@@ -120,7 +120,6 @@ config SYS_IVM_EEPROM_PAGE_LEN
Page size of inventory in EEPROM.
source "board/keymile/km83xx/Kconfig"
-source "board/keymile/kmp204x/Kconfig"
source "board/keymile/km_arm/Kconfig"
endmenu
deleted file mode 100644
@@ -1,20 +0,0 @@
-if TARGET_KMP204X
-
-config SYS_BOARD
- default "kmp204x"
-
-config SYS_VENDOR
- default "keymile"
-
-config SYS_CONFIG_NAME
- default "kmp204x"
-
-config BOARD_SPECIFIC_OPTIONS # dummy
- def_bool y
- select ARCH_P2041
- select FSL_DDR_INTERACTIVE
- select PHYS_64BIT
- imply CMD_CRAMFS
- imply FS_CRAMFS
-
-endif
deleted file mode 100644
@@ -1,6 +0,0 @@
-KMP204X BOARD
-M: Valentin Longchamp <valentin.longchamp at ch.abb.com>
-S: Maintained
-F: board/keymile/kmp204x/
-F: include/configs/kmp204x.h
-F: configs/kmcoge4_defconfig
deleted file mode 100644
@@ -1,10 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2001-2007
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-
-obj-y := kmp204x.o ddr.o eth.o tlb.o pci.o law.o ../common/common.o\
- ../common/ivm.o ../common/qrio.o
deleted file mode 100644
@@ -1,69 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2013 Keymile AG
- * Valentin Longchamp <valentin.longchamp at keymile.com>
- *
- * Copyright 2009-2011 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <i2c.h>
-#include <hwconfig.h>
-#include <init.h>
-#include <log.h>
-#include <asm/mmu.h>
-#include <fsl_ddr_sdram.h>
-#include <fsl_ddr_dimm_params.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-void fsl_ddr_board_options(memctl_options_t *popts,
- dimm_params_t *pdimm,
- unsigned int ctrl_num)
-{
- if (ctrl_num) {
- printf("Wrong parameter for controller number %d", ctrl_num);
- return;
- }
-
- /* automatic calibration for nb of cycles between read and DQS pre */
- popts->cpo_override = 0xFF;
-
- /* 1/2 clk delay between wr command and data strobe */
- popts->write_data_delay = 4;
- /* clk lauched 1/2 applied cylcle after address command */
- popts->clk_adjust = 4;
- /* 1T timing: command/address held for only 1 cycle */
- popts->twot_en = 0;
-
- /* we have only one module, half str should be OK */
- popts->half_strength_driver_enable = 1;
-
- /* wrlvl values overridden as recommended by ddr init func */
- popts->wrlvl_override = 1;
- popts->wrlvl_sample = 0xf;
- popts->wrlvl_start = 0x6;
-
- /* Enable ZQ calibration */
- popts->zq_en = 1;
-
- /* DHC_EN =1, ODT = 75 Ohm */
- popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR_ODT_75ohm;
-}
-
-int dram_init(void)
-{
- phys_size_t dram_size = 0;
-
- puts("Initializing with SPD\n");
-
- dram_size = fsl_ddr_sdram();
-
- dram_size = setup_ddr_tlbs(dram_size / 0x100000);
- dram_size *= 0x100000;
-
- debug(" DDR: ");
- gd->ram_size = dram_size;
-
- return 0;
-}
deleted file mode 100644
@@ -1,71 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2013 Keymile AG
- * Valentin Longchamp <valentin.longchamp at keymile.com>
- */
-
-#include <common.h>
-#include <net.h>
-#include <netdev.h>
-#include <fm_eth.h>
-#include <fsl_mdio.h>
-#include <phy.h>
-
-int board_eth_init(bd_t *bis)
-{
- int ret = 0;
-#ifdef CONFIG_FMAN_ENET
- struct fsl_pq_mdio_info dtsec_mdio_info;
-
- printf("Initializing Fman\n");
-
- dtsec_mdio_info.regs =
- (struct tsec_mii_mng *)CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR;
- dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
-
- /* Register the real 1G MDIO bus */
- fsl_pq_mdio_init(bis, &dtsec_mdio_info);
-
- /* DTESC1/2 don't have a PHY, they are temporarily disabled
- * so that u-boot doesn't try to unsuccessfuly enable them */
- fm_disable_port(FM1_DTSEC1);
- fm_disable_port(FM1_DTSEC2);
-
- /*
- * Program RGMII DTSEC5 (FM1 MAC5) on the EC2 physical itf
- * This is the debug interface, the only one used in u-boot
- */
- fm_info_set_phy_address(FM1_DTSEC5, CONFIG_SYS_FM1_DTSEC5_PHY_ADDR);
- fm_info_set_mdio(FM1_DTSEC5,
- miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME));
-
- ret = cpu_eth_init(bis);
-
- /* reenable DTSEC1/2 for later (kernel) */
- fm_enable_port(FM1_DTSEC1);
- fm_enable_port(FM1_DTSEC2);
-#endif
-
- return ret;
-}
-
-#if defined(CONFIG_PHYLIB) && defined(CONFIG_PHY_MARVELL)
-
-#define mv88E1118_PAGE_REG 22
-
-int board_phy_config(struct phy_device *phydev)
-{
- if (phydev->addr == CONFIG_SYS_FM1_DTSEC5_PHY_ADDR) {
- /* driver config is good */
- if (phydev->drv->config)
- phydev->drv->config(phydev);
-
- /* but we still need to fix the LEDs */
- phy_write(phydev, MDIO_DEVAD_NONE, mv88E1118_PAGE_REG, 0x0003);
- phy_write(phydev, MDIO_DEVAD_NONE, 0x10, 0x0840);
- phy_write(phydev, MDIO_DEVAD_NONE, mv88E1118_PAGE_REG, 0x0000);
- }
-
- return 0;
-}
-#endif
deleted file mode 100644
@@ -1,265 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2013 Keymile AG
- * Valentin Longchamp <valentin.longchamp at keymile.com>
- *
- * Copyright 2011,2012 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <command.h>
-#include <env.h>
-#include <fdt_support.h>
-#include <image.h>
-#include <init.h>
-#include <netdev.h>
-#include <linux/compiler.h>
-#include <asm/mmu.h>
-#include <asm/processor.h>
-#include <asm/cache.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_law.h>
-#include <asm/fsl_serdes.h>
-#include <asm/fsl_portals.h>
-#include <asm/fsl_liodn.h>
-#include <fm_eth.h>
-
-#include "../common/common.h"
-#include "../common/qrio.h"
-#include "kmp204x.h"
-
-static uchar ivm_content[CONFIG_SYS_IVM_EEPROM_MAX_LEN];
-
-int checkboard(void)
-{
- printf("Board: Keymile %s\n", CONFIG_SYS_CONFIG_NAME);
-
- return 0;
-}
-
-#define ZL30158_RST 8
-#define BFTIC4_RST 0
-#define RSTRQSR1_WDT_RR 0x00200000
-#define RSTRQSR1_SW_RR 0x00100000
-
-int board_early_init_f(void)
-{
- ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- bool cpuwd_flag = false;
-
- /* configure mode for uP reset request */
- qrio_uprstreq(UPREQ_CORE_RST);
-
- /* board only uses the DDR_MCK0, so disable the DDR_MCK1/2/3 */
- setbits_be32(&gur->ddrclkdr, 0x001f000f);
-
- /* set reset reason according CPU register */
- if ((gur->rstrqsr1 & (RSTRQSR1_WDT_RR | RSTRQSR1_SW_RR)) ==
- RSTRQSR1_WDT_RR)
- cpuwd_flag = true;
-
- qrio_cpuwd_flag(cpuwd_flag);
- /* clear CPU bits by writing 1 */
- setbits_be32(&gur->rstrqsr1, RSTRQSR1_WDT_RR | RSTRQSR1_SW_RR);
-
- /* set the BFTIC's prstcfg to reset at power-up and unit reset only */
- qrio_prstcfg(BFTIC4_RST, PRSTCFG_POWUP_UNIT_RST);
- /* and enable WD on it */
- qrio_wdmask(BFTIC4_RST, true);
-
- /* set the ZL30138's prstcfg to reset at power-up only */
- qrio_prstcfg(ZL30158_RST, PRSTCFG_POWUP_RST);
- /* and take it out of reset as soon as possible (needed for Hooper) */
- qrio_prst(ZL30158_RST, false, false);
-
- return 0;
-}
-
-int board_early_init_r(void)
-{
- int ret = 0;
- /* Flush d-cache and invalidate i-cache of any FLASH data */
- flush_dcache();
- invalidate_icache();
-
- set_liodns();
- setup_qbman_portals();
-
- ret = trigger_fpga_config();
- if (ret)
- printf("error triggering PCIe FPGA config\n");
-
- /* enable the Unit LED (red) & Boot LED (on) */
- qrio_set_leds();
-
- /* enable Application Buffer */
- qrio_enable_app_buffer();
-
- return 0;
-}
-
-unsigned long get_board_sys_clk(unsigned long dummy)
-{
- return 66666666;
-}
-
-#define ETH_FRONT_PHY_RST 15
-#define QSFP2_RST 11
-#define QSFP1_RST 10
-#define ZL30343_RST 9
-
-int misc_init_f(void)
-{
- /* configure QRIO pis for i2c deblocking */
- i2c_deblock_gpio_cfg();
-
- /* configure the front phy's prstcfg and take it out of reset */
- qrio_prstcfg(ETH_FRONT_PHY_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
- qrio_prst(ETH_FRONT_PHY_RST, false, false);
-
- /* set the ZL30343 prstcfg to reset at power-up only */
- qrio_prstcfg(ZL30343_RST, PRSTCFG_POWUP_RST);
- /* and enable the WD on it */
- qrio_wdmask(ZL30343_RST, true);
-
- /* set the QSFPs' prstcfg to reset at power-up and unit rst only */
- qrio_prstcfg(QSFP1_RST, PRSTCFG_POWUP_UNIT_RST);
- qrio_prstcfg(QSFP2_RST, PRSTCFG_POWUP_UNIT_RST);
-
- /* and enable the WD on them */
- qrio_wdmask(QSFP1_RST, true);
- qrio_wdmask(QSFP2_RST, true);
-
- return 0;
-}
-
-#define NUM_SRDS_BANKS 2
-
-int misc_init_r(void)
-{
- serdes_corenet_t *regs = (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR;
- u32 expected[NUM_SRDS_BANKS] = {SRDS_PLLCR0_RFCK_SEL_100,
- SRDS_PLLCR0_RFCK_SEL_125};
- unsigned int i;
-
- /* check SERDES reference clocks */
- for (i = 0; i < NUM_SRDS_BANKS; i++) {
- u32 actual = in_be32(®s->bank[i].pllcr0);
- actual &= SRDS_PLLCR0_RFCK_SEL_MASK;
- if (actual != expected[i]) {
- printf("Warning: SERDES bank %u expects reference \
- clock %sMHz, but actual is %sMHz\n", i + 1,
- serdes_clock_to_string(expected[i]),
- serdes_clock_to_string(actual));
- }
- }
-
- ivm_read_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN,
- CONFIG_PIGGY_MAC_ADDRESS_OFFSET);
- return 0;
-}
-
-#if defined(CONFIG_HUSH_INIT_VAR)
-int hush_init_var(void)
-{
- ivm_analyze_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN);
- return 0;
-}
-#endif
-
-#if defined(CONFIG_LAST_STAGE_INIT)
-
-int last_stage_init(void)
-{
-#if defined(CONFIG_KMCOGE4)
- /* on KMCOGE4, the BFTIC4 is on the LBAPP2 */
- struct bfticu_iomap *bftic4 =
- (struct bfticu_iomap *)CONFIG_SYS_LBAPP2_BASE;
- u8 dip_switch = in_8((u8 *)&(bftic4->mswitch)) & BFTICU_DIPSWITCH_MASK;
-
- if (dip_switch != 0) {
- /* start bootloader */
- puts("DIP: Enabled\n");
- env_set("actual_bank", "0");
- }
-#endif
- set_km_env();
-
- return 0;
-}
-#endif
-
-#ifdef CONFIG_SYS_DPAA_FMAN
-void fdt_fixup_fman_mac_addresses(void *blob)
-{
- int node, i, ret;
- char *tmp, *end;
- unsigned char mac_addr[6];
-
- /* get the mac addr from env */
- tmp = env_get("ethaddr");
- if (!tmp) {
- printf("ethaddr env variable not defined\n");
- return;
- }
- for (i = 0; i < 6; i++) {
- mac_addr[i] = tmp ? simple_strtoul(tmp, &end, 16) : 0;
- if (tmp)
- tmp = (*end) ? end+1 : end;
- }
-
- /* find the correct fdt ethernet path and correct it */
- node = fdt_path_offset(blob, "/soc/fman/ethernet at e8000");
- if (node < 0) {
- printf("no /soc/fman/ethernet path offset\n");
- return;
- }
- ret = fdt_setprop(blob, node, "local-mac-address", &mac_addr, 6);
- if (ret) {
- printf("error setting local-mac-address property\n");
- return;
- }
-}
-#endif
-
-int ft_board_setup(void *blob, bd_t *bd)
-{
- phys_addr_t base;
- phys_size_t size;
-
- ft_cpu_setup(blob, bd);
-
- base = env_get_bootm_low();
- size = env_get_bootm_size();
-
- fdt_fixup_memory(blob, (u64)base, (u64)size);
-
-#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB)
- fsl_fdt_fixup_dr_usb(blob, bd);
-#endif
-
-#ifdef CONFIG_PCI
- pci_of_setup(blob, bd);
-#endif
-
- fdt_fixup_liodn(blob);
-#ifdef CONFIG_SYS_DPAA_FMAN
- fdt_fixup_fman_ethernet(blob);
- fdt_fixup_fman_mac_addresses(blob);
-#endif
-
- return 0;
-}
-
-#if defined(CONFIG_POST)
-
-/* DIC26_SELFTEST GPIO used to start factory test sw */
-#define SELFTEST_PORT QRIO_GPIO_A
-#define SELFTEST_PIN 31
-
-int post_hotkeys_pressed(void)
-{
- qrio_gpio_direction_input(SELFTEST_PORT, SELFTEST_PIN);
- return qrio_get_gpio(SELFTEST_PORT, SELFTEST_PIN);
-}
-#endif
deleted file mode 100644
@@ -1,8 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2013 Keymile AG
- * Valentin Longchamp <valentin.longchamp at keymile.com>
- */
-
-
-void pci_of_setup(void *blob, bd_t *bd);
deleted file mode 100644
@@ -1,39 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2013 Keymile AG
- * Valentin Longchamp <valentin.longchamp at keymile.com>
- *
- * Copyright 2008-2011 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- */
-
-#include <common.h>
-#include <asm/fsl_law.h>
-#include <asm/mmu.h>
-
-struct law_entry law_table[] = {
-#ifdef CONFIG_SYS_BMAN_MEM_PHYS
- SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_2M, LAW_TRGT_IF_BMAN),
-#endif
-#ifdef CONFIG_SYS_QMAN_MEM_PHYS
- SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_2M, LAW_TRGT_IF_QMAN),
-#endif
-#ifdef CONFIG_SYS_DCSRBAR_PHYS
- /* Limit DCSR to 32M to access NPC Trace Buffer */
- SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR),
-#endif
-#ifdef CONFIG_SYS_NAND_BASE_PHYS
- SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_32K, LAW_TRGT_IF_LBC),
-#endif
- SET_LAW(CONFIG_SYS_QRIO_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_LBC),
-#ifdef CONFIG_SYS_LBAPP1_BASE_PHYS
- SET_LAW(CONFIG_SYS_LBAPP1_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
-#endif
-#ifdef CONFIG_SYS_LBAPP2_BASE_PHYS
- SET_LAW(CONFIG_SYS_LBAPP2_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
-#endif
-};
-
-int num_law_entries = ARRAY_SIZE(law_table);
deleted file mode 100644
@@ -1,74 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright 2012 Freescale Semiconductor, Inc.
-# Refer docs/README.pblimage for more details about how-to configure
-# and create PBL boot image
-#
-
-#PBI commands
-#Configure ALTCBAR for DCSR -> DCSR at 89000000
-091380c0 000009C4
-09000010 00000000
-091380c0 000009C4
-09000014 00000000
-091380c0 000009C4
-09000018 81d00000
-#Workaround for A-004849
-091380c0 000009C4
-890B0050 00000002
-091380c0 000009C4
-890B0054 00000002
-091380c0 000009C4
-890B0058 00000002
-091380c0 000009C4
-890B005C 00000002
-091380c0 000009C4
-890B0090 00000002
-091380c0 000009C4
-890B0094 00000002
-091380c0 000009C4
-890B0098 00000002
-091380c0 000009C4
-890B009C 00000002
-091380c0 000009C4
-890B0108 00000012
-091380c0 000009C4
-#Workaround for A-006559 needed for rev 2.0 of P2041 silicon
-89021008 0000f000
-091380c0 000009C4
-89021028 0000f000
-091380c0 000009C4
-89021048 0000f000
-091380c0 000009C4
-89021068 0000f000
-091380c0 000009C4
-#Flush PBL data
-09138000 00000000
-#Disable ALTCBAR
-09000018 00000000
-091380c0 000009C4
-#Initialize CPC1 as 1MB SRAM
-09010000 00200400
-09138000 00000000
-091380c0 00000100
-09010100 00000000
-09010104 fff0000b
-09010f00 08000000
-09010000 80000000
-#Configure LAW for CPC1
-09000d00 00000000
-09000d04 fff00000
-09000d08 81000013
-09000010 00000000
-09000014 ff000000
-09000018 81000000
-#Initialize eSPI controller, default configuration is slow for eSPI to
-#load data, this configuration comes from u-boot eSPI driver.
-09110000 80000403
-09110020 27170008
-09110024 00100008
-09110028 00100008
-0911002c 00100008
-#Flush PBL data
-09138000 00000000
-091380c0 00000000
deleted file mode 100644
@@ -1,125 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2013 Keymile AG
- * Valentin Longchamp <valentin.longchamp at keymile.com>
- *
- * Copyright 2007-2011 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <command.h>
-#include <init.h>
-#include <pci.h>
-#include <asm/fsl_pci.h>
-#include <linux/delay.h>
-#include <linux/libfdt.h>
-#include <fdt_support.h>
-#include <asm/fsl_serdes.h>
-#include <linux/errno.h>
-
-#include "../common/qrio.h"
-#include "kmp204x.h"
-
-#define PROM_SEL_L 11
-/* control the PROM_SEL_L signal*/
-static void toggle_fpga_eeprom_bus(bool cpu_own)
-{
- qrio_gpio_direction_output(QRIO_GPIO_A, PROM_SEL_L, !cpu_own);
-}
-
-#define CONF_SEL_L 10
-#define FPGA_PROG_L 19
-#define FPGA_DONE 18
-#define FPGA_INIT_L 17
-
-int trigger_fpga_config(void)
-{
- int ret = 0, init_l;
- /* approx 10ms */
- u32 timeout = 10000;
-
- /* make sure the FPGA_can access the EEPROM */
- toggle_fpga_eeprom_bus(false);
-
- /* assert CONF_SEL_L to be able to drive FPGA_PROG_L */
- qrio_gpio_direction_output(QRIO_GPIO_A, CONF_SEL_L, 0);
-
- /* trigger the config start */
- qrio_gpio_direction_output(QRIO_GPIO_A, FPGA_PROG_L, 0);
-
- /* small delay for INIT_L line */
- udelay(10);
-
- /* wait for FPGA_INIT to be asserted */
- do {
- init_l = qrio_get_gpio(QRIO_GPIO_A, FPGA_INIT_L);
- if (timeout-- == 0) {
- printf("FPGA_INIT timeout\n");
- ret = -EFAULT;
- break;
- }
- udelay(10);
- } while (init_l);
-
- /* deassert FPGA_PROG, config should start */
- qrio_set_gpio(QRIO_GPIO_A, FPGA_PROG_L, 1);
-
- return ret;
-}
-
-/* poll the FPGA_DONE signal and give the EEPROM back to the QorIQ */
-static int wait_for_fpga_config(void)
-{
- int ret = 0, done;
- /* approx 5 s */
- u32 timeout = 500000;
-
- printf("PCIe FPGA config:");
- do {
- done = qrio_get_gpio(QRIO_GPIO_A, FPGA_DONE);
- if (timeout-- == 0) {
- printf(" FPGA_DONE timeout\n");
- ret = -EFAULT;
- goto err_out;
- }
- udelay(10);
- } while (!done);
-
- printf(" done\n");
-
-err_out:
- /* deactive CONF_SEL and give the CPU conf EEPROM access */
- qrio_set_gpio(QRIO_GPIO_A, CONF_SEL_L, 1);
- toggle_fpga_eeprom_bus(true);
-
- return ret;
-}
-
-#define PCIE_SW_RST 14
-#define PEXHC_RST 13
-#define HOOPER_RST 12
-
-void pci_init_board(void)
-{
- qrio_prstcfg(PCIE_SW_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
- qrio_prstcfg(PEXHC_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
- qrio_prstcfg(HOOPER_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
-
- /* wait for the PCIe FPGA to be configured
- * it has been triggered earlier in board_early_init_r */
- if (wait_for_fpga_config())
- printf("error finishing PCIe FPGA config\n");
-
- qrio_prst(PCIE_SW_RST, false, false);
- qrio_prst(PEXHC_RST, false, false);
- qrio_prst(HOOPER_RST, false, false);
- /* Hooper is not direcly PCIe capable */
- mdelay(50);
-
- fsl_pcie_init_board(0);
-}
-
-void pci_of_setup(void *blob, bd_t *bd)
-{
- FT_FSL_PCI_SETUP;
-}
deleted file mode 100644
@@ -1,11 +0,0 @@
-#
-# Default RCW for kmp204x boards
-#
-
-#PBL preamble and RCW header
-aa55aa55 010e0100
-#64 bytes RCW data
-14600000 00000000 28200000 00000000
-148E70CF CFC02000 58000000 41000000
-00000000 00000000 00000000 F0428816
-00000000 00000000 00000000 00000000
deleted file mode 100644
@@ -1,109 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2013 Keymile AG
- * Valentin Longchamp <valentin.longchamp at keymile.com>
- *
- * Copyright 2008-2011 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- */
-
-#include <common.h>
-#include <asm/mmu.h>
-
-struct fsl_e_tlb_entry tlb_table[] = {
- /* TLB 0 - for temp stack in cache */
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS,
- MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
- MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
- MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
- CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
- MAS3_SW|MAS3_SR, 0,
- 0, 0, BOOKE_PAGESZ_4K, 0),
- /* TLB 1 */
- /* *I*G - L3SRAM. When L3 is used as 1M SRAM, the address of the
- * SRAM is at 0xfff00000, it covered the 0xfffff000.
- */
- SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
- MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 0, BOOKE_PAGESZ_1M, 1),
-
- /* *I*G* - CCSRBAR */
- SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
- MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 1, BOOKE_PAGESZ_16M, 1),
- /* QRIO */
- SET_TLB_ENTRY(1, CONFIG_SYS_QRIO_BASE, CONFIG_SYS_QRIO_BASE_PHYS,
- MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 2, BOOKE_PAGESZ_64K, 1),
- /* *I*G* - PCI1 */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
- MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 3, BOOKE_PAGESZ_512M, 1),
- /* *I*G* - PCI3 */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, CONFIG_SYS_PCIE3_MEM_PHYS,
- MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 4, BOOKE_PAGESZ_512M, 1),
- /* *I*G* - PCI1&3 I/O */
- SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
- MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 6, BOOKE_PAGESZ_128K, 1),
-#ifdef CONFIG_SYS_LBAPP1_BASE_PHYS
- /* LBAPP1 */
- SET_TLB_ENTRY(1, CONFIG_SYS_LBAPP1_BASE, CONFIG_SYS_LBAPP1_BASE_PHYS,
- MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 7, BOOKE_PAGESZ_256M, 1),
-#endif
-#ifdef CONFIG_SYS_LBAPP2_BASE_PHYS
- /* LBAPP2 */
- SET_TLB_ENTRY(1, CONFIG_SYS_LBAPP2_BASE, CONFIG_SYS_LBAPP2_BASE_PHYS,
- MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 8, BOOKE_PAGESZ_256M, 1),
-#endif
- /* Bman/Qman */
-#ifdef CONFIG_SYS_BMAN_MEM_PHYS
- SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
- MAS3_SW|MAS3_SR, 0,
- 0, 9, BOOKE_PAGESZ_1M, 1),
- SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x00100000,
- CONFIG_SYS_BMAN_MEM_PHYS + 0x00100000,
- MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 10, BOOKE_PAGESZ_1M, 1),
-#endif
-#ifdef CONFIG_SYS_QMAN_MEM_PHYS
- SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
- MAS3_SW|MAS3_SR, 0,
- 0, 11, BOOKE_PAGESZ_1M, 1),
- SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x00100000,
- CONFIG_SYS_QMAN_MEM_PHYS + 0x00100000,
- MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 12, BOOKE_PAGESZ_1M, 1),
-#endif
-#ifdef CONFIG_SYS_DCSRBAR_PHYS
- SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
- MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 13, BOOKE_PAGESZ_4M, 1),
-#endif
-#ifdef CONFIG_SYS_NAND_BASE
- /*
- * *I*G - NAND
- * entry 14 and 15 has been used hard coded, they will be disabled
- * in cpu_init_f, so we use entry 16 for nand.
- */
- SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
- MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
- 0, 16, BOOKE_PAGESZ_32K, 1),
-#endif
-};
-
-int num_tlb_entries = ARRAY_SIZE(tlb_table);
deleted file mode 100644
@@ -1,68 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xfff40000
-CONFIG_ENV_SIZE=0x4000
-CONFIG_ENV_OFFSET=0x100000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_BOOTCOUNT_BOOTLIMIT=3
-CONFIG_SYS_BOOTCOUNT_ADDR=0xFB000020
-CONFIG_ENV_OFFSET_REDUND=0x110000
-CONFIG_MPC85xx=y
-CONFIG_TARGET_KMP204X=y
-# CONFIG_SYS_MALLOC_F is not set
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="KMCOGE4"
-CONFIG_VERSION_VARIABLE=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_BOARD_EARLY_INIT_R=y
-CONFIG_LAST_STAGE_INIT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_AUTOBOOT_KEYED=y
-CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n"
-CONFIG_AUTOBOOT_STOP_STR=" "
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_EEPROM=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_I2C=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_MP=y
-# CONFIG_CMD_HASH is not set
-CONFIG_CMD_JFFS2=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nand0=fsl_elbc_nand"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=fsl_elbc_nand:-(ubi0);"
-# CONFIG_CMD_IRQ is not set
-CONFIG_CMD_UBI=y
-# CONFIG_CMD_UBIFS is not set
-CONFIG_DOS_PARTITION=y
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_DM=y
-CONFIG_BOOTCOUNT_LIMIT=y
-# CONFIG_MMC is not set
-CONFIG_MTD=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=20000000
-CONFIG_SPI_FLASH_SPANSION=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_PHYLIB=y
-CONFIG_PHYLIB_10G=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_GIGE=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_BCH=y
-CONFIG_OF_LIBFDT=y
deleted file mode 100644
@@ -1,435 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2013 Keymile AG
- * Valentin Longchamp <valentin.longchamp at keymile.com>
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#if defined(CONFIG_KMCOGE4)
-#define CONFIG_HOSTNAME "kmcoge4"
-
-#else
-#error ("Board not supported")
-#endif
-
-#define CONFIG_KMP204X
-
-/* an additionnal option is required for UBI as subpage access is
- * supported in u-boot
- */
-#define CONFIG_KM_UBI_PART_BOOT_OPTS ",2048"
-
-#define CONFIG_NAND_ECC_BCH
-
-/* common KM defines */
-#include "km/keymile-common.h"
-
-#define CONFIG_SYS_RAMBOOT
-#define CONFIG_RAMBOOT_PBL
-#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
-#define CONFIG_SYS_FSL_PBL_PBI board/keymile/kmp204x/pbi.cfg
-#define CONFIG_SYS_FSL_PBL_RCW board/keymile/kmp204x/rcw_kmp204x.cfg
-
-/* High Level Configuration Options */
-#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
-#define CONFIG_FSL_CORENET /* Freescale CoreNet platform */
-
-#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
-#define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS
-#define CONFIG_PCIE1 /* PCIE controller 1 */
-#define CONFIG_PCIE3 /* PCIE controller 3 */
-#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
-#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
-
-#define CONFIG_SYS_DPAA_RMAN /* RMan */
-
-/* Environment in SPI Flash */
-#define CONFIG_ENV_TOTAL_SIZE 0x020000
-
-#ifndef __ASSEMBLY__
-unsigned long get_board_sys_clk(unsigned long dummy);
-#endif
-#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_SYS_CACHE_STASHING
-#define CONFIG_BACKSIDE_L2_CACHE
-#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E
-#define CONFIG_BTB /* toggle branch predition */
-
-#define CONFIG_ENABLE_36BIT_PHYS
-
-#define CONFIG_ADDR_MAP
-#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
-
-#define CONFIG_POST CONFIG_SYS_POST_MEM_REGIONS /* POST memory regions test */
-
-/*
- * Config the L3 Cache as L3 SRAM
- */
-#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE
-#define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | \
- CONFIG_RAMBOOT_TEXT_BASE)
-#define CONFIG_SYS_L3_SIZE (1024 << 10)
-#define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)
-
-#define CONFIG_SYS_DCSRBAR 0xf0000000
-#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
-
-/*
- * DDR Setup
- */
-#define CONFIG_VERY_BIG_RAM
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
-
-#define CONFIG_DDR_SPD
-
-#define CONFIG_SYS_SPD_BUS_NUM 0
-#define SPD_EEPROM_ADDRESS 0x54
-#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-
-/******************************************************************************
- * (PRAM usage)
- * ... -------------------------------------------------------
- * ... |ROOTFSSIZE | PNVRAM |PHRAM |RESERVED_PRAM | END_OF_RAM
- * ... |<------------------- pram -------------------------->|
- * ... -------------------------------------------------------
- * @END_OF_RAM:
- * @CONFIG_KM_RESERVED_PRAM: reserved pram for special purpose
- * @CONFIG_KM_PHRAM: address for /var
- * @CONFIG_KM_PNVRAM: address for PNVRAM (for the application)
- * @CONFIG_KM_ROOTFSSIZE: address for rootfilesystem in RAM
- */
-
-/* size of rootfs in RAM */
-#define CONFIG_KM_ROOTFSSIZE 0x0
-/* pseudo-non volatile RAM [hex] */
-#define CONFIG_KM_PNVRAM 0x80000
-/* physical RAM MTD size [hex] */
-#define CONFIG_KM_PHRAM 0x100000
-/* reserved pram area at the end of memory [hex]
- * u-boot reserves some memory for the MP boot page
- */
-#define CONFIG_KM_RESERVED_PRAM 0x1000
-/* set the default PRAM value to at least PNVRAM + PHRAM when pram env variable
- * is not valid yet, which is the case for when u-boot copies itself to RAM
- */
-#define CONFIG_PRAM ((CONFIG_KM_PNVRAM + CONFIG_KM_PHRAM) >> 10)
-
-#define CONFIG_KM_CRAMFS_ADDR 0x2000000
-#define CONFIG_KM_KERNEL_ADDR 0x1000000 /* max kernel size 15.5Mbytes */
-#define CONFIG_KM_FDT_ADDR 0x1F80000 /* max dtb size 0.5Mbytes */
-
-/*
- * Local Bus Definitions
- */
-
-/* Set the local bus clock 1/8 of plat clk, 2 clk delay LALE */
-#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_2)
-
-/* Nand Flash */
-#define CONFIG_NAND_FSL_ELBC
-#define CONFIG_SYS_NAND_BASE 0xffa00000
-#define CONFIG_SYS_NAND_BASE_PHYS 0xfffa00000ull
-
-#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE}
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
-
-/* NAND flash config */
-#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
- | BR_PS_8 /* Port Size = 8 bit */ \
- | BR_MS_FCM /* MSEL = FCM */ \
- | BR_V) /* valid */
-
-#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_256KB /* length 256K */ \
- | OR_FCM_BCTLD /* LBCTL not ass */ \
- | OR_FCM_SCY_1 /* 1 clk wait cycle */ \
- | OR_FCM_RST /* 1 clk read setup */ \
- | OR_FCM_PGS /* Large page size */ \
- | OR_FCM_CST) /* 0.25 command setup */
-
-#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
-#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
-
-/* QRIO FPGA */
-#define CONFIG_SYS_QRIO_BASE 0xfb000000
-#define CONFIG_SYS_QRIO_BASE_PHYS 0xffb000000ull
-
-#define CONFIG_SYS_QRIO_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_QRIO_BASE_PHYS) \
- | BR_PS_8 /* Port Size 8 bits */ \
- | BR_DECC_OFF /* no error corr */ \
- | BR_MS_GPCM /* MSEL = GPCM */ \
- | BR_V) /* valid */
-
-#define CONFIG_SYS_QRIO_OR_PRELIM (OR_AM_64KB /* length 64K */ \
- | OR_GPCM_BCTLD /* no LCTL assert */ \
- | OR_GPCM_ACS_DIV4 /* LCS 1/4 clk after */ \
- | OR_GPCM_SCY_2 /* 2 clk wait cycles */ \
- | OR_GPCM_TRLX /* relaxed tmgs */ \
- | OR_GPCM_EAD) /* extra bus clk cycles */
-
-#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_QRIO_BR_PRELIM /* QRIO Base Address */
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_QRIO_OR_PRELIM /* QRIO Options */
-
-#define CONFIG_MISC_INIT_F
-
-#define CONFIG_HWCONFIG
-
-/* define to use L1 as initial stack */
-#define CONFIG_L1_INIT_RAM
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
-/* The assembler doesn't like typecast */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
- ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
- CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
-#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)
-
-/* Serial Port - controlled on board with jumper J8
- * open - index 2
- * shorted - index 1
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0) / 2)
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x11C500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x11C600)
-#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR + 0x11D500)
-#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR + 0x11D600)
-
-#define CONFIG_KM_CONSOLE_TTY "ttyS0"
-
-/* I2C */
-/* QRIO GPIOs used for deblocking */
-#define KM_I2C_DEBLOCK_PORT QRIO_GPIO_A
-#define KM_I2C_DEBLOCK_SCL 20
-#define KM_I2C_DEBLOCK_SDA 21
-
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_INIT_BOARD
-#define CONFIG_SYS_I2C_SPEED 100000 /* deblocking */
-#define CONFIG_SYS_NUM_I2C_BUSES 3
-#define CONFIG_SYS_I2C_MAX_HOPS 1
-#define CONFIG_SYS_I2C_FSL /* Use FSL I2C driver */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_I2C_CMD_TREE
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
-#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \
- {0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \
- {0, {{I2C_MUX_PCA9547, 0x70, 2 } } }, \
- }
-#ifndef __ASSEMBLY__
-void set_sda(int state);
-void set_scl(int state);
-int get_sda(void);
-int get_scl(void);
-#endif
-
-#define CONFIG_KM_IVM_BUS 1 /* I2C1 (Mux-Port 1)*/
-
-/*
- * eSPI - Enhanced SPI
- */
-
-/*
- * General PCI
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-
-/* controller 1, direct to uli, tgtid 3, Base address 20000 */
-#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
-#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
-#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
-
-/* controller 3, Slot 1, tgtid 1, Base address 202000 */
-#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000
-#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull
-#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8010000
-#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8010000ull
-#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
-
-/* Qman/Bman */
-#define CONFIG_SYS_BMAN_NUM_PORTALS 10
-#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
-#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
-#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000
-#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000
-#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000
-#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE
-#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \
- CONFIG_SYS_BMAN_CENA_SIZE)
-#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08
-#define CONFIG_SYS_QMAN_NUM_PORTALS 10
-#define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000
-#define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull
-#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
-#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000
-#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000
-#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE
-#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \
- CONFIG_SYS_QMAN_CENA_SIZE)
-#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08
-
-#define CONFIG_SYS_DPAA_FMAN
-#define CONFIG_SYS_DPAA_PME
-/* Default address of microcode for the Linux Fman driver
- * env is stored at 0x100000, sector size is 0x10000, x2 (redundant)
- * ucode is stored after env, so we got 0x120000.
- */
-#define CONFIG_SYS_FMAN_FW_ADDR 0x120000
-#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
-#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
-
-#define CONFIG_PCI_INDIRECT_BRIDGE
-
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-
-/* RGMII (FM1 at DTESC5) is used as debug itf, it's the only one configured */
-#define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x11
-#define CONFIG_SYS_TBIPA_VALUE 8
-#define CONFIG_ETHPRIME "FM1 at DTSEC5"
-
-/*
- * Environment
- */
-#define CONFIG_LOADS_ECHO /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
-
-/*
- * Hardware Watchdog
- */
-#define CONFIG_WATCHDOG /* enable CPU watchdog */
-#define CONFIG_WATCHDOG_PRESC 34 /* wdog prescaler 2^(64-34) (~10min) */
-#define CONFIG_WATCHDOG_RC WRC_CHIP /* reset chip on watchdog event */
-
-/*
- * additionnal command line configuration.
- */
-
-/* we don't need flash support */
-#undef CONFIG_JFFS2_CMDLINE
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux */
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-
-#define __USB_PHY_TYPE utmi
-#define CONFIG_USB_EHCI_FSL
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-/* architecture specific default bootargs */
-#define CONFIG_KM_DEF_BOOT_ARGS_CPU ""
-
-/* FIXME: FDT_ADDR is unspecified */
-#define CONFIG_KM_DEF_ENV_CPU \
- "boot=bootm ${load_addr_r} - ${fdt_addr_r}\0" \
- "cramfsloadfdt=" \
- "cramfsload ${fdt_addr_r} " \
- "fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb\0" \
- "fdt_addr_r=" __stringify(CONFIG_KM_FDT_ADDR) "\0" \
- "u-boot=" CONFIG_HOSTNAME "/u-boot.pbl\0" \
- "update=" \
- "sf probe 0;sf erase 0 +${filesize};" \
- "sf write ${load_addr_r} 0 ${filesize};\0" \
- "set_fdthigh=true\0" \
- "checkfdt=true\0" \
- ""
-
-#define CONFIG_HW_ENV_SETTINGS \
- "hwconfig=fsl_ddr:ctlr_intlv=cacheline\0" \
- "usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0" \
- "usb_dr_mode=host\0"
-
-#define CONFIG_KM_NEW_ENV \
- "newenv=sf probe 0;" \
- "sf erase " __stringify(CONFIG_ENV_OFFSET) " " \
- __stringify(CONFIG_ENV_TOTAL_SIZE)"\0"
-
-/* ppc_82xx is the equivalent to ppc_6xx, the generic ppc toolchain */
-#ifndef CONFIG_KM_DEF_ARCH
-#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- CONFIG_KM_DEF_ENV \
- CONFIG_KM_DEF_ARCH \
- CONFIG_KM_NEW_ENV \
- CONFIG_HW_ENV_SETTINGS \
- "EEprom_ivm=pca9547:70:9\0" \
- ""
-
-/* App2 Local bus */
-#define CONFIG_SYS_LBAPP2_BASE 0xE0000000
-#define CONFIG_SYS_LBAPP2_BASE_PHYS 0xFE0000000ull
-
-#define CONFIG_SYS_LBAPP2_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_LBAPP2_BASE_PHYS) \
- | BR_PS_8 /* Port Size 8 bits */ \
- | BR_DECC_OFF /* no error corr */ \
- | BR_MS_GPCM /* MSEL = GPCM */ \
- | BR_V) /* valid */
-
-#define CONFIG_SYS_LBAPP2_OR_PRELIM (OR_AM_256MB /* length 256MB */ \
- | OR_GPCM_ACS_DIV2 /* LCS 1/2 clk after */ \
- | OR_GPCM_CSNT /* LCS 1/4 clk before */ \
- | OR_GPCM_SCY_2 /* 2 clk wait cycles */ \
- | OR_GPCM_TRLX /* relaxed tmgs */ \
- | OR_GPCM_EAD) /* extra bus clk cycles */
-/* Local bus app2 Base Address */
-#define CONFIG_SYS_BR3_PRELIM CONFIG_SYS_LBAPP2_BR_PRELIM
-/* Local bus app2 Options */
-#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_LBAPP2_OR_PRELIM
-
-#endif /* __CONFIG_H */
This board has not been converted to CONFIG_DM_SPI by the deadline. Remove it. Patch-cc: Valentin Longchamp <valentin.longchamp at ch.abb.com> Signed-off-by: Jagan Teki <jagan at amarulasolutions.com> --- board/keymile/Kconfig | 1 - board/keymile/kmp204x/Kconfig | 20 -- board/keymile/kmp204x/MAINTAINERS | 6 - board/keymile/kmp204x/Makefile | 10 - board/keymile/kmp204x/ddr.c | 69 ---- board/keymile/kmp204x/eth.c | 71 ----- board/keymile/kmp204x/kmp204x.c | 265 ---------------- board/keymile/kmp204x/kmp204x.h | 8 - board/keymile/kmp204x/law.c | 39 --- board/keymile/kmp204x/pbi.cfg | 74 ----- board/keymile/kmp204x/pci.c | 125 -------- board/keymile/kmp204x/rcw_kmp204x.cfg | 11 - board/keymile/kmp204x/tlb.c | 109 ------- configs/kmcoge4_defconfig | 68 ---- include/configs/kmp204x.h | 435 -------------------------- 15 files changed, 1311 deletions(-) delete mode 100644 board/keymile/kmp204x/Kconfig delete mode 100644 board/keymile/kmp204x/MAINTAINERS delete mode 100644 board/keymile/kmp204x/Makefile delete mode 100644 board/keymile/kmp204x/ddr.c delete mode 100644 board/keymile/kmp204x/eth.c delete mode 100644 board/keymile/kmp204x/kmp204x.c delete mode 100644 board/keymile/kmp204x/kmp204x.h delete mode 100644 board/keymile/kmp204x/law.c delete mode 100644 board/keymile/kmp204x/pbi.cfg delete mode 100644 board/keymile/kmp204x/pci.c delete mode 100644 board/keymile/kmp204x/rcw_kmp204x.cfg delete mode 100644 board/keymile/kmp204x/tlb.c delete mode 100644 configs/kmcoge4_defconfig delete mode 100644 include/configs/kmp204x.h