| Message ID | 20200625004851.21056-3-judge.packham@gmail.com |
|---|---|
| State | Accepted |
| Commit | 4182232158bfff7363fa0b4eade360cf50551cb9 |
| Headers | show |
| Series | arm: mvebu: a38x: USB2 serdes changes | expand |
On 25.06.20 02:48, Chris Packham wrote: > When running USB compliance tests on our Armada-385 hardware platforms > we have seen some eye mask violations. Marvell's internal documentation > says: Based on silicon test results, it is recommended to change the > impedance calibration threshold setting to 0x6 prior to calibration. > > Port changes from Marvell's u-boot fork[1] to address this. > > [1] - https://github.com/MarvellEmbeddedProcessors/u-boot-marvell/commit/a6221551 > > Signed-off-by: Chris Packham <judge.packham at gmail.com> Reviewed-by: Stefan Roese <sr at denx.de> Thanks, Stefan > --- > > .../serdes/a38x/high_speed_env_spec.c | 25 ++++++++++++++++--- > 1 file changed, 21 insertions(+), 4 deletions(-) > > diff --git a/arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.c b/arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.c > index d4480622c89c..2454730e6d86 100644 > --- a/arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.c > +++ b/arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.c > @@ -672,12 +672,29 @@ struct op_params usb2_power_up_params[] = { > {0xc200c, 0x0 /*NA*/, 0x1000000, {0x1000000}, 0, 0}, > /* Phy0 register 3 - TX Channel control 0 */ > {0xc400c, 0x0 /*NA*/, 0x1000000, {0x1000000}, 0, 0}, > - /* check PLLCAL_DONE is set and IMPCAL_DONE is set */ > + /* Decrease the amplitude of the low speed eye to meet the spec */ > + {0xc000c, 0x0 /*NA*/, 0xf000, {0x1000}, 0, 0}, > + {0xc200c, 0x0 /*NA*/, 0xf000, {0x1000}, 0, 0}, > + {0xc400c, 0x0 /*NA*/, 0xf000, {0x1000}, 0, 0}, > + /* Change the High speed impedance threshold */ > + {0xc0008, 0x0 /*NA*/, 0x700, {0x600}, 0, 0}, > + {0xc2008, 0x0 /*NA*/, 0x700, {0x600}, 0, 0}, > + {0xc4008, 0x0 /*NA*/, 0x700, {0x600}, 0, 0}, > + /* Change the squelch level of the receiver to meet the receiver electrical measurements (squelch and receiver sensitivity tests) */ > + {0xc0014, 0x0 /*NA*/, 0xf, {0x8}, 0, 0}, > + {0xc2014, 0x0 /*NA*/, 0xf, {0x8}, 0, 0}, > + {0xc4014, 0x0 /*NA*/, 0xf, {0x8}, 0, 0}, > + /* Check PLLCAL_DONE is set and IMPCAL_DONE is set */ > {0xc0008, 0x0 /*NA*/, 0x80800000, {0x80800000}, 1, 1000}, > - /* check REG_SQCAL_DONE is set */ > + /* Check REG_SQCAL_DONE is set */ > {0xc0018, 0x0 /*NA*/, 0x80000000, {0x80000000}, 1, 1000}, > - /* check PLL_READY is set */ > - {0xc0000, 0x0 /*NA*/, 0x80000000, {0x80000000}, 1, 1000} > + /* Check PLL_READY is set */ > + {0xc0000, 0x0 /*NA*/, 0x80000000, {0x80000000}, 1, 1000}, > + /* Start calibrate of high seed impedance */ > + {0xc0008, 0x0 /*NA*/, 0x2000, {0x2000}, 0, 0}, > + {0x0, 0x0 /*NA*/, 0x0, {0x0}, 10, 0}, > + /* De-assert the calibration signal */ > + {0xc0008, 0x0 /*NA*/, 0x2000, {0x0}, 0, 0}, > }; > > /* > Viele Gr??e, Stefan
diff --git a/arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.c b/arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.c index d4480622c89c..2454730e6d86 100644 --- a/arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.c +++ b/arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.c @@ -672,12 +672,29 @@ struct op_params usb2_power_up_params[] = { {0xc200c, 0x0 /*NA*/, 0x1000000, {0x1000000}, 0, 0}, /* Phy0 register 3 - TX Channel control 0 */ {0xc400c, 0x0 /*NA*/, 0x1000000, {0x1000000}, 0, 0}, - /* check PLLCAL_DONE is set and IMPCAL_DONE is set */ + /* Decrease the amplitude of the low speed eye to meet the spec */ + {0xc000c, 0x0 /*NA*/, 0xf000, {0x1000}, 0, 0}, + {0xc200c, 0x0 /*NA*/, 0xf000, {0x1000}, 0, 0}, + {0xc400c, 0x0 /*NA*/, 0xf000, {0x1000}, 0, 0}, + /* Change the High speed impedance threshold */ + {0xc0008, 0x0 /*NA*/, 0x700, {0x600}, 0, 0}, + {0xc2008, 0x0 /*NA*/, 0x700, {0x600}, 0, 0}, + {0xc4008, 0x0 /*NA*/, 0x700, {0x600}, 0, 0}, + /* Change the squelch level of the receiver to meet the receiver electrical measurements (squelch and receiver sensitivity tests) */ + {0xc0014, 0x0 /*NA*/, 0xf, {0x8}, 0, 0}, + {0xc2014, 0x0 /*NA*/, 0xf, {0x8}, 0, 0}, + {0xc4014, 0x0 /*NA*/, 0xf, {0x8}, 0, 0}, + /* Check PLLCAL_DONE is set and IMPCAL_DONE is set */ {0xc0008, 0x0 /*NA*/, 0x80800000, {0x80800000}, 1, 1000}, - /* check REG_SQCAL_DONE is set */ + /* Check REG_SQCAL_DONE is set */ {0xc0018, 0x0 /*NA*/, 0x80000000, {0x80000000}, 1, 1000}, - /* check PLL_READY is set */ - {0xc0000, 0x0 /*NA*/, 0x80000000, {0x80000000}, 1, 1000} + /* Check PLL_READY is set */ + {0xc0000, 0x0 /*NA*/, 0x80000000, {0x80000000}, 1, 1000}, + /* Start calibrate of high seed impedance */ + {0xc0008, 0x0 /*NA*/, 0x2000, {0x2000}, 0, 0}, + {0x0, 0x0 /*NA*/, 0x0, {0x0}, 10, 0}, + /* De-assert the calibration signal */ + {0xc0008, 0x0 /*NA*/, 0x2000, {0x0}, 0, 0}, }; /*
When running USB compliance tests on our Armada-385 hardware platforms we have seen some eye mask violations. Marvell's internal documentation says: Based on silicon test results, it is recommended to change the impedance calibration threshold setting to 0x6 prior to calibration. Port changes from Marvell's u-boot fork[1] to address this. [1] - https://github.com/MarvellEmbeddedProcessors/u-boot-marvell/commit/a6221551 Signed-off-by: Chris Packham <judge.packham at gmail.com> --- .../serdes/a38x/high_speed_env_spec.c | 25 ++++++++++++++++--- 1 file changed, 21 insertions(+), 4 deletions(-)