			env_set("rtc_status", "FAIL");
+			return;
+		}
+
+		printf("RTC behind 2037, capped to 2036 for userspace handling\n");
+		env_set("rtc_status", "2038");
+		return;
+	}
+
+	env_set("rtc_status", "OK");
+}
+
+static void process_vpd(struct vpd_cache *vpd)
+{
+	if (!vpd->is_read) {
+		printf("VPD wasn't read\n");
+		return;
+	}
+
+	if (vpd->flags & VPD_FLAG_VALID_MAC) {
+		eth_env_set_enetaddr_by_index("eth", 0, vpd->mac);
+		env_set("ethact", "eth0");
+	}
+}
+
+int board_late_init(void)
+{
+	process_vpd(&vpd);
+
+	if (vpd.product_id >= PRODUCT_TYPE_B105V2 &&
+	    vpd.product_id <= PRODUCT_TYPE_B155V2) {
+		set_env_per_board_type((enum product_type)vpd.product_id);
+	} else {
+		b1x5v2_board_type_autodetect();
+	}
+
+	printf("Board: GE %s\n", env_get("devicetype"));
+
+	check_time();
+
+	return 0;
+}
+
+#ifdef CONFIG_OF_BOARD_SETUP
+int ft_board_setup(void *blob, bd_t *bd)
+{
+	char *rtc_status = env_get("rtc_status");
+
+	fdt_setprop(blob, 0, "ge,boot-ver", version_string,
+	                                    strlen(version_string) + 1);
+	fdt_setprop(blob, 0, "ge,rtc-status", rtc_status,
+	                                    strlen(rtc_status) + 1);
+
+	return 0;
+}
+#endif
+
+static int do_b1x5v2_autodetect(struct cmd_tbl *cmdtp, int flag, int argc, char * const argv[])
+{
+	int err;
+
+	err = b1x5v2_board_type_autodetect();
+	if (!err)
+		printf("Identified %s\n", env_get("devicetype"));
+
+	return 0;
+}
+
+U_BOOT_CMD(
+       autodetect_devtype, 1,      1,      do_b1x5v2_autodetect,
+       "autodetect b1x5v2 device type",
+       ""
+);
+
+#endif // CONFIG_SPL_BUILD
diff --git a/board/ge/b1x5v2/spl.c b/board/ge/b1x5v2/spl.c
new file mode 100644
index 000000000000..2e6f905219fe
--- /dev/null
+++ b/board/ge/b1x5v2/spl.c
@@ -0,0 +1,587 @@
+/*
+ * GE b1x5v2 - QMX6 SPL
+ *
+ * Copyright 2013, Adeneo Embedded <www.adeneo-embedded.com>
+ * Copyright 2018-2020 GE Inc.
+ * Copyright 2018-2020 Collabora Ltd.
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <init.h>
+#include <spi.h>
+#include <spi_flash.h>
+#include <spl.h>
+
+#if defined(CONFIG_SPL_BUILD)
+
+#include <asm/arch/mx6-ddr.h>
+
+#define IMX6DQ_DRIVE_STRENGTH_40_OHM		0x30
+#define IMX6DQ_DRIVE_STRENGTH_48_OHM		0x28
+#define IMX6DQ_DRIVE_STRENGTH			IMX6DQ_DRIVE_STRENGTH_40_OHM
+
+#define QMX6_DDR_PKE_DISABLED			0x00000000
+#define QMX6_DDR_ODT_60_OHM			(2 << 16)
+#define QMX6_DDR_TYPE_DDR3			0x000c0000
+
+#define QMX6_DRAM_SDCKE_PULLUP_100K		0x00003000
+#define QMX6_DRAM_SDBA2_PULLUP_NONE		0x00000000
+
+#define SPI_PAD_CTRL (PAD_CTL_HYS |				\
+	PAD_CTL_SPEED_MED |		\
+	PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+
+#define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |			\
+	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define SPI1_CS0 IMX_GPIO_NR(3, 19)
+#define POWEROFF IMX_GPIO_NR(4, 25)
+
+static iomux_v3_cfg_t const poweroff_pads[] = {
+	IOMUX_PADS(PAD_DISP0_DAT4__GPIO4_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+};
+
+static iomux_v3_cfg_t const uart2_pads[] = {
+	IOMUX_PADS(PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
+	IOMUX_PADS(PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
+};
+
+static iomux_v3_cfg_t const uart3_pads[] = {
+	IOMUX_PADS(PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
+	IOMUX_PADS(PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
+};
+
+static iomux_v3_cfg_t const ecspi1_pads[] = {
+	IOMUX_PADS(PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL)),
+	IOMUX_PADS(PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL)),
+	IOMUX_PADS(PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL)),
+	IOMUX_PADS(PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+};
+
+static struct mx6dq_iomux_ddr_regs mx6q_ddr_ioregs = {
+	.dram_sdclk_0 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_sdclk_1 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_cas = IMX6DQ_DRIVE_STRENGTH,
+	.dram_ras = IMX6DQ_DRIVE_STRENGTH,
+	.dram_reset = IMX6DQ_DRIVE_STRENGTH,
+	.dram_sdcke0 = QMX6_DRAM_SDCKE_PULLUP_100K,
+	.dram_sdcke1 = QMX6_DRAM_SDCKE_PULLUP_100K,
+	.dram_sdba2 = QMX6_DRAM_SDBA2_PULLUP_NONE,
+	.dram_sdodt0 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_sdodt1 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_sdqs0 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_sdqs1 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_sdqs2 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_sdqs3 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_sdqs4 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_sdqs5 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_sdqs6 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_sdqs7 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_dqm0 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_dqm1 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_dqm2 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_dqm3 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_dqm4 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_dqm5 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_dqm6 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_dqm7 = IMX6DQ_DRIVE_STRENGTH,
+};
+
+static const struct mx6sdl_iomux_ddr_regs mx6dl_ddr_ioregs = {
+	.dram_sdclk_0 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_sdclk_1 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_cas = IMX6DQ_DRIVE_STRENGTH,
+	.dram_ras = IMX6DQ_DRIVE_STRENGTH,
+	.dram_reset = IMX6DQ_DRIVE_STRENGTH,
+	.dram_sdcke0 = QMX6_DRAM_SDCKE_PULLUP_100K,
+	.dram_sdcke1 = QMX6_DRAM_SDCKE_PULLUP_100K,
+	.dram_sdba2 = QMX6_DRAM_SDBA2_PULLUP_NONE,
+	.dram_sdodt0 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_sdodt1 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_sdqs0 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_sdqs1 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_sdqs2 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_sdqs3 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_sdqs4 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_sdqs5 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_sdqs6 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_sdqs7 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_dqm0 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_dqm1 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_dqm2 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_dqm3 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_dqm4 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_dqm5 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_dqm6 = IMX6DQ_DRIVE_STRENGTH,
+	.dram_dqm7 = IMX6DQ_DRIVE_STRENGTH,
+};
+
+static struct mx6dq_iomux_grp_regs mx6q_grp_ioregs = {
+	.grp_ddr_type = QMX6_DDR_TYPE_DDR3,
+	.grp_ddrmode_ctl = QMX6_DDR_ODT_60_OHM,
+	.grp_ddrpke = QMX6_DDR_PKE_DISABLED,
+	.grp_addds = IMX6DQ_DRIVE_STRENGTH,
+	.grp_ctlds = IMX6DQ_DRIVE_STRENGTH,
+	.grp_ddrmode = QMX6_DDR_ODT_60_OHM,
+	.grp_b0ds = IMX6DQ_DRIVE_STRENGTH,
+	.grp_b1ds = IMX6DQ_DRIVE_STRENGTH,
+	.grp_b2ds = IMX6DQ_DRIVE_STRENGTH,
+	.grp_b3ds = IMX6DQ_DRIVE_STRENGTH,
+	.grp_b4ds = IMX6DQ_DRIVE_STRENGTH,
+	.grp_b5ds = IMX6DQ_DRIVE_STRENGTH,
+	.grp_b6ds = IMX6DQ_DRIVE_STRENGTH,
+	.grp_b7ds = IMX6DQ_DRIVE_STRENGTH,
+};
+
+static const struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = {
+	.grp_ddr_type = QMX6_DDR_TYPE_DDR3,
+	.grp_ddrmode_ctl = QMX6_DDR_ODT_60_OHM,
+	.grp_ddrpke = QMX6_DDR_PKE_DISABLED,
+	.grp_addds = IMX6DQ_DRIVE_STRENGTH,
+	.grp_ctlds = IMX6DQ_DRIVE_STRENGTH,
+	.grp_ddrmode = QMX6_DDR_ODT_60_OHM,
+	.grp_b0ds = IMX6DQ_DRIVE_STRENGTH,
+	.grp_b1ds = IMX6DQ_DRIVE_STRENGTH,
+	.grp_b2ds = IMX6DQ_DRIVE_STRENGTH,
+	.grp_b3ds = IMX6DQ_DRIVE_STRENGTH,
+	.grp_b4ds = IMX6DQ_DRIVE_STRENGTH,
+	.grp_b5ds = IMX6DQ_DRIVE_STRENGTH,
+	.grp_b6ds = IMX6DQ_DRIVE_STRENGTH,
+	.grp_b7ds = IMX6DQ_DRIVE_STRENGTH,
+};
+
+const struct mx6_mmdc_calibration mx6q_mmcd_calib = {
+	.p0_mpwldectrl0 =  0x0016001A,
+	.p0_mpwldectrl1 =  0x0023001C,
+	.p1_mpwldectrl0 =  0x0028003A,
+	.p1_mpwldectrl1 =  0x001F002C,
+	.p0_mpdgctrl0 =  0x43440354,
+	.p0_mpdgctrl1 =  0x033C033C,
+	.p1_mpdgctrl0 =  0x43300368,
+	.p1_mpdgctrl1 =  0x03500330,
+	.p0_mprddlctl =  0x3228242E,
+	.p1_mprddlctl =  0x2C2C2636,
+	.p0_mpwrdlctl =  0x36323A38,
+	.p1_mpwrdlctl =  0x42324440,
+};
+
+const struct mx6_mmdc_calibration mx6q_2g_mmcd_calib = {
+	.p0_mpwldectrl0 =  0x00080016,
+	.p0_mpwldectrl1 =  0x001D0016,
+	.p1_mpwldectrl0 =  0x0018002C,
+	.p1_mpwldectrl1 =  0x000D001D,
+	.p0_mpdgctrl0 =    0x43200334,
+	.p0_mpdgctrl1 =    0x0320031C,
+	.p1_mpdgctrl0 =    0x0344034C,
+	.p1_mpdgctrl1 =    0x03380314,
+	.p0_mprddlctl =    0x3E36383A,
+	.p1_mprddlctl =    0x38363240,
+	.p0_mpwrdlctl =	   0x36364238,
+	.p1_mpwrdlctl =    0x4230423E,
+};
+
+const struct mx6_mmdc_calibration mx6q_4g_mmcd_calib = {
+	.p0_mpwldectrl0 =  0x00180018,
+	.p0_mpwldectrl1 =  0x00220018,
+	.p1_mpwldectrl0 =  0x00330046,
+	.p1_mpwldectrl1 =  0x002B003D,
+	.p0_mpdgctrl0 =    0x4344034C,
+	.p0_mpdgctrl1 =    0x033C033C,
+	.p1_mpdgctrl0 =    0x03700374,
+	.p1_mpdgctrl1 =    0x03600338,
+	.p0_mprddlctl =    0x443E3E40,
+	.p1_mprddlctl =    0x423E3E48,
+	.p0_mpwrdlctl =	   0x3C3C4442,
+	.p1_mpwrdlctl =    0x46384C46,
+};
+
+static const struct mx6_mmdc_calibration mx6s_mmcd_calib = {
+	.p0_mpwldectrl0 =  0x00480049,
+	.p0_mpwldectrl1 =  0x00410044,
+	.p0_mpdgctrl0 =    0x42480248,
+	.p0_mpdgctrl1 =    0x023C023C,
+	.p0_mprddlctl =    0x40424644,
+	.p0_mpwrdlctl =    0x34323034,
+};
+
+static const struct mx6_mmdc_calibration mx6s_2g_mmcd_calib = {
+	.p0_mpwldectrl0 =  0x00450048,
+	.p0_mpwldectrl1 =  0x003B003F,
+	.p0_mpdgctrl0 =    0x424C0248,
+	.p0_mpdgctrl1 =    0x0234023C,
+	.p0_mprddlctl =    0x40444848,
+	.p0_mpwrdlctl =    0x38363232,
+};
+
+static const struct mx6_mmdc_calibration mx6dl_mmcd_calib = {
+	.p0_mpwldectrl0 =  0x0043004B,
+	.p0_mpwldectrl1 =  0x003A003E,
+	.p1_mpwldectrl0 =  0x0047004F,
+	.p1_mpwldectrl1 =  0x004E0061,
+	.p0_mpdgctrl0 =    0x42500250,
+	.p0_mpdgctrl1 =	   0x0238023C,
+	.p1_mpdgctrl0 =    0x42640264,
+	.p1_mpdgctrl1 =    0x02500258,
+	.p0_mprddlctl =    0x40424846,
+	.p1_mprddlctl =    0x46484842,
+	.p0_mpwrdlctl =    0x38382C30,
+	.p1_mpwrdlctl =    0x34343430,
+};
+
+static const struct mx6_mmdc_calibration mx6dl_2g_mmcd_calib = {
+	.p0_mpwldectrl0 =  0x00450045,
+	.p0_mpwldectrl1 =  0x00390043,
+	.p1_mpwldectrl0 =  0x0049004D,
+	.p1_mpwldectrl1 =  0x004E0061,
+	.p0_mpdgctrl0 =    0x4240023C,
+	.p0_mpdgctrl1 =	   0x0228022C,
+	.p1_mpdgctrl0 =    0x02400244,
+	.p1_mpdgctrl1 =    0x02340238,
+	.p0_mprddlctl =    0x42464648,
+	.p1_mprddlctl =    0x4446463C,
+	.p0_mpwrdlctl =    0x3C38323A,
+	.p1_mpwrdlctl =    0x34323430,
+};
+
+static struct mx6_ddr3_cfg mem_ddr_2g = {
+	.mem_speed = 1600,
+	.density = 2,
+	.width = 16,
+	.banks = 8,
+	.rowaddr = 14,
+	.coladdr = 10,
+	.pagesz = 2,
+	.trcd = 1310,
+	.trcmin = 4875,
+	.trasmin = 3500,
+};
+
+static struct mx6_ddr3_cfg mem_ddr_4g = {
+	.mem_speed = 1600,
+	.density = 4,
+	.width = 16,
+	.banks = 8,
+	.rowaddr = 15,
+	.coladdr = 10,
+	.pagesz = 2,
+	.trcd = 1310,
+	.trcmin = 4875,
+	.trasmin = 3500,
+};
+
+static struct mx6_ddr3_cfg mem_ddr_8g = {
+	.mem_speed = 1600,
+	.density = 8,
+	.width = 16,
+	.banks = 8,
+	.rowaddr = 16,
+	.coladdr = 10,
+	.pagesz = 2,
+	.trcd = 1310,
+	.trcmin = 4875,
+	.trasmin = 3500,
+};
+
+static void spl_dram_init(u8 width, u32 memsize) {
+	struct mx6_ddr_sysinfo sysinfo = {
+		 /* width of data bus: 0=16, 1=32, 2=64 */
+		.dsize		= width / 32,
+		/* config for full 4GB range so that get_mem_size() works */
+		.cs_density	= 32,	/* 32Gb per CS */
+
+		.ncs = 1,
+		.cs1_mirror = 0,
+		.rtt_wr = 2,
+		.rtt_nom = 2,
+		.walat = 0,
+		.ralat = 5,
+		.mif3_mode = 3,
+		.bi_on = 1,
+		.sde_to_rst = 0x0d,
+		.rst_to_cke = 0x20,
+	};
+
+	if (is_cpu_type(MXC_CPU_MX6SOLO)) {
+		sysinfo.walat = 1;
+		mx6sdl_dram_iocfg(width, &mx6dl_ddr_ioregs, &mx6sdl_grp_ioregs);
+
+		switch(memsize) {
+		case 512:
+			mx6_dram_cfg(&sysinfo, &mx6s_2g_mmcd_calib, &mem_ddr_2g);
+			break;
+		default:
+			mx6_dram_cfg(&sysinfo, &mx6s_mmcd_calib, &mem_ddr_4g);
+			break;
+		}
+	} else if (is_cpu_type(MXC_CPU_MX6DL)) {
+		sysinfo.walat = 1;
+		mx6sdl_dram_iocfg(width, &mx6dl_ddr_ioregs, &mx6sdl_grp_ioregs);
+
+		switch(memsize) {
+		case 2048:
+			mx6_dram_cfg(&sysinfo, &mx6dl_2g_mmcd_calib, &mem_ddr_4g);
+			break;
+		default:
+			mx6_dram_cfg(&sysinfo, &mx6dl_mmcd_calib, &mem_ddr_2g);
+			break;
+		}
+	} else if (is_cpu_type(MXC_CPU_MX6Q)) {
+		mx6dq_dram_iocfg(width, &mx6q_ddr_ioregs, &mx6q_grp_ioregs);
+
+		switch(memsize) {
+		case 4096:
+			sysinfo.cs_density = 16;
+			sysinfo.ncs = 2;
+			mx6_dram_cfg(&sysinfo, &mx6q_4g_mmcd_calib, &mem_ddr_8g);
+			break;
+		case 2048:
+			mx6_dram_cfg(&sysinfo, &mx6q_2g_mmcd_calib, &mem_ddr_4g);
+			break;
+		default:
+			mx6_dram_cfg(&sysinfo, &mx6q_mmcd_calib, &mem_ddr_2g);
+			break;
+		}
+	}
+}
+
+/* Define a minimal structure so that the part number can be read via SPL */
+#define CFG_MFG_ADDR_OFFSET	(spi->size - SZ_16K)
+struct mfgdata {
+	unsigned char tsize;
+	/* size of checksummed part in bytes */
+	unsigned char ckcnt;
+	/* checksum corrected byte */
+	unsigned char cksum;
+	/* decimal serial number, packed BCD */
+	unsigned char serial[6];
+	 /* part number, right justified, ASCII */
+	unsigned char pn[16];
+};
+
+static void conv_ascii(unsigned char *dst, unsigned char *src, int len)
+{
+	int remain = len;
+	unsigned char *sptr = src;
+	unsigned char *dptr = dst;
+
+	while (remain) {
+		if (*sptr) {
+			*dptr = *sptr;
+			dptr++;
+		}
+		sptr++;
+		remain--;
+	}
+	*dptr = 0x0;
+}
+
+/*
+ * Returns the total size of the memory [in MB] the board is equipped with
+ *
+ * This is determined via the partnumber which is stored in the
+ * congatec manufacturing area
+ */
+static int get_boardmem_size(struct spi_flash *spi)
+{
+	int ret;
+	int i;
+	int arraysize;
+	char buf[sizeof(struct mfgdata)];
+	struct mfgdata *data = (struct mfgdata *)buf;
+	unsigned char outbuf[32];
+	char partnumbers_2g[4][7] = { "016104", "016105", "016304", "016305" };
+	char partnumbers_4g[2][7] = { "016308", "016318" };
+	char partnumbers_512m[2][7] = { "016203", "616300" };
+
+	ret = spi_flash_read(spi, CFG_MFG_ADDR_OFFSET, sizeof(struct mfgdata),
+			     buf);
+	if (ret)
+		return 1024; /* default to 1GByte in case of error */
+
+	conv_ascii(outbuf, data->pn, sizeof(data->pn));
+
+	printf("Detected Congatec QMX6 SOM: %s\n", outbuf);
+
+	/* congatec PN 016104, 016105, 016304, 016305 have 2GiB of RAM */
+	arraysize = sizeof(partnumbers_2g) / sizeof(partnumbers_2g[0]);
+	for (i=0; i < arraysize; i++) {
+		if (!memcmp(outbuf,partnumbers_2g[i],6))
+			return 2048;
+	}
+
+	/* congatec PN 016308, 016318 have 4GiB of RAM */
+	arraysize = sizeof(partnumbers_4g) / sizeof(partnumbers_4g[0]);
+	for (i=0; i < arraysize; i++) {
+		if (!memcmp(outbuf,partnumbers_4g[i],6))
+			return 4096;
+	}
+
+	/* congatec PN 016203, 616300 has 512MiB of RAM */
+	arraysize = sizeof(partnumbers_512m) / sizeof(partnumbers_512m[0]);
+	for (i=0; i < arraysize; i++) {
+		if (!memcmp(outbuf,partnumbers_512m[i],6))
+			return 512;
+	}
+
+	/* default to 1GByte */
+	return 1024;
+}
+
+void reset_cpu(ulong addr)
+{
+}
+
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+	if (bus == 0 && cs == 0)
+		return (SPI1_CS0);
+	else
+		return -1;
+}
+
+static void memory_init(void) {
+	struct spi_flash *spi;
+	u8 width;
+	u32 size;
+
+	SETUP_IOMUX_PADS(ecspi1_pads);
+	gpio_direction_output(SPI1_CS0, 0);
+
+	spi = spi_flash_probe(CONFIG_ENV_SPI_BUS,
+			      CONFIG_ENV_SPI_CS,
+			      CONFIG_ENV_SPI_MAX_HZ, CONFIG_ENV_SPI_MODE);
+	if (!spi)
+		panic("Cannot identify board type: SPI-NOR flash module not detected\n");
+
+	/* lock manufacturer area */
+	spi_flash_protect(spi, CFG_MFG_ADDR_OFFSET, SZ_16K, true);
+
+	width = is_cpu_type(MXC_CPU_MX6SOLO) ? 32 : 64;
+	size = get_boardmem_size(spi);
+	printf("Detected Memory Size: %u\n", size);
+
+	spl_dram_init(width, size);
+}
+
+static void ccgr_init(void)
+{
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	static const uint32_t ccgr0 =
+		MXC_CCM_CCGR0_AIPS_TZ1_MASK |
+		MXC_CCM_CCGR0_AIPS_TZ2_MASK |
+		MXC_CCM_CCGR0_APBHDMA_MASK |
+		MXC_CCM_CCGR0_CAAM_SECURE_MEM_MASK |
+		MXC_CCM_CCGR0_CAAM_WRAPPER_ACLK_MASK |
+		MXC_CCM_CCGR0_CAAM_WRAPPER_IPG_MASK |
+		MXC_CCM_CCGR0_CHEETAH_DBG_CLK_MASK;
+
+	static const uint32_t ccgr1 =
+		MXC_CCM_CCGR1_ECSPI1S_MASK |
+		MXC_CCM_CCGR1_ENET_MASK |
+		MXC_CCM_CCGR1_EPIT1S_MASK |
+		MXC_CCM_CCGR1_EPIT2S_MASK |
+		MXC_CCM_CCGR1_GPT_BUS_MASK;
+
+	static const uint32_t ccgr2 =
+		MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK |
+		MXC_CCM_CCGR2_IPMUX1_MASK |
+		MXC_CCM_CCGR2_IPMUX2_MASK |
+		MXC_CCM_CCGR2_IPMUX3_MASK |
+		MXC_CCM_CCGR2_IPSYNC_IP2APB_TZASC1_IPGS_MASK |
+		MXC_CCM_CCGR2_IPSYNC_IP2APB_TZASC2_IPG_MASK |
+		MXC_CCM_CCGR2_IPSYNC_VDOA_IPG_MASTER_CLK_MASK;
+
+	static const uint32_t ccgr3 =
+		MXC_CCM_CCGR3_MMDC_CORE_ACLK_FAST_CORE_P0_MASK |
+		MXC_CCM_CCGR3_MMDC_CORE_ACLK_FAST_CORE_P1_MASK |
+		MXC_CCM_CCGR3_MMDC_CORE_IPG_CLK_P0_MASK |
+		MXC_CCM_CCGR3_MMDC_CORE_IPG_CLK_P1_MASK |
+		MXC_CCM_CCGR3_OCRAM_MASK;
+
+	static const uint32_t ccgr4 =
+		MXC_CCM_CCGR4_PL301_MX6QFAST1_S133_MASK |
+		MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_MASK |
+		MXC_CCM_CCGR4_PL301_MX6QPER2_MAINCLK_ENABLE_MASK |
+		MXC_CCM_CCGR4_PWM1_MASK |
+		MXC_CCM_CCGR4_PWM2_MASK |
+		MXC_CCM_CCGR4_PWM3_MASK |
+		MXC_CCM_CCGR4_PWM4_MASK;
+
+	static const uint32_t ccgr5 =
+		MXC_CCM_CCGR5_ROM_MASK |
+		MXC_CCM_CCGR5_SDMA_MASK |
+		MXC_CCM_CCGR5_UART_MASK |
+		MXC_CCM_CCGR5_UART_SERIAL_MASK;
+
+	static const uint32_t ccgr6 =
+		MXC_CCM_CCGR6_USBOH3_MASK |
+		MXC_CCM_CCGR6_USDHC1_MASK |
+		MXC_CCM_CCGR6_USDHC2_MASK |
+		MXC_CCM_CCGR6_SIM1_CLK_MASK |
+		MXC_CCM_CCGR6_SIM2_CLK_MASK;
+
+	writel(ccgr0, &ccm->CCGR0);
+	writel(ccgr1, &ccm->CCGR1);
+	writel(ccgr2, &ccm->CCGR2);
+	writel(ccgr3, &ccm->CCGR3);
+	writel(ccgr4, &ccm->CCGR4);
+	writel(ccgr5, &ccm->CCGR5);
+	writel(ccgr6, &ccm->CCGR6);
+}
+
+void board_init_f(ulong dummy)
+{
+	/* setup clock gating */
+	ccgr_init();
+
+	/* setup AIPS and disable watchdog */
+	arch_cpu_init();
+
+	/* setup AXI */
+	gpr_init();
+
+	/*
+	 * setup poweroff GPIO. This controls system power regulator. Once
+	 * the power button is released this must be enabled to keep system
+	 * running. Not enabling it (or disabling it later) will turn off
+	 * the main system regulator and instantly poweroff the system. We
+	 * do this very early, to reduce the time users have to press the
+	 * power button.
+	 */
+	SETUP_IOMUX_PADS(poweroff_pads);
+	gpio_direction_output(POWEROFF, 1);
+
+	/* setup GP timer */
+	timer_init();
+
+	/* iomux */
+	if (CONFIG_MXC_UART_BASE == UART2_BASE)
+		SETUP_IOMUX_PADS(uart2_pads);
+	else if (CONFIG_MXC_UART_BASE == UART3_BASE)
+		SETUP_IOMUX_PADS(uart3_pads);
+
+	/* UART clocks enabled and gd valid - init serial console */
+	preloader_console_init();
+
+	/* Needed for malloc() [used by SPI] to work in SPL prior to board_init_r() */
+	spl_init();
+
+	/* DDR initialization */
+	memory_init();
+}
+
+void spl_board_prepare_for_boot(void)
+{
+	printf("Load normal U-Boot...\n");
+}
+#endif
diff --git a/configs/ge_b1x5v2_defconfig b/configs/ge_b1x5v2_defconfig
new file mode 100644
index 000000000000..dd375e5b34b1
--- /dev/null
+++ b/configs/ge_b1x5v2_defconfig
@@ -0,0 +1,148 @@
+CONFIG_DEFAULT_FDT_FILE="imx6dl-b1x5v2.dtb"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_BCH=y
+CONFIG_SYS_TEXT_BASE=0x17800000
+CONFIG_SPL_TEXT_BASE=0x00908000
+CONFIG_ENV_SIZE=0x2000
+CONFIG_ENV_OFFSET=0xC0000
+CONFIG_ENV_SECT_SIZE=0x10000
+CONFIG_SYS_SPI_U_BOOT_OFFS=0x11400
+CONFIG_TARGET_GE_B1X5V2=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_FIT=y
+CONFIG_BOOTDELAY=0
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
+CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
+CONFIG_SUPPORT_RAW_INITRD=y
+CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_BOOTZ=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_NET=y
+CONFIG_OF_LIBFDT=y
+CONFIG_SYS_I2C_MXC=y
+CONFIG_MXC_GPIO=y
+CONFIG_CMD_GPIO=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_ATHEROS=y
+CONFIG_FEC_MXC=y
+CONFIG_MII=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_MXC_UART=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_MXC=y
+# CONFIG_DEBUG_UART_BASE=0x21e8000
+CONFIG_DEBUG_UART_BASE=0x21ec000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_SPL=y
+CONFIG_SPL_GPIO_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SPL_LIBDISK_SUPPORT=y
+CONFIG_SPL_SPI_SUPPORT=y
+CONFIG_SPL_SPI_FLASH_SUPPORT=y
+CONFIG_SPL_SPI_LOAD=y
+CONFIG_SPL_USB_GADGET=y
+CONFIG_SPL_USB_SDP_SUPPORT=y
+CONFIG_FSL_ESDHC=y
+CONFIG_SPI=y
+CONFIG_MXC_SPI=y
+CONFIG_CMD_SF=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_ENV_SPI_BUS=0
+CONFIG_ENV_SPI_CS=0
+CONFIG_ENV_SPI_MODE=0
+CONFIG_ENV_SPI_MAX_HZ=20000000
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_SST=y
+CONFIG_SPI_FLASH_WINBOND=y
+# CONFIG_GE_RTC is not set
+CONFIG_IMX_THERMAL=y
+CONFIG_WDT=y
+CONFIG_WDT_IMX=y
+CONFIG_WATCHDOG_TIMEOUT_MSECS=30000
+CONFIG_RTC_M41T62=y
+CONFIG_USB=y
+CONFIG_USB_KEYBOARD=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="Congatec"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
+CONFIG_SPL_USB_HOST_SUPPORT=y
+CONFIG_CI_UDC=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_BOUNCE_BUFFER=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_MISC_INIT_R=y
+CONFIG_SF_DEFAULT_MODE=0
+CONFIG_SF_DEFAULT_SPEED=20000000
+CONFIG_VIDEO_IPUV3=y
+CONFIG_BACKLIGHT_PWM=y
+CONFIG_DM=y
+CONFIG_CMD_DM=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx6dl-b1x5v2"
+CONFIG_DM_MMC=y
+CONFIG_BLK=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_I2C_MUX=y
+CONFIG_I2C_MUX_GPIO=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_PFUZE100=y
+CONFIG_DM_SPI=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_DM_ETH=y
+CONFIG_DM_USB=y
+CONFIG_DM_VIDEO=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_DM_PWM=y
+CONFIG_PWM_IMX=y
+CONFIG_DM_RTC=y
+CONFIG_DM_PCA953X=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_SYS_MALLOC_F_LEN=0x4000
+CONFIG_CMD_BOOTCOUNT=y
+CONFIG_BOOTCOUNT_LIMIT=y
+CONFIG_BOOTCOUNT_BOOTLIMIT=10
+CONFIG_DM_BOOTCOUNT=y
+CONFIG_DM_BOOTCOUNT_SPI_FLASH=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_GREPENV=y
+CONFIG_CMD_SNTP=y
+CONFIG_CMD_DNS=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_LED=y
+CONFIG_CMD_BMP=y
+CONFIG_CMD_LOG=y
+CONFIG_CMD_CLS=y
+CONFIG_LOG_MAX_LEVEL=8
+CONFIG_DM_SERIAL=y
+CONFIG_SPECIFY_CONSOLE_INDEX=y
+CONFIG_POWEROFF=y
+CONFIG_POWEROFF_GPIO=y
+CONFIG_CMD_POWEROFF=y
+# CONFIG_SPL_PMIC_CHILDREN is not set
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_SPL_PAYLOAD="u-boot.img"
diff --git a/include/configs/ge_b1x5v2.h b/include/configs/ge_b1x5v2.h
new file mode 100644
index 000000000000..91ad67cfe249
--- /dev/null
+++ b/include/configs/ge_b1x5v2.h
@@ -0,0 +1,125 @@
+/*
+ * GE B1x5v2
+ *
+ * Copyright 2018-2020 GE Inc.
+ * Copyright 2018-2020 Collabora Ltd.
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+#ifndef __GE_B1X5V2_CONFIG_H
+#define __GE_B1X5V2_CONFIG_H
+
+#include "mx6_common.h"
+
+#include "imx6_spl.h"
+#define CONFIG_SPL_TARGET		"u-boot-with-spl.imx"
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(10 * SZ_1M)
+
+/* PWM */
+#define CONFIG_IMX6_PWM_PER_CLK		66000000
+
+/* UART */
+#define CONFIG_MXC_UART_BASE		UART3_BASE
+
+#if CONFIG_MXC_UART_BASE == UART2_BASE
+#define CONSOLE_DEVICE "ttymxc1" /* System on Module debug connector */
+#else
+#define CONSOLE_DEVICE "ttymxc2" /* Base board debug connector */
+#endif
+
+/* USB */
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORTSC		(PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS		0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 /* Enabled USB controller number */
+#define CONFIG_USBD_HS
+
+/* Video */
+#define CONFIG_HIDE_LOGO_VERSION
+#define CONFIG_IMX_VIDEO_SKIP
+
+/* Memory */
+#define PHYS_SDRAM		       MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE	       PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* Command definition */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"image=/boot/fitImage\0" \
+	"fdt_addr_r=0x18000000\0" \
+	"splash_addr_r=0x20000000\0" \
+	"mmcdev=2\0" \
+	"mmcpart=1\0" \
+	"console=console="CONSOLE_DEVICE",115200\0" \
+	"quiet=quiet loglevel=0\0" \
+	"rootdev=/dev/mmcblk1p\0" \
+	"setargs=setenv bootargs ${console} ${quiet} ${fsckforcerepair} " \
+		"bootcause=${bootcause} vt.global_cursor_default=0 vt.cur_default=1 " \
+		"root=${rootdev}${mmcpart} video=HDMI-A-1:${resolution} rootwait ro\0" \
+	"loadimage=load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+	"showsplashscreen=load mmc ${mmcdev}:${mmcpart} ${splash_addr_r} /boot/splashscreen-${resolution}.bmp; " \
+		"bmp display ${splash_addr_r};\0" \
+	"setconfidx=" \
+		"if test \"${devicetype}\" = \"B105v2\"; then " \
+			"setenv confidx 1; " \
+		"elif test \"${devicetype}\" = \"B125v2\"; then " \
+			"setenv confidx 2; " \
+		"elif test \"${devicetype}\" = \"B155v2\"; then " \
+			"setenv confidx 3; " \
+		"elif test \"${devicetype}\" = \"B105Pv2\"; then " \
+			"setenv confidx 4; " \
+		"elif test \"${devicetype}\" = \"B125Pv2\"; then " \
+			"setenv confidx 5; " \
+		"fi;\0" \
+	"set_default_type=setenv devicetype B155v2; setenv resolution 1366x768;" \
+		"setenv fdtfile imx6dl-b155v2.dtb; run setconfidx;\0" \
+	"checkconfidx=env exists confidx || run set_default_type;\0" \
+	"checkfsckforcerepair=" \
+		"if test \"${bootcount}\" > \"3\" ; then " \
+			"setenv fsckforcerepair fsck.repair=1; " \
+		"fi;\0" \
+	"helix=run setconfidx; run checkconfidx; run checkfsckforcerepair; run setargs; " \
+		"regulator dev LED_VCC; regulator enable; " \
+		"regulator dev 5V0_AUDIO; regulator enable; " \
+		"bootm ${loadaddr}#conf@${confidx};\0" \
+	"failbootcmd=" \
+		"echo reached failbootcmd;" \
+		"cls; setcurs 5 4; " \
+		"lcdputs \"Monitor failed to start. Try again, or contact GE Service for support.\"; " \
+		"bootcount reset; \0" \
+	"hasfirstboot=" \
+		"load mmc ${mmcdev}:${mmcpart} ${loadaddr} " \
+		"/boot/bootcause/firstboot;\0" \
+	"swappartitions=" \
+		"setexpr mmcpart 3 - ${mmcpart};\0" \
+	"doboot=" \
+		"echo Booting from mmc:${mmcdev}:${mmcpart} ...; " \
+		"run helix;\0" \
+	"altbootcmd=" \
+		"setenv mmcpart 1; run hasfirstboot || setenv mmcpart 2; " \
+		"run hasfirstboot || setenv mmcpart 0; " \
+		"if test ${mmcpart} != 0; then " \
+			"setenv bootcause REVERT; " \
+			"run swappartitions loadimage doboot; " \
+		"fi; " \
+		"run failbootcmd\0" \
+	"tryboot=" \
+		"setenv mmcpart 1; run hasfirstboot || setenv mmcpart 2; " \
+		"run loadimage || run swappartitions && run loadimage || " \
+		"setenv mmcpart 0 && echo MISSING IMAGE;" \
+		"run showsplashscreen; sleep 1; " \
+		"run doboot; run failbootcmd;\0" \
+
+#define CONFIG_BOOTCOMMAND "run tryboot;"
+
+#endif /* __GE_B1X5V2_CONFIG_H */
