From patchwork Tue Jun 9 13:37:40 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: =?utf-8?q?Heiko_St=C3=BCbner?= X-Patchwork-Id: 242004 List-Id: U-Boot discussion From: heiko at sntech.de (Heiko Stuebner) Date: Tue, 9 Jun 2020 15:37:40 +0200 Subject: [PATCH 2/2] net: phy: mscc: sync rx/tx delay settings with Linux on vsc85xx In-Reply-To: <20200609133740.1421966-1-heiko@sntech.de> References: <20200609133740.1421966-1-heiko@sntech.de> Message-ID: <20200609133740.1421966-2-heiko@sntech.de> From: Heiko Stuebner The Linux kernel does set the clock delays to - 0.2 ns (their default, and lowest, hardware value) if delays should not be enabled - 2.0 ns (which causes the data to be sampled at exactly half way between clock transitions at 1000 Mbps) if delays should be enabled depending on the interface mode See https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/phy/mscc/mscc_main.c#n523 So instead of using arbitrary delay values like now, mimic this behaviour. The behaviour is the same for all of vsc8530/8531/8540/8541 so move that to a shared function while at it. Signed-off-by: Heiko Stuebner Reviewed-by: Philipp Tomsich --- drivers/net/phy/mscc.c | 70 +++++++++++++++++++++++++++--------------- 1 file changed, 46 insertions(+), 24 deletions(-) diff --git a/drivers/net/phy/mscc.c b/drivers/net/phy/mscc.c index 64e9093827..d1a643cf5a 100644 --- a/drivers/net/phy/mscc.c +++ b/drivers/net/phy/mscc.c @@ -1176,6 +1176,9 @@ static int vsc8531_vsc8541_mac_config(struct phy_device *phydev) rx_clk_out = RX_CLK_OUT_NORMAL; break; + case PHY_INTERFACE_MODE_RGMII_TXID: + case PHY_INTERFACE_MODE_RGMII_RXID: + case PHY_INTERFACE_MODE_RGMII_ID: case PHY_INTERFACE_MODE_RGMII: /* Set Reg23.12:11=2 */ mac_if = MAC_IF_SELECTION_RGMII; @@ -1259,13 +1262,43 @@ static int vsc8531_vsc8541_clkout_config(struct phy_device *phydev) return 0; } +static int vsc8531_vsc8541_clk_skew_config(struct phy_device *phydev) +{ + enum vsc_phy_rgmii_skew rx_clk_skew = VSC_PHY_RGMII_DELAY_200_PS; + enum vsc_phy_rgmii_skew tx_clk_skew = VSC_PHY_RGMII_DELAY_200_PS; + u16 reg_val; + + if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID || + phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) + rx_clk_skew = VSC_PHY_RGMII_DELAY_2000_PS; + + if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID || + phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) + tx_clk_skew = VSC_PHY_RGMII_DELAY_2000_PS; + + phy_write(phydev, MDIO_DEVAD_NONE, MSCC_EXT_PAGE_ACCESS, + MSCC_PHY_PAGE_EXT2); + reg_val = phy_read(phydev, MDIO_DEVAD_NONE, MSCC_PHY_RGMII_CNTL_REG); + + /* Reg20E2 - Update RGMII RX_Clk Skews. */ + reg_val = bitfield_replace(reg_val, RGMII_RX_CLK_DELAY_POS, + RGMII_RX_CLK_DELAY_WIDTH, rx_clk_skew); + /* Reg20E2 - Update RGMII TX_Clk Skews. */ + reg_val = bitfield_replace(reg_val, RGMII_TX_CLK_DELAY_POS, + RGMII_TX_CLK_DELAY_WIDTH, tx_clk_skew); + + phy_write(phydev, MDIO_DEVAD_NONE, MSCC_PHY_RGMII_CNTL_REG, reg_val); + phy_write(phydev, MDIO_DEVAD_NONE, MSCC_EXT_PAGE_ACCESS, + MSCC_PHY_PAGE_STD); + + return 0; +} + static int vsc8531_config(struct phy_device *phydev) { int retval = -EINVAL; u16 reg_val; u16 rmii_clk_out; - enum vsc_phy_rgmii_skew rx_clk_skew = VSC_PHY_RGMII_DELAY_1700_PS; - enum vsc_phy_rgmii_skew tx_clk_skew = VSC_PHY_RGMII_DELAY_800_PS; enum vsc_phy_clk_slew edge_rate = VSC_PHY_CLK_SLEW_RATE_4; /* For VSC8530/31 and VSC8540/41 the init scripts are the same */ @@ -1275,6 +1308,9 @@ static int vsc8531_config(struct phy_device *phydev) switch (phydev->interface) { case PHY_INTERFACE_MODE_RMII: case PHY_INTERFACE_MODE_RGMII: + case PHY_INTERFACE_MODE_RGMII_TXID: + case PHY_INTERFACE_MODE_RGMII_RXID: + case PHY_INTERFACE_MODE_RGMII_ID: retval = vsc8531_vsc8541_mac_config(phydev); if (retval != 0) return retval; @@ -1291,19 +1327,12 @@ static int vsc8531_config(struct phy_device *phydev) /* Default RMII Clk Output to 0=OFF/1=ON */ rmii_clk_out = 0; + retval = vsc8531_vsc8541_clk_skew_config(phydev); + if (retval != 0) + return retval; + phy_write(phydev, MDIO_DEVAD_NONE, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_EXT2); - reg_val = phy_read(phydev, MDIO_DEVAD_NONE, MSCC_PHY_RGMII_CNTL_REG); - - /* Reg20E2 - Update RGMII RX_Clk Skews. */ - reg_val = bitfield_replace(reg_val, RGMII_RX_CLK_DELAY_POS, - RGMII_RX_CLK_DELAY_WIDTH, rx_clk_skew); - /* Reg20E2 - Update RGMII TX_Clk Skews. */ - reg_val = bitfield_replace(reg_val, RGMII_TX_CLK_DELAY_POS, - RGMII_TX_CLK_DELAY_WIDTH, tx_clk_skew); - - phy_write(phydev, MDIO_DEVAD_NONE, MSCC_PHY_RGMII_CNTL_REG, reg_val); - reg_val = phy_read(phydev, MDIO_DEVAD_NONE, MSCC_PHY_WOL_MAC_CONTROL); /* Reg27E2 - Update Clk Slew Rate. */ reg_val = bitfield_replace(reg_val, EDGE_RATE_CNTL_POS, @@ -1329,8 +1358,6 @@ static int vsc8541_config(struct phy_device *phydev) int retval = -EINVAL; u16 reg_val; u16 rmii_clk_out; - enum vsc_phy_rgmii_skew rx_clk_skew = VSC_PHY_RGMII_DELAY_1700_PS; - enum vsc_phy_rgmii_skew tx_clk_skew = VSC_PHY_RGMII_DELAY_800_PS; enum vsc_phy_clk_slew edge_rate = VSC_PHY_CLK_SLEW_RATE_4; /* For VSC8530/31 and VSC8540/41 the init scripts are the same */ @@ -1358,17 +1385,12 @@ static int vsc8541_config(struct phy_device *phydev) /* Default RMII Clk Output to 0=OFF/1=ON */ rmii_clk_out = 0; + retval = vsc8531_vsc8541_clk_skew_config(phydev); + if (retval != 0) + return retval; + phy_write(phydev, MDIO_DEVAD_NONE, MSCC_EXT_PAGE_ACCESS, MSCC_PHY_PAGE_EXT2); - reg_val = phy_read(phydev, MDIO_DEVAD_NONE, MSCC_PHY_RGMII_CNTL_REG); - /* Reg20E2 - Update RGMII RX_Clk Skews. */ - reg_val = bitfield_replace(reg_val, RGMII_RX_CLK_DELAY_POS, - RGMII_RX_CLK_DELAY_WIDTH, rx_clk_skew); - /* Reg20E2 - Update RGMII TX_Clk Skews. */ - reg_val = bitfield_replace(reg_val, RGMII_TX_CLK_DELAY_POS, - RGMII_TX_CLK_DELAY_WIDTH, tx_clk_skew); - phy_write(phydev, MDIO_DEVAD_NONE, MSCC_PHY_RGMII_CNTL_REG, reg_val); - reg_val = phy_read(phydev, MDIO_DEVAD_NONE, MSCC_PHY_WOL_MAC_CONTROL); /* Reg27E2 - Update Clk Slew Rate. */ reg_val = bitfield_replace(reg_val, EDGE_RATE_CNTL_POS,