@@ -27,4 +27,6 @@ enum {
#define MHz 1000000
+char *get_reset_cause(void);
+
#endif /* _ROCKCHIP_CLOCK_H */
@@ -15,6 +15,10 @@ obj-tpl-$(CONFIG_ROCKCHIP_PX30) += px30-board-tpl.o
obj-spl-$(CONFIG_ROCKCHIP_RK3036) += rk3036-board-spl.o
+ifeq ($(CONFIG_ROCKCHIP_RK3288)$(CONFIG_ROCKCHIP_RK3399), y)
+obj-y += cpu-info.o
+endif
+
ifeq ($(CONFIG_SPL_BUILD)$(CONFIG_TPL_BUILD),)
# Always include boot_mode.o, as we bypass it (i.e. turn it off)
@@ -22,7 +26,6 @@ ifeq ($(CONFIG_SPL_BUILD)$(CONFIG_TPL_BUILD),)
# we can have the preprocessor correctly recognise both 0x0 and 0
# meaning "turn it off".
obj-y += boot_mode.o
-obj-$(CONFIG_DISPLAY_CPUINFO) += cpu-info.o
obj-$(CONFIG_ROCKCHIP_COMMON_BOARD) += board.o
obj-$(CONFIG_MISC_INIT_R) += misc.o
endif
@@ -11,7 +11,7 @@
#include <asm/arch-rockchip/hardware.h>
#include <linux/err.h>
-static char *get_reset_cause(void)
+char *get_reset_cause(void)
{
struct rockchip_cru *cru = rockchip_get_cru();
char *cause = NULL;
@@ -39,12 +39,6 @@ static char *get_reset_cause(void)
cause = "unknown reset";
}
- /**
- * reset_reason env is used by rk3288, due to special use case
- * to figure it the boot behavior. so keep this as it is.
- */
- env_set("reset_reason", cause);
-
/*
* Clear glb_rst_st, so we can determine the last reset cause
* for following resets.
@@ -54,12 +48,22 @@ static char *get_reset_cause(void)
return cause;
}
+#ifdef CONFIG_DISPLAY_CPUINFO
int print_cpuinfo(void)
{
+ char *cause = get_reset_cause();
+
printf("SoC: Rockchip %s\n", CONFIG_SYS_SOC);
- printf("Reset cause: %s\n", get_reset_cause());
+ printf("Reset cause: %s\n", cause);
+
+ /**
+ * reset_reason env is used by rk3288, due to special use case
+ * to figure it the boot behavior. so keep this as it is.
+ */
+ env_set("reset_reason", cause);
/* TODO print operating temparature and clock */
return 0;
}
+#endif
reset cause is a generic functionality based on the soc cru registers in rockchip. This can be used for printing the cause of reset in cpuinfo or some other place where reset cause is needed.? Other than cpuinfo, reset cause can also be using during bootcount for checking the specific reset cause and glow the led based on the reset cause. So, let's separate the reset cause code from cpuinfo, and add a check to build it for rk3399, rk3288 since these two soc are supporting reset cause as of now. Signed-off-by: Jagan Teki <jagan at amarulasolutions.com> --- arch/arm/include/asm/arch-rockchip/cru.h | 2 ++ arch/arm/mach-rockchip/Makefile | 5 ++++- arch/arm/mach-rockchip/cpu-info.c | 20 ++++++++++++-------- 3 files changed, 18 insertions(+), 9 deletions(-)