@@ -17,6 +17,10 @@
#include <asm/arch/sys_proto.h>
#include <asm/hardware.h>
#include <asm/io.h>
+#include <fs_loader.h>
+#include <fs.h>
+#include <env.h>
+#include <elf.h>
struct ti_sci_handle *get_ti_sci_handle(void)
{
@@ -58,6 +62,74 @@ int early_console_init(void)
#endif
#ifdef CONFIG_SYS_K3_SPL_ATF
+
+void init_env(void)
+{
+#ifdef CONFIG_SPL_ENV_SUPPORT
+ char *part;
+
+ env_init();
+ env_load();
+ switch (spl_boot_device()) {
+ case BOOT_DEVICE_MMC2:
+ part = env_get("bootpart");
+ env_set("storage_interface", "mmc");
+ env_set("fw_dev_part", part);
+ break;
+ case BOOT_DEVICE_SPI:
+ env_set("storage_interface", "ubi");
+ env_set("fw_ubi_mtdpart", "UBI");
+ env_set("fw_ubi_volume", "UBI0");
+ break;
+ default:
+ printf("%s from device %u not supported!\n",
+ __func__, spl_boot_device());
+ return;
+ }
+#endif
+}
+
+#ifdef CONFIG_FS_LOADER
+int load_firmware(char *name_fw, char *name_loadaddr, u32 *loadaddr)
+{
+ struct udevice *fsdev;
+ char *name = NULL;
+ int size = 0;
+
+ *loadaddr = 0;
+#ifdef CONFIG_SPL_ENV_SUPPORT
+ switch (spl_boot_device()) {
+ case BOOT_DEVICE_MMC2:
+ name = env_get(name_fw);
+ *loadaddr = env_get_hex(name_loadaddr, *loadaddr);
+ break;
+ default:
+ printf("Loading rproc fw image from device %u not supported!\n",
+ spl_boot_device());
+ return 0;
+ }
+#endif
+ if (!*loadaddr)
+ return 0;
+
+ if (!uclass_get_device(UCLASS_FS_FIRMWARE_LOADER, 0, &fsdev)) {
+ size = request_firmware_into_buf(fsdev, name, (void *)*loadaddr,
+ 0, 0);
+ }
+
+ return size;
+}
+#else
+int load_firmware(char *name_fw, char *name_loadaddr, u32 *loadaddr)
+{
+ return 0;
+}
+#endif
+
+__weak void start_non_linux_remote_cores(void)
+{
+}
+
void __noreturn jump_to_image_no_args(struct spl_image_info *spl_image)
{
struct ti_sci_handle *ti_sci = get_ti_sci_handle();
@@ -66,15 +138,17 @@ void __noreturn jump_to_image_no_args(struct spl_image_info *spl_image)
/* Release all the exclusive devices held by SPL before starting ATF */
ti_sci->ops.dev_ops.release_exclusive_devices(ti_sci);
+ ret = rproc_init();
+ if (ret)
+ panic("rproc failed to be initialized (%d)\n", ret);
+
+ init_env();
+ start_non_linux_remote_cores();
+
/*
* It is assumed that remoteproc device 1 is the corresponding
* Cortex-A core which runs ATF. Make sure DT reflects the same.
*/
- ret = rproc_dev_init(1);
- if (ret)
- panic("%s: ATF failed to initialize on rproc (%d)\n", __func__,
- ret);
-
ret = rproc_load(1, spl_image->entry_point, 0x200);
if (ret)
panic("%s: ATF failed to load on rproc (%d)\n", __func__, ret);
@@ -24,3 +24,5 @@ void setup_k3_mpu_regions(void);
int early_console_init(void);
void disable_linefill_optimization(void);
void remove_fwl_configs(struct fwl_data *fwl_data, size_t fwl_data_size);
+void start_non_linux_remote_cores(void);
+int load_firmware(char *name_fw, char *name_loadaddr, u32 *loadaddr);
@@ -19,6 +19,7 @@
#include <dm/uclass-internal.h>
#include <dm/pinctrl.h>
#include <mmc.h>
+#include <remoteproc.h>
#ifdef CONFIG_SPL_BUILD
#ifdef CONFIG_K3_LOAD_SYSFW
@@ -326,3 +327,36 @@ void release_resources_for_core_shutdown(void)
}
}
#endif
+
+#ifdef CONFIG_SYS_K3_SPL_ATF
+void start_non_linux_remote_cores(void)
+{
+ int size = 0, ret;
+ u32 loadaddr = 0;
+
+ size = load_firmware("name_mainr5f0_0fw", "addr_mainr5f0_0load",
+ &loadaddr);
+ if (size <= 0)
+ goto err_load;
+
+ /* assuming remoteproc 2 is aliased for the needed remotecore */
+ ret = rproc_load(2, loadaddr, size);
+ if (ret) {
+ printf("Firmware failed to start on rproc (%d)\n", ret);
+ goto err_load;
+ }
+
+ ret = rproc_start(2);
+ if (ret) {
+ printf("Firmware init failed on rproc (%d)\n", ret);
+ goto err_load;
+ }
+
+ printf("Remoteproc 2 started successfully\n");
+
+ return;
+
+err_load:
+ rproc_reset(2);
+}
+#endif