@@ -85,6 +85,16 @@ enum {
LB_RGB_1280X8 = 0x5
};
+#if defined(CONFIG_ROCKCHIP_RK3399)
+enum vop_modes {
+ VOP_MODE_EDP = 0,
+ VOP_MODE_MIPI,
+ VOP_MODE_HDMI,
+ VOP_MODE_MIPI1,
+ VOP_MODE_DP,
+ VOP_MODE_NONE,
+};
+#else
enum vop_modes {
VOP_MODE_EDP = 0,
VOP_MODE_HDMI,
@@ -94,6 +104,7 @@ enum vop_modes {
VOP_MODE_AUTO_DETECT,
VOP_MODE_UNKNOWN,
};
+#endif
/* VOP_VERSION_INFO */
#define M_FPGA_VERSION (0xffff << 16)
@@ -45,8 +45,6 @@ static void rk3399_set_pin_polarity(struct udevice *dev,
V_RK3399_DSP_MIPI_POL(polarity));
break;
- case VOP_MODE_LVDS:
- /* The RK3399 has neither parallel RGB nor LVDS output. */
default:
debug("%s: unsupported output mode %x\n", __func__, mode);
}
@@ -117,10 +117,12 @@ static void rkvop_enable_output(struct udevice *dev, enum vop_modes mode)
V_EDP_OUT_EN(1));
break;
+#if defined(CONFIG_ROCKCHIP_RK3288)
case VOP_MODE_LVDS:
clrsetbits_le32(®s->sys_ctrl, M_ALL_OUT_EN,
V_RGB_OUT_EN(1));
break;
+#endif
case VOP_MODE_MIPI:
clrsetbits_le32(®s->sys_ctrl, M_ALL_OUT_EN,
@@ -312,7 +314,9 @@ static int rk_display_init(struct udevice *dev, ulong fbbase, ofnode ep_node)
/* Set bitwidth for vop display according to vop mode */
switch (vop_id) {
case VOP_MODE_EDP:
+#if defined(CONFIG_ROCKCHIP_RK3288)
case VOP_MODE_LVDS:
+#endif
l2bpp = VIDEO_BPP16;
break;
case VOP_MODE_HDMI:
VOP display endpoint pipeline configuration is differs between rk3288 vs rk3399. These VOP pipeline configuration depends on how the different display interfaces connected in sequence to IN and OUT ports like for, RK3288: vopb_out: port { #address-cells = <1>; #size-cells = <0>; vopb_out_edp: endpoint at 0 { reg = <0>; remote-endpoint = <&edp_in_vopb>; }; vopb_out_hdmi: endpoint at 1 { reg = <1>; remote-endpoint = <&hdmi_in_vopb>; }; vopb_out_lvds: endpoint at 2 { reg = <2>; remote-endpoint = <&lvds_in_vopb>; }; vopb_out_mipi: endpoint at 3 { reg = <3>; remote-endpoint = <&mipi_in_vopb>; }; }; RK3399: vopb_out: port { #address-cells = <1>; #size-cells = <0>; vopb_out_edp: endpoint at 0 { reg = <0>; remote-endpoint = <&edp_in_vopb>; }; vopb_out_mipi: endpoint at 1 { reg = <1>; remote-endpoint = <&mipi_in_vopb>; }; vopb_out_hdmi: endpoint at 2 { reg = <2>; remote-endpoint = <&hdmi_in_vopb>; }; vopb_out_mipi1: endpoint at 3 { reg = <3>; remote-endpoint = <&mipi1_in_vopb>; }; vopb_out_dp: endpoint at 4 { reg = <4>; remote-endpoint = <&dp_in_vopb>; }; }; here, HDMI interface has endpoint 1 in rk3288 and 2 in rk3399. The rockchip vop driver often depends on this determined endpoint number and stored in vop_mode. So based on this vop_mode the bpp and pin polarity would configure on detected display interface. Since, the existing driver using rk3288 vop mode settings enabling the same will result wrong display interface configuration for rk3399. Add the patch for fixing these vop modes for rk3399. Signed-off-by: Jagan Teki <jagan at amarulasolutions.com> --- arch/arm/include/asm/arch-rockchip/vop_rk3288.h | 11 +++++++++++ drivers/video/rockchip/rk3399_vop.c | 2 -- drivers/video/rockchip/rk_vop.c | 4 ++++ 3 files changed, 15 insertions(+), 2 deletions(-)