From patchwork Thu Apr 9 13:21:41 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Michael Krummsdorf X-Patchwork-Id: 237504 List-Id: U-Boot discussion From: michael.krummsdorf at ew.tq-group.com (Michael Krummsdorf) Date: Thu, 9 Apr 2020 15:21:41 +0200 Subject: [PATCH 6/7] board: tqc: tqma6: hw init code disabled for device model In-Reply-To: <20200409132142.26491-1-michael.krummsdorf@ew.tq-group.com> References: <20200409132142.26491-1-michael.krummsdorf@ew.tq-group.com> Message-ID: <20200409132142.26491-7-michael.krummsdorf@ew.tq-group.com> Keep code for non-dm configuration of baseboard WRU4. It cannot be upgraded to device model as we have no suitable device tree for it. These changes were not run-tested on WRU4, only compile-tested. Signed-off-by: Michael Krummsdorf --- board/tqc/tqma6/tqma6.c | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/board/tqc/tqma6/tqma6.c b/board/tqc/tqma6/tqma6.c index c8ddc2c1f8..675341abdd 100644 --- a/board/tqc/tqma6/tqma6.c +++ b/board/tqc/tqma6/tqma6.c @@ -60,6 +60,7 @@ int dram_init(void) static const uint16_t tqma6_emmc_dsr = 0x0100; +#ifndef CONFIG_DM_MMC /* eMMC on USDHCI3 always present */ static iomux_v3_cfg_t const tqma6_usdhc3_pads[] = { NEW_PAD_CTRL(MX6_PAD_SD3_CLK__SD3_CLK, USDHC_PAD_CTRL), @@ -132,7 +133,9 @@ int board_mmc_init(bd_t *bis) return 0; } +#endif +#ifndef CONFIG_DM_SPI static iomux_v3_cfg_t const tqma6_ecspi1_pads[] = { /* SS1 */ NEW_PAD_CTRL(MX6_PAD_EIM_D19__GPIO3_IO19, SPI_PAD_CTRL), @@ -164,7 +167,9 @@ int board_spi_cs_gpio(unsigned bus, unsigned cs) (cs == CONFIG_SF_DEFAULT_CS)) ? TQMA6_SF_CS_GPIO : -1; } #endif +#endif +#ifdef CONFIG_SYS_I2C static struct i2c_pads_info tqma6_i2c3_pads = { /* I2C3: on board LM75, M24C64, */ .scl = { @@ -194,6 +199,7 @@ static void tqma6_setup_i2c(void) if (ret) printf("setup I2C3 failed: %d\n", ret); } +#endif int board_early_init_f(void) { @@ -205,8 +211,12 @@ int board_init(void) /* address of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; +#ifndef CONFIG_DM_SPI tqma6_iomuxc_spi(); +#endif +#ifdef CONFIG_SYS_I2C tqma6_setup_i2c(); +#endif tqma6_bb_board_init(); @@ -235,6 +245,7 @@ static const char *tqma6_get_boardname(void) }; } +#ifdef CONFIG_POWER /* setup board specific PMIC */ int power_init_board(void) { @@ -251,6 +262,7 @@ int power_init_board(void) return 0; } +#endif int board_late_init(void) {