From patchwork Sun Apr 19 15:48:50 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: =?utf-8?q?Marek_Beh=C3=BAn?= X-Patchwork-Id: 238032 List-Id: U-Boot discussion From: marek.behun at nic.cz (=?UTF-8?q?Marek=20Beh=C3=BAn?=) Date: Sun, 19 Apr 2020 17:48:50 +0200 Subject: [PATCH u-boot-marvell 11/11] phy: marvell: remove comphy_a3700 driver In-Reply-To: <20200419154850.25868-1-marek.behun@nic.cz> References: <20200419154850.25868-1-marek.behun@nic.cz> Message-ID: <20200419154850.25868-12-marek.behun@nic.cz> This driver is no longer needed since A37xx was ported to generic-phy. The only thing not covered by those drivers is eMMC PHY init code, but even this is already done in different driver (xenon_sdhci). Signed-off-by: Marek Beh?n --- drivers/phy/marvell/Makefile | 1 - drivers/phy/marvell/comphy_a3700.c | 1021 ---------------------------- drivers/phy/marvell/comphy_a3700.h | 264 ------- drivers/phy/marvell/comphy_core.c | 3 - drivers/phy/marvell/comphy_core.h | 25 +- include/mvebu/comphy.h | 22 - 6 files changed, 9 insertions(+), 1327 deletions(-) delete mode 100644 drivers/phy/marvell/comphy_a3700.c delete mode 100644 drivers/phy/marvell/comphy_a3700.h delete mode 100644 include/mvebu/comphy.h diff --git a/drivers/phy/marvell/Makefile b/drivers/phy/marvell/Makefile index 51be0399ea..7d17b2dc60 100644 --- a/drivers/phy/marvell/Makefile +++ b/drivers/phy/marvell/Makefile @@ -2,5 +2,4 @@ obj-$(CONFIG_MVEBU_COMPHY_SUPPORT) += comphy_core.o obj-$(CONFIG_MVEBU_COMPHY_SUPPORT) += comphy_mux.o -obj-$(CONFIG_ARMADA_3700) += comphy_a3700.o obj-$(CONFIG_ARMADA_8K) += comphy_cp110.o diff --git a/drivers/phy/marvell/comphy_a3700.c b/drivers/phy/marvell/comphy_a3700.c deleted file mode 100644 index 3b2902f362..0000000000 --- a/drivers/phy/marvell/comphy_a3700.c +++ /dev/null @@ -1,1021 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright (C) 2015-2016 Marvell International Ltd. - */ - -#include -#include -#include -#include -#include - -#include "comphy_a3700.h" - -DECLARE_GLOBAL_DATA_PTR; - -struct comphy_mux_data a3700_comphy_mux_data[] = { -/* Lane 0 */ - { - 4, - { - { PHY_TYPE_UNCONNECTED, 0x0 }, - { PHY_TYPE_SGMII1, 0x0 }, - { PHY_TYPE_USB3_HOST0, 0x1 }, - { PHY_TYPE_USB3_DEVICE, 0x1 } - } - }, -/* Lane 1 */ - { - 3, - { - { PHY_TYPE_UNCONNECTED, 0x0}, - { PHY_TYPE_SGMII0, 0x0}, - { PHY_TYPE_PEX0, 0x1} - } - }, -/* Lane 2 */ - { - 4, - { - { PHY_TYPE_UNCONNECTED, 0x0}, - { PHY_TYPE_SATA0, 0x0}, - { PHY_TYPE_USB3_HOST0, 0x1}, - { PHY_TYPE_USB3_DEVICE, 0x1} - } - }, -}; - -struct sgmii_phy_init_data_fix { - u16 addr; - u16 value; -}; - -/* Changes to 40M1G25 mode data required for running 40M3G125 init mode */ -static struct sgmii_phy_init_data_fix sgmii_phy_init_fix[] = { - {0x005, 0x07CC}, {0x015, 0x0000}, {0x01B, 0x0000}, {0x01D, 0x0000}, - {0x01E, 0x0000}, {0x01F, 0x0000}, {0x020, 0x0000}, {0x021, 0x0030}, - {0x026, 0x0888}, {0x04D, 0x0152}, {0x04F, 0xA020}, {0x050, 0x07CC}, - {0x053, 0xE9CA}, {0x055, 0xBD97}, {0x071, 0x3015}, {0x076, 0x03AA}, - {0x07C, 0x0FDF}, {0x0C2, 0x3030}, {0x0C3, 0x8000}, {0x0E2, 0x5550}, - {0x0E3, 0x12A4}, {0x0E4, 0x7D00}, {0x0E6, 0x0C83}, {0x101, 0xFCC0}, - {0x104, 0x0C10} -}; - -/* 40M1G25 mode init data */ -static u16 sgmii_phy_init[512] = { - /* 0 1 2 3 4 5 6 7 */ - /*-----------------------------------------------------------*/ - /* 8 9 A B C D E F */ - 0x3110, 0xFD83, 0x6430, 0x412F, 0x82C0, 0x06FA, 0x4500, 0x6D26, /* 00 */ - 0xAFC0, 0x8000, 0xC000, 0x0000, 0x2000, 0x49CC, 0x0BC9, 0x2A52, /* 08 */ - 0x0BD2, 0x0CDE, 0x13D2, 0x0CE8, 0x1149, 0x10E0, 0x0000, 0x0000, /* 10 */ - 0x0000, 0x0000, 0x0000, 0x0001, 0x0000, 0x4134, 0x0D2D, 0xFFFF, /* 18 */ - 0xFFE0, 0x4030, 0x1016, 0x0030, 0x0000, 0x0800, 0x0866, 0x0000, /* 20 */ - 0x0000, 0x0000, 0xFFFF, 0xFFFF, 0xFFFF, 0xFFFF, 0xFFFF, 0xFFFF, /* 28 */ - 0xFFFF, 0xFFFF, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /* 30 */ - 0x0000, 0x0000, 0x000F, 0x6A62, 0x1988, 0x3100, 0x3100, 0x3100, /* 38 */ - 0x3100, 0xA708, 0x2430, 0x0830, 0x1030, 0x4610, 0xFF00, 0xFF00, /* 40 */ - 0x0060, 0x1000, 0x0400, 0x0040, 0x00F0, 0x0155, 0x1100, 0xA02A, /* 48 */ - 0x06FA, 0x0080, 0xB008, 0xE3ED, 0x5002, 0xB592, 0x7A80, 0x0001, /* 50 */ - 0x020A, 0x8820, 0x6014, 0x8054, 0xACAA, 0xFC88, 0x2A02, 0x45CF, /* 58 */ - 0x000F, 0x1817, 0x2860, 0x064F, 0x0000, 0x0204, 0x1800, 0x6000, /* 60 */ - 0x810F, 0x4F23, 0x4000, 0x4498, 0x0850, 0x0000, 0x000E, 0x1002, /* 68 */ - 0x9D3A, 0x3009, 0xD066, 0x0491, 0x0001, 0x6AB0, 0x0399, 0x3780, /* 70 */ - 0x0040, 0x5AC0, 0x4A80, 0x0000, 0x01DF, 0x0000, 0x0007, 0x0000, /* 78 */ - 0x2D54, 0x00A1, 0x4000, 0x0100, 0xA20A, 0x0000, 0x0000, 0x0000, /* 80 */ - 0x0000, 0x0000, 0x0000, 0x7400, 0x0E81, 0x1000, 0x1242, 0x0210, /* 88 */ - 0x80DF, 0x0F1F, 0x2F3F, 0x4F5F, 0x6F7F, 0x0F1F, 0x2F3F, 0x4F5F, /* 90 */ - 0x6F7F, 0x4BAD, 0x0000, 0x0000, 0x0800, 0x0000, 0x2400, 0xB651, /* 98 */ - 0xC9E0, 0x4247, 0x0A24, 0x0000, 0xAF19, 0x1004, 0x0000, 0x0000, /* A0 */ - 0x0000, 0x0013, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /* A8 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /* B0 */ - 0x0000, 0x0000, 0x0000, 0x0060, 0x0000, 0x0000, 0x0000, 0x0000, /* B8 */ - 0x0000, 0x0000, 0x3010, 0xFA00, 0x0000, 0x0000, 0x0000, 0x0003, /* C0 */ - 0x1618, 0x8200, 0x8000, 0x0400, 0x050F, 0x0000, 0x0000, 0x0000, /* C8 */ - 0x4C93, 0x0000, 0x1000, 0x1120, 0x0010, 0x1242, 0x1242, 0x1E00, /* D0 */ - 0x0000, 0x0000, 0x0000, 0x00F8, 0x0000, 0x0041, 0x0800, 0x0000, /* D8 */ - 0x82A0, 0x572E, 0x2490, 0x14A9, 0x4E00, 0x0000, 0x0803, 0x0541, /* E0 */ - 0x0C15, 0x0000, 0x0000, 0x0400, 0x2626, 0x0000, 0x0000, 0x4200, /* E8 */ - 0x0000, 0xAA55, 0x1020, 0x0000, 0x0000, 0x5010, 0x0000, 0x0000, /* F0 */ - 0x0000, 0x0000, 0x5000, 0x0000, 0x0000, 0x0000, 0x02F2, 0x0000, /* F8 */ - 0x101F, 0xFDC0, 0x4000, 0x8010, 0x0110, 0x0006, 0x0000, 0x0000, /*100 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*108 */ - 0x04CF, 0x0000, 0x04CF, 0x0000, 0x04CF, 0x0000, 0x04C6, 0x0000, /*110 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*118 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*120 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*128 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*130 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*138 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*140 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*148 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*150 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*158 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*160 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*168 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*170 */ - 0x0000, 0x0000, 0x0000, 0x00F0, 0x08A2, 0x3112, 0x0A14, 0x0000, /*178 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*180 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*188 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*190 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*198 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1A0 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1A8 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1B0 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1B8 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1C0 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1C8 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1D0 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1D8 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1E0 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1E8 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, /*1F0 */ - 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000 /*1F8 */ -}; - -/* - * comphy_poll_reg - * - * return: 1 on success, 0 on timeout - */ -static u32 comphy_poll_reg(void *addr, u32 val, u32 mask, u8 op_type) -{ - u32 rval = 0xDEAD, timeout; - - for (timeout = PLL_LOCK_TIMEOUT; timeout > 0; timeout--) { - if (op_type == POLL_16B_REG) - rval = readw(addr); /* 16 bit */ - else - rval = readl(addr) ; /* 32 bit */ - - if ((rval & mask) == val) - return 1; - - udelay(10000); - } - - debug("Time out waiting (%p = %#010x)\n", addr, rval); - return 0; -} - -/* - * comphy_pcie_power_up - * - * return: 1 if PLL locked (OK), 0 otherwise (FAIL) - */ -static int comphy_pcie_power_up(u32 speed, u32 invert) -{ - int ret; - - debug_enter(); - - /* - * 1. Enable max PLL. - */ - reg_set16(phy_addr(PCIE, LANE_CFG1), bf_use_max_pll_rate, 0); - - /* - * 2. Select 20 bit SERDES interface. - */ - reg_set16(phy_addr(PCIE, GLOB_CLK_SRC_LO), bf_cfg_sel_20b, 0); - - /* - * 3. Force to use reg setting for PCIe mode - */ - reg_set16(phy_addr(PCIE, MISC_REG1), bf_sel_bits_pcie_force, 0); - - /* - * 4. Change RX wait - */ - reg_set16(phy_addr(PCIE, PWR_MGM_TIM1), 0x10C, 0xFFFF); - - /* - * 5. Enable idle sync - */ - reg_set16(phy_addr(PCIE, UNIT_CTRL), 0x60 | rb_idle_sync_en, 0xFFFF); - - /* - * 6. Enable the output of 100M/125M/500M clock - */ - reg_set16(phy_addr(PCIE, MISC_REG0), - 0xA00D | rb_clk500m_en | rb_clk100m_125m_en, 0xFFFF); - - /* - * 7. Enable TX - */ - reg_set(PCIE_REF_CLK_ADDR, 0x1342, 0xFFFFFFFF); - - /* - * 8. Check crystal jumper setting and program the Power and PLL - * Control accordingly - */ - if (get_ref_clk() == 40) { - /* 40 MHz */ - reg_set16(phy_addr(PCIE, PWR_PLL_CTRL), 0xFC63, 0xFFFF); - } else { - /* 25 MHz */ - reg_set16(phy_addr(PCIE, PWR_PLL_CTRL), 0xFC62, 0xFFFF); - } - - /* - * 9. Override Speed_PLL value and use MAC PLL - */ - reg_set16(phy_addr(PCIE, KVCO_CAL_CTRL), 0x0040 | rb_use_max_pll_rate, - 0xFFFF); - - /* - * 10. Check the Polarity invert bit - */ - if (invert & PHY_POLARITY_TXD_INVERT) - reg_set16(phy_addr(PCIE, SYNC_PATTERN), phy_txd_inv, 0); - - if (invert & PHY_POLARITY_RXD_INVERT) - reg_set16(phy_addr(PCIE, SYNC_PATTERN), phy_rxd_inv, 0); - - /* - * 11. Release SW reset - */ - reg_set16(phy_addr(PCIE, GLOB_PHY_CTRL0), - rb_mode_core_clk_freq_sel | rb_mode_pipe_width_32, - bf_soft_rst | bf_mode_refdiv); - - /* Wait for > 55 us to allow PCLK be enabled */ - udelay(PLL_SET_DELAY_US); - - /* Assert PCLK enabled */ - ret = comphy_poll_reg(phy_addr(PCIE, LANE_STAT1), /* address */ - rb_txdclk_pclk_en, /* value */ - rb_txdclk_pclk_en, /* mask */ - POLL_16B_REG); /* 16bit */ - if (!ret) - printf("Failed to lock PCIe PLL\n"); - - debug_exit(); - - /* Return the status of the PLL */ - return ret; -} - -/* - * reg_set_indirect - * - * return: void - */ -static void reg_set_indirect(u32 reg, u16 data, u16 mask) -{ - reg_set(rh_vsreg_addr, reg, 0xFFFFFFFF); - reg_set(rh_vsreg_data, data, mask); -} - -/* - * comphy_sata_power_up - * - * return: 1 if PLL locked (OK), 0 otherwise (FAIL) - */ -static int comphy_sata_power_up(void) -{ - int ret; - - debug_enter(); - - /* - * 0. Swap SATA TX lines - */ - reg_set_indirect(vphy_sync_pattern_reg, bs_txd_inv, bs_txd_inv); - - /* - * 1. Select 40-bit data width width - */ - reg_set_indirect(vphy_loopback_reg0, 0x800, bs_phyintf_40bit); - - /* - * 2. Select reference clock and PHY mode (SATA) - */ - if (get_ref_clk() == 40) { - /* 40 MHz */ - reg_set_indirect(vphy_power_reg0, 0x3, 0x00FF); - } else { - /* 20 MHz */ - reg_set_indirect(vphy_power_reg0, 0x1, 0x00FF); - } - - /* - * 3. Use maximum PLL rate (no power save) - */ - reg_set_indirect(vphy_calctl_reg, bs_max_pll_rate, bs_max_pll_rate); - - /* - * 4. Reset reserved bit (??) - */ - reg_set_indirect(vphy_reserve_reg, 0, bs_phyctrl_frm_pin); - - /* - * 5. Set vendor-specific configuration (??) - */ - reg_set(rh_vs0_a, vsata_ctrl_reg, 0xFFFFFFFF); - reg_set(rh_vs0_d, bs_phy_pu_pll, bs_phy_pu_pll); - - /* Wait for > 55 us to allow PLL be enabled */ - udelay(PLL_SET_DELAY_US); - - /* Assert SATA PLL enabled */ - reg_set(rh_vsreg_addr, vphy_loopback_reg0, 0xFFFFFFFF); - ret = comphy_poll_reg(rh_vsreg_data, /* address */ - bs_pll_ready_tx, /* value */ - bs_pll_ready_tx, /* mask */ - POLL_32B_REG); /* 32bit */ - if (!ret) - printf("Failed to lock SATA PLL\n"); - - debug_exit(); - - return ret; -} - -/* - * usb3_reg_set16 - * - * return: void - */ -static void usb3_reg_set16(u32 reg, u16 data, u16 mask, u32 lane) -{ - /* - * When Lane 2 PHY is for USB3, access the PHY registers - * through indirect Address and Data registers INDIR_ACC_PHY_ADDR - * (RD00E0178h [31:0]) and INDIR_ACC_PHY_DATA (RD00E017Ch [31:0]) - * within the SATA Host Controller registers, Lane 2 base register - * offset is 0x200 - */ - - if (lane == 2) - reg_set_indirect(USB3PHY_LANE2_REG_BASE_OFFSET + reg, data, - mask); - else - reg_set16(phy_addr(USB3, reg), data, mask); -} - -/* - * comphy_usb3_power_up - * - * return: 1 if PLL locked (OK), 0 otherwise (FAIL) - */ -static int comphy_usb3_power_up(u32 lane, u32 type, u32 speed, u32 invert) -{ - int ret; - - debug_enter(); - - /* - * 1. Power up OTG module - */ - reg_set(USB2_PHY_OTG_CTRL_ADDR, rb_pu_otg, 0); - - /* - * 2. Set counter for 100us pulse in USB3 Host and Device - * restore default burst size limit (Reference Clock 31:24) - */ - reg_set(USB3_CTRPUL_VAL_REG, 0x8 << 24, rb_usb3_ctr_100ns); - - - /* 0xd005c300 = 0x1001 */ - /* set PRD_TXDEEMPH (3.5db de-emph) */ - usb3_reg_set16(LANE_CFG0, 0x1, 0xFF, lane); - - /* - * Set BIT0: enable transmitter in high impedance mode - * Set BIT[3:4]: delay 2 clock cycles for HiZ off latency - * Set BIT6: Tx detect Rx at HiZ mode - * Unset BIT15: set to 0 to set USB3 De-emphasize level to -3.5db - * together with bit 0 of COMPHY_REG_LANE_CFG0_ADDR - * register - */ - usb3_reg_set16(LANE_CFG1, - tx_det_rx_mode | gen2_tx_data_dly_deft - | tx_elec_idle_mode_en, - prd_txdeemph1_mask | tx_det_rx_mode - | gen2_tx_data_dly_mask | tx_elec_idle_mode_en, lane); - - /* 0xd005c310 = 0x93: set Spread Spectrum Clock Enabled */ - usb3_reg_set16(LANE_CFG4, bf_spread_spectrum_clock_en, 0x80, lane); - - /* - * set Override Margining Controls From the MAC: Use margining signals - * from lane configuration - */ - usb3_reg_set16(TEST_MODE_CTRL, rb_mode_margin_override, 0xFFFF, lane); - - /* set Lane-to-Lane Bundle Clock Sampling Period = per PCLK cycles */ - /* set Mode Clock Source = PCLK is generated from REFCLK */ - usb3_reg_set16(GLOB_CLK_SRC_LO, 0x0, 0xFF, lane); - - /* set G2 Spread Spectrum Clock Amplitude at 4K */ - usb3_reg_set16(GEN2_SETTINGS_2, g2_tx_ssc_amp, 0xF000, lane); - - /* - * unset G3 Spread Spectrum Clock Amplitude & set G3 TX and RX Register - * Master Current Select - */ - usb3_reg_set16(GEN2_SETTINGS_3, 0x0, 0xFFFF, lane); - - /* - * 3. Check crystal jumper setting and program the Power and PLL - * Control accordingly - * 4. Change RX wait - */ - if (get_ref_clk() == 40) { - /* 40 MHz */ - usb3_reg_set16(PWR_PLL_CTRL, 0xFCA3, 0xFFFF, lane); - usb3_reg_set16(PWR_MGM_TIM1, 0x10C, 0xFFFF, lane); - } else { - /* 25 MHz */ - usb3_reg_set16(PWR_PLL_CTRL, 0xFCA2, 0xFFFF, lane); - usb3_reg_set16(PWR_MGM_TIM1, 0x107, 0xFFFF, lane); - } - - /* - * 5. Enable idle sync - */ - usb3_reg_set16(UNIT_CTRL, 0x60 | rb_idle_sync_en, 0xFFFF, lane); - - /* - * 6. Enable the output of 500M clock - */ - usb3_reg_set16(MISC_REG0, 0xA00D | rb_clk500m_en, 0xFFFF, lane); - - /* - * 7. Set 20-bit data width - */ - usb3_reg_set16(DIG_LB_EN, 0x0400, 0xFFFF, lane); - - /* - * 8. Override Speed_PLL value and use MAC PLL - */ - usb3_reg_set16(KVCO_CAL_CTRL, 0x0040 | rb_use_max_pll_rate, 0xFFFF, - lane); - - /* - * 9. Check the Polarity invert bit - */ - if (invert & PHY_POLARITY_TXD_INVERT) - usb3_reg_set16(SYNC_PATTERN, phy_txd_inv, 0, lane); - - if (invert & PHY_POLARITY_RXD_INVERT) - usb3_reg_set16(SYNC_PATTERN, phy_rxd_inv, 0, lane); - - /* - * 10. Set max speed generation to USB3.0 5Gbps - */ - usb3_reg_set16(SYNC_MASK_GEN, 0x0400, 0x0C00, lane); - - /* - * 11. Set capacitor value for FFE gain peaking to 0xF - */ - usb3_reg_set16(GEN3_SETTINGS_3, 0xF, 0xF, lane); - - /* - * 12. Release SW reset - */ - usb3_reg_set16(GLOB_PHY_CTRL0, - rb_mode_core_clk_freq_sel | rb_mode_pipe_width_32 - | 0x20, 0xFFFF, lane); - - /* Wait for > 55 us to allow PCLK be enabled */ - udelay(PLL_SET_DELAY_US); - - /* Assert PCLK enabled */ - if (lane == 2) { - reg_set(rh_vsreg_addr, - LANE_STAT1 + USB3PHY_LANE2_REG_BASE_OFFSET, - 0xFFFFFFFF); - ret = comphy_poll_reg(rh_vsreg_data, /* address */ - rb_txdclk_pclk_en, /* value */ - rb_txdclk_pclk_en, /* mask */ - POLL_32B_REG); /* 32bit */ - } else { - ret = comphy_poll_reg(phy_addr(USB3, LANE_STAT1), /* address */ - rb_txdclk_pclk_en, /* value */ - rb_txdclk_pclk_en, /* mask */ - POLL_16B_REG); /* 16bit */ - } - if (!ret) - printf("Failed to lock USB3 PLL\n"); - - /* - * Set Soft ID for Host mode (Device mode works with Hard ID - * detection) - */ - if (type == PHY_TYPE_USB3_HOST0) { - /* - * set BIT0: set ID_MODE of Host/Device = "Soft ID" (BIT1) - * clear BIT1: set SOFT_ID = Host - * set BIT4: set INT_MODE = ID. Interrupt Mode: enable - * interrupt by ID instead of using both interrupts - * of HOST and Device ORed simultaneously - * INT_MODE=ID in order to avoid unexpected - * behaviour or both interrupts together - */ - reg_set(USB32_CTRL_BASE, - usb32_ctrl_id_mode | usb32_ctrl_int_mode, - usb32_ctrl_id_mode | usb32_ctrl_soft_id | - usb32_ctrl_int_mode); - } - - debug_exit(); - - return ret; -} - -/* - * comphy_usb2_power_up - * - * return: 1 if PLL locked (OK), 0 otherwise (FAIL) - */ -static int comphy_usb2_power_up(u8 usb32) -{ - int ret; - - debug_enter(); - - if (usb32 != 0 && usb32 != 1) { - printf("invalid usb32 value: (%d), should be either 0 or 1\n", - usb32); - debug_exit(); - return 0; - } - - /* - * 0. Setup PLL. 40MHz clock uses defaults. - * See "PLL Settings for Typical REFCLK" table - */ - if (get_ref_clk() == 25) { - reg_set(USB2_PHY_BASE(usb32), 5 | (96 << 16), - 0x3F | (0xFF << 16) | (0x3 << 28)); - } - - /* - * 1. PHY pull up and disable USB2 suspend - */ - reg_set(USB2_PHY_CTRL_ADDR(usb32), - RB_USB2PHY_SUSPM(usb32) | RB_USB2PHY_PU(usb32), 0); - - if (usb32 != 0) { - /* - * 2. Power up OTG module - */ - reg_set(USB2_PHY_OTG_CTRL_ADDR, rb_pu_otg, 0); - - /* - * 3. Configure PHY charger detection - */ - reg_set(USB2_PHY_CHRGR_DET_ADDR, 0, - rb_cdp_en | rb_dcp_en | rb_pd_en | rb_cdp_dm_auto | - rb_enswitch_dp | rb_enswitch_dm | rb_pu_chrg_dtc); - } - - /* Assert PLL calibration done */ - ret = comphy_poll_reg(USB2_PHY_CAL_CTRL_ADDR(usb32), - rb_usb2phy_pllcal_done, /* value */ - rb_usb2phy_pllcal_done, /* mask */ - POLL_32B_REG); /* 32bit */ - if (!ret) - printf("Failed to end USB2 PLL calibration\n"); - - /* Assert impedance calibration done */ - ret = comphy_poll_reg(USB2_PHY_CAL_CTRL_ADDR(usb32), - rb_usb2phy_impcal_done, /* value */ - rb_usb2phy_impcal_done, /* mask */ - POLL_32B_REG); /* 32bit */ - if (!ret) - printf("Failed to end USB2 impedance calibration\n"); - - /* Assert squetch calibration done */ - ret = comphy_poll_reg(USB2_PHY_RX_CHAN_CTRL1_ADDR(usb32), - rb_usb2phy_sqcal_done, /* value */ - rb_usb2phy_sqcal_done, /* mask */ - POLL_32B_REG); /* 32bit */ - if (!ret) - printf("Failed to end USB2 unknown calibration\n"); - - /* Assert PLL is ready */ - ret = comphy_poll_reg(USB2_PHY_PLL_CTRL0_ADDR(usb32), - rb_usb2phy_pll_ready, /* value */ - rb_usb2phy_pll_ready, /* mask */ - POLL_32B_REG); /* 32bit */ - - if (!ret) - printf("Failed to lock USB2 PLL\n"); - - debug_exit(); - - return ret; -} - -/* - * comphy_emmc_power_up - * - * return: 1 if PLL locked (OK), 0 otherwise (FAIL) - */ -static int comphy_emmc_power_up(void) -{ - debug_enter(); - - /* - * 1. Bus power ON, Bus voltage 1.8V - */ - reg_set(SDIO_HOST_CTRL1_ADDR, 0xB00, 0xF00); - - /* - * 2. Set FIFO parameters - */ - reg_set(SDIO_SDHC_FIFO_ADDR, 0x315, 0xFFFFFFFF); - - /* - * 3. Set Capabilities 1_2 - */ - reg_set(SDIO_CAP_12_ADDR, 0x25FAC8B2, 0xFFFFFFFF); - - /* - * 4. Set Endian - */ - reg_set(SDIO_ENDIAN_ADDR, 0x00c00000, 0); - - /* - * 4. Init PHY - */ - reg_set(SDIO_PHY_TIMING_ADDR, 0x80000000, 0x80000000); - reg_set(SDIO_PHY_PAD_CTRL0_ADDR, 0x50000000, 0xF0000000); - - /* - * 5. DLL reset - */ - reg_set(SDIO_DLL_RST_ADDR, 0xFFFEFFFF, 0); - reg_set(SDIO_DLL_RST_ADDR, 0x00010000, 0); - - debug_exit(); - - return 1; -} - -/* - * comphy_sgmii_power_up - * - * return: - */ -static void comphy_sgmii_phy_init(u32 lane, u32 speed) -{ - const int fix_arr_sz = ARRAY_SIZE(sgmii_phy_init_fix); - int addr, fix_idx; - u16 val; - - fix_idx = 0; - for (addr = 0; addr < 512; addr++) { - /* - * All PHY register values are defined in full for 3.125Gbps - * SERDES speed. The values required for 1.25 Gbps are almost - * the same and only few registers should be "fixed" in - * comparison to 3.125 Gbps values. These register values are - * stored in "sgmii_phy_init_fix" array. - */ - if ((speed != PHY_SPEED_1_25G) && - (sgmii_phy_init_fix[fix_idx].addr == addr)) { - /* Use new value */ - val = sgmii_phy_init_fix[fix_idx].value; - if (fix_idx < fix_arr_sz) - fix_idx++; - } else { - val = sgmii_phy_init[addr]; - } - - reg_set16(sgmiiphy_addr(lane, addr), val, 0xFFFF); - } -} - -/* - * comphy_sgmii_power_up - * - * return: 1 if PLL locked (OK), 0 otherwise (FAIL) - */ -static int comphy_sgmii_power_up(u32 lane, u32 speed, u32 invert) -{ - int ret; - u32 saved_selector; - - debug_enter(); - - /* - * 1. Configure PHY to SATA/SAS mode by setting pin PIN_PIPE_SEL=0 - */ - saved_selector = readl(COMPHY_SEL_ADDR); - reg_set(COMPHY_SEL_ADDR, 0, 0xFFFFFFFF); - - /* - * 2. Reset PHY by setting PHY input port PIN_RESET=1. - * 3. Set PHY input port PIN_TX_IDLE=1, PIN_PU_IVREF=1 to keep - * PHY TXP/TXN output to idle state during PHY initialization - * 4. Set PHY input port PIN_PU_PLL=0, PIN_PU_RX=0, PIN_PU_TX=0. - */ - reg_set(COMPHY_PHY_CFG1_ADDR(lane), - rb_pin_reset_comphy | rb_pin_tx_idle | rb_pin_pu_iveref, - rb_pin_reset_core | rb_pin_pu_pll | - rb_pin_pu_rx | rb_pin_pu_tx); - - /* - * 5. Release reset to the PHY by setting PIN_RESET=0. - */ - reg_set(COMPHY_PHY_CFG1_ADDR(lane), 0, rb_pin_reset_comphy); - - /* - * 7. Set PIN_PHY_GEN_TX[3:0] and PIN_PHY_GEN_RX[3:0] to decide - * COMPHY bit rate - */ - if (speed == PHY_SPEED_3_125G) { /* 3.125 GHz */ - reg_set(COMPHY_PHY_CFG1_ADDR(lane), - (0x8 << rf_gen_rx_sel_shift) | - (0x8 << rf_gen_tx_sel_shift), - rf_gen_rx_select | rf_gen_tx_select); - - } else if (speed == PHY_SPEED_1_25G) { /* 1.25 GHz */ - reg_set(COMPHY_PHY_CFG1_ADDR(lane), - (0x6 << rf_gen_rx_sel_shift) | - (0x6 << rf_gen_tx_sel_shift), - rf_gen_rx_select | rf_gen_tx_select); - } else { - printf("Unsupported COMPHY speed!\n"); - return 0; - } - - /* - * 8. Wait 1mS for bandgap and reference clocks to stabilize; - * then start SW programming. - */ - mdelay(10); - - /* 9. Program COMPHY register PHY_MODE */ - reg_set16(sgmiiphy_addr(lane, PWR_PLL_CTRL), - PHY_MODE_SGMII << rf_phy_mode_shift, rf_phy_mode_mask); - - /* - * 10. Set COMPHY register REFCLK_SEL to select the correct REFCLK - * source - */ - reg_set16(sgmiiphy_addr(lane, MISC_REG0), 0, rb_ref_clk_sel); - - /* - * 11. Set correct reference clock frequency in COMPHY register - * REF_FREF_SEL. - */ - if (get_ref_clk() == 40) { - reg_set16(sgmiiphy_addr(lane, PWR_PLL_CTRL), - 0x4 << rf_ref_freq_sel_shift, rf_ref_freq_sel_mask); - } else { - /* 25MHz */ - reg_set16(sgmiiphy_addr(lane, PWR_PLL_CTRL), - 0x1 << rf_ref_freq_sel_shift, rf_ref_freq_sel_mask); - } - - /* 12. Program COMPHY register PHY_GEN_MAX[1:0] */ - /* - * This step is mentioned in the flow received from verification team. - * However the PHY_GEN_MAX value is only meaningful for other - * interfaces (not SGMII). For instance, it selects SATA speed - * 1.5/3/6 Gbps or PCIe speed 2.5/5 Gbps - */ - - /* - * 13. Program COMPHY register SEL_BITS to set correct parallel data - * bus width - */ - /* 10bit */ - reg_set16(sgmiiphy_addr(lane, DIG_LB_EN), 0, rf_data_width_mask); - - /* - * 14. As long as DFE function needs to be enabled in any mode, - * COMPHY register DFE_UPDATE_EN[5:0] shall be programmed to 0x3F - * for real chip during COMPHY power on. - */ - /* - * The step 14 exists (and empty) in the original initialization flow - * obtained from the verification team. According to the functional - * specification DFE_UPDATE_EN already has the default value 0x3F - */ - - /* - * 15. Program COMPHY GEN registers. - * These registers should be programmed based on the lab testing - * result to achieve optimal performance. Please contact the CEA - * group to get the related GEN table during real chip bring-up. - * We only requred to run though the entire registers programming - * flow defined by "comphy_sgmii_phy_init" when the REF clock is - * 40 MHz. For REF clock 25 MHz the default values stored in PHY - * registers are OK. - */ - debug("Running C-DPI phy init %s mode\n", - speed == PHY_SPEED_3_125G ? "2G5" : "1G"); - if (get_ref_clk() == 40) - comphy_sgmii_phy_init(lane, speed); - - /* - * 16. [Simulation Only] should not be used for real chip. - * By pass power up calibration by programming EXT_FORCE_CAL_DONE - * (R02h[9]) to 1 to shorten COMPHY simulation time. - */ - /* - * 17. [Simulation Only: should not be used for real chip] - * Program COMPHY register FAST_DFE_TIMER_EN=1 to shorten RX - * training simulation time. - */ - - /* - * 18. Check the PHY Polarity invert bit - */ - if (invert & PHY_POLARITY_TXD_INVERT) - reg_set16(sgmiiphy_addr(lane, SYNC_PATTERN), phy_txd_inv, 0); - - if (invert & PHY_POLARITY_RXD_INVERT) - reg_set16(sgmiiphy_addr(lane, SYNC_PATTERN), phy_rxd_inv, 0); - - /* - * 19. Set PHY input ports PIN_PU_PLL, PIN_PU_TX and PIN_PU_RX to 1 - * to start PHY power up sequence. All the PHY register - * programming should be done before PIN_PU_PLL=1. There should be - * no register programming for normal PHY operation from this point. - */ - reg_set(COMPHY_PHY_CFG1_ADDR(lane), - rb_pin_pu_pll | rb_pin_pu_rx | rb_pin_pu_tx, - rb_pin_pu_pll | rb_pin_pu_rx | rb_pin_pu_tx); - - /* - * 20. Wait for PHY power up sequence to finish by checking output ports - * PIN_PLL_READY_TX=1 and PIN_PLL_READY_RX=1. - */ - ret = comphy_poll_reg(COMPHY_PHY_STAT1_ADDR(lane), /* address */ - rb_pll_ready_tx | rb_pll_ready_rx, /* value */ - rb_pll_ready_tx | rb_pll_ready_rx, /* mask */ - POLL_32B_REG); /* 32bit */ - if (!ret) - printf("Failed to lock PLL for SGMII PHY %d\n", lane); - - /* - * 21. Set COMPHY input port PIN_TX_IDLE=0 - */ - reg_set(COMPHY_PHY_CFG1_ADDR(lane), 0x0, rb_pin_tx_idle); - - /* - * 22. After valid data appear on PIN_RXDATA bus, set PIN_RX_INIT=1. - * to start RX initialization. PIN_RX_INIT_DONE will be cleared to - * 0 by the PHY. After RX initialization is done, PIN_RX_INIT_DONE - * will be set to 1 by COMPHY. Set PIN_RX_INIT=0 after - * PIN_RX_INIT_DONE= 1. - * Please refer to RX initialization part for details. - */ - reg_set(COMPHY_PHY_CFG1_ADDR(lane), rb_phy_rx_init, 0x0); - - ret = comphy_poll_reg(COMPHY_PHY_STAT1_ADDR(lane), /* address */ - rb_rx_init_done, /* value */ - rb_rx_init_done, /* mask */ - POLL_32B_REG); /* 32bit */ - if (!ret) - printf("Failed to init RX of SGMII PHY %d\n", lane); - - /* - * Restore saved selector. - */ - reg_set(COMPHY_SEL_ADDR, saved_selector, 0xFFFFFFFF); - - debug_exit(); - - return ret; -} - -void comphy_dedicated_phys_init(void) -{ - int node, usb32, ret = 1; - const void *blob = gd->fdt_blob; - - debug_enter(); - - for (usb32 = 0; usb32 <= 1; usb32++) { - /* - * There are 2 UTMI PHYs in this SOC. - * One is independendent and one is paired with USB3 port (OTG) - */ - if (usb32 == 0) { - node = fdt_node_offset_by_compatible( - blob, -1, "marvell,armada3700-ehci"); - } else { - node = fdt_node_offset_by_compatible( - blob, -1, "marvell,armada3700-xhci"); - } - - if (node > 0) { - if (fdtdec_get_is_enabled(blob, node)) { - ret = comphy_usb2_power_up(usb32); - if (!ret) - printf("Failed to initialize UTMI PHY\n"); - else - debug("UTMI PHY init succeed\n"); - } else { - debug("USB%d node is disabled\n", - usb32 == 0 ? 2 : 3); - } - } else { - debug("No USB%d node in DT\n", usb32 == 0 ? 2 : 3); - } - } - - node = fdt_node_offset_by_compatible(blob, -1, - "marvell,armada-3700-ahci"); - if (node > 0) { - if (fdtdec_get_is_enabled(blob, node)) { - ret = comphy_sata_power_up(); - if (!ret) - printf("Failed to initialize SATA PHY\n"); - else - debug("SATA PHY init succeed\n"); - } else { - debug("SATA node is disabled\n"); - } - } else { - debug("No SATA node in DT\n"); - } - - node = fdt_node_offset_by_compatible(blob, -1, - "marvell,armada-8k-sdhci"); - if (node <= 0) { - node = fdt_node_offset_by_compatible( - blob, -1, "marvell,armada-3700-sdhci"); - } - - if (node > 0) { - if (fdtdec_get_is_enabled(blob, node)) { - ret = comphy_emmc_power_up(); - if (!ret) - printf("Failed to initialize SDIO/eMMC PHY\n"); - else - debug("SDIO/eMMC PHY init succeed\n"); - } else { - debug("SDIO/eMMC node is disabled\n"); - } - } else { - debug("No SDIO/eMMC node in DT\n"); - } - - debug_exit(); -} - -int comphy_a3700_init(struct chip_serdes_phy_config *chip_cfg, - struct comphy_map *serdes_map) -{ - struct comphy_map *comphy_map; - u32 comphy_max_count = chip_cfg->comphy_lanes_count; - u32 lane, ret = 0; - - debug_enter(); - - /* Initialize PHY mux */ - chip_cfg->mux_data = a3700_comphy_mux_data; - comphy_mux_init(chip_cfg, serdes_map, COMPHY_SEL_ADDR); - - for (lane = 0, comphy_map = serdes_map; lane < comphy_max_count; - lane++, comphy_map++) { - debug("Initialize serdes number %d\n", lane); - debug("Serdes type = 0x%x invert=%d\n", - comphy_map->type, comphy_map->invert); - - switch (comphy_map->type) { - case PHY_TYPE_UNCONNECTED: - continue; - break; - - case PHY_TYPE_PEX0: - ret = comphy_pcie_power_up(comphy_map->speed, - comphy_map->invert); - break; - - case PHY_TYPE_USB3_HOST0: - case PHY_TYPE_USB3_DEVICE: - ret = comphy_usb3_power_up(lane, - comphy_map->type, - comphy_map->speed, - comphy_map->invert); - break; - - case PHY_TYPE_SGMII0: - case PHY_TYPE_SGMII1: - ret = comphy_sgmii_power_up(lane, comphy_map->speed, - comphy_map->invert); - break; - - default: - debug("Unknown SerDes type, skip initialize SerDes %d\n", - lane); - ret = 1; - break; - } - if (!ret) - printf("PLL is not locked - Failed to initialize lane %d\n", - lane); - } - - debug_exit(); - return ret; -} diff --git a/drivers/phy/marvell/comphy_a3700.h b/drivers/phy/marvell/comphy_a3700.h deleted file mode 100644 index b0941ffb37..0000000000 --- a/drivers/phy/marvell/comphy_a3700.h +++ /dev/null @@ -1,264 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) 2015-2016 Marvell International Ltd. - */ - -#ifndef _COMPHY_A3700_H_ -#define _COMPHY_A3700_H_ - -#include "comphy_core.h" -#include "comphy_hpipe.h" - -#define MVEBU_REG(offs) \ - ((void __iomem *)(ulong)MVEBU_REGISTER(offs)) - -#define DEFAULT_REFCLK_MHZ 25 -#define PLL_SET_DELAY_US 600 -#define PLL_LOCK_TIMEOUT 1000 -#define POLL_16B_REG 1 -#define POLL_32B_REG 0 - -/* - * COMPHY SB definitions - */ -#define COMPHY_SEL_ADDR MVEBU_REG(0x0183FC) - -#define COMPHY_PHY_CFG1_ADDR(lane) MVEBU_REG(0x018300 + (1 - lane) * 0x28) -#define rb_pin_pu_iveref BIT(1) -#define rb_pin_reset_core BIT(11) -#define rb_pin_reset_comphy BIT(12) -#define rb_pin_pu_pll BIT(16) -#define rb_pin_pu_rx BIT(17) -#define rb_pin_pu_tx BIT(18) -#define rb_pin_tx_idle BIT(19) -#define rf_gen_rx_sel_shift 22 -#define rf_gen_rx_select (0x0F << rf_gen_rx_sel_shift) -#define rf_gen_tx_sel_shift 26 -#define rf_gen_tx_select (0x0F << rf_gen_tx_sel_shift) -#define rb_phy_rx_init BIT(30) - -#define COMPHY_PHY_STAT1_ADDR(lane) MVEBU_REG(0x018318 + (1 - lane) * 0x28) -#define rb_rx_init_done BIT(0) -#define rb_pll_ready_rx BIT(2) -#define rb_pll_ready_tx BIT(3) - -/* - * PCIe/USB/SGMII definitions - */ -#define PCIE_BASE MVEBU_REG(0x070000) -#define PCIETOP_BASE MVEBU_REG(0x080000) -#define PCIE_RAMBASE MVEBU_REG(0x08C000) -#define PCIEPHY_BASE MVEBU_REG(0x01F000) -#define PCIEPHY_SHFT 2 - -#define USB32_BASE MVEBU_REG(0x050000) /* usb3 device */ -#define USB32H_BASE MVEBU_REG(0x058000) /* usb3 host */ -#define USB3PHY_BASE MVEBU_REG(0x05C000) -#define USB2PHY_BASE MVEBU_REG(0x05D000) -#define USB2PHY2_BASE MVEBU_REG(0x05F000) -#define USB32_CTRL_BASE MVEBU_REG(0x05D800) -#define USB3PHY_SHFT 2 -#define USB3PHY_LANE2_REG_BASE_OFFSET 0x200 - -static inline void __iomem *sgmiiphy_addr(u32 lane, u32 addr) -{ - addr = (addr & 0x00007FF) * 2; - if (lane == 1) - return PCIEPHY_BASE + addr; - else - return USB3PHY_BASE + addr; -} - -/* units */ -enum phy_unit { - PCIE = 1, - USB3 = 2, -}; - -static inline void __iomem *phy_addr(enum phy_unit unit, u32 addr) -{ - if (unit == PCIE) - return PCIEPHY_BASE + addr * PCIEPHY_SHFT; - else - return USB3PHY_BASE + addr * USB3PHY_SHFT; -} - -/* bit definition for USB32_CTRL_BASE (USB32 Control Mode) */ -#define usb32_ctrl_id_mode BIT(0) -#define usb32_ctrl_soft_id BIT(1) -#define usb32_ctrl_int_mode BIT(4) - -#define PWR_PLL_CTRL 0x01 -#define rf_phy_mode_shift 5 -#define rf_phy_mode_mask (0x7 << rf_phy_mode_shift) -#define rf_ref_freq_sel_shift 0 -#define rf_ref_freq_sel_mask (0x1F << rf_ref_freq_sel_shift) -#define PHY_MODE_SGMII 0x4 - -#define KVCO_CAL_CTRL 0x02 -#define rb_use_max_pll_rate BIT(12) -#define rb_force_calibration_done BIT(9) - -#define DIG_LB_EN 0x23 -#define rf_data_width_shift 10 -#define rf_data_width_mask (0x3 << rf_data_width_shift) - -#define SYNC_PATTERN 0x24 -#define phy_txd_inv BIT(10) -#define phy_rxd_inv BIT(11) - -#define SYNC_MASK_GEN 0x25 -#define rb_idle_sync_en BIT(12) - -#define UNIT_CTRL 0x48 - -#define GEN2_SETTINGS_2 0x3e -#define g2_tx_ssc_amp BIT(14) - -#define GEN2_SETTINGS_3 0x3f - -#define GEN3_SETTINGS_3 0x112 - -#define MISC_REG0 0x4f -#define rb_clk100m_125m_en BIT(4) -#define rb_clk500m_en BIT(7) -#define rb_ref_clk_sel BIT(10) - -#define UNIT_IFACE_REF_CLK_CTRL 0x51 -#define rb_ref1m_gen_div_force BIT(8) -#define rf_ref1m_gen_div_value_shift 0 -#define rf_ref1m_gen_div_value_mask (0xFF << rf_ref1m_gen_div_value_shift) - -#define UNIT_ERR_CNT_CONST_CTRL 0x6a -#define rb_fast_dfe_enable BIT(13) - -#define MISC_REG1 0x73 -#define bf_sel_bits_pcie_force BIT(15) - -#define LANE_CFG0 0x180 -#define bf_use_max_pll_rate BIT(9) - -#define LANE_CFG1 0x181 -#define bf_use_max_pll_rate BIT(9) -#define prd_txdeemph1_mask BIT(15) -#define tx_det_rx_mode BIT(6) -#define gen2_tx_data_dly_deft (2 << 3) -#define gen2_tx_data_dly_mask (BIT(3) | BIT(4)) -#define tx_elec_idle_mode_en BIT(0) - -#define LANE_CFG4 0x188 -#define bf_spread_spectrum_clock_en BIT(7) - -#define LANE_STAT1 0x183 -#define rb_txdclk_pclk_en BIT(0) - -#define GLOB_PHY_CTRL0 0x1c1 -#define bf_soft_rst BIT(0) -#define bf_mode_refdiv 0x30 -#define rb_mode_core_clk_freq_sel BIT(9) -#define rb_mode_pipe_width_32 BIT(3) - -#define TEST_MODE_CTRL 0x1c2 -#define rb_mode_margin_override BIT(2) - -#define GLOB_CLK_SRC_LO 0x1c3 -#define bf_cfg_sel_20b BIT(15) - -#define PWR_MGM_TIM1 0x1d0 - -#define PCIE_REF_CLK_ADDR (PCIE_BASE + 0x4814) - -#define USB3_CTRPUL_VAL_REG (0x20 + USB32_BASE) -#define USB3H_CTRPUL_VAL_REG (0x3454 + USB32H_BASE) -#define rb_usb3_ctr_100ns 0xff000000 - -#define USB2_OTG_PHY_CTRL_ADDR (0x820 + USB2PHY_BASE) -#define rb_usb2phy_suspm BIT(14) -#define rb_usb2phy_pu BIT(0) - -#define USB2_PHY_OTG_CTRL_ADDR (0x34 + USB2PHY_BASE) -#define rb_pu_otg BIT(4) - -#define USB2_PHY_CHRGR_DET_ADDR (0x38 + USB2PHY_BASE) -#define rb_cdp_en BIT(2) -#define rb_dcp_en BIT(3) -#define rb_pd_en BIT(4) -#define rb_pu_chrg_dtc BIT(5) -#define rb_cdp_dm_auto BIT(7) -#define rb_enswitch_dp BIT(12) -#define rb_enswitch_dm BIT(13) - -#define USB2_CAL_CTRL_ADDR (0x8 + USB2PHY_BASE) -#define rb_usb2phy_pllcal_done BIT(31) -#define rb_usb2phy_impcal_done BIT(23) - -#define USB2_PLL_CTRL0_ADDR (0x0 + USB2PHY_BASE) -#define rb_usb2phy_pll_ready BIT(31) - -#define USB2_RX_CHAN_CTRL1_ADDR (0x18 + USB2PHY_BASE) -#define rb_usb2phy_sqcal_done BIT(31) - -#define USB2_PHY2_CTRL_ADDR (0x804 + USB2PHY2_BASE) -#define rb_usb2phy2_suspm BIT(7) -#define rb_usb2phy2_pu BIT(0) -#define USB2_PHY2_CAL_CTRL_ADDR (0x8 + USB2PHY2_BASE) -#define USB2_PHY2_PLL_CTRL0_ADDR (0x0 + USB2PHY2_BASE) -#define USB2_PHY2_RX_CHAN_CTRL1_ADDR (0x18 + USB2PHY2_BASE) - -#define USB2_PHY_BASE(usb32) (usb32 == 0 ? USB2PHY2_BASE : USB2PHY_BASE) -#define USB2_PHY_CTRL_ADDR(usb32) \ - (usb32 == 0 ? USB2_PHY2_CTRL_ADDR : USB2_OTG_PHY_CTRL_ADDR) -#define RB_USB2PHY_SUSPM(usb32) \ - (usb32 == 0 ? rb_usb2phy2_suspm : rb_usb2phy_suspm) -#define RB_USB2PHY_PU(usb32) \ - (usb32 == 0 ? rb_usb2phy2_pu : rb_usb2phy_pu) -#define USB2_PHY_CAL_CTRL_ADDR(usb32) \ - (usb32 == 0 ? USB2_PHY2_CAL_CTRL_ADDR : USB2_CAL_CTRL_ADDR) -#define USB2_PHY_RX_CHAN_CTRL1_ADDR(usb32) \ - (usb32 == 0 ? USB2_PHY2_RX_CHAN_CTRL1_ADDR : USB2_RX_CHAN_CTRL1_ADDR) -#define USB2_PHY_PLL_CTRL0_ADDR(usb32) \ - (usb32 == 0 ? USB2_PHY2_PLL_CTRL0_ADDR : USB2_PLL_CTRL0_ADDR) - -/* - * SATA definitions - */ -#define AHCI_BASE MVEBU_REG(0xE0000) - -#define rh_vsreg_addr (AHCI_BASE + 0x178) -#define rh_vsreg_data (AHCI_BASE + 0x17C) -#define rh_vs0_a (AHCI_BASE + 0xA0) -#define rh_vs0_d (AHCI_BASE + 0xA4) - -#define vphy_sync_pattern_reg 0x224 -#define bs_txd_inv BIT(10) -#define bs_rxd_inv BIT(11) - -#define vphy_loopback_reg0 0x223 -#define bs_phyintf_40bit 0x0C00 -#define bs_pll_ready_tx 0x10 - -#define vphy_power_reg0 0x201 - -#define vphy_calctl_reg 0x202 -#define bs_max_pll_rate BIT(12) - -#define vphy_reserve_reg 0x0e -#define bs_phyctrl_frm_pin BIT(13) - -#define vsata_ctrl_reg 0x00 -#define bs_phy_pu_pll BIT(6) - -/* - * SDIO/eMMC definitions - */ -#define SDIO_BASE MVEBU_REG(0xD8000) - -#define SDIO_HOST_CTRL1_ADDR (SDIO_BASE + 0x28) -#define SDIO_SDHC_FIFO_ADDR (SDIO_BASE + 0x12C) -#define SDIO_CAP_12_ADDR (SDIO_BASE + 0x40) -#define SDIO_ENDIAN_ADDR (SDIO_BASE + 0x1A4) -#define SDIO_PHY_TIMING_ADDR (SDIO_BASE + 0x170) -#define SDIO_PHY_PAD_CTRL0_ADDR (SDIO_BASE + 0x178) -#define SDIO_DLL_RST_ADDR (SDIO_BASE + 0x148) - -#endif /* _COMPHY_A3700_H_ */ diff --git a/drivers/phy/marvell/comphy_core.c b/drivers/phy/marvell/comphy_core.c index 244beef18d..8138b487fe 100644 --- a/drivers/phy/marvell/comphy_core.c +++ b/drivers/phy/marvell/comphy_core.c @@ -112,9 +112,6 @@ static int comphy_probe(struct udevice *dev) fdtdec_locate_array(blob, node, "mux-lane-order", chip_cfg->comphy_lanes_count); - if (device_is_compatible(dev, "marvell,comphy-armada-3700")) - chip_cfg->ptr_comphy_chip_init = comphy_a3700_init; - if (device_is_compatible(dev, "marvell,comphy-cp110")) chip_cfg->ptr_comphy_chip_init = comphy_cp110_init; diff --git a/drivers/phy/marvell/comphy_core.h b/drivers/phy/marvell/comphy_core.h index 12ab921d24..c5ca06441c 100644 --- a/drivers/phy/marvell/comphy_core.h +++ b/drivers/phy/marvell/comphy_core.h @@ -7,7 +7,7 @@ #define _COMPHY_CORE_H_ #include -#include +#include #if defined(DEBUG) #define debug_enter() printf("----> Enter %s\n", __func__); @@ -70,6 +70,14 @@ #define MAX_LANE_OPTIONS 10 #define MAX_UTMI_PHY_COUNT 3 +struct comphy_map { + u32 type; + u32 speed; + u32 invert; + bool clk_src; + bool end_point; +}; + struct comphy_mux_options { u32 type; u32 mux_value; @@ -132,21 +140,6 @@ static inline void reg_set16(void __iomem *addr, u16 data, u16 mask) } /* SoC specific init functions */ -#ifdef CONFIG_ARMADA_3700 -int comphy_a3700_init(struct chip_serdes_phy_config *ptr_chip_cfg, - struct comphy_map *serdes_map); -#else -static inline int comphy_a3700_init(struct chip_serdes_phy_config *ptr_chip_cfg, - struct comphy_map *serdes_map) -{ - /* - * This function should never be called in this configuration, so - * lets return an error here. - */ - return -1; -} -#endif - #ifdef CONFIG_ARMADA_8K int comphy_cp110_init(struct chip_serdes_phy_config *ptr_chip_cfg, struct comphy_map *serdes_map); diff --git a/include/mvebu/comphy.h b/include/mvebu/comphy.h deleted file mode 100644 index cde7a022af..0000000000 --- a/include/mvebu/comphy.h +++ /dev/null @@ -1,22 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) 2015-2016 Marvell International Ltd. - */ - -#ifndef _MVEBU_COMPHY_H_ -#define _MVEBU_COMPHY_H_ - -#include - -struct comphy_map { - u32 type; - u32 speed; - u32 invert; - bool clk_src; - bool end_point; -}; - -int comphy_update_map(struct comphy_map *serdes_map, int count); - -#endif /* _MVEBU_COMPHY_H_ */ -