From patchwork Wed Jan 29 03:59:45 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Joel Johnson X-Patchwork-Id: 240435 List-Id: U-Boot discussion From: mrjoel at lixil.net (Joel Johnson) Date: Tue, 28 Jan 2020 20:59:45 -0700 Subject: [PATCH 2/2] arm: mvebu: clearfog: support multiple SATA boot In-Reply-To: <20200129035945.37765-1-mrjoel@lixil.net> References: <20200129035945.37765-1-mrjoel@lixil.net> Message-ID: <20200129035945.37765-2-mrjoel@lixil.net> Enabled distro bootcmd support for additional SATA ports if enabled. Signed-off-by: Joel Johnson --- This patch builds on and requires the separate patch series adding configurable SATA support ("arm: mvebu: clearfog: Add SATA mode flags"). --- include/configs/clearfog.h | 31 ++++++++++++++++++++++++++++--- 1 file changed, 28 insertions(+), 3 deletions(-) diff --git a/include/configs/clearfog.h b/include/configs/clearfog.h index a452f4b009..0bf7e9d950 100644 --- a/include/configs/clearfog.h +++ b/include/configs/clearfog.h @@ -111,15 +111,40 @@ #endif #ifdef CONFIG_SCSI -#define BOOT_TARGET_DEVICES_SCSI(func) func(SCSI, scsi, 0) +#define BOOT_TARGET_DEVICES_SCSI_M2SATA(func) func(SCSI, scsi, 0) + +/* + * Either one or both mPCIe slots may be configured as mSATA interfaces. The + * SCSI bus ids are assigned based on sequence of hardware present, not always + * tied to hardware slot ids. As such, use second SCSI bus if either slot is + * set for SATA, and only use third SCSI bus if both slots are SATA enabled. + */ +#if defined (CONFIG_CLEARFOG_CON2_SATA) || defined (CONFIG_CLEARFOG_CON3_SATA) +#define BOOT_TARGET_DEVICES_SCSI_CLEARFOG2(func) func(SCSI, scsi, 1) +#else +#define BOOT_TARGET_DEVICES_SCSI_CLEARFOG2(func) +#endif + +#if defined (CONFIG_CLEARFOG_CON2_SATA) && defined (CONFIG_CLEARFOG_CON3_SATA) +#define BOOT_TARGET_DEVICES_SCSI_CLEARFOG3(func) func(SCSI, scsi, 2) #else -#define BOOT_TARGET_DEVICES_SCSI(func) +#define BOOT_TARGET_DEVICES_SCSI_CLEARFOG3(func) #endif +#else +#define BOOT_TARGET_DEVICES_SCSI_M2SATA(func) +#endif /* CONFIG_SCSI */ + +/* + * The SCSI buses are attempted in increasing bus order, there is no current + * mechanism to alter the default bus priority order for booting. + */ #define BOOT_TARGET_DEVICES(func) \ BOOT_TARGET_DEVICES_MMC(func) \ BOOT_TARGET_DEVICES_USB(func) \ - BOOT_TARGET_DEVICES_SCSI(func) \ + BOOT_TARGET_DEVICES_SCSI_M2SATA(func) \ + BOOT_TARGET_DEVICES_SCSI_CLEARFOG2(func) \ + BOOT_TARGET_DEVICES_SCSI_CLEARFOG3(func) \ func(PXE, pxe, na) \ func(DHCP, dhcp, na)