@@ -1900,7 +1900,6 @@ source "board/freescale/lx2160a/Kconfig"
source "board/freescale/mx35pdk/Kconfig"
source "board/freescale/s32v234evb/Kconfig"
source "board/grinn/chiliboard/Kconfig"
-source "board/gumstix/pepper/Kconfig"
source "board/hisilicon/hikey/Kconfig"
source "board/hisilicon/hikey960/Kconfig"
source "board/hisilicon/poplar/Kconfig"
@@ -160,13 +160,6 @@ config TARGET_PENGWYN
select DM_SERIAL
imply CMD_DM
-config TARGET_PEPPER
- bool "Support pepper"
- select DM
- select DM_GPIO
- select DM_SERIAL
- imply CMD_DM
-
config TARGET_PHYCORE_AM335X_R2
bool "Support phyCORE AM335X R2"
select DM
deleted file mode 100644
@@ -1,15 +0,0 @@
-if TARGET_PEPPER
-
-config SYS_BOARD
- default "pepper"
-
-config SYS_VENDOR
- default "gumstix"
-
-config SYS_SOC
- default "am33xx"
-
-config SYS_CONFIG_NAME
- default "pepper"
-
-endif
deleted file mode 100644
@@ -1,6 +0,0 @@
-PEPPER BOARD
-M: Ash Charles <ash at gumstix.com>
-S: Maintained
-F: board/gumstix/pepper/
-F: include/configs/pepper.h
-F: configs/pepper_defconfig
deleted file mode 100644
@@ -1,11 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Makefile
-#
-# Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
-
-ifdef CONFIG_SPL_BUILD
-obj-y += mux.o
-endif
-
-obj-y += board.o
deleted file mode 100644
@@ -1,288 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Board functions for Gumstix Pepper and AM335x-based boards
- *
- * Copyright (C) 2014, Gumstix, Incorporated - http://www.gumstix.com/
- * Based on board/ti/am335x/board.c from Texas Instruments, Inc.
- */
-
-#include <common.h>
-#include <env.h>
-#include <errno.h>
-#include <init.h>
-#include <net.h>
-#include <serial.h>
-#include <spl.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/omap.h>
-#include <asm/arch/ddr_defs.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/gpio.h>
-#include <asm/arch/mmc_host_def.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/arch/mem.h>
-#include <asm/io.h>
-#include <asm/emif.h>
-#include <asm/gpio.h>
-#include <i2c.h>
-#include <miiphy.h>
-#include <cpsw.h>
-#include <power/tps65217.h>
-#include <watchdog.h>
-#include "board.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#ifdef CONFIG_SPL_BUILD
-#define OSC (V_OSCK/1000000)
-
-static const struct ddr_data ddr3_data = {
- .datardsratio0 = MT41K256M16HA125E_RD_DQS,
- .datawdsratio0 = MT41K256M16HA125E_WR_DQS,
- .datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
- .datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
-};
-
-static const struct cmd_control ddr3_cmd_ctrl_data = {
- .cmd0csratio = MT41K256M16HA125E_RATIO,
- .cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
-
- .cmd1csratio = MT41K256M16HA125E_RATIO,
- .cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
-
- .cmd2csratio = MT41K256M16HA125E_RATIO,
- .cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
-};
-
-static struct emif_regs ddr3_emif_reg_data = {
- .sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
- .ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
- .sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
- .sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
- .sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
- .zq_config = MT41K256M16HA125E_ZQ_CFG,
- .emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY,
-};
-
-const struct dpll_params dpll_ddr3 = {400, OSC-1, 1, -1, -1, -1, -1};
-
-const struct ctrl_ioregs ioregs_ddr3 = {
- .cm0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
- .cm1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
- .cm2ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
- .dt0ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
- .dt1ioctl = MT41K256M16HA125E_IOCTRL_VALUE,
-};
-
-static const struct ddr_data ddr2_data = {
- .datardsratio0 = MT47H128M16RT25E_RD_DQS,
- .datafwsratio0 = MT47H128M16RT25E_PHY_FIFO_WE,
- .datawrsratio0 = MT47H128M16RT25E_PHY_WR_DATA,
-};
-
-static const struct cmd_control ddr2_cmd_ctrl_data = {
- .cmd0csratio = MT47H128M16RT25E_RATIO,
-
- .cmd1csratio = MT47H128M16RT25E_RATIO,
-
- .cmd2csratio = MT47H128M16RT25E_RATIO,
-};
-
-static const struct emif_regs ddr2_emif_reg_data = {
- .sdram_config = MT47H128M16RT25E_EMIF_SDCFG,
- .ref_ctrl = MT47H128M16RT25E_EMIF_SDREF,
- .sdram_tim1 = MT47H128M16RT25E_EMIF_TIM1,
- .sdram_tim2 = MT47H128M16RT25E_EMIF_TIM2,
- .sdram_tim3 = MT47H128M16RT25E_EMIF_TIM3,
- .emif_ddr_phy_ctlr_1 = MT47H128M16RT25E_EMIF_READ_LATENCY,
-};
-
-const struct dpll_params dpll_ddr2 = {266, OSC-1, 1, -1, -1, -1, -1};
-
-const struct ctrl_ioregs ioregs_ddr2 = {
- .cm0ioctl = MT47H128M16RT25E_IOCTRL_VALUE,
- .cm1ioctl = MT47H128M16RT25E_IOCTRL_VALUE,
- .cm2ioctl = MT47H128M16RT25E_IOCTRL_VALUE,
- .dt0ioctl = MT47H128M16RT25E_IOCTRL_VALUE,
- .dt1ioctl = MT47H128M16RT25E_IOCTRL_VALUE,
-};
-
-static int read_eeprom(struct pepper_board_id *header)
-{
- if (i2c_probe(CONFIG_SYS_I2C_EEPROM_ADDR)) {
- return -ENODEV;
- }
-
- if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0, 1, (uchar *)header,
- sizeof(struct pepper_board_id))) {
- return -EIO;
- }
-
- return 0;
-}
-
-const struct dpll_params *get_dpll_ddr_params(void)
-{
- struct pepper_board_id header;
-
- enable_i2c0_pin_mux();
- i2c_set_bus_num(0);
-
- if (read_eeprom(&header) < 0)
- return &dpll_ddr3;
-
- switch (header.device_vendor) {
- case GUMSTIX_PEPPER:
- return &dpll_ddr2;
- case GUMSTIX_PEPPER_DVI:
- return &dpll_ddr3;
- default:
- return &dpll_ddr3;
- }
-}
-
-void sdram_init(void)
-{
- const struct dpll_params *dpll = get_dpll_ddr_params();
-
- /*
- * Here we are assuming PLL clock reveals the type of RAM.
- * DDR2 = 266
- * DDR3 = 400
- * Note that DDR3 is the default.
- */
- if (dpll->m == 266) {
- config_ddr(dpll->m, &ioregs_ddr2, &ddr2_data,
- &ddr2_cmd_ctrl_data, &ddr2_emif_reg_data, 0);
- }
- else if (dpll->m == 400) {
- config_ddr(dpll->m, &ioregs_ddr3, &ddr3_data,
- &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);
- }
-}
-
-#ifdef CONFIG_SPL_OS_BOOT
-int spl_start_uboot(void)
-{
- /* break into full u-boot on 'c' */
- return serial_tstc() && serial_getc() == 'c';
-}
-#endif
-
-void set_uart_mux_conf(void)
-{
- enable_uart0_pin_mux();
-}
-
-void set_mux_conf_regs(void)
-{
- enable_board_pin_mux();
-}
-
-
-#endif
-
-int board_init(void)
-{
-#if defined(CONFIG_HW_WATCHDOG)
- hw_watchdog_init();
-#endif
-
- gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
- gpmc_init();
-
- return 0;
-}
-
-#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
- (defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
-static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
-
-static void cpsw_control(int enabled)
-{
- /* VTP can be added here */
-
- return;
-}
-
-static struct cpsw_slave_data cpsw_slaves[] = {
- {
- .slave_reg_ofs = 0x208,
- .sliver_reg_ofs = 0xd80,
- .phy_addr = 0,
- .phy_if = PHY_INTERFACE_MODE_RGMII,
- },
-};
-
-static struct cpsw_platform_data cpsw_data = {
- .mdio_base = CPSW_MDIO_BASE,
- .cpsw_base = CPSW_BASE,
- .mdio_div = 0xff,
- .channels = 8,
- .cpdma_reg_ofs = 0x800,
- .slaves = 1,
- .slave_data = cpsw_slaves,
- .ale_reg_ofs = 0xd00,
- .ale_entries = 1024,
- .host_port_reg_ofs = 0x108,
- .hw_stats_reg_ofs = 0x900,
- .bd_ram_ofs = 0x2000,
- .mac_control = (1 << 5),
- .control = cpsw_control,
- .host_port_num = 0,
- .version = CPSW_CTRL_VERSION_2,
-};
-
-int board_eth_init(bd_t *bis)
-{
- int rv, n = 0;
- uint8_t mac_addr[6];
- uint32_t mac_hi, mac_lo;
- const char *devname;
-
- if (!eth_env_get_enetaddr("ethaddr", mac_addr)) {
- /* try reading mac address from efuse */
- mac_lo = readl(&cdev->macid0l);
- mac_hi = readl(&cdev->macid0h);
- mac_addr[0] = mac_hi & 0xFF;
- mac_addr[1] = (mac_hi & 0xFF00) >> 8;
- mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
- mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
- mac_addr[4] = mac_lo & 0xFF;
- mac_addr[5] = (mac_lo & 0xFF00) >> 8;
- if (is_valid_ethaddr(mac_addr))
- eth_env_set_enetaddr("ethaddr", mac_addr);
- }
-
- writel((RGMII_MODE_ENABLE | RGMII_INT_DELAY), &cdev->miisel);
-
- rv = cpsw_register(&cpsw_data);
- if (rv < 0)
- printf("Error %d registering CPSW switch\n", rv);
- else
- n += rv;
-
- /*
- *
- * CPSW RGMII Internal Delay Mode is not supported in all PVT
- * operating points. So we must set the TX clock delay feature
- * in the KSZ9021 PHY. Since we only support a single ethernet
- * device in U-Boot, we only do this for the current instance.
- */
- devname = miiphy_get_current_dev();
- /* max rx/tx clock delay, min rx/tx control delay */
- miiphy_write(devname, 0x0, 0x0b, 0x8104);
- miiphy_write(devname, 0x0, 0xc, 0xa0a0);
-
- /* min rx data delay */
- miiphy_write(devname, 0x0, 0x0b, 0x8105);
- miiphy_write(devname, 0x0, 0x0c, 0x0000);
-
- /* min tx data delay */
- miiphy_write(devname, 0x0, 0x0b, 0x8106);
- miiphy_write(devname, 0x0, 0x0c, 0x0000);
-
- return n;
-}
-#endif
deleted file mode 100644
@@ -1,31 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Gumstix Pepper and AM335x-based boards information header
- *
- * Copyright (C) 2014, Gumstix, Inc. - http://www.gumstix.com/
- */
-
-#ifndef _BOARD_H_
-#define _BOARD_H_
-
-#define GUMSTIX_PEPPER 0x30000200
-#define GUMSTIX_PEPPER_DVI 0x31000200
-
-struct pepper_board_id {
- unsigned int device_vendor;
- unsigned char revision;
- unsigned char content;
- char fab_revision[8];
- char env_var[16];
- char en_setting[64];
-};
-
-/*
- * We must be able to enable uart0, for initial output. We then have a
- * main pinmux function that can be overridden to enable all other pinmux that
- * is required on the board.
- */
-void enable_uart0_pin_mux(void);
-void enable_board_pin_mux(void);
-void enable_i2c0_pin_mux(void);
-#endif
deleted file mode 100644
@@ -1,82 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Muxing for Gumstix Pepper and AM335x-based boards
- *
- * Copyright (C) 2014, Gumstix, Incorporated - http://www.gumstix.com/
- */
-#include <common.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/mux.h>
-#include <asm/io.h>
-#include <i2c.h>
-#include "board.h"
-
-static struct module_pin_mux uart0_pin_mux[] = {
- {OFFSET(uart0_rxd), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* UART0_RXD */
- {OFFSET(uart0_txd), (MODE(0) | PULLUDEN)}, /* UART0_TXD */
- {-1},
-};
-
-static struct module_pin_mux mmc0_pin_mux[] = {
- {OFFSET(mmc0_dat3), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT3 */
- {OFFSET(mmc0_dat2), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT2 */
- {OFFSET(mmc0_dat1), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT1 */
- {OFFSET(mmc0_dat0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT0 */
- {OFFSET(mmc0_clk), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_CLK */
- {OFFSET(mmc0_cmd), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_CMD */
- {OFFSET(spi0_cs1), (MODE(5) | RXACTIVE | PULLUP_EN)}, /* MMC0_CD */
- {-1},
-};
-
-static struct module_pin_mux i2c0_pin_mux[] = {
- /* I2C_DATA */
- {OFFSET(i2c0_sda), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)},
- /* I2C_SCLK */
- {OFFSET(i2c0_scl), (MODE(0) | RXACTIVE | PULLUDEN | SLEWCTRL)},
- {-1},
-};
-
-static struct module_pin_mux rgmii1_pin_mux[] = {
- {OFFSET(mii1_txen), MODE(2)}, /* RGMII1_TCTL */
- {OFFSET(mii1_rxdv), MODE(2) | RXACTIVE}, /* RGMII1_RCTL */
- {OFFSET(mii1_txd3), MODE(2)}, /* RGMII1_TD3 */
- {OFFSET(mii1_txd2), MODE(2)}, /* RGMII1_TD2 */
- {OFFSET(mii1_txd1), MODE(2)}, /* RGMII1_TD1 */
- {OFFSET(mii1_txd0), MODE(2)}, /* RGMII1_TD0 */
- {OFFSET(mii1_txclk), MODE(2)}, /* RGMII1_TCLK */
- {OFFSET(mii1_rxclk), MODE(2) | RXACTIVE}, /* RGMII1_RCLK */
- {OFFSET(mii1_rxd3), MODE(2) | RXACTIVE}, /* RGMII1_RD3 */
- {OFFSET(mii1_rxd2), MODE(2) | RXACTIVE}, /* RGMII1_RD2 */
- {OFFSET(mii1_rxd1), MODE(2) | RXACTIVE}, /* RGMII1_RD1 */
- {OFFSET(mii1_rxd0), MODE(2) | RXACTIVE}, /* RGMII1_RD0 */
- {OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN},/* MDIO_DATA */
- {OFFSET(mdio_clk), MODE(0) | PULLUP_EN}, /* MDIO_CLK */
- {OFFSET(rmii1_refclk), MODE(7) | RXACTIVE}, /* ETH_INT */
- {OFFSET(mii1_col), MODE(7) | PULLUP_EN}, /* PHY_NRESET */
- {OFFSET(xdma_event_intr1), MODE(3)},
- {-1},
-};
-
-void enable_uart0_pin_mux(void)
-{
- configure_module_pin_mux(uart0_pin_mux);
-}
-
-void enable_i2c0_pin_mux(void)
-{
- configure_module_pin_mux(i2c0_pin_mux);
-}
-
-/*
- * Do board-specific muxes.
- */
-void enable_board_pin_mux(void)
-{
- /* I2C0 */
- configure_module_pin_mux(i2c0_pin_mux);
- /* SD Card */
- configure_module_pin_mux(mmc0_pin_mux);
- /* Ethernet pinmux. */
- configure_module_pin_mux(rgmii1_pin_mux);
-}
deleted file mode 100644
@@ -1,42 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_CPU_INIT=y
-CONFIG_ARCH_OMAP2PLUS=y
-CONFIG_SPL_GPIO_SUPPORT=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_AM33XX=y
-CONFIG_TARGET_PEPPER=y
-CONFIG_SPL_MMC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_SPL_FS_FAT=y
-CONFIG_SPL_LIBDISK_SUPPORT=y
-CONFIG_DISTRO_DEFAULTS=y
-# CONFIG_USE_BOOTCOMMAND is not set
-CONFIG_SYS_CONSOLE_INFO_QUIET=y
-CONFIG_VERSION_VARIABLE=y
-CONFIG_SPL_FS_EXT4=y
-CONFIG_SPL_I2C_SUPPORT=y
-# CONFIG_SPL_NAND_SUPPORT is not set
-CONFIG_SPL_POWER_SUPPORT=y
-CONFIG_SPL_WATCHDOG_SUPPORT=y
-CONFIG_SYS_PROMPT="pepper# "
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SPI=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
-CONFIG_MMC_OMAP_HS=y
-CONFIG_PHY_ADDR_ENABLE=y
-CONFIG_PHY_MICREL=y
-CONFIG_PHY_MICREL_KSZ90X1=y
-CONFIG_MII=y
-CONFIG_DRIVER_TI_CPSW=y
-CONFIG_SPI=y
-CONFIG_OMAP3_SPI=y
-CONFIG_FAT_WRITE=y
-CONFIG_OF_LIBFDT=y
deleted file mode 100644
@@ -1,78 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2013 Gumstix, Inc. - http://www.gumstix.com/
- */
-
-#ifndef __CONFIG_PEPPER_H
-#define __CONFIG_PEPPER_H
-
-#include <configs/ti_am335x_common.h>
-
-/* Clock defines */
-#define V_OSCK 24000000 /* Clock output from T2 */
-#define V_SCLK (V_OSCK)
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-
-/* Mach type */
-#define CONFIG_MACH_TYPE MACH_TYPE_PEPPER
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- DEFAULT_LINUX_BOOT_ENV \
- "bootdir=/boot\0" \
- "bootfile=zImage\0" \
- "fdtfile=am335x-pepper.dtb\0" \
- "console=ttyO0,115200n8\0" \
- "optargs=\0" \
- "mmcdev=0\0" \
- "mmcroot=/dev/mmcblk0p2 rw\0" \
- "mmcrootfstype=ext4 rootwait\0" \
- "mmcargs=setenv bootargs console=${console} " \
- "${optargs} " \
- "root=${mmcroot} " \
- "rootfstype=${mmcrootfstype}\0" \
- "bootenv=uEnv.txt\0" \
- "loadbootenv=load mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
- "importbootenv=echo Importing environment from mmc ...; " \
- "env import -t ${loadaddr} ${filesize}\0" \
- "mmcload=load mmc ${mmcdev}:2 ${loadaddr} ${bootdir}/${bootfile}; " \
- "load mmc ${mmcdev}:2 ${fdtaddr} ${bootdir}/${fdtfile}\0" \
- "loaduimage=fatload mmc ${mmcdev}:1 ${loadaddr} uImage\0" \
- "uimageboot=echo Booting from mmc${mmcdev} ...; " \
- "run mmcargs; " \
- "bootm ${loadaddr}\0" \
- "mmcboot=echo Booting from mmc ...; " \
- "run mmcargs; " \
- "bootz ${loadaddr} - ${fdtaddr}\0" \
- "ubiboot=echo Booting from nand (ubifs) ...; " \
- "run ubiargs; run ubiload; " \
- "bootz ${loadaddr} - ${fdtaddr}\0" \
-
-#define CONFIG_BOOTCOMMAND \
- "mmc dev ${mmcdev}; if mmc rescan; then " \
- "echo SD/MMC found on device ${mmcdev};" \
- "if run loadbootenv; then " \
- "echo Loaded environment from ${bootenv};" \
- "run importbootenv;" \
- "fi;" \
- "if test -n $uenvcmd; then " \
- "echo Running uenvcmd ...;" \
- "run uenvcmd;" \
- "fi;" \
- "if run mmcload; then " \
- "run mmcboot;" \
- "fi;" \
- "if run loaduimage; then " \
- "run uimageboot;" \
- "fi;" \
- "fi;" \
-
-/* Serial console configuration */
-#define CONFIG_SYS_NS16550_COM1 0x44e09000
-
-/* Ethernet support */
-#define CONFIG_PHY_RESET_DELAY 1000
-
-/* SPL */
-
-#endif /* __CONFIG_PEPPER_H */
OF_CONTROL, DM_SPI and other driver model migration deadlines are expired for this board. Drop it. Cc: Ash Charles <ash at gumstix.com> Signed-off-by: Jagan Teki <jagan at amarulasolutions.com> --- Changes for v2: - new patch arch/arm/Kconfig | 1 - arch/arm/mach-omap2/am33xx/Kconfig | 7 - board/gumstix/pepper/Kconfig | 15 -- board/gumstix/pepper/MAINTAINERS | 6 - board/gumstix/pepper/Makefile | 11 -- board/gumstix/pepper/board.c | 288 ----------------------------- board/gumstix/pepper/board.h | 31 ---- board/gumstix/pepper/mux.c | 82 -------- configs/pepper_defconfig | 42 ----- include/configs/pepper.h | 78 -------- 10 files changed, 561 deletions(-) delete mode 100644 board/gumstix/pepper/Kconfig delete mode 100644 board/gumstix/pepper/MAINTAINERS delete mode 100644 board/gumstix/pepper/Makefile delete mode 100644 board/gumstix/pepper/board.c delete mode 100644 board/gumstix/pepper/board.h delete mode 100644 board/gumstix/pepper/mux.c delete mode 100644 configs/pepper_defconfig delete mode 100644 include/configs/pepper.h