@@ -507,11 +507,6 @@ config TARGET_PLATINUM_TITANIUM
bool "platinum-titanium"
select SUPPORT_SPL
-config TARGET_PCM058
- bool "Phytec PCM058 i.MX6 Quad"
- select BOARD_LATE_INIT
- select SUPPORT_SPL
-
config TARGET_PCL063
bool "PHYTEC PCL063 (phyCORE-i.MX6UL)"
select MX6UL
@@ -708,7 +703,6 @@ source "board/freescale/mx6sxsabreauto/Kconfig"
source "board/freescale/mx6ul_14x14_evk/Kconfig"
source "board/freescale/mx6ullevk/Kconfig"
source "board/grinn/liteboard/Kconfig"
-source "board/phytec/pcm058/Kconfig"
source "board/phytec/pcl063/Kconfig"
source "board/gateworks/gw_ventana/Kconfig"
source "board/kosagi/novena/Kconfig"
deleted file mode 100644
@@ -1,12 +0,0 @@
-if TARGET_PCM058
-
-config SYS_BOARD
- default "pcm058"
-
-config SYS_VENDOR
- default "phytec"
-
-config SYS_CONFIG_NAME
- default "pcm058"
-
-endif
deleted file mode 100644
@@ -1,6 +0,0 @@
-PHYTEC PHYBOARD MIRA
-M: Stefano Babic <sbabic at denx.de>
-S: Maintained
-F: board/phytec/pcm058/
-F: include/configs/pcm058.h
-F: configs/pcm058_defconfig
deleted file mode 100644
@@ -1,7 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2007, Guennadi Liakhovetski <lg at denx.de>
-#
-# (C) Copyright 2011 Freescale Semiconductor, Inc.
-
-obj-y := pcm058.o
deleted file mode 100644
@@ -1,35 +0,0 @@
-Board information
------------------
-
-The SBC produced by Phytec has a SOM based on a i.MX6Q.
-The SOM is sold in two versions, with eMMC or with NAND. Support
-here is for the SOM with NAND.
-The evaluation board "phyBoard-Mira" is thought to be used
-together with the SOM.
-
-More information on the board can be found on manufacturer's
-website:
-
-http://www.phytec.de/produkt/single-board-computer/phyboard-mira/
-http://www.phytec.de/fileadmin/user_upload/images/content/1.Products/SOMs/phyCORE-i.MX6/L-808e_1.pdf
-
-Building U-Boot
--------------------------------
-
-$ make pcm058_defconfig
-$ make
-
-This generates the artifacts SPL and u-boot.img.
-The SOM can boot from NAND or from SD-Card, having the SPI-NOR
-as second option.
-The dip switch "DIP-1" on the board let choose between
-NAND and SD.
-
-DIP-1 set to off: Boot first from NAND, then try SPI
-DIP-1 set to on: Boot first from SD, then try SPI
-
-The bootloader was tested with DIP-1 set to on. If a SD-card
-is present, then the RBL tries to load SPL from the SD Card, if not,
-RBL loads from SPI-NOR. The SPL tries then to load from the same
-device where SPL was loaded (SD or SPI). Booting from NAND is
-not supported.
deleted file mode 100644
@@ -1,571 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2016 Stefano Babic <sbabic at denx.de>
- */
-
-/*
- * Please note: there are two version of the board
- * one with NAND and the other with eMMC.
- * Both NAND and eMMC cannot be set because they share the
- * same pins (SD4)
- */
-#include <common.h>
-#include <init.h>
-#include <net.h>
-#include <asm/io.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/crm_regs.h>
-#include <asm/arch/mx6-ddr.h>
-#include <asm/arch/iomux.h>
-#include <asm/arch/mx6-pins.h>
-#include <asm/mach-imx/iomux-v3.h>
-#include <asm/mach-imx/boot_mode.h>
-#include <asm/mach-imx/mxc_i2c.h>
-#include <asm/mach-imx/spi.h>
-#include <linux/delay.h>
-#include <linux/errno.h>
-#include <asm/gpio.h>
-#include <mmc.h>
-#include <i2c.h>
-#include <fsl_esdhc_imx.h>
-#include <nand.h>
-#include <miiphy.h>
-#include <netdev.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/sections.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
- PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
-#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
- PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
- PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
-#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
-
-#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
-
-#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
- PAD_CTL_ODE | PAD_CTL_SRE_FAST)
-
-#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
-
-#define ASRC_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | \
- PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
-
-#define NAND_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
-
-#define ENET_PHY_RESET_GPIO IMX_GPIO_NR(1, 14)
-#define USDHC1_CD_GPIO IMX_GPIO_NR(6, 31)
-#define USER_LED IMX_GPIO_NR(1, 4)
-#define IMX6Q_DRIVE_STRENGTH 0x30
-
-int dram_init(void)
-{
- gd->ram_size = imx_ddr_size();
- return 0;
-}
-
-void board_turn_off_led(void)
-{
- gpio_direction_output(USER_LED, 0);
-}
-
-static iomux_v3_cfg_t const uart1_pads[] = {
- MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const enet_pads[] = {
- MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_SD2_DAT1__GPIO1_IO14 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const ecspi1_pads[] = {
- MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
- MX6_PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-#ifdef CONFIG_CMD_NAND
-/* NAND */
-static iomux_v3_cfg_t const nfc_pads[] = {
- MX6_PAD_NANDF_CLE__NAND_CLE | MUX_PAD_CTRL(NAND_PAD_CTRL),
- MX6_PAD_NANDF_ALE__NAND_ALE | MUX_PAD_CTRL(NAND_PAD_CTRL),
- MX6_PAD_NANDF_WP_B__NAND_WP_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
- MX6_PAD_NANDF_RB0__NAND_READY_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
- MX6_PAD_NANDF_CS0__NAND_CE0_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
- MX6_PAD_NANDF_CS1__NAND_CE1_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
- MX6_PAD_NANDF_CS2__NAND_CE2_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
- MX6_PAD_NANDF_CS3__NAND_CE3_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
- MX6_PAD_SD4_CMD__NAND_RE_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
- MX6_PAD_SD4_CLK__NAND_WE_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
- MX6_PAD_NANDF_D0__NAND_DATA00 | MUX_PAD_CTRL(NAND_PAD_CTRL),
- MX6_PAD_NANDF_D1__NAND_DATA01 | MUX_PAD_CTRL(NAND_PAD_CTRL),
- MX6_PAD_NANDF_D2__NAND_DATA02 | MUX_PAD_CTRL(NAND_PAD_CTRL),
- MX6_PAD_NANDF_D3__NAND_DATA03 | MUX_PAD_CTRL(NAND_PAD_CTRL),
- MX6_PAD_NANDF_D4__NAND_DATA04 | MUX_PAD_CTRL(NAND_PAD_CTRL),
- MX6_PAD_NANDF_D5__NAND_DATA05 | MUX_PAD_CTRL(NAND_PAD_CTRL),
- MX6_PAD_NANDF_D6__NAND_DATA06 | MUX_PAD_CTRL(NAND_PAD_CTRL),
- MX6_PAD_NANDF_D7__NAND_DATA07 | MUX_PAD_CTRL(NAND_PAD_CTRL),
- MX6_PAD_SD4_DAT0__NAND_DQS | MUX_PAD_CTRL(NAND_PAD_CTRL),
-};
-#endif
-
-static struct i2c_pads_info i2c_pad_info2 = {
- .scl = {
- .i2c_mode = MX6_PAD_GPIO_5__I2C3_SCL | I2C_PAD,
- .gpio_mode = MX6_PAD_GPIO_5__GPIO1_IO05 | I2C_PAD,
- .gp = IMX_GPIO_NR(1, 5)
- },
- .sda = {
- .i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | I2C_PAD,
- .gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | I2C_PAD,
- .gp = IMX_GPIO_NR(1, 6)
- }
-};
-
-static struct fsl_esdhc_cfg usdhc_cfg[] = {
- {.esdhc_base = USDHC1_BASE_ADDR,
- .max_bus_width = 4},
-#ifndef CONFIG_CMD_NAND
- {USDHC4_BASE_ADDR},
-#endif
-};
-
-static iomux_v3_cfg_t const usdhc1_pads[] = {
- MX6_PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD1_DAT0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD1_DAT1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD1_DAT2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD1_DAT3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_EIM_BCLK__GPIO6_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
-};
-
-#if !defined(CONFIG_CMD_NAND) && !defined(CONFIG_SPL_BUILD)
-static iomux_v3_cfg_t const usdhc4_pads[] = {
- MX6_PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-};
-#endif
-
-int board_mmc_get_env_dev(int devno)
-{
- return devno - 1;
-}
-
-int board_mmc_getcd(struct mmc *mmc)
-{
- struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
- int ret = 0;
-
- switch (cfg->esdhc_base) {
- case USDHC1_BASE_ADDR:
- ret = !gpio_get_value(USDHC1_CD_GPIO);
- break;
- case USDHC4_BASE_ADDR:
- ret = 1; /* eMMC/uSDHC4 is always present */
- break;
- }
-
- return ret;
-}
-
-int board_mmc_init(bd_t *bis)
-{
-#ifndef CONFIG_SPL_BUILD
- int ret;
- int i;
-
- for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
- switch (i) {
- case 0:
- imx_iomux_v3_setup_multiple_pads(
- usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
- gpio_direction_input(USDHC1_CD_GPIO);
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
- break;
-#ifndef CONFIG_CMD_NAND
- case 1:
- imx_iomux_v3_setup_multiple_pads(
- usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
- usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
- break;
-#endif
- default:
- printf("Warning: you configured more USDHC controllers"
- "(%d) then supported by the board (%d)\n",
- i + 1, CONFIG_SYS_FSL_USDHC_NUM);
- return -EINVAL;
- }
-
- ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
- if (ret)
- return ret;
- }
-
- return 0;
-#else
- struct src *psrc = (struct src *)SRC_BASE_ADDR;
- unsigned reg = readl(&psrc->sbmr1) >> 11;
- /*
- * Upon reading BOOT_CFG register the following map is done:
- * Bit 11 and 12 of BOOT_CFG register can determine the current
- * mmc port
- * 0x1 SD1
- * 0x2 SD2
- * 0x3 SD4
- */
-
- switch (reg & 0x3) {
- case 0x0:
- imx_iomux_v3_setup_multiple_pads(
- usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
- gpio_direction_input(USDHC1_CD_GPIO);
- usdhc_cfg[0].esdhc_base = USDHC1_BASE_ADDR;
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
- usdhc_cfg[0].max_bus_width = 4;
- gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
- break;
- }
- return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
-#endif
-}
-
-static void setup_iomux_uart(void)
-{
- imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
-}
-
-static void setup_iomux_enet(void)
-{
- imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
-
- gpio_direction_output(ENET_PHY_RESET_GPIO, 0);
- mdelay(10);
- gpio_set_value(ENET_PHY_RESET_GPIO, 1);
- mdelay(30);
-}
-
-static void setup_spi(void)
-{
- gpio_request(IMX_GPIO_NR(3, 19), "spi_cs0");
- gpio_direction_output(IMX_GPIO_NR(3, 19), 1);
-
- imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
-
- enable_spi_clk(true, 0);
-}
-
-#ifdef CONFIG_CMD_NAND
-static void setup_gpmi_nand(void)
-{
- struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
-
- /* config gpmi nand iomux */
- imx_iomux_v3_setup_multiple_pads(nfc_pads, ARRAY_SIZE(nfc_pads));
-
- /* gate ENFC_CLK_ROOT clock first,before clk source switch */
- clrbits_le32(&mxc_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
-
- /* config gpmi and bch clock to 100 MHz */
- clrsetbits_le32(&mxc_ccm->cs2cdr,
- MXC_CCM_CS2CDR_ENFC_CLK_PODF_MASK |
- MXC_CCM_CS2CDR_ENFC_CLK_PRED_MASK |
- MXC_CCM_CS2CDR_ENFC_CLK_SEL_MASK,
- MXC_CCM_CS2CDR_ENFC_CLK_PODF(0) |
- MXC_CCM_CS2CDR_ENFC_CLK_PRED(3) |
- MXC_CCM_CS2CDR_ENFC_CLK_SEL(3));
-
- /* enable ENFC_CLK_ROOT clock */
- setbits_le32(&mxc_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
-
- /* enable gpmi and bch clock gating */
- setbits_le32(&mxc_ccm->CCGR4,
- MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
- MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
- MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
- MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
- MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_OFFSET);
-
- /* enable apbh clock gating */
- setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
-}
-#endif
-
-int board_spi_cs_gpio(unsigned bus, unsigned cs)
-{
- if (bus != 0 || (cs != 0))
- return -EINVAL;
-
- return IMX_GPIO_NR(3, 19);
-}
-
-int board_eth_init(bd_t *bis)
-{
- setup_iomux_enet();
-
- return cpu_eth_init(bis);
-}
-
-int board_early_init_f(void)
-{
- setup_iomux_uart();
-
- return 0;
-}
-
-int board_init(void)
-{
- /* address of boot parameters */
- gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
-
-#ifdef CONFIG_SYS_I2C_MXC
- setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
-#endif
-
-#ifdef CONFIG_MXC_SPI
- setup_spi();
-#endif
-
-#ifdef CONFIG_CMD_NAND
- setup_gpmi_nand();
-#endif
- return 0;
-}
-
-
-#ifdef CONFIG_CMD_BMODE
-/*
- * BOOT_CFG1, BOOT_CFG2, BOOT_CFG3, BOOT_CFG4
- * see Table 8-11 and Table 5-9
- * BOOT_CFG1[7] = 1 (boot from NAND)
- * BOOT_CFG1[5] = 0 - raw NAND
- * BOOT_CFG1[4] = 0 - default pad settings
- * BOOT_CFG1[3:2] = 00 - devices = 1
- * BOOT_CFG1[1:0] = 00 - Row Address Cycles = 3
- * BOOT_CFG2[4:3] = 00 - Boot Search Count = 2
- * BOOT_CFG2[2:1] = 01 - Pages In Block = 64
- * BOOT_CFG2[0] = 0 - Reset time 12ms
- */
-static const struct boot_mode board_boot_modes[] = {
- /* NAND: 64pages per block, 3 row addr cycles, 2 copies of FCB/DBBT */
- {"nand", MAKE_CFGVAL(0x80, 0x02, 0x00, 0x00)},
- {"mmc0", MAKE_CFGVAL(0x40, 0x20, 0x00, 0x00)},
- {NULL, 0},
-};
-#endif
-
-int board_late_init(void)
-{
-#ifdef CONFIG_CMD_BMODE
- add_board_boot_modes(board_boot_modes);
-#endif
-
- return 0;
-}
-
-#ifdef CONFIG_SPL_BUILD
-#include <spl.h>
-#include <linux/libfdt.h>
-
-static const struct mx6dq_iomux_ddr_regs mx6_ddr_ioregs = {
- .dram_sdclk_0 = 0x00000030,
- .dram_sdclk_1 = 0x00000030,
- .dram_cas = 0x00000030,
- .dram_ras = 0x00000030,
- .dram_reset = 0x00000030,
- .dram_sdcke0 = 0x00000030,
- .dram_sdcke1 = 0x00000030,
- .dram_sdba2 = 0x00000000,
- .dram_sdodt0 = 0x00000030,
- .dram_sdodt1 = 0x00000030,
- .dram_sdqs0 = 0x00000030,
- .dram_sdqs1 = 0x00000030,
- .dram_sdqs2 = 0x00000030,
- .dram_sdqs3 = 0x00000030,
- .dram_sdqs4 = 0x00000030,
- .dram_sdqs5 = 0x00000030,
- .dram_sdqs6 = 0x00000030,
- .dram_sdqs7 = 0x00000030,
- .dram_dqm0 = 0x00000030,
- .dram_dqm1 = 0x00000030,
- .dram_dqm2 = 0x00000030,
- .dram_dqm3 = 0x00000030,
- .dram_dqm4 = 0x00000030,
- .dram_dqm5 = 0x00000030,
- .dram_dqm6 = 0x00000030,
- .dram_dqm7 = 0x00000030,
-};
-
-static const struct mx6dq_iomux_grp_regs mx6_grp_ioregs = {
- .grp_ddr_type = 0x000C0000,
- .grp_ddrmode_ctl = 0x00020000,
- .grp_ddrpke = 0x00000000,
- .grp_addds = IMX6Q_DRIVE_STRENGTH,
- .grp_ctlds = IMX6Q_DRIVE_STRENGTH,
- .grp_ddrmode = 0x00020000,
- .grp_b0ds = IMX6Q_DRIVE_STRENGTH,
- .grp_b1ds = IMX6Q_DRIVE_STRENGTH,
- .grp_b2ds = IMX6Q_DRIVE_STRENGTH,
- .grp_b3ds = IMX6Q_DRIVE_STRENGTH,
- .grp_b4ds = IMX6Q_DRIVE_STRENGTH,
- .grp_b5ds = IMX6Q_DRIVE_STRENGTH,
- .grp_b6ds = IMX6Q_DRIVE_STRENGTH,
- .grp_b7ds = IMX6Q_DRIVE_STRENGTH,
-};
-
-static const struct mx6_mmdc_calibration mx6_mmcd_calib = {
- .p0_mpwldectrl0 = 0x00140014,
- .p0_mpwldectrl1 = 0x000A0015,
- .p1_mpwldectrl0 = 0x000A001E,
- .p1_mpwldectrl1 = 0x000A0015,
- .p0_mpdgctrl0 = 0x43080314,
- .p0_mpdgctrl1 = 0x02680300,
- .p1_mpdgctrl0 = 0x430C0318,
- .p1_mpdgctrl1 = 0x03000254,
- .p0_mprddlctl = 0x3A323234,
- .p1_mprddlctl = 0x3E3C3242,
- .p0_mpwrdlctl = 0x2A2E3632,
- .p1_mpwrdlctl = 0x3C323E34,
-};
-
-static struct mx6_ddr3_cfg mem_ddr = {
- .mem_speed = 1600,
- .density = 2,
- .width = 16,
- .banks = 8,
- .rowaddr = 14,
- .coladdr = 10,
- .pagesz = 2,
- .trcd = 1375,
- .trcmin = 4875,
- .trasmin = 3500,
- .SRT = 1,
-};
-
-static void ccgr_init(void)
-{
- struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
-
- writel(0x00C03F3F, &ccm->CCGR0);
- writel(0x0030FC03, &ccm->CCGR1);
- writel(0x0FFFC000, &ccm->CCGR2);
- writel(0x3FF00000, &ccm->CCGR3);
- writel(0x00FFF300, &ccm->CCGR4);
- writel(0x0F0000C3, &ccm->CCGR5);
- writel(0x000003FF, &ccm->CCGR6);
-}
-
-static void spl_dram_init(void)
-{
- struct mx6_ddr_sysinfo sysinfo = {
- /* width of data bus:0=16,1=32,2=64 */
- .dsize = 2,
- /* config for full 4GB range so that get_mem_size() works */
- .cs_density = 32, /* 32Gb per CS */
- /* single chip select */
- .ncs = 1,
- .cs1_mirror = 0,
- .rtt_wr = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Wr = RZQ/4 */
- .rtt_nom = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Nom = RZQ/4 */
- .walat = 1, /* Write additional latency */
- .ralat = 5, /* Read additional latency */
- .mif3_mode = 3, /* Command prediction working mode */
- .bi_on = 1, /* Bank interleaving enabled */
- .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
- .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
- .ddr_type = DDR_TYPE_DDR3,
- .refsel = 1, /* Refresh cycles at 32KHz */
- .refr = 7, /* 8 refresh commands per refresh cycle */
- };
-
- mx6dq_dram_iocfg(64, &mx6_ddr_ioregs, &mx6_grp_ioregs);
- mx6_dram_cfg(&sysinfo, &mx6_mmcd_calib, &mem_ddr);
-}
-
-void board_boot_order(u32 *spl_boot_list)
-{
- spl_boot_list[0] = spl_boot_device();
- printf("Boot device %x\n", spl_boot_list[0]);
- switch (spl_boot_list[0]) {
- case BOOT_DEVICE_SPI:
- spl_boot_list[1] = BOOT_DEVICE_UART;
- break;
- case BOOT_DEVICE_MMC1:
- spl_boot_list[1] = BOOT_DEVICE_SPI;
- spl_boot_list[2] = BOOT_DEVICE_UART;
- break;
- default:
- printf("Boot device %x\n", spl_boot_list[0]);
- }
-}
-
-void board_init_f(ulong dummy)
-{
-#ifdef CONFIG_CMD_NAND
- /* Enable NAND */
- setup_gpmi_nand();
-#endif
-
- /* setup clock gating */
- ccgr_init();
-
- /* setup AIPS and disable watchdog */
- arch_cpu_init();
-
- /* setup AXI */
- gpr_init();
-
- board_early_init_f();
-
- /* setup GP timer */
- timer_init();
-
- setup_spi();
-
- /* UART clocks enabled and gd valid - init serial console */
- preloader_console_init();
-
- /* DDR initialization */
- spl_dram_init();
-
- /* Clear the BSS. */
- memset(__bss_start, 0, __bss_end - __bss_start);
-
- /* load/boot image from boot device */
- board_init_r(NULL, 0);
-}
-#endif
deleted file mode 100644
@@ -1,70 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_MX6=y
-CONFIG_SYS_TEXT_BASE=0x17800000
-CONFIG_SPL_GPIO_SUPPORT=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_ENV_SIZE=0x4000
-CONFIG_ENV_OFFSET=0x100000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_SYS_SPI_U_BOOT_OFFS=0x10000
-CONFIG_TARGET_PCM058=y
-CONFIG_SPL_MMC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_SPL=y
-CONFIG_ENV_OFFSET_REDUND=0x110000
-CONFIG_SPL_LIBDISK_SUPPORT=y
-CONFIG_SPL_SPI_FLASH_SUPPORT=y
-CONFIG_SPL_SPI_SUPPORT=y
-CONFIG_CMD_HDMIDETECT=y
-CONFIG_SPL_TEXT_BASE=0x00908000
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_FIT=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg,MX6Q"
-CONFIG_BOOTDELAY=3
-# CONFIG_USE_BOOTCOMMAND is not set
-CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_BOUNCE_BUFFER=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_SPL_DMA=y
-CONFIG_SPL_FS_EXT4=y
-CONFIG_SPL_I2C_SUPPORT=y
-CONFIG_SPL_SPI_LOAD=y
-CONFIG_SPL_WATCHDOG_SUPPORT=y
-CONFIG_SPL_YMODEM_SUPPORT=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND_TRIMFFS=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nand0=nand"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=nand:16m(uboot),1m(env),-(rootfs)"
-CONFIG_CMD_UBI=y
-# CONFIG_SPL_PARTITION_UUIDS is not set
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_DM=y
-CONFIG_FSL_USDHC=y
-CONFIG_MTD=y
-CONFIG_DM_MTD=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_SYS_NAND_USE_FLASH_BBT=y
-CONFIG_NAND_MXS=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=20000000
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_MICREL=y
-CONFIG_PHY_MICREL_KSZ90X1=y
-CONFIG_MII=y
-CONFIG_SPI=y
-CONFIG_MXC_SPI=y
-CONFIG_DM_THERMAL=y
-CONFIG_OF_LIBFDT=y
deleted file mode 100644
@@ -1,77 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) Stefano Babic <sbabic at denx.de>
- */
-
-
-#ifndef __PCM058_CONFIG_H
-#define __PCM058_CONFIG_H
-
-#ifdef CONFIG_SPL
-#include "imx6_spl.h"
-#endif
-
-#include "mx6_common.h"
-
-/* Thermal */
-#define CONFIG_IMX_THERMAL
-
-/* Serial */
-#define CONFIG_MXC_UART
-#define CONFIG_MXC_UART_BASE UART2_BASE
-#define CONSOLE_DEV "ttymxc1"
-
-#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024)
-
-/* Early setup */
-
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (8 * SZ_1M)
-
-/* Ethernet */
-#define CONFIG_FEC_MXC
-#define IMX_FEC_BASE ENET_BASE_ADDR
-#define CONFIG_FEC_XCV_TYPE RGMII
-#define CONFIG_ETHPRIME "FEC"
-#define CONFIG_FEC_MXC_PHYADDR 3
-
-/* SPI Flash */
-
-/* I2C Configs */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 2 */
-#define CONFIG_SYS_I2C_SPEED 100000
-
-#ifndef CONFIG_SPL_BUILD
-/* Enable NAND support */
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE 0x40000000
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-#endif
-
-/* DMA stuff, needed for GPMI/MXS NAND support */
-
-/* Filesystem support */
-
-/* Physical Memory Map */
-#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
-#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
-
-#define CONFIG_SYS_INIT_SP_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-
-/* MMC Configs */
-#define CONFIG_SYS_FSL_ESDHC_ADDR 0
-#define CONFIG_SYS_FSL_USDHC_NUM 1
-
-/* Environment organization */
-
-#endif
OF_CONTROL, DM_SPI and other driver model migration deadlines are expired for this board. Remove it. Patch-cc: Stefano Babic <sbabic at denx.de> Signed-off-by: Jagan Teki <jagan at amarulasolutions.com> --- arch/arm/mach-imx/mx6/Kconfig | 6 - board/phytec/pcm058/Kconfig | 12 - board/phytec/pcm058/MAINTAINERS | 6 - board/phytec/pcm058/Makefile | 7 - board/phytec/pcm058/README | 35 -- board/phytec/pcm058/pcm058.c | 571 -------------------------------- configs/pcm058_defconfig | 70 ---- include/configs/pcm058.h | 77 ----- 8 files changed, 784 deletions(-) delete mode 100644 board/phytec/pcm058/Kconfig delete mode 100644 board/phytec/pcm058/MAINTAINERS delete mode 100644 board/phytec/pcm058/Makefile delete mode 100644 board/phytec/pcm058/README delete mode 100644 board/phytec/pcm058/pcm058.c delete mode 100644 configs/pcm058_defconfig delete mode 100644 include/configs/pcm058.h