From patchwork Fri Jun 5 12:44:40 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Pratyush Yadav X-Patchwork-Id: 241811 List-Id: U-Boot discussion From: p.yadav at ti.com (Pratyush Yadav) Date: Fri, 5 Jun 2020 18:14:40 +0530 Subject: [PATCH v6 01/21] spi: spi-mem: allow specifying whether an op is DTR or not In-Reply-To: <20200605124500.17867-1-p.yadav@ti.com> References: <20200605124500.17867-1-p.yadav@ti.com> Message-ID: <20200605124500.17867-2-p.yadav@ti.com> Each phase is given a separate 'dtr' field so mixed protocols like 4S-4D-4D can be supported. Signed-off-by: Pratyush Yadav --- drivers/spi/spi-mem.c | 3 +++ include/spi-mem.h | 8 ++++++++ 2 files changed, 11 insertions(+) diff --git a/drivers/spi/spi-mem.c b/drivers/spi/spi-mem.c index d344701aeb..967c241853 100644 --- a/drivers/spi/spi-mem.c +++ b/drivers/spi/spi-mem.c @@ -159,6 +159,9 @@ bool spi_mem_default_supports_op(struct spi_slave *slave, op->data.dir == SPI_MEM_DATA_OUT)) return false; + if (op->cmd.dtr || op->addr.dtr || op->dummy.dtr || op->data.dtr) + return false; + return true; } EXPORT_SYMBOL_GPL(spi_mem_default_supports_op); diff --git a/include/spi-mem.h b/include/spi-mem.h index 893f7bd733..55e5019a1c 100644 --- a/include/spi-mem.h +++ b/include/spi-mem.h @@ -74,6 +74,7 @@ enum spi_mem_data_dir { * struct spi_mem_op - describes a SPI memory operation * @cmd.buswidth: number of IO lines used to transmit the command * @cmd.opcode: operation opcode + * @cmd.dtr: whether the command opcode should be sent in DTR mode or not * @addr.nbytes: number of address bytes to send. Can be zero if the operation * does not need to send an address * @addr.buswidth: number of IO lines used to transmit the address cycles @@ -81,10 +82,13 @@ enum spi_mem_data_dir { * Note that only @addr.nbytes are taken into account in this * address value, so users should make sure the value fits in the * assigned number of bytes. + * @addr.dtr: whether the address should be sent in DTR mode or not * @dummy.nbytes: number of dummy bytes to send after an opcode or address. Can * be zero if the operation does not require dummy bytes * @dummy.buswidth: number of IO lanes used to transmit the dummy bytes + * @dummy.dtr: whether the dummy bytes should be sent in DTR mode or not * @data.buswidth: number of IO lanes used to send/receive the data + * @data.dtr: whether the data should be sent in DTR mode or not * @data.dir: direction of the transfer * @data.buf.in: input buffer * @data.buf.out: output buffer @@ -93,21 +97,25 @@ struct spi_mem_op { struct { u8 buswidth; u8 opcode; + u8 dtr : 1; } cmd; struct { u8 nbytes; u8 buswidth; + u8 dtr : 1; u64 val; } addr; struct { u8 nbytes; u8 buswidth; + u8 dtr : 1; } dummy; struct { u8 buswidth; + u8 dtr : 1; enum spi_mem_data_dir dir; unsigned int nbytes; /* buf.{in,out} must be DMA-able. */