From patchwork Fri Feb 7 16:55:32 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Michael Auchter X-Patchwork-Id: 236051 List-Id: U-Boot discussion From: michael.auchter at ni.com (Michael Auchter) Date: Fri, 7 Feb 2020 10:55:32 -0600 Subject: [PATCH 2/2] dm: i2c-gpio: add support for clock stretching In-Reply-To: <20200207165532.219139-1-michael.auchter@ni.com> References: <20200123223009.213180-1-michael.auchter@ni.com> <20200207165532.219139-1-michael.auchter@ni.com> Message-ID: <20200207165532.219139-2-michael.auchter@ni.com> This adds support for clock stretching to the i2c-gpio driver. This is accomplished by switching the GPIO used for the SCL line to an input when it should be driven high, and polling on the SCL line value until it goes high (indicating that the I2C slave is no longer pulling it low). This is enabled by default; for gpios which cannot be configured as inputs, the i2c-gpio,scl-output-only property can be used to fall back to the previous behavior. Signed-off-by: Michael Auchter Cc: Heiko Schocher Reviewed-by: Heiko Schocher --- doc/device-tree-bindings/i2c/i2c-gpio.txt | 2 ++ drivers/i2c/i2c-gpio.c | 23 ++++++++++++++++++++++- 2 files changed, 24 insertions(+), 1 deletion(-) diff --git a/doc/device-tree-bindings/i2c/i2c-gpio.txt b/doc/device-tree-bindings/i2c/i2c-gpio.txt index ba56ed5dea..36910d26a9 100644 --- a/doc/device-tree-bindings/i2c/i2c-gpio.txt +++ b/doc/device-tree-bindings/i2c/i2c-gpio.txt @@ -16,6 +16,8 @@ Optional: The resulting transfer speed can be adjusted by setting the delay[us] between gpio-toggle operations. Speed [Hz] = 1000000 / 4 * udelay[us], It not defined, then default is 5us (~50KHz). +* i2c-gpio,scl-output-only; + Set if SCL is an output only Example: diff --git a/drivers/i2c/i2c-gpio.c b/drivers/i2c/i2c-gpio.c index d989449513..8a8d1ff21b 100644 --- a/drivers/i2c/i2c-gpio.c +++ b/drivers/i2c/i2c-gpio.c @@ -56,6 +56,24 @@ static void i2c_gpio_sda_set(struct i2c_gpio_bus *bus, int bit) } static void i2c_gpio_scl_set(struct i2c_gpio_bus *bus, int bit) +{ + struct gpio_desc *scl = &bus->gpios[PIN_SCL]; + int count = 0; + + if (bit) { + dm_gpio_set_dir_flags(scl, GPIOD_IS_IN); + while (!dm_gpio_get_value(scl) && count++ < 100000) + udelay(1); + + if (!dm_gpio_get_value(scl)) + pr_err("timeout waiting on slave to release scl\n"); + } else { + dm_gpio_set_dir_flags(scl, GPIOD_IS_OUT); + } +} + +/* variant for output only gpios which cannot support clock stretching */ +static void i2c_gpio_scl_set_output_only(struct i2c_gpio_bus *bus, int bit) { struct gpio_desc *scl = &bus->gpios[PIN_SCL]; ulong flags = GPIOD_IS_OUT; @@ -313,7 +331,10 @@ static int i2c_gpio_ofdata_to_platdata(struct udevice *dev) bus->get_sda = i2c_gpio_sda_get; bus->set_sda = i2c_gpio_sda_set; - bus->set_scl = i2c_gpio_scl_set; + if (fdtdec_get_bool(blob, node, "i2c-gpio,scl-output-only")) + bus->set_scl = i2c_gpio_scl_set_output_only; + else + bus->set_scl = i2c_gpio_scl_set; return 0; error: