@@ -9,9 +9,6 @@ choice
prompt "OMAP5 board select"
optional
-config TARGET_OMAP5_UEVM
- bool "TI OMAP5 uEVM board"
-
config TARGET_DRA7XX_EVM
bool "TI DRA7XX"
select BOARD_LATE_INIT
@@ -153,7 +150,6 @@ endchoice
endmenu
endif
-source "board/ti/omap5_uevm/Kconfig"
source "board/ti/dra7xx/Kconfig"
source "board/ti/am57xx/Kconfig"
deleted file mode 100644
@@ -1,12 +0,0 @@
-if TARGET_OMAP5_UEVM
-
-config SYS_BOARD
- default "omap5_uevm"
-
-config SYS_VENDOR
- default "ti"
-
-config SYS_CONFIG_NAME
- default "omap5_uevm"
-
-endif
deleted file mode 100644
@@ -1,6 +0,0 @@
-OMAP5_UEVM BOARD
-M: Lokesh Vutla <lokeshvutla at ti.com>
-S: Maintained
-F: board/ti/omap5_uevm/
-F: include/configs/omap5_uevm.h
-F: configs/omap5_uevm_defconfig
deleted file mode 100644
@@ -1,6 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2000, 2001, 2002
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-
-obj-y := evm.o
deleted file mode 100644
@@ -1,25 +0,0 @@
-Summary
-=======
-
-This document covers various features of the 'omap5_uevm' build and some
-related uses.
-
-eMMC boot partition use
-=======================
-
-It is possible, depending on SYSBOOT configuration to boot from the eMMC
-boot partitions using (name depending on documentation referenced)
-Alternative Boot operation mode or Boot Sequence Option 1/2. In this
-example we load MLO and u-boot.img from the build into DDR and then use
-'mmc bootbus' to set the required rate (see TRM) and 'mmc partconfig' to
-set boot0 as the boot device.
-U-Boot # setenv autoload no
-U-Boot # usb start
-U-Boot # dhcp
-U-Boot # mmc dev 1 1
-U-Boot # tftp ${loadaddr} omap5uevm/MLO
-U-Boot # mmc write ${loadaddr} 0 100
-U-Boot # tftp ${loadaddr} omap5uevm/u-boot.img
-U-Boot # mmc write ${loadaddr} 300 400
-U-Boot # mmc bootbus 1 2 0 2
-U-Boot # mmc partconf 1 1 1 0
deleted file mode 100644
@@ -1,283 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2010
- * Texas Instruments Incorporated, <www.ti.com>
- * Aneesh V <aneesh at ti.com>
- * Steve Sakoman <steve at sakoman.com>
- */
-#include <common.h>
-#include <init.h>
-#include <net.h>
-#include <palmas.h>
-#include <asm/arch/omap.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/arch/mmc_host_def.h>
-#include <tca642x.h>
-#include <usb.h>
-#include <linux/delay.h>
-#include <linux/usb/gadget.h>
-#include <dwc3-uboot.h>
-#include <dwc3-omap-uboot.h>
-#include <ti-usb-phy-uboot.h>
-
-#include "mux_data.h"
-
-#if defined(CONFIG_USB_EHCI_HCD) || defined(CONFIG_USB_XHCI_OMAP)
-#include <sata.h>
-#include <usb.h>
-#include <asm/gpio.h>
-#include <asm/mach-types.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/ehci.h>
-#include <asm/ehci-omap.h>
-#include <asm/arch/sata.h>
-
-#define DIE_ID_REG_BASE (OMAP54XX_L4_CORE_BASE + 0x2000)
-#define DIE_ID_REG_OFFSET 0x200
-
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-const struct omap_sysinfo sysinfo = {
- "Board: OMAP5432 uEVM\n"
-};
-
-/**
- * @brief tca642x_init - uEVM default values for the GPIO expander
- * input reg, output reg, polarity reg, configuration reg
- */
-struct tca642x_bank_info tca642x_init[] = {
- { .input_reg = 0x00,
- .output_reg = 0x04,
- .polarity_reg = 0x00,
- .configuration_reg = 0x80 },
- { .input_reg = 0x00,
- .output_reg = 0x00,
- .polarity_reg = 0x00,
- .configuration_reg = 0xff },
- { .input_reg = 0x00,
- .output_reg = 0x00,
- .polarity_reg = 0x00,
- .configuration_reg = 0x40 },
-};
-
-#ifdef CONFIG_USB_DWC3
-static struct dwc3_device usb_otg_ss = {
- .maximum_speed = USB_SPEED_SUPER,
- .base = OMAP5XX_USB_OTG_SS_BASE,
- .tx_fifo_resize = false,
- .index = 0,
-};
-
-static struct dwc3_omap_device usb_otg_ss_glue = {
- .base = (void *)OMAP5XX_USB_OTG_SS_GLUE_BASE,
- .utmi_mode = DWC3_OMAP_UTMI_MODE_SW,
- .index = 0,
-};
-
-static struct ti_usb_phy_device usb_phy_device = {
- .pll_ctrl_base = (void *)OMAP5XX_USB3_PHY_PLL_CTRL,
- .usb2_phy_power = (void *)OMAP5XX_USB2_PHY_POWER,
- .usb3_phy_power = (void *)OMAP5XX_USB3_PHY_POWER,
- .index = 0,
-};
-
-int board_usb_init(int index, enum usb_init_type init)
-{
- if (index) {
- printf("Invalid Controller Index\n");
- return -EINVAL;
- }
-
- if (init == USB_INIT_DEVICE) {
- usb_otg_ss.dr_mode = USB_DR_MODE_PERIPHERAL;
- usb_otg_ss_glue.vbus_id_status = OMAP_DWC3_VBUS_VALID;
- } else {
- usb_otg_ss.dr_mode = USB_DR_MODE_HOST;
- usb_otg_ss_glue.vbus_id_status = OMAP_DWC3_ID_GROUND;
- }
-
- enable_usb_clocks(index);
- ti_usb_phy_uboot_init(&usb_phy_device);
- dwc3_omap_uboot_init(&usb_otg_ss_glue);
- dwc3_uboot_init(&usb_otg_ss);
-
- return 0;
-}
-
-int board_usb_cleanup(int index, enum usb_init_type init)
-{
- if (index) {
- printf("Invalid Controller Index\n");
- return -EINVAL;
- }
-
- ti_usb_phy_uboot_exit(index);
- dwc3_uboot_exit(index);
- dwc3_omap_uboot_exit(index);
- disable_usb_clocks(index);
-
- return 0;
-}
-
-int usb_gadget_handle_interrupts(int index)
-{
- u32 status;
-
- status = dwc3_omap_uboot_interrupt_status(index);
- if (status)
- dwc3_uboot_handle_interrupt(index);
-
- return 0;
-}
-#endif
-
-/**
- * @brief board_init
- *
- * @return 0
- */
-int board_init(void)
-{
- gpmc_init();
- gd->bd->bi_arch_number = MACH_TYPE_OMAP5_SEVM;
- gd->bd->bi_boot_params = (0x80000000 + 0x100); /* boot param addr */
-
- tca642x_set_inital_state(CONFIG_SYS_I2C_TCA642X_ADDR, tca642x_init);
-
- return 0;
-}
-
-int board_eth_init(bd_t *bis)
-{
- return 0;
-}
-
-#if defined(CONFIG_USB_EHCI_HCD) || defined(CONFIG_USB_XHCI_OMAP)
-static void enable_host_clocks(void)
-{
- int auxclk;
- int hs_clk_ctrl_val = (OPTFCLKEN_HSIC60M_P3_CLK |
- OPTFCLKEN_HSIC480M_P3_CLK |
- OPTFCLKEN_HSIC60M_P2_CLK |
- OPTFCLKEN_HSIC480M_P2_CLK |
- OPTFCLKEN_UTMI_P3_CLK | OPTFCLKEN_UTMI_P2_CLK);
-
- /* Enable port 2 and 3 clocks*/
- setbits_le32((*prcm)->cm_l3init_hsusbhost_clkctrl, hs_clk_ctrl_val);
-
- /* Enable port 2 and 3 usb host ports tll clocks*/
- setbits_le32((*prcm)->cm_l3init_hsusbtll_clkctrl,
- (OPTFCLKEN_USB_CH1_CLK_ENABLE | OPTFCLKEN_USB_CH2_CLK_ENABLE));
-#ifdef CONFIG_USB_XHCI_OMAP
- /* Enable the USB OTG Super speed clocks */
- setbits_le32((*prcm)->cm_l3init_usb_otg_ss_clkctrl,
- (OPTFCLKEN_REFCLK960M | OTG_SS_CLKCTRL_MODULEMODE_HW));
-#endif
-
- auxclk = readl((*prcm)->scrm_auxclk1);
- /* Request auxilary clock */
- auxclk |= AUXCLK_ENABLE_MASK;
- writel(auxclk, (*prcm)->scrm_auxclk1);
-}
-#endif
-
-/**
- * @brief misc_init_r - Configure EVM board specific configurations
- * such as power configurations, ethernet initialization as phase2 of
- * boot sequence
- *
- * @return 0
- */
-int misc_init_r(void)
-{
-#ifdef CONFIG_PALMAS_POWER
- palmas_init_settings();
-#endif
-
- omap_die_id_usbethaddr();
-
- return 0;
-}
-
-void set_muxconf_regs(void)
-{
- do_set_mux((*ctrl)->control_padconf_core_base,
- core_padconf_array_essential,
- sizeof(core_padconf_array_essential) /
- sizeof(struct pad_conf_entry));
-
- do_set_mux((*ctrl)->control_padconf_wkup_base,
- wkup_padconf_array_essential,
- sizeof(wkup_padconf_array_essential) /
- sizeof(struct pad_conf_entry));
-}
-
-#if defined(CONFIG_MMC)
-int board_mmc_init(bd_t *bis)
-{
- omap_mmc_init(0, 0, 0, -1, -1);
- omap_mmc_init(1, 0, 0, -1, -1);
- return 0;
-}
-#endif
-
-#ifdef CONFIG_USB_EHCI_HCD
-static struct omap_usbhs_board_data usbhs_bdata = {
- .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
- .port_mode[1] = OMAP_EHCI_PORT_MODE_HSIC,
- .port_mode[2] = OMAP_EHCI_PORT_MODE_HSIC,
-};
-
-int ehci_hcd_init(int index, enum usb_init_type init,
- struct ehci_hccr **hccr, struct ehci_hcor **hcor)
-{
- int ret;
-
- enable_host_clocks();
-
- ret = omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor);
- if (ret < 0) {
- puts("Failed to initialize ehci\n");
- return ret;
- }
-
- return 0;
-}
-
-int ehci_hcd_stop(void)
-{
- return omap_ehci_hcd_stop();
-}
-
-void usb_hub_reset_devices(struct usb_hub_device *hub, int port)
-{
- /* The LAN9730 needs to be reset after the port power has been set. */
- if (port == 3) {
- gpio_direction_output(CONFIG_OMAP_EHCI_PHY3_RESET_GPIO, 0);
- udelay(10);
- gpio_direction_output(CONFIG_OMAP_EHCI_PHY3_RESET_GPIO, 1);
- }
-}
-#endif
-
-#ifdef CONFIG_USB_XHCI_OMAP
-/**
- * @brief board_usb_init - Configure EVM board specific configurations
- * for the LDO's and clocks for the USB blocks.
- *
- * @return 0
- */
-int board_usb_init(int index, enum usb_init_type init)
-{
- int ret;
-#ifdef CONFIG_PALMAS_USB_SS_PWR
- ret = palmas_enable_ss_ldo();
-#endif
-
- enable_host_clocks();
-
- return 0;
-}
-#endif
deleted file mode 100644
@@ -1,57 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2010
- * Texas Instruments Incorporated, <www.ti.com>
- *
- * Sricharan R <r.sricharan at ti.com>
- */
-#ifndef _EVM5430_MUX_DATA_H
-#define _EVM5430_MUX_DATA_H
-
-#include <asm/arch/mux_omap5.h>
-
-const struct pad_conf_entry core_padconf_array_essential[] = {
-
- {EMMC_CLK, (PTU | IEN | M0)}, /* EMMC_CLK */
- {EMMC_CMD, (PTU | IEN | M0)}, /* EMMC_CMD */
- {EMMC_DATA0, (PTU | IEN | M0)}, /* EMMC_DATA0 */
- {EMMC_DATA1, (PTU | IEN | M0)}, /* EMMC_DATA1 */
- {EMMC_DATA2, (PTU | IEN | M0)}, /* EMMC_DATA2 */
- {EMMC_DATA3, (PTU | IEN | M0)}, /* EMMC_DATA3 */
- {EMMC_DATA4, (PTU | IEN | M0)}, /* EMMC_DATA4 */
- {EMMC_DATA5, (PTU | IEN | M0)}, /* EMMC_DATA5 */
- {EMMC_DATA6, (PTU | IEN | M0)}, /* EMMC_DATA6 */
- {EMMC_DATA7, (PTU | IEN | M0)}, /* EMMC_DATA7 */
- {SDCARD_CLK, (PTU | IEN | M0)}, /* SDCARD_CLK */
- {SDCARD_CMD, (PTU | IEN | M0)}, /* SDCARD_CMD */
- {SDCARD_DATA0, (PTU | IEN | M0)}, /* SDCARD_DATA0*/
- {SDCARD_DATA1, (PTU | IEN | M0)}, /* SDCARD_DATA1*/
- {SDCARD_DATA2, (PTU | IEN | M0)}, /* SDCARD_DATA2*/
- {SDCARD_DATA3, (PTU | IEN | M0)}, /* SDCARD_DATA3*/
- {UART3_RX_IRRX, (PTU | IEN | M0)}, /* UART3_RX_IRRX */
- {UART3_TX_IRTX, (M0)}, /* UART3_TX_IRTX */
- {USBB1_HSIC_STROBE, (PTU | IEN | M0)}, /* USBB1_HSIC_STROBE */
- {USBB1_HSIC_DATA, (PTU | IEN | M0)}, /* USBB1_HSIC_DATA */
- {USBB2_HSIC_STROBE, (PTU | IEN | M0)}, /* USBB2_HSIC_STROBE */
- {USBB2_HSIC_DATA, (PTU | IEN | M0)}, /* USBB2_HSIC_DATA */
- {USBB3_HSIC_STROBE, (PTU | IEN | M0)}, /* USBB3_HSIC_STROBE*/
- {USBB3_HSIC_DATA, (PTU | IEN | M0)}, /* USBB3_HSIC_DATA */
- {USBD0_HS_DP, (IEN | M0)}, /* USBD0_HS_DP */
- {USBD0_HS_DM, (IEN | M0)}, /* USBD0_HS_DM */
- {USBD0_SS_RX, (IEN | M0)}, /* USBD0_SS_RX */
- {I2C5_SCL, (IEN | M0)}, /* I2C5_SCL */
- {I2C5_SDA, (IEN | M0)}, /* I2C5_SDA */
- {HSI2_ACWAKE, (PTU | M6)}, /* HSI2_ACWAKE */
- {HSI2_CAFLAG, (PTU | M6)}, /* HSI2_CAFLAG */
-};
-
-const struct pad_conf_entry wkup_padconf_array_essential[] = {
-
- {SR_PMIC_SCL, (PTU | IEN | M0)}, /* SR_PMIC_SCL */
- {SR_PMIC_SDA, (PTU | IEN | M0)}, /* SR_PMIC_SDA */
- {SYS_32K, (IEN | M0)}, /* SYS_32K */
- {FREF_CLK1_OUT, (PTD | IEN | M0)}, /* FREF_CLK1_OUT */
-
-};
-
-#endif /* _EVM4430_MUX_DATA_H */
deleted file mode 100644
@@ -1,55 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_OMAP2PLUS=y
-CONFIG_OMAP54XX=y
-CONFIG_TARGET_OMAP5_UEVM=y
-CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC=16296
-CONFIG_SPL=y
-CONFIG_ENV_OFFSET_REDUND=0x280000
-CONFIG_ARMV7_LPAE=y
-CONFIG_SPL_TEXT_BASE=0x40300000
-CONFIG_DISTRO_DEFAULTS=y
-# CONFIG_USE_BOOTCOMMAND is not set
-CONFIG_SYS_CONSOLE_INFO_QUIET=y
-CONFIG_VERSION_VARIABLE=y
-# CONFIG_SPL_NAND_SUPPORT is not set
-CONFIG_SPL_OS_BOOT=y
-CONFIG_CMD_SPL=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_DFU=y
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SPI=y
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
-CONFIG_SCSI_AHCI=y
-CONFIG_DFU_MMC=y
-CONFIG_DFU_RAM=y
-CONFIG_CMD_TCA642X=y
-CONFIG_SUPPORT_EMMC_BOOT=y
-CONFIG_MMC_OMAP_HS=y
-CONFIG_SCSI=y
-CONFIG_CONS_INDEX=3
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_OMAP3_SPI=y
-CONFIG_USB=y
-CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_DWC3=y
-CONFIG_USB_DWC3_OMAP=y
-CONFIG_USB_DWC3_PHY_OMAP=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments"
-CONFIG_USB_GADGET_VENDOR_NUM=0x0403
-CONFIG_USB_GADGET_PRODUCT_NUM=0xbd00
-CONFIG_USB_GADGET_DOWNLOAD=y
-CONFIG_USB_HOST_ETHER=y
-CONFIG_USB_ETHER_SMSC95XX=y
-CONFIG_FAT_WRITE=y
-CONFIG_OF_LIBFDT=y
deleted file mode 100644
@@ -1,62 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2013
- * Texas Instruments Incorporated.
- * Sricharan R <r.sricharan at ti.com>
- *
- * Configuration settings for the TI EVM5430 board.
- * See ti_omap5_common.h for omap5 common settings.
- */
-
-#ifndef __CONFIG_OMAP5_EVM_H
-#define __CONFIG_OMAP5_EVM_H
-
-#include <environment/ti/dfu.h>
-
-#ifndef CONFIG_SPL_BUILD
-/* Define the default GPT table for eMMC */
-#define PARTS_DEFAULT \
- "uuid_disk=${uuid_gpt_disk};" \
- "name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}"
-#endif
-
-#define DFUARGS \
- "dfu_bufsiz=0x10000\0" \
- DFU_ALT_INFO_MMC \
- DFU_ALT_INFO_EMMC \
- DFU_ALT_INFO_RAM
-
-#include <configs/ti_omap5_common.h>
-
-#define CONFIG_SYS_NS16550_COM3 UART3_BASE
-
-/* MMC ENV related defines */
-#define CONFIG_SYS_MMC_ENV_DEV 1 /* SLOT2: eMMC(1) */
-
-/* Enhance our eMMC support / experience. */
-#define CONFIG_HSMMC2_8BIT
-
-/* Required support for the TCA642X GPIO we have on the uEVM */
-#define CONFIG_TCA642X
-#define CONFIG_SYS_I2C_TCA642X_BUS_NUM 4
-#define CONFIG_SYS_I2C_TCA642X_ADDR 0x22
-
-/* USB UHH support options */
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-
-#define CONFIG_OMAP_EHCI_PHY2_RESET_GPIO 80
-#define CONFIG_OMAP_EHCI_PHY3_RESET_GPIO 79
-
-/* Enabled commands */
-
-/* USB Networking options */
-
-#define CONSOLEDEV "ttyS2"
-
-#define CONFIG_SCSI_AHCI_PLAT
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
- CONFIG_SYS_SCSI_MAX_LUN)
-
-#endif /* __CONFIG_OMAP5_EVM_H */
DM, DM_SPI and other driver model migration deadlines are expired for this board. Drop it. Cc: Lokesh Vutla <lokeshvutla at ti.com> Signed-off-by: Jagan Teki <jagan at amarulasolutions.com> --- Changes for v2: - none arch/arm/mach-omap2/omap5/Kconfig | 4 - board/ti/omap5_uevm/Kconfig | 12 -- board/ti/omap5_uevm/MAINTAINERS | 6 - board/ti/omap5_uevm/Makefile | 6 - board/ti/omap5_uevm/README | 25 --- board/ti/omap5_uevm/evm.c | 283 ------------------------------ board/ti/omap5_uevm/mux_data.h | 57 ------ configs/omap5_uevm_defconfig | 55 ------ include/configs/omap5_uevm.h | 62 ------- 9 files changed, 510 deletions(-) delete mode 100644 board/ti/omap5_uevm/Kconfig delete mode 100644 board/ti/omap5_uevm/MAINTAINERS delete mode 100644 board/ti/omap5_uevm/Makefile delete mode 100644 board/ti/omap5_uevm/README delete mode 100644 board/ti/omap5_uevm/evm.c delete mode 100644 board/ti/omap5_uevm/mux_data.h delete mode 100644 configs/omap5_uevm_defconfig delete mode 100644 include/configs/omap5_uevm.h