diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 983e235f4427..b89ed48e9a4e 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -513,8 +513,12 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \
 	sun8i-h2-plus-orangepi-r1.dtb \
 	sun8i-h2-plus-orangepi-zero.dtb \
 	sun8i-h3-bananapi-m2-plus.dtb \
+	sun8i-h3-bananapi-m2-plus-v1.2.dtb \
 	sun8i-h3-beelink-x2.dtb \
+	sun8i-h3-emlid-neutis-n5h3-devboard.dtb \
 	sun8i-h3-libretech-all-h3-cc.dtb \
+	sun8i-h3-mapleboard-mp130.dtb \
+	sun8i-h3-nanopi-duo2.dtb \
 	sun8i-h3-nanopi-m1.dtb \
 	sun8i-h3-nanopi-m1-plus.dtb \
 	sun8i-h3-nanopi-neo.dtb \
@@ -526,7 +530,8 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \
 	sun8i-h3-orangepi-pc-plus.dtb \
 	sun8i-h3-orangepi-plus.dtb \
 	sun8i-h3-orangepi-plus2e.dtb \
-	sun8i-h3-orangepi-zero-plus2.dtb
+	sun8i-h3-orangepi-zero-plus2.dtb \
+	sun8i-h3-rervision-dvk.dtb
 dtb-$(CONFIG_MACH_SUN8I_R40) += \
 	sun8i-r40-bananapi-m2-ultra.dtb \
 	sun8i-v40-bananapi-m2-berry.dtb
@@ -536,6 +541,8 @@ dtb-$(CONFIG_MACH_SUN50I_H5) += \
 	sun50i-h5-bananapi-m2-plus.dtb \
 	sun50i-h5-emlid-neutis-n5-devboard.dtb \
 	sun50i-h5-libretech-all-h3-cc.dtb \
+	sun50i-h5-libretech-all-h3-it.dtb \
+	sun50i-h5-libretech-all-h5-cc.dtb \
 	sun50i-h5-nanopi-neo2.dtb \
 	sun50i-h5-nanopi-neo-plus2.dtb \
 	sun50i-h5-orangepi-zero-plus.dtb \
diff --git a/arch/arm/dts/sun50i-h5-bananapi-m2-plus-v1.2.dts b/arch/arm/dts/sun50i-h5-bananapi-m2-plus-v1.2.dts
new file mode 100644
index 000000000000..2e2b14c0ae75
--- /dev/null
+++ b/arch/arm/dts/sun50i-h5-bananapi-m2-plus-v1.2.dts
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2018 Chen-Yu Tsai <wens at csie.org>
+
+/dts-v1/;
+#include "sun50i-h5.dtsi"
+#include <arm/sunxi-bananapi-m2-plus-v1.2.dtsi>
+
+/ {
+	model = "Banana Pi BPI-M2-Plus v1.2 H5";
+	compatible = "bananapi,bpi-m2-plus-v1.2", "allwinner,sun50i-h5";
+};
diff --git a/arch/arm/dts/sun50i-h5-emlid-neutis-n5-devboard.dts b/arch/arm/dts/sun50i-h5-emlid-neutis-n5-devboard.dts
index 493947c9b14a..076a0b983101 100644
--- a/arch/arm/dts/sun50i-h5-emlid-neutis-n5-devboard.dts
+++ b/arch/arm/dts/sun50i-h5-emlid-neutis-n5-devboard.dts
@@ -1,43 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+// Copyright (C) 2018 Aleksandr Aleksandrov <aleksandr.aleksandrov at emlid.com>
+
 /*
- * Copyright (C) 2018 Aleksandr Aleksandrov <aleksandr.aleksandrov at emlid.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This library is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This library is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
+ * DTS for Emlid Neutis N5 Dev board.
  */
 
 /dts-v1/;
@@ -46,17 +11,9 @@
 
 / {
 	model = "Emlid Neutis N5 Developer board";
-	compatible = "emlid,emlid-neutis-n5-devboard",
-		"emlid,emlid-neutis-n5",
-		"allwinner,sun50i-h5";
-
-	aliases {
-		serial0 = &uart0;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
+	compatible = "emlid,neutis-n5-devboard",
+		     "emlid,neutis-n5",
+		     "allwinner,sun50i-h5";
 
 	connector {
 		compatible = "hdmi-connector";
@@ -69,19 +26,8 @@
 		};
 	};
 
-	reg_usb0_vbus: usb0-vbus {
-		compatible = "regulator-fixed";
-		regulator-name = "usb0-vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		enable-active-high;
-		gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>;   /* PL9 */
-		status = "okay";
-	};
-
 	vdd_cpux: gpio-regulator {
 		compatible = "regulator-gpio";
-		pinctrl-names = "default";
 		regulator-name = "vdd-cpux";
 		regulator-type = "voltage";
 		regulator-boot-on;
@@ -91,54 +37,15 @@
 		regulator-ramp-delay = <50>; /* 4ms */
 		gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
 		gpios-states = <0x1>;
-		states = <1100000 0x0
-			  1300000 0x1>;
+		states = <1100000 0>, <1300000 1>;
 	};
 };
 
-&codec {
-	allwinner,audio-routing =
-		"Line Out", "LINEOUT",
-		"LINEIN", "Line In",
-		"MIC1", "Mic",
-		"MIC2", "Mic",
-		"Mic",  "MBIAS";
-	status = "okay";
-};
-
-&de {
-	status = "okay";
-};
-
-&ehci0 {
-	status = "okay";
+&cpu0 {
+	cpu-supply = <&vdd_cpux>;
 };
 
-&ehci1 {
-	status = "okay";
-};
-
-&ehci2 {
-	status = "okay";
-};
-
-&ehci3 {
-	status = "okay";
-};
-
-&ohci0 {
-	status = "okay";
-};
-
-&ohci1 {
-	status = "okay";
-};
-
-&ohci2 {
-	status = "okay";
-};
-
-&ohci3 {
+&codec {
 	status = "okay";
 };
 
@@ -159,26 +66,6 @@
 	};
 };
 
-&mmc0 {
-	vmmc-supply = <&reg_vcc3v3>;
-	bus-width = <4>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
-	status = "okay";
-};
-
-&uart0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
-	status = "okay";
-};
-
-&usb_otg {
-	dr_mode = "otg";
-	status = "okay";
-};
-
-&usbphy {
-	usb0_id_det-gpios = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
-	usb0_vbus-supply = <&reg_usb0_vbus>;
+&i2c1 {
 	status = "okay";
 };
diff --git a/arch/arm/dts/sun50i-h5-emlid-neutis-n5.dtsi b/arch/arm/dts/sun50i-h5-emlid-neutis-n5.dtsi
index 8e1e37db27d6..6db485584333 100644
--- a/arch/arm/dts/sun50i-h5-emlid-neutis-n5.dtsi
+++ b/arch/arm/dts/sun50i-h5-emlid-neutis-n5.dtsi
@@ -1,96 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+// Copyright (C) 2018 Aleksandr Aleksandrov <aleksandr.aleksandrov at emlid.com>
+
 /*
- * Copyright (C) 2018 Aleksandr Aleksandrov <aleksandr.aleksandrov at emlid.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This library is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This library is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
+ * DTSI for Emlid Neutis N5 SoM.
  */
 
 /dts-v1/;
 
 #include "sun50i-h5.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
-	reg_vcc3v3: vcc3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	wifi_pwrseq: wifi_pwrseq {
-		compatible = "mmc-pwrseq-simple";
-		pinctrl-names = "default";
-		reset-gpios = <&pio 2 7 GPIO_ACTIVE_LOW>; /* PC7 */
-		post-power-on-delay-ms = <200>;
-	};
-};
-
-&mmc1 {
-	vmmc-supply = <&reg_vcc3v3>;
-	vqmmc-supply = <&reg_vcc3v3>;
-	mmc-pwrseq = <&wifi_pwrseq>;
-	bus-width = <4>;
-	non-removable;
-	status = "okay";
-
-	brcmf: wifi at 1 {
-		reg = <1>;
-		compatible = "brcm,bcm4329-fmac";
-		interrupt-parent = <&r_pio>;
-		interrupts = <0 5 IRQ_TYPE_LEVEL_LOW>;	/* PL5 */
-		interrupt-names = "host-wake";
-	};
-};
-
-&mmc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc2_8bit_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
-	bus-width = <8>;
-	non-removable;
-	cap-mmc-hw-reset;
-	status = "okay";
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
-	status = "okay";
-};
+#include <sunxi-h3-h5-emlid-neutis.dtsi>
diff --git a/arch/arm/dts/sun50i-h5-libretech-all-h3-cc.dts b/arch/arm/dts/sun50i-h5-libretech-all-h3-cc.dts
index a35f77de22d8..a91806618e6f 100644
--- a/arch/arm/dts/sun50i-h5-libretech-all-h3-cc.dts
+++ b/arch/arm/dts/sun50i-h5-libretech-all-h3-cc.dts
@@ -1,8 +1,6 @@
 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Copyright (C) 2018 BayLibre, SAS
- * Author: Neil Armstrong <narmstrong at baylibre.com>
- */
+// Copyright (C) 2018 BayLibre, SAS
+// Author: Neil Armstrong <narmstrong at baylibre.com>
 
 /dts-v1/;
 #include "sun50i-h5.dtsi"
@@ -12,3 +10,7 @@
 	model = "Libre Computer Board ALL-H3-CC H5";
 	compatible = "libretech,all-h3-cc-h5", "allwinner,sun50i-h5";
 };
+
+&mmc2 {
+	mmc-ddr-3_3v;
+};
diff --git a/arch/arm/dts/sun50i-h5-libretech-all-h3-it.dts b/arch/arm/dts/sun50i-h5-libretech-all-h3-it.dts
new file mode 100644
index 000000000000..f6756d1bb057
--- /dev/null
+++ b/arch/arm/dts/sun50i-h5-libretech-all-h3-it.dts
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2019 Chen-Yu Tsai <wens at csie.org>
+
+/dts-v1/;
+#include "sun50i-h5.dtsi"
+#include <sunxi-libretech-all-h3-it.dtsi>
+
+/ {
+	model = "Libre Computer Board ALL-H3-IT H5";
+	compatible = "libretech,all-h3-it-h5", "allwinner,sun50i-h5";
+};
diff --git a/arch/arm/dts/sun50i-h5-libretech-all-h5-cc.dts b/arch/arm/dts/sun50i-h5-libretech-all-h5-cc.dts
new file mode 100644
index 000000000000..df1b9263ad0e
--- /dev/null
+++ b/arch/arm/dts/sun50i-h5-libretech-all-h5-cc.dts
@@ -0,0 +1,61 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2020 Chen-Yu Tsai <wens at csie.org>
+
+#include "sun50i-h5-libretech-all-h3-cc.dts"
+
+/ {
+	model = "Libre Computer Board ALL-H5-CC H5";
+	compatible = "libretech,all-h5-cc-h5", "allwinner,sun50i-h5";
+
+	aliases {
+		spi0 = &spi0;
+	};
+
+	reg_gmac_3v3: gmac-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "gmac-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <5000>;
+		enable-active-high;
+		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+		vin-supply = <&reg_vcc5v0>;
+	};
+};
+
+&codec {
+	/* No line out; only onboard microphone */
+	allwinner,audio-routing =
+		"MIC1", "Mic",
+		"Mic",  "MBIAS";
+};
+
+/* This board has external PHY */
+&emac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_rgmii_pins>;
+	phy-supply = <&reg_gmac_3v3>;
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii";
+	/delete-property/ allwinner,leds-active-low;
+	status = "okay";
+};
+
+&external_mdio {
+	ext_rgmii_phy: ethernet-phy at 1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&spi0  {
+	status = "okay";
+
+	flash at 0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+	};
+};
diff --git a/arch/arm/dts/sun50i-h5-nanopi-neo-plus2.dts b/arch/arm/dts/sun50i-h5-nanopi-neo-plus2.dts
index 506e25ba028a..4f9ba53ffaae 100644
--- a/arch/arm/dts/sun50i-h5-nanopi-neo-plus2.dts
+++ b/arch/arm/dts/sun50i-h5-nanopi-neo-plus2.dts
@@ -1,45 +1,6 @@
-/*
- * Copyright (C) 2017 Antony Antony <antony at phenome.org>
- * Copyright (C) 2016 ARM Ltd.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2017 Antony Antony <antony at phenome.org>
+// Copyright (C) 2016 ARM Ltd.
 
 /dts-v1/;
 #include "sun50i-h5.dtsi"
@@ -78,7 +39,6 @@
 
 	reg_gmac_3v3: gmac-3v3 {
 		compatible = "regulator-fixed";
-		pinctrl-names = "default";
 		regulator-name = "gmac-3v3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
@@ -96,7 +56,6 @@
 
 	vdd_cpux: gpio-regulator {
 		compatible = "regulator-gpio";
-		pinctrl-names = "default";
 		regulator-name = "vdd-cpux";
 		regulator-type = "voltage";
 		regulator-boot-on;
@@ -106,13 +65,11 @@
 		regulator-ramp-delay = <50>; /* 4ms */
 		gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>;
 		gpios-states = <0x1>;
-		states = <1100000 0x0
-			  1300000 0x1>;
+		states = <1100000 0>, <1300000 1>;
 	};
 
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
-		pinctrl-names = "default";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
 		post-power-on-delay-ms = <200>;
 	};
@@ -191,7 +148,7 @@
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pa_pins>;
 	status = "okay";
 };
 
diff --git a/arch/arm/dts/sun50i-h5-nanopi-neo2.dts b/arch/arm/dts/sun50i-h5-nanopi-neo2.dts
index cc268a69786c..b059e20813bd 100644
--- a/arch/arm/dts/sun50i-h5-nanopi-neo2.dts
+++ b/arch/arm/dts/sun50i-h5-nanopi-neo2.dts
@@ -1,44 +1,5 @@
-/*
- * Copyright (C) 2017 Icenowy Zheng <icenowy at aosc.io>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2017 Icenowy Zheng <icenowy at aosc.io>
 
 /dts-v1/;
 #include "sun50i-h5.dtsi"
@@ -142,7 +103,7 @@
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pa_pins>;
 	status = "okay";
 };
 
diff --git a/arch/arm/dts/sun50i-h5-orangepi-pc2.dts b/arch/arm/dts/sun50i-h5-orangepi-pc2.dts
index 3e0d5a9c096d..70b5f0998421 100644
--- a/arch/arm/dts/sun50i-h5-orangepi-pc2.dts
+++ b/arch/arm/dts/sun50i-h5-orangepi-pc2.dts
@@ -1,44 +1,5 @@
-/*
- * Copyright (C) 2016 ARM Ltd.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2016 ARM Ltd.
 
 /dts-v1/;
 #include "sun50i-h5.dtsi"
@@ -180,7 +141,7 @@
 
 &ir {
 	pinctrl-names = "default";
-	pinctrl-0 = <&ir_pins_a>;
+	pinctrl-0 = <&r_ir_rx_pin>;
 	status = "okay";
 };
 
@@ -221,7 +182,7 @@
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pa_pins>;
 	status = "okay";
 };
 
diff --git a/arch/arm/dts/sun50i-h5-orangepi-prime.dts b/arch/arm/dts/sun50i-h5-orangepi-prime.dts
index b75ca4d7d001..cb44bfa5981f 100644
--- a/arch/arm/dts/sun50i-h5-orangepi-prime.dts
+++ b/arch/arm/dts/sun50i-h5-orangepi-prime.dts
@@ -1,47 +1,7 @@
-/*
- * Copyright (C) 2017 Icenowy Zheng <icenowy at aosc.xyz>
- *
- * Based on sun50i-h5-orangepi-pc2.dts, which is:
- *   Copyright (C) 2016 ARM Ltd.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2017 Icenowy Zheng <icenowy at aosc.xyz>
+// Based on sun50i-h5-orangepi-pc2.dts, which is:
+//   Copyright (C) 2016 ARM Ltd.
 
 /dts-v1/;
 #include "sun50i-h5.dtsi"
@@ -187,7 +147,7 @@
 
 &ir {
 	pinctrl-names = "default";
-	pinctrl-0 = <&ir_pins_a>;
+	pinctrl-0 = <&r_ir_rx_pin>;
 	status = "okay";
 };
 
@@ -224,7 +184,7 @@
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pa_pins>;
 	status = "okay";
 };
 
diff --git a/arch/arm/dts/sun50i-h5-orangepi-zero-plus.dts b/arch/arm/dts/sun50i-h5-orangepi-zero-plus.dts
index 1238de25a969..ef5ca6444220 100644
--- a/arch/arm/dts/sun50i-h5-orangepi-zero-plus.dts
+++ b/arch/arm/dts/sun50i-h5-orangepi-zero-plus.dts
@@ -1,9 +1,6 @@
-/*
- * Copyright (C) 2016 ARM Ltd.
- * Copyright (C) 2018 Hauke Mehrtens <hauke at hauke-m.de>
- *
- * SPDX-License-Identifier: (GPL-2.0+ OR X11)
- */
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2016 ARM Ltd.
+// Copyright (C) 2018 Hauke Mehrtens <hauke at hauke-m.de>
 
 /dts-v1/;
 #include "sun50i-h5.dtsi"
@@ -127,7 +124,7 @@
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pa_pins>;
 	status = "okay";
 };
 
diff --git a/arch/arm/dts/sun50i-h5-orangepi-zero-plus2.dts b/arch/arm/dts/sun50i-h5-orangepi-zero-plus2.dts
index 53c8c11620e0..c95a68541309 100644
--- a/arch/arm/dts/sun50i-h5-orangepi-zero-plus2.dts
+++ b/arch/arm/dts/sun50i-h5-orangepi-zero-plus2.dts
@@ -1,44 +1,5 @@
-/*
- * Copyright (C) 2017 Jagan Teki <jteki at openedev.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This library is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This library is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2017 Jagan Teki <jteki at openedev.com>
 
 /dts-v1/;
 
@@ -78,7 +39,6 @@
 
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
-		pinctrl-names = "default";
 		reset-gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
 		post-power-on-delay-ms = <200>;
 	};
@@ -134,7 +94,7 @@
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pa_pins>;
 	status = "okay";
 };
 
diff --git a/arch/arm/dts/sun50i-h5.dtsi b/arch/arm/dts/sun50i-h5.dtsi
index 4e4738cab001..3a1c8b2efd69 100644
--- a/arch/arm/dts/sun50i-h5.dtsi
+++ b/arch/arm/dts/sun50i-h5.dtsi
@@ -1,44 +1,5 @@
-/*
- * Copyright (C) 2016 ARM Ltd.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2016 ARM Ltd.
 
 #include <sunxi-h3-h5.dtsi>
 
@@ -48,34 +9,44 @@
 		#size-cells = <0>;
 
 		cpu0: cpu at 0 {
-			compatible = "arm,cortex-a53", "arm,armv8";
+			compatible = "arm,cortex-a53";
 			device_type = "cpu";
 			reg = <0>;
 			enable-method = "psci";
 		};
 
-		cpu at 1 {
-			compatible = "arm,cortex-a53", "arm,armv8";
+		cpu1: cpu at 1 {
+			compatible = "arm,cortex-a53";
 			device_type = "cpu";
 			reg = <1>;
 			enable-method = "psci";
 		};
 
-		cpu at 2 {
-			compatible = "arm,cortex-a53", "arm,armv8";
+		cpu2: cpu at 2 {
+			compatible = "arm,cortex-a53";
 			device_type = "cpu";
 			reg = <2>;
 			enable-method = "psci";
 		};
 
-		cpu at 3 {
-			compatible = "arm,cortex-a53", "arm,armv8";
+		cpu3: cpu at 3 {
+			compatible = "arm,cortex-a53";
 			device_type = "cpu";
 			reg = <3>;
 			enable-method = "psci";
 		};
 	};
 
+	pmu {
+		compatible = "arm,cortex-a53-pmu",
+			     "arm,armv8-pmuv3";
+		interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
 	psci {
 		compatible = "arm,psci-0.2";
 		method = "smc";
@@ -92,6 +63,117 @@
 			     <GIC_PPI 10
 				(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
 	};
+
+	soc {
+		syscon: system-control at 1c00000 {
+			compatible = "allwinner,sun50i-h5-system-control";
+			reg = <0x01c00000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			sram_c1: sram at 18000 {
+				compatible = "mmio-sram";
+				reg = <0x00018000 0x1c000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x00018000 0x1c000>;
+
+				ve_sram: sram-section at 0 {
+					compatible = "allwinner,sun50i-h5-sram-c1",
+						     "allwinner,sun4i-a10-sram-c1";
+					reg = <0x000000 0x1c000>;
+				};
+			};
+		};
+
+		video-codec at 1c0e000 {
+			compatible = "allwinner,sun50i-h5-video-engine";
+			reg = <0x01c0e000 0x1000>;
+			clocks = <&ccu CLK_BUS_VE>, <&ccu CLK_VE>,
+				 <&ccu CLK_DRAM_VE>;
+			clock-names = "ahb", "mod", "ram";
+			resets = <&ccu RST_BUS_VE>;
+			interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+			allwinner,sram = <&ve_sram 1>;
+		};
+
+		crypto: crypto at 1c15000 {
+			compatible = "allwinner,sun50i-h5-crypto";
+			reg = <0x01c15000 0x1000>;
+			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_CE>, <&ccu CLK_CE>;
+			clock-names = "bus", "mod";
+			resets = <&ccu RST_BUS_CE>;
+		};
+
+		mali: gpu at 1e80000 {
+			compatible = "allwinner,sun50i-h5-mali", "arm,mali-450";
+			reg = <0x01e80000 0x30000>;
+			/*
+			 * While the datasheet lists an interrupt for the
+			 * PMU, the actual silicon does not have the PMU
+			 * block. Reads all return zero, and writes are
+			 * ignored.
+			 */
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "gp",
+					  "gpmmu",
+					  "pp",
+					  "pp0",
+					  "ppmmu0",
+					  "pp1",
+					  "ppmmu1",
+					  "pp2",
+					  "ppmmu2",
+					  "pp3",
+					  "ppmmu3",
+					  "pmu";
+			clocks = <&ccu CLK_BUS_GPU>, <&ccu CLK_GPU>;
+			clock-names = "bus", "core";
+			resets = <&ccu RST_BUS_GPU>;
+
+			assigned-clocks = <&ccu CLK_GPU>;
+			assigned-clock-rates = <384000000>;
+		};
+
+		ths: thermal-sensor at 1c25000 {
+			compatible = "allwinner,sun50i-h5-ths";
+			reg = <0x01c25000 0x400>;
+			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+			resets = <&ccu RST_BUS_THS>;
+			clocks = <&ccu CLK_BUS_THS>, <&ccu CLK_THS>;
+			clock-names = "bus", "mod";
+			nvmem-cells = <&ths_calibration>;
+			nvmem-cell-names = "calibration";
+			#thermal-sensor-cells = <1>;
+		};
+	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&ths 0>;
+		};
+
+		gpu_thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&ths 1>;
+		};
+	};
 };
 
 &ccu {
@@ -129,3 +211,11 @@
 		     <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
 	compatible = "allwinner,sun50i-h5-pinctrl";
 };
+
+&rtc {
+	compatible = "allwinner,sun50i-h5-rtc";
+};
+
+&sid {
+	compatible = "allwinner,sun50i-h5-sid";
+};
diff --git a/arch/arm/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/dts/sun8i-h2-plus-bananapi-m2-zero.dts
index 7d01f9322658..d277d043031b 100644
--- a/arch/arm/dts/sun8i-h2-plus-bananapi-m2-zero.dts
+++ b/arch/arm/dts/sun8i-h2-plus-bananapi-m2-zero.dts
@@ -28,7 +28,6 @@
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
 
 		pwr_led {
 			label = "bananapi-m2-zero:red:pwr";
@@ -39,7 +38,6 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
-		pinctrl-names = "default";
 
 		sw4 {
 			label = "power";
@@ -48,13 +46,34 @@
 		};
 	};
 
+	reg_vdd_cpux: vdd-cpux-regulator {
+		compatible = "regulator-gpio";
+		regulator-name = "vdd-cpux";
+		regulator-type = "voltage";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1300000>;
+		regulator-ramp-delay = <50>; /* 4ms */
+
+		gpios = <&r_pio 0 1 GPIO_ACTIVE_HIGH>; /* PL1 */
+		enable-active-high;
+		gpios-states = <0x1>;
+		states = <1100000 0>, <1300000 1>;
+	};
+
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
-		pinctrl-names = "default";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+		clocks = <&rtc 1>;
+		clock-names = "ext_clock";
 	};
 };
 
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
 &ehci0 {
 	status = "okay";
 };
@@ -94,14 +113,27 @@
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pa_pins>;
 	status = "okay";
 };
 
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	uart-has-rtscts;
 	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&rtc 1>;
+		clock-names = "lpo";
+		vbat-supply = <&reg_vcc3v3>;
+		vddio-supply = <&reg_vcc3v3>;
+		device-wakeup-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
+		host-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
+		shutdown-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+	};
+
 };
 
 &usb_otg {
diff --git a/arch/arm/dts/sun8i-h2-plus-orangepi-r1.dts b/arch/arm/dts/sun8i-h2-plus-orangepi-r1.dts
index c652ac3b712c..3356f4210d45 100644
--- a/arch/arm/dts/sun8i-h2-plus-orangepi-r1.dts
+++ b/arch/arm/dts/sun8i-h2-plus-orangepi-r1.dts
@@ -68,7 +68,6 @@
 	};
 };
 
-/*
 &spi0 {
 	status = "okay";
 
@@ -76,7 +75,6 @@
 		compatible = "mxicy,mx25l12805d", "jedec,spi-nor";
 	};
 };
-*/
 
 &ohci1 {
 	/*
diff --git a/arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts
index 0bc031fe4c56..f19ed981da9d 100644
--- a/arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts
+++ b/arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts
@@ -89,6 +89,22 @@
 		gpio = <&pio 0 20 GPIO_ACTIVE_HIGH>;
 	};
 
+	reg_vdd_cpux: vdd-cpux-regulator {
+		compatible = "regulator-gpio";
+		regulator-name = "vdd-cpux";
+		regulator-type = "voltage";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1300000>;
+		regulator-ramp-delay = <50>; /* 4ms */
+
+		gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+		enable-active-high;
+		gpios-states = <1>;
+		states = <1100000 0>, <1300000 1>;
+	};
+
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>;
@@ -96,6 +112,10 @@
 	};
 };
 
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
 &ehci0 {
 	status = "okay";
 };
@@ -157,7 +177,7 @@
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pa_pins>;
 	status = "okay";
 };
 
diff --git a/arch/arm/dts/sun8i-h3-bananapi-m2-plus-v1.2.dts b/arch/arm/dts/sun8i-h3-bananapi-m2-plus-v1.2.dts
new file mode 100644
index 000000000000..fc4a8c3d084d
--- /dev/null
+++ b/arch/arm/dts/sun8i-h3-bananapi-m2-plus-v1.2.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2018 Chen-Yu Tsai <wens at csie.org>
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-bananapi-m2-plus-v1.2.dtsi"
+
+/ {
+	model = "Banana Pi BPI-M2-Plus v1.2 H3";
+	compatible = "bananapi,bpi-m2-plus-v1.2", "allwinner,sun8i-h3";
+};
diff --git a/arch/arm/dts/sun8i-h3-beelink-x2.dts b/arch/arm/dts/sun8i-h3-beelink-x2.dts
index 25540b7694d5..45a24441ff18 100644
--- a/arch/arm/dts/sun8i-h3-beelink-x2.dts
+++ b/arch/arm/dts/sun8i-h3-beelink-x2.dts
@@ -90,6 +90,8 @@
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+		clocks = <&rtc 1>;
+		clock-names = "ext_clock";
 	};
 
 	sound_spdif {
@@ -141,8 +143,9 @@
 };
 
 &ir {
+	linux,rc-map-name = "rc-tanix-tx3mini";
 	pinctrl-names = "default";
-	pinctrl-0 = <&ir_pins_a>;
+	pinctrl-0 = <&r_ir_rx_pin>;
 	status = "okay";
 };
 
@@ -155,6 +158,8 @@
 
 &mmc1 {
 	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
 	bus-width = <4>;
 	non-removable;
 	status = "okay";
@@ -193,13 +198,13 @@
 
 &spdif {
 	pinctrl-names = "default";
-	pinctrl-0 = <&spdif_tx_pins_a>;
+	pinctrl-0 = <&spdif_tx_pin>;
 	status = "okay";
 };
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pa_pins>;
 	status = "okay";
 };
 
diff --git a/arch/arm/dts/sun8i-h3-emlid-neutis-n5h3-devboard.dts b/arch/arm/dts/sun8i-h3-emlid-neutis-n5h3-devboard.dts
new file mode 100644
index 000000000000..02fbe00cde97
--- /dev/null
+++ b/arch/arm/dts/sun8i-h3-emlid-neutis-n5h3-devboard.dts
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * DTS for Emlid Neutis N5 Dev board.
+ *
+ * Copyright (C) 2019 Georgii Staroselskii <georgiii.staroselskii at emlid.com>
+ */
+
+/dts-v1/;
+
+#include "sun8i-h3-emlid-neutis-n5h3.dtsi"
+
+/ {
+	model = "Emlid Neutis N5H3 Developer board";
+	compatible = "emlid,neutis-n5h3-devboard",
+		     "emlid,neutis-n5h3",
+		     "allwinner,sun8i-h3";
+
+	vdd_cpux: gpio-regulator {
+		compatible = "regulator-gpio";
+		regulator-name = "vdd-cpux";
+		regulator-type = "voltage";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1300000>;
+		regulator-ramp-delay = <50>; /* 4ms */
+		gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+		gpios-states = <0x1>;
+		states = <1100000 0x0>, <1300000 0x1>;
+	};
+
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_cpux>;
+};
+
+&codec {
+	status = "okay";
+};
+
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
diff --git a/arch/arm/dts/sun8i-h3-emlid-neutis-n5h3.dtsi b/arch/arm/dts/sun8i-h3-emlid-neutis-n5h3.dtsi
new file mode 100644
index 000000000000..3f5c63e582bf
--- /dev/null
+++ b/arch/arm/dts/sun8i-h3-emlid-neutis-n5h3.dtsi
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * DTSI for Emlid Neutis N5 SoM.
+ *
+ * Copyright (C) 2019 Georgii Staroselskii <georgii.staroselskii at emlid.com>
+ */
+
+/dts-v1/;
+
+#include "sun8i-h3.dtsi"
+#include <sunxi-h3-h5-emlid-neutis.dtsi>
diff --git a/arch/arm/dts/sun8i-h3-mapleboard-mp130.dts b/arch/arm/dts/sun8i-h3-mapleboard-mp130.dts
new file mode 100644
index 000000000000..ff0a7a952e0c
--- /dev/null
+++ b/arch/arm/dts/sun8i-h3-mapleboard-mp130.dts
@@ -0,0 +1,152 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 Centrum Embedded Systems, Jia-Bin Huang <jb at ces.com.tw>
+ * Copyright (C) 2018 Jonathan McDowell <noodles at earth.li>
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "MapleBoard MP130";
+	compatible = "mapleboard,mp130", "allwinner,sun8i-h3";
+
+	aliases {
+		ethernet0 = &emac;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pwr_led {
+			label = "mp130:orange:pwr";
+			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		status_led {
+			label = "mp130:orange:status";
+			gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	r_gpio_keys {
+		compatible = "gpio-keys";
+
+		power {
+			label = "power";
+			linux,code = <KEY_POWER>;
+			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; /* PL3 */
+		};
+
+		user {
+			label = "user";
+			linux,code = <BTN_0>;
+			gpios = <&r_pio 0 4 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&codec {
+	allwinner,audio-routing =
+		"Line Out", "LINEOUT",
+		"LINEIN", "Line In";
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
+&ir {
+	pinctrl-names = "default";
+	pinctrl-0 = <&r_ir_rx_pin>;
+	status = "okay";
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+	status = "okay";
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pa_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "disabled";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "disabled";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+	status = "disabled";
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	/* USB VBUS is always on */
+	status = "okay";
+};
diff --git a/arch/arm/dts/sun8i-h3-nanopi-duo2.dts b/arch/arm/dts/sun8i-h3-nanopi-duo2.dts
new file mode 100644
index 000000000000..6b149271ef13
--- /dev/null
+++ b/arch/arm/dts/sun8i-h3-nanopi-duo2.dts
@@ -0,0 +1,173 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Karl Palsson <karlp at tweak.net.au>
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "FriendlyARM NanoPi Duo2";
+	compatible = "friendlyarm,nanopi-duo2", "allwinner,sun8i-h3";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pwr {
+			label = "nanopi:red:pwr";
+			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+			default-state = "on";
+		};
+
+		status {
+			label = "nanopi:green:status";
+			gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */
+		};
+	};
+
+	r_gpio_keys {
+		compatible = "gpio-keys";
+
+		k1 {
+			label = "k1";
+			linux,code = <BTN_0>;
+			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; /* PL3 */
+		};
+	};
+
+	reg_vdd_cpux: vdd-cpux-regulator {
+		compatible = "regulator-gpio";
+		regulator-name = "vdd-cpux";
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-ramp-delay = <50>; /* 4ms */
+
+		enable-active-high;
+		enable-gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+		gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+		gpios-states = <0x1>;
+		states = <1100000 0>, <1300000 1>;
+	};
+
+	reg_vcc_dram: vcc-dram {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-dram";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */
+		vin-supply = <&reg_vcc5v0>;
+        };
+
+	reg_vdd_sys: vdd-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-sys";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+		vin-supply = <&reg_vcc5v0>;
+        };
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+		clocks = <&rtc 1>;
+		clock-names = "ext_clock";
+	};
+
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&mmc0 {
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+	status = "okay";
+	vmmc-supply = <&reg_vcc3v3>;
+};
+
+&mmc1 {
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	sdio_wifi: sdio_wifi at 1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&pio>;
+		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&reg_usb0_vbus {
+	gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pa_pins>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>, <&uart2_rts_cts_pins>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&rtc 1>;
+		clock-names = "lpo";
+		vbat-supply = <&reg_vcc3v3>;
+		vddio-supply = <&reg_vcc3v3>;
+		device-wakeup-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */
+		host-wakeup-gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */
+		shutdown-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
+	};
+};
+
+&usb_otg {
+	status = "okay";
+	dr_mode = "otg";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
+	status = "okay";
+};
diff --git a/arch/arm/dts/sun8i-h3-nanopi-m1-plus.dts b/arch/arm/dts/sun8i-h3-nanopi-m1-plus.dts
index 65cba1050802..4ba533b0340f 100644
--- a/arch/arm/dts/sun8i-h3-nanopi-m1-plus.dts
+++ b/arch/arm/dts/sun8i-h3-nanopi-m1-plus.dts
@@ -64,9 +64,23 @@
 
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
-		pinctrl-names = "default";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
 	};
+
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+};
+
+&de {
+	status = "okay";
 };
 
 &ehci1 {
@@ -94,9 +108,19 @@
 	};
 };
 
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
 &ir {
 	pinctrl-names = "default";
-	pinctrl-0 = <&ir_pins_a>;
+	pinctrl-0 = <&r_ir_rx_pin>;
 	status = "okay";
 };
 
diff --git a/arch/arm/dts/sun8i-h3-nanopi-m1.dts b/arch/arm/dts/sun8i-h3-nanopi-m1.dts
index 9412668bb888..69243dcb30a6 100644
--- a/arch/arm/dts/sun8i-h3-nanopi-m1.dts
+++ b/arch/arm/dts/sun8i-h3-nanopi-m1.dts
@@ -93,7 +93,7 @@
 
 &ir {
 	pinctrl-names = "default";
-	pinctrl-0 = <&ir_pins_a>;
+	pinctrl-0 = <&r_ir_rx_pin>;
 	status = "okay";
 };
 
diff --git a/arch/arm/dts/sun8i-h3-nanopi-neo-air.dts b/arch/arm/dts/sun8i-h3-nanopi-neo-air.dts
index 6246d3eff39d..07867a0d569b 100644
--- a/arch/arm/dts/sun8i-h3-nanopi-neo-air.dts
+++ b/arch/arm/dts/sun8i-h3-nanopi-neo-air.dts
@@ -105,7 +105,7 @@
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pa_pins>;
 	status = "okay";
 };
 
diff --git a/arch/arm/dts/sun8i-h3-nanopi.dtsi b/arch/arm/dts/sun8i-h3-nanopi.dtsi
index f110ee382239..4df29a65316d 100644
--- a/arch/arm/dts/sun8i-h3-nanopi.dtsi
+++ b/arch/arm/dts/sun8i-h3-nanopi.dtsi
@@ -59,8 +59,6 @@
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&leds_npi>, <&leds_r_npi>;
 
 		status {
 			label = "nanopi:blue:status";
@@ -78,8 +76,6 @@
 	r_gpio_keys {
 		compatible = "gpio-keys";
 		input-name = "k1";
-		pinctrl-names = "default";
-		pinctrl-0 = <&sw_r_npi>;
 
 		k1 {
 			label = "k1";
@@ -104,28 +100,9 @@
 	status = "okay";
 };
 
-&pio {
-	leds_npi: led_pins {
-		pins = "PA10";
-		function = "gpio_out";
-	};
-};
-
-&r_pio {
-	leds_r_npi: led_pins {
-		pins = "PL10";
-		function = "gpio_out";
-	};
-
-	sw_r_npi: key_pins {
-		pins = "PL3";
-		function = "gpio_in";
-	};
-};
-
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pa_pins>;
 	status = "okay";
 };
 
diff --git a/arch/arm/dts/sun8i-h3-orangepi-2.dts b/arch/arm/dts/sun8i-h3-orangepi-2.dts
index f1fc6bdca8be..597c425d08ec 100644
--- a/arch/arm/dts/sun8i-h3-orangepi-2.dts
+++ b/arch/arm/dts/sun8i-h3-orangepi-2.dts
@@ -75,8 +75,6 @@
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
 
 		status_led {
 			label = "orangepi:red:status";
@@ -92,8 +90,6 @@
 
 	r_gpio_keys {
 		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&sw_r_opc>;
 
 		sw2 {
 			label = "sw2";
@@ -110,8 +106,6 @@
 
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
-		pinctrl-names = "default";
-		pinctrl-0 = <&wifi_pwrseq_pin_orangepi>;
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 WIFI_EN */
 	};
 };
@@ -152,7 +146,7 @@
 
 &ir {
 	pinctrl-names = "default";
-	pinctrl-0 = <&ir_pins_a>;
+	pinctrl-0 = <&r_ir_rx_pin>;
 	status = "okay";
 };
 
@@ -179,30 +173,6 @@
 	};
 };
 
-&pio {
-	leds_opc: led_pins {
-		pins = "PA15";
-		function = "gpio_out";
-	};
-};
-
-&r_pio {
-	leds_r_opc: led_pins {
-		pins = "PL10";
-		function = "gpio_out";
-	};
-
-	sw_r_opc: key_pins {
-		pins = "PL3", "PL4";
-		function = "gpio_in";
-	};
-
-	wifi_pwrseq_pin_orangepi: wifi_pwrseq_pin {
-		pins = "PL7";
-		function = "gpio_out";
-	};
-};
-
 &reg_usb1_vbus {
 	gpio = <&pio 6 13 GPIO_ACTIVE_HIGH>;
 	status = "okay";
@@ -210,7 +180,7 @@
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pa_pins>;
 	status = "okay";
 };
 
diff --git a/arch/arm/dts/sun8i-h3-orangepi-lite.dts b/arch/arm/dts/sun8i-h3-orangepi-lite.dts
index 476ae8e387ca..6f9c97add54e 100644
--- a/arch/arm/dts/sun8i-h3-orangepi-lite.dts
+++ b/arch/arm/dts/sun8i-h3-orangepi-lite.dts
@@ -74,8 +74,6 @@
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
 
 		pwr_led {
 			label = "orangepi:green:pwr";
@@ -91,8 +89,6 @@
 
 	r_gpio_keys {
 		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&sw_r_opc>;
 
 		sw4 {
 			label = "sw4";
@@ -126,7 +122,7 @@
 
 &ir {
 	pinctrl-names = "default";
-	pinctrl-0 = <&ir_pins_a>;
+	pinctrl-0 = <&r_ir_rx_pin>;
 	status = "okay";
 };
 
@@ -160,28 +156,9 @@
 	status = "okay";
 };
 
-&pio {
-	leds_opc: led_pins {
-		pins = "PA15";
-		function = "gpio_out";
-	};
-};
-
-&r_pio {
-	leds_r_opc: led_pins {
-		pins = "PL10";
-		function = "gpio_out";
-	};
-
-	sw_r_opc: key_pins {
-		pins = "PL3";
-		function = "gpio_in";
-	};
-};
-
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pa_pins>;
 	status = "okay";
 };
 
diff --git a/arch/arm/dts/sun8i-h3-orangepi-one.dts b/arch/arm/dts/sun8i-h3-orangepi-one.dts
index 245fd658defb..4759ba3f2986 100644
--- a/arch/arm/dts/sun8i-h3-orangepi-one.dts
+++ b/arch/arm/dts/sun8i-h3-orangepi-one.dts
@@ -73,8 +73,6 @@
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
 
 		pwr_led {
 			label = "orangepi:green:pwr";
@@ -90,8 +88,6 @@
 
 	r_gpio_keys {
 		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&sw_r_opc>;
 
 		sw4 {
 			label = "sw4";
@@ -113,8 +109,7 @@
 		gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
 		enable-active-high;
 		gpios-states = <0x1>;
-		states = <1100000 0x0
-			  1300000 0x1>;
+		states = <1100000 0>, <1300000 1>;
 	};
 };
 
@@ -166,25 +161,6 @@
 	status = "okay";
 };
 
-&pio {
-	leds_opc: led_pins {
-		pins = "PA15";
-		function = "gpio_out";
-	};
-};
-
-&r_pio {
-	leds_r_opc: led_pins {
-		pins = "PL10";
-		function = "gpio_out";
-	};
-
-	sw_r_opc: key_pins {
-		pins = "PL3";
-		function = "gpio_in";
-	};
-};
-
 &reg_usb0_vbus {
 	gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
 	status = "okay";
@@ -192,7 +168,7 @@
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pa_pins>;
 	status = "okay";
 };
 
diff --git a/arch/arm/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/dts/sun8i-h3-orangepi-pc.dts
index 46240334128f..5aff8ecc66cb 100644
--- a/arch/arm/dts/sun8i-h3-orangepi-pc.dts
+++ b/arch/arm/dts/sun8i-h3-orangepi-pc.dts
@@ -73,8 +73,6 @@
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
 
 		pwr_led {
 			label = "orangepi:green:pwr";
@@ -90,8 +88,6 @@
 
 	r_gpio_keys {
 		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&sw_r_opc>;
 
 		sw4 {
 			label = "sw4";
@@ -152,7 +148,7 @@
 
 &ir {
 	pinctrl-names = "default";
-	pinctrl-0 = <&ir_pins_a>;
+	pinctrl-0 = <&r_ir_rx_pin>;
 	status = "okay";
 };
 
@@ -179,13 +175,6 @@
 	status = "okay";
 };
 
-&pio {
-	leds_opc: led_pins {
-		pins = "PA15";
-		function = "gpio_out";
-	};
-};
-
 &r_i2c {
 	status = "okay";
 
@@ -210,18 +199,6 @@
 	};
 };
 
-&r_pio {
-	leds_r_opc: led_pins {
-		pins = "PL10";
-		function = "gpio_out";
-	};
-
-	sw_r_opc: key_pins {
-		pins = "PL3";
-		function = "gpio_in";
-	};
-};
-
 &reg_usb0_vbus {
 	gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
 	status = "okay";
@@ -229,7 +206,7 @@
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pa_pins>;
 	status = "okay";
 };
 
diff --git a/arch/arm/dts/sun8i-h3-orangepi-plus.dts b/arch/arm/dts/sun8i-h3-orangepi-plus.dts
index b403e5d787cb..97f497854e05 100644
--- a/arch/arm/dts/sun8i-h3-orangepi-plus.dts
+++ b/arch/arm/dts/sun8i-h3-orangepi-plus.dts
@@ -63,8 +63,6 @@
 
 	reg_usb3_vbus: usb3-vbus {
 		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&usb3_vbus_pin_a>;
 		regulator-name = "usb3-vbus";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
@@ -74,6 +72,10 @@
 	};
 };
 
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
 &ehci3 {
 	status = "okay";
 };
@@ -112,10 +114,19 @@
 	bias-pull-up;
 };
 
-&pio {
-	usb3_vbus_pin_a: usb3_vbus_pin {
-		pins = "PG11";
-		function = "gpio_out";
+&r_i2c {
+	status = "okay";
+
+	reg_vdd_cpux: regulator at 65 {
+		compatible = "silergy,sy8106a";
+		reg = <0x65>;
+		regulator-name = "vdd-cpux";
+		silergy,fixed-microvolt = <1200000>;
+		regulator-min-microvolt = <1000000>;
+		regulator-max-microvolt = <1400000>;
+		regulator-ramp-delay = <200>;
+		regulator-boot-on;
+		regulator-always-on;
 	};
 };
 
diff --git a/arch/arm/dts/sun8i-h3-orangepi-zero-plus2.dts b/arch/arm/dts/sun8i-h3-orangepi-zero-plus2.dts
index f2f7b7a92571..b8f46e2802fd 100644
--- a/arch/arm/dts/sun8i-h3-orangepi-zero-plus2.dts
+++ b/arch/arm/dts/sun8i-h3-orangepi-zero-plus2.dts
@@ -134,6 +134,6 @@
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pa_pins>;
 	status = "okay";
 };
diff --git a/arch/arm/dts/sun8i-h3-rervision-dvk.dts b/arch/arm/dts/sun8i-h3-rervision-dvk.dts
new file mode 100644
index 000000000000..4738f3a9efe4
--- /dev/null
+++ b/arch/arm/dts/sun8i-h3-rervision-dvk.dts
@@ -0,0 +1,114 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019 Bootlin
+ * Author: Paul Kocialkowski <paul.kocialkowski at bootlin.com>
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "RerVision H3-DVK";
+	compatible = "rervision,h3-dvk", "allwinner,sun8i-h3";
+
+	aliases {
+		ethernet0 = &emac;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	allwinner,leds-active-low;
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&mmc0 {
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+	status = "okay";
+	vmmc-supply = <&reg_vcc3v3>;
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pa_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	status = "okay";
+	dr_mode = "peripheral";
+};
+
+&usbphy {
+	status = "okay";
+};
diff --git a/arch/arm/dts/sun8i-h3.dtsi b/arch/arm/dts/sun8i-h3.dtsi
index f0096074a467..20217e2ca4d3 100644
--- a/arch/arm/dts/sun8i-h3.dtsi
+++ b/arch/arm/dts/sun8i-h3.dtsi
@@ -47,19 +47,19 @@
 		compatible = "operating-points-v2";
 		opp-shared;
 
-		opp at 648000000 {
+		opp-648000000 {
 			opp-hz = /bits/ 64 <648000000>;
 			opp-microvolt = <1040000 1040000 1300000>;
 			clock-latency-ns = <244144>; /* 8 32k periods */
 		};
 
-		opp at 816000000 {
+		opp-816000000 {
 			opp-hz = /bits/ 64 <816000000>;
 			opp-microvolt = <1100000 1100000 1300000>;
 			clock-latency-ns = <244144>; /* 8 32k periods */
 		};
 
-		opp at 1008000000 {
+		opp-1008000000 {
 			opp-hz = /bits/ 64 <1008000000>;
 			opp-microvolt = <1200000 1200000 1300000>;
 			clock-latency-ns = <244144>; /* 8 32k periods */
@@ -80,7 +80,7 @@
 			#cooling-cells = <2>;
 		};
 
-		cpu at 1 {
+		cpu1: cpu at 1 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <1>;
@@ -90,7 +90,7 @@
 			#cooling-cells = <2>;
 		};
 
-		cpu at 2 {
+		cpu2: cpu at 2 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <2>;
@@ -100,7 +100,7 @@
 			#cooling-cells = <2>;
 		};
 
-		cpu at 3 {
+		cpu3: cpu at 3 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <3>;
@@ -111,6 +111,15 @@
 		};
 	};
 
+	pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
 	timer {
 		compatible = "arm,armv7-timer";
 		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
@@ -120,9 +129,22 @@
 	};
 
 	soc {
-		system-control at 1c00000 {
+		deinterlace: deinterlace at 1400000 {
+			compatible = "allwinner,sun8i-h3-deinterlace";
+			reg = <0x01400000 0x20000>;
+			clocks = <&ccu CLK_BUS_DEINTERLACE>,
+				 <&ccu CLK_DEINTERLACE>,
+				 <&ccu CLK_DRAM_DEINTERLACE>;
+			clock-names = "bus", "mod", "ram";
+			resets = <&ccu RST_BUS_DEINTERLACE>;
+			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+			interconnects = <&mbus 9>;
+			interconnect-names = "dma-mem";
+		};
+
+		syscon: system-control at 1c00000 {
 			compatible = "allwinner,sun8i-h3-system-control";
-			reg = <0x01c00000 0x30>;
+			reg = <0x01c00000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
@@ -142,6 +164,26 @@
 			};
 		};
 
+		video-codec at 1c0e000 {
+			compatible = "allwinner,sun8i-h3-video-engine";
+			reg = <0x01c0e000 0x1000>;
+			clocks = <&ccu CLK_BUS_VE>, <&ccu CLK_VE>,
+				 <&ccu CLK_DRAM_VE>;
+			clock-names = "ahb", "mod", "ram";
+			resets = <&ccu RST_BUS_VE>;
+			interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+			allwinner,sram = <&ve_sram 1>;
+		};
+
+		crypto: crypto at 1c15000 {
+			compatible = "allwinner,sun8i-h3-crypto";
+			reg = <0x01c15000 0x1000>;
+			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_CE>, <&ccu CLK_CE>;
+			clock-names = "bus", "mod";
+			resets = <&ccu RST_BUS_CE>;
+		};
+
 		mali: gpu at 1c40000 {
 			compatible = "allwinner,sun8i-h3-mali", "arm,mali-400";
 			reg = <0x01c40000 0x10000>;
@@ -166,6 +208,26 @@
 			assigned-clocks = <&ccu CLK_GPU>;
 			assigned-clock-rates = <384000000>;
 		};
+
+		ths: thermal-sensor at 1c25000 {
+			compatible = "allwinner,sun8i-h3-ths";
+			reg = <0x01c25000 0x400>;
+			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+			resets = <&ccu RST_BUS_THS>;
+			clocks = <&ccu CLK_BUS_THS>, <&ccu CLK_THS>;
+			clock-names = "bus", "mod";
+			nvmem-cells = <&ths_calibration>;
+			nvmem-cell-names = "calibration";
+			#thermal-sensor-cells = <0>;
+		};
+	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&ths 0>;
+		};
 	};
 };
 
@@ -216,3 +278,11 @@
 &pio {
 	compatible = "allwinner,sun8i-h3-pinctrl";
 };
+
+&rtc {
+	compatible = "allwinner,sun8i-h3-rtc";
+};
+
+&sid {
+	compatible = "allwinner,sun8i-h3-sid";
+};
diff --git a/arch/arm/dts/sunxi-bananapi-m2-plus-v1.2.dtsi b/arch/arm/dts/sunxi-bananapi-m2-plus-v1.2.dtsi
new file mode 100644
index 000000000000..22466afd38a3
--- /dev/null
+++ b/arch/arm/dts/sunxi-bananapi-m2-plus-v1.2.dtsi
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2018 Chen-Yu Tsai <wens at csie.org>
+ */
+
+#include "sunxi-bananapi-m2-plus.dtsi"
+
+/ {
+	/*
+	 * Bananapi M2+ v1.2 uses a GPIO line to change the effective
+	 * resistance on the CPU regulator's feedback pin.
+	 */
+	reg_vdd_cpux: vdd-cpux {
+		compatible = "regulator-gpio";
+		regulator-name = "vdd-cpux";
+		regulator-type = "voltage";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1300000>;
+		regulator-ramp-delay = <50>; /* 4ms */
+		gpios = <&r_pio 0 1 GPIO_ACTIVE_HIGH>; /* PL1 */
+		gpios-states = <0x1>;
+		states = <1100000 0>, <1300000 1>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
diff --git a/arch/arm/dts/sunxi-bananapi-m2-plus.dtsi b/arch/arm/dts/sunxi-bananapi-m2-plus.dtsi
index 3bed375b9c03..39263e74fbb5 100644
--- a/arch/arm/dts/sunxi-bananapi-m2-plus.dtsi
+++ b/arch/arm/dts/sunxi-bananapi-m2-plus.dtsi
@@ -69,7 +69,6 @@
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
 
 		pwr_led {
 			label = "bananapi-m2-plus:red:pwr";
@@ -80,7 +79,6 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
-		pinctrl-names = "default";
 
 		sw4 {
 			label = "power";
@@ -101,7 +99,6 @@
 
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
-		pinctrl-names = "default";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
 		clocks = <&rtc 1>;
 		clock-names = "ext_clock";
@@ -153,7 +150,7 @@
 
 &ir {
 	pinctrl-names = "default";
-	pinctrl-0 = <&ir_pins_a>;
+	pinctrl-0 = <&r_ir_rx_pin>;
 	status = "okay";
 };
 
@@ -210,7 +207,7 @@
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pa_pins>;
 	status = "okay";
 };
 
diff --git a/arch/arm/dts/sunxi-h3-h5-emlid-neutis.dtsi b/arch/arm/dts/sunxi-h3-h5-emlid-neutis.dtsi
new file mode 100644
index 000000000000..fc67e30fe212
--- /dev/null
+++ b/arch/arm/dts/sunxi-h3-h5-emlid-neutis.dtsi
@@ -0,0 +1,170 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * DTSI for Emlid Neutis SoMs.
+ *
+ * Copyright (C) 2019 Georgii Staroselskii <georgii.staroselskii at emlid.com>
+ */
+
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 2 7 GPIO_ACTIVE_LOW>; /* PC7 */
+		post-power-on-delay-ms = <200>;
+		clocks = <&rtc 1>;
+		clock-names = "ext_clock";
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_cpux>;
+};
+
+&reg_usb0_vbus {
+	gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>;   /* PL9 */
+	status = "okay";
+};
+
+
+&de {
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
+
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+	status = "okay";
+};
+
+
+&mmc1 {
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	brcmf: wifi at 1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&r_pio>;
+		interrupts = <0 5 IRQ_TYPE_LEVEL_LOW>;	/* PL5 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pa_pins>;
+	status = "okay";
+};
+
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&rtc 1>;
+		clock-names = "lpo";
+		vbat-supply = <&reg_vcc3v3>;
+		vddio-supply = <&reg_vcc3v3>;
+		shutdown-gpios = <&pio 2 4 GPIO_ACTIVE_HIGH>; /* PC4 */
+		device-wakeup-gpios = <&r_pio 0 7 GPIO_ACTIVE_HIGH>; /* PL7 */
+	};
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+	usb0_vbus-supply = <&reg_usb0_vbus>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&codec {
+	allwinner,audio-routing =
+		"Line Out", "LINEOUT",
+		"LINEIN", "Line In",
+		"MIC1", "Mic",
+		"MIC2", "Mic",
+		"Mic",  "MBIAS";
+};
+
+&i2c0 {
+	status = "okay";
+};
diff --git a/arch/arm/dts/sunxi-h3-h5.dtsi b/arch/arm/dts/sunxi-h3-h5.dtsi
index fc6131315c47..5e9c3060aa08 100644
--- a/arch/arm/dts/sunxi-h3-h5.dtsi
+++ b/arch/arm/dts/sunxi-h3-h5.dtsi
@@ -86,6 +86,7 @@
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <24000000>;
+			clock-accuracy = <50000>;
 			clock-output-names = "osc24M";
 		};
 
@@ -93,15 +94,8 @@
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <32768>;
-			clock-output-names = "osc32k";
-		};
-
-		iosc: internal-osc-clk {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <16000000>;
-			clock-accuracy = <300000000>;
-			clock-output-names = "iosc";
+			clock-accuracy = <50000>;
+			clock-output-names = "ext_osc32k";
 		};
 	};
 
@@ -115,15 +109,16 @@
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
+		dma-ranges;
 		ranges;
 
 		display_clocks: clock at 1000000 {
 			/* compatible is in per SoC .dtsi file */
 			reg = <0x01000000 0x100000>;
-			clocks = <&ccu CLK_DE>,
-				 <&ccu CLK_BUS_DE>;
-			clock-names = "mod",
-				      "bus";
+			clocks = <&ccu CLK_BUS_DE>,
+				 <&ccu CLK_DE>;
+			clock-names = "bus",
+				      "mod";
 			resets = <&ccu RST_BUS_DE>;
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -152,12 +147,6 @@
 			};
 		};
 
-		syscon: syscon at 1c00000 {
-			compatible = "allwinner,sun8i-h3-system-controller",
-				"syscon";
-			reg = <0x01c00000 0x1000>;
-		};
-
 		dma: dma-controller at 1c02000 {
 			compatible = "allwinner,sun8i-h3-dma";
 			reg = <0x01c02000 0x1000>;
@@ -239,6 +228,17 @@
 			#size-cells = <0>;
 		};
 
+		sid: eeprom at 1c14000 {
+			/* compatible is in per SoC .dtsi file */
+			reg = <0x1c14000 0x400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			ths_calibration: thermal-sensor-calibration at 34 {
+				reg = <0x34 4>;
+			};
+		};
+
 		usb_otg: usb at 1c19000 {
 			compatible = "allwinner,sun8i-h3-musb";
 			reg = <0x01c19000 0x400>;
@@ -249,6 +249,7 @@
 			phys = <&usbphy 0>;
 			phy-names = "usb";
 			extcon = <&usbphy 0>;
+			dr_mode = "otg";
 			status = "disabled";
 		};
 
@@ -375,7 +376,7 @@
 		ccu: clock at 1c20000 {
 			/* compatible is in per SoC .dtsi file */
 			reg = <0x01c20000 0x400>;
-			clocks = <&osc24M>, <&osc32k>;
+			clocks = <&osc24M>, <&rtc 0>;
 			clock-names = "hosc", "losc";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -386,14 +387,21 @@
 			reg = <0x01c20800 0x400>;
 			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
+			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&rtc 0>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			#gpio-cells = <3>;
 			interrupt-controller;
 			#interrupt-cells = <3>;
 
-			emac_rgmii_pins: emac0 {
+			csi_pins: csi-pins {
+				pins = "PE0", "PE2", "PE3", "PE4", "PE5",
+				       "PE6", "PE7", "PE8", "PE9", "PE10",
+				       "PE11";
+				function = "csi";
+			};
+
+			emac_rgmii_pins: emac-rgmii-pins {
 				pins = "PD0", "PD1", "PD2", "PD3", "PD4",
 				       "PD5", "PD7", "PD8", "PD9", "PD10",
 				       "PD12", "PD13", "PD15", "PD16", "PD17";
@@ -401,22 +409,22 @@
 				drive-strength = <40>;
 			};
 
-			i2c0_pins: i2c0 {
+			i2c0_pins: i2c0-pins {
 				pins = "PA11", "PA12";
 				function = "i2c0";
 			};
 
-			i2c1_pins: i2c1 {
+			i2c1_pins: i2c1-pins {
 				pins = "PA18", "PA19";
 				function = "i2c1";
 			};
 
-			i2c2_pins: i2c2 {
+			i2c2_pins: i2c2-pins {
 				pins = "PE12", "PE13";
 				function = "i2c2";
 			};
 
-			mmc0_pins: mmc0 {
+			mmc0_pins: mmc0-pins {
 				pins = "PF0", "PF1", "PF2", "PF3",
 				       "PF4", "PF5";
 				function = "mmc0";
@@ -424,7 +432,7 @@
 				bias-pull-up;
 			};
 
-			mmc1_pins: mmc1 {
+			mmc1_pins: mmc1-pins {
 				pins = "PG0", "PG1", "PG2", "PG3",
 				       "PG4", "PG5";
 				function = "mmc1";
@@ -432,7 +440,7 @@
 				bias-pull-up;
 			};
 
-			mmc2_8bit_pins: mmc2_8bit {
+			mmc2_8bit_pins: mmc2-8bit-pins {
 				pins = "PC5", "PC6", "PC8",
 				       "PC9", "PC10", "PC11",
 				       "PC12", "PC13", "PC14",
@@ -442,54 +450,59 @@
 				bias-pull-up;
 			};
 
-			spdif_tx_pins_a: spdif {
+			spdif_tx_pin: spdif-tx-pin {
 				pins = "PA17";
 				function = "spdif";
 			};
 
-			spi0_pins: spi0 {
+			spi0_pins: spi0-pins {
 				pins = "PC0", "PC1", "PC2", "PC3";
 				function = "spi0";
 			};
 
-			spi1_pins: spi1 {
+			spi1_pins: spi1-pins {
 				pins = "PA15", "PA16", "PA14", "PA13";
 				function = "spi1";
 			};
 
-			uart0_pins_a: uart0 {
+			uart0_pa_pins: uart0-pa-pins {
 				pins = "PA4", "PA5";
 				function = "uart0";
 			};
 
-			uart1_pins: uart1 {
+			uart1_pins: uart1-pins {
 				pins = "PG6", "PG7";
 				function = "uart1";
 			};
 
-			uart1_rts_cts_pins: uart1_rts_cts {
+			uart1_rts_cts_pins: uart1-rts-cts-pins {
 				pins = "PG8", "PG9";
 				function = "uart1";
 			};
 
-			uart2_pins: uart2 {
+			uart2_pins: uart2-pins {
 				pins = "PA0", "PA1";
 				function = "uart2";
 			};
 
-			uart3_pins: uart3 {
+			uart2_rts_cts_pins: uart2-rts-cts-pins {
+				pins = "PA2", "PA3";
+				function = "uart2";
+			};
+
+			uart3_pins: uart3-pins {
 				pins = "PA13", "PA14";
 				function = "uart3";
 			};
 
-			uart3_rts_cts_pins: uart3_rts_cts {
+			uart3_rts_cts_pins: uart3-rts-cts-pins {
 				pins = "PA15", "PA16";
 				function = "uart3";
 			};
 		};
 
 		timer at 1c20c00 {
-			compatible = "allwinner,sun4i-a10-timer";
+			compatible = "allwinner,sun8i-a23-timer";
 			reg = <0x01c20c00 0xa0>;
 			interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
@@ -543,6 +556,14 @@
 			};
 		};
 
+		mbus: dram-controller at 1c62000 {
+			compatible = "allwinner,sun8i-h3-mbus";
+			reg = <0x01c62000 0x1000>;
+			clocks = <&ccu CLK_MBUS>;
+			dma-ranges = <0x00000000 0x40000000 0xc0000000>;
+			#interconnect-cells = <1>;
+		};
+
 		spi0: spi at 1c68000 {
 			compatible = "allwinner,sun8i-h3-spi";
 			reg = <0x01c68000 0x1000>;
@@ -579,6 +600,7 @@
 			compatible = "allwinner,sun6i-a31-wdt";
 			reg = <0x01c20ca0 0x20>;
 			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc24M>;
 		};
 
 		spdif: spdif at 1c21000 {
@@ -744,6 +766,20 @@
 			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
 		};
 
+		csi: camera at 1cb0000 {
+			compatible = "allwinner,sun8i-h3-csi";
+			reg = <0x01cb0000 0x1000>;
+			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_CSI>,
+				 <&ccu CLK_CSI_SCLK>,
+				 <&ccu CLK_DRAM_CSI>;
+			clock-names = "bus", "mod", "ram";
+			resets = <&ccu RST_BUS_CSI>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&csi_pins>;
+			status = "disabled";
+		};
+
 		hdmi: hdmi at 1ee0000 {
 			compatible = "allwinner,sun8i-h3-dw-hdmi",
 				     "allwinner,sun8i-a83t-dw-hdmi";
@@ -756,7 +792,7 @@
 			resets = <&ccu RST_BUS_HDMI1>;
 			reset-names = "ctrl";
 			phys = <&hdmi_phy>;
-			phy-names = "hdmi-phy";
+			phy-names = "phy";
 			status = "disabled";
 
 			ports {
@@ -781,7 +817,7 @@
 			compatible = "allwinner,sun8i-h3-hdmi-phy";
 			reg = <0x01ef0000 0x10000>;
 			clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_DDC>,
-				 <&ccu 6>;
+				 <&ccu CLK_PLL_VIDEO>;
 			clock-names = "bus", "mod", "pll-0";
 			resets = <&ccu RST_BUS_HDMI0>;
 			reset-names = "phy";
@@ -789,17 +825,20 @@
 		};
 
 		rtc: rtc at 1f00000 {
-			compatible = "allwinner,sun6i-a31-rtc";
-			reg = <0x01f00000 0x54>;
+			/* compatible is in per SoC .dtsi file */
+			reg = <0x01f00000 0x400>;
 			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+			clock-output-names = "osc32k", "osc32k-out", "iosc";
+			clocks = <&osc32k>;
+			#clock-cells = <1>;
 		};
 
 		r_ccu: clock at 1f01400 {
 			compatible = "allwinner,sun8i-h3-r-ccu";
 			reg = <0x01f01400 0x100>;
-			clocks = <&osc24M>, <&osc32k>, <&iosc>,
-				 <&ccu 9>;
+			clocks = <&osc24M>, <&rtc 0>, <&rtc 2>,
+				 <&ccu CLK_PLL_PERIPH0>;
 			clock-names = "hosc", "losc", "iosc", "pll-periph";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -811,12 +850,12 @@
 		};
 
 		ir: ir at 1f02000 {
-			compatible = "allwinner,sun5i-a13-ir";
+			compatible = "allwinner,sun6i-a31-ir";
 			clocks = <&r_ccu CLK_APB0_IR>, <&r_ccu CLK_IR>;
 			clock-names = "apb", "ir";
 			resets = <&r_ccu RST_APB0_IR>;
 			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
-			reg = <0x01f02000 0x40>;
+			reg = <0x01f02000 0x400>;
 			status = "disabled";
 		};
 
@@ -837,19 +876,19 @@
 			compatible = "allwinner,sun8i-h3-r-pinctrl";
 			reg = <0x01f02c00 0x400>;
 			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&r_ccu CLK_APB0_PIO>, <&osc24M>, <&osc32k>;
+			clocks = <&r_ccu CLK_APB0_PIO>, <&osc24M>, <&rtc 0>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			#gpio-cells = <3>;
 			interrupt-controller;
 			#interrupt-cells = <3>;
 
-			ir_pins_a: ir {
+			r_ir_rx_pin: r-ir-rx-pin {
 				pins = "PL11";
 				function = "s_cir_rx";
 			};
 
-			r_i2c_pins: r-i2c {
+			r_i2c_pins: r-i2c-pins {
 				pins = "PL0", "PL1";
 				function = "s_i2c";
 			};
diff --git a/arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi b/arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi
index 14c8ec16d47e..19b3b23cfaa8 100644
--- a/arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi
+++ b/arch/arm/dts/sunxi-libretech-all-h3-cc.dtsi
@@ -16,6 +16,17 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 
@@ -44,8 +55,8 @@
 	reg_vcc1v2: vcc1v2 {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc1v2";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
 		regulator-always-on;
 		regulator-boot-on;
 		vin-supply = <&reg_vcc5v0>;
@@ -95,8 +106,8 @@
 	reg_vdd_cpux: vdd-cpux {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd-cpux";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
 		regulator-always-on;
 		regulator-boot-on;
 		vin-supply = <&reg_vcc5v0>;
@@ -105,6 +116,26 @@
 	};
 };
 
+&codec {
+	allwinner,audio-routing =
+		"Line Out", "LINEOUT",
+		"MIC1", "Mic",
+		"Mic",  "MBIAS";
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
 &ehci1 {
 	status = "okay";
 };
@@ -124,17 +155,26 @@
 	status = "okay";
 };
 
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
 &ir {
 	pinctrl-names = "default";
-	pinctrl-0 = <&ir_pins_a>;
+	pinctrl-0 = <&r_ir_rx_pin>;
 	status = "okay";
 };
 
 &mmc0 {
 	vmmc-supply = <&reg_vcc_io>;
 	bus-width = <4>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
-	cd-inverted;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
 	status = "okay";
 };
 
@@ -147,6 +187,10 @@
 	status = "okay";
 };
 
+&ohci0 {
+	status = "okay";
+};
+
 &ohci1 {
 	status = "okay";
 };
@@ -161,7 +205,12 @@
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pa_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "host";
 	status = "okay";
 };
 
diff --git a/arch/arm/dts/sunxi-libretech-all-h3-it.dtsi b/arch/arm/dts/sunxi-libretech-all-h3-it.dtsi
new file mode 100644
index 000000000000..204fba3614f9
--- /dev/null
+++ b/arch/arm/dts/sunxi-libretech-all-h3-it.dtsi
@@ -0,0 +1,180 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2019 Chen-Yu Tsai <wens at csie.org>
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	aliases {
+		serial0 = &uart0;
+		spi0 = &spi0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	connector {
+		compatible = "hdmi-connector";
+		type = "d";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		status_led {
+			label = "librecomputer:blue:status";
+			gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */
+		};
+	};
+
+	reg_vcc3v3: vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&reg_vcc5v0>;
+	};
+
+	/* This represents the board's 5V input */
+	reg_vcc5v0: vcc5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	reg_vcc_dram: vcc-dram {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-dram";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&reg_vcc5v0>;
+		gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */
+		enable-active-high;
+	};
+
+	reg_vcc_io: vcc-io {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-io";
+		/* This is simply a MOSFET switch */
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&reg_vcc3v3>;
+		gpio = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL5 */
+	};
+
+	reg_vcc_usbwifi: vcc-usbwifi {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-usbwifi";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_vcc5v0>;
+		gpio = <&pio 6 4 GPIO_ACTIVE_HIGH>; /* PG4 */
+		enable-active-high;
+	};
+
+	reg_vdd_cpux: vdd-cpux {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-cpux";
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&reg_vcc5v0>;
+		gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+		enable-active-high;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
+&cpu1 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
+&cpu2 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
+&cpu3 {
+	cpu-supply = <&reg_vdd_cpux>;
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc_io>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+	status = "okay";
+};
+
+&pio {
+	vcc-pa-supply = <&reg_vcc_io>;
+	vcc-pc-supply = <&reg_vcc_io>;
+	vcc-pd-supply = <&reg_vcc_io>;
+	vcc-pe-supply = <&reg_vcc_io>;
+	vcc-pf-supply = <&reg_vcc_io>;
+	vcc-pg-supply = <&reg_vcc_io>;
+};
+
+&r_pio {
+	vcc-pl-supply = <&reg_vcc3v3>;
+};
+
+&spi0 {
+	status = "okay";
+
+	spiflash at 0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pa_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_vcc_usbwifi>;
+	status = "okay";
+};
diff --git a/include/dt-bindings/clock/sun8i-h3-ccu.h b/include/dt-bindings/clock/sun8i-h3-ccu.h
index efb7ba2bd515..30d2d15373a2 100644
--- a/include/dt-bindings/clock/sun8i-h3-ccu.h
+++ b/include/dt-bindings/clock/sun8i-h3-ccu.h
@@ -43,6 +43,10 @@
 #ifndef _DT_BINDINGS_CLK_SUN8I_H3_H_
 #define _DT_BINDINGS_CLK_SUN8I_H3_H_
 
+#define CLK_PLL_VIDEO		6
+
+#define CLK_PLL_PERIPH0		9
+
 #define CLK_CPUX		14
 
 #define CLK_BUS_CE		20
@@ -91,7 +95,7 @@
 #define CLK_BUS_UART1		63
 #define CLK_BUS_UART2		64
 #define CLK_BUS_UART3		65
-#define CLK_BUS_SCR		66
+#define CLK_BUS_SCR0		66
 #define CLK_BUS_EPHY		67
 #define CLK_BUS_DBG		68
 
@@ -139,7 +143,10 @@
 #define CLK_AVS			110
 #define CLK_HDMI		111
 #define CLK_HDMI_DDC		112
-
+#define CLK_MBUS		113
 #define CLK_GPU			114
 
+/* New clocks imported in H5 */
+#define CLK_BUS_SCR1		115
+
 #endif /* _DT_BINDINGS_CLK_SUN8I_H3_H_ */
diff --git a/include/dt-bindings/reset/sun8i-h3-ccu.h b/include/dt-bindings/reset/sun8i-h3-ccu.h
index 6b7af80c26ec..484c2a22919d 100644
--- a/include/dt-bindings/reset/sun8i-h3-ccu.h
+++ b/include/dt-bindings/reset/sun8i-h3-ccu.h
@@ -98,6 +98,9 @@
 #define RST_BUS_UART1		50
 #define RST_BUS_UART2		51
 #define RST_BUS_UART3		52
-#define RST_BUS_SCR		53
+#define RST_BUS_SCR0		53
+
+/* New resets imported in H5 */
+#define RST_BUS_SCR1		54
 
 #endif /* _DT_BINDINGS_RST_SUN8I_H3_H_ */
