| Message ID | 20170511144422.24549-3-nsekhar@ti.com |
|---|---|
| State | Accepted |
| Commit | 936909e6e14db2230b906a4417afdd1d52e44471 |
| Headers | show |
| Series | davinci: omapl138_lcdk: enable commonly used commands | expand |
On Thu, May 11, 2017 at 08:14:22PM +0530, Sekhar Nori wrote: > Now that we support using TI_COMMON_CMD_OPTIONS, > we dont have to enable a number of commands explicitly > in the defconfig if we enable TI_COMMON_CMD_OPTIONS. > > Enable TI_COMMON_CMD_OPTIONS and regenerate the defconfig > using "make savedefconfig". > > CMD_GPIO has been kept disabled because there is no GPIO > support (yet) on OMAP-L138 LCDK. > > Signed-off-by: Sekhar Nori <nsekhar@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> -- Tom
On Thu, May 11, 2017 at 08:14:22PM +0530, Sekhar Nori wrote: > Now that we support using TI_COMMON_CMD_OPTIONS, > we dont have to enable a number of commands explicitly > in the defconfig if we enable TI_COMMON_CMD_OPTIONS. > > Enable TI_COMMON_CMD_OPTIONS and regenerate the defconfig > using "make savedefconfig". > > CMD_GPIO has been kept disabled because there is no GPIO > support (yet) on OMAP-L138 LCDK. > > Signed-off-by: Sekhar Nori <nsekhar@ti.com> > Reviewed-by: Tom Rini <trini@konsulko.com> Applied to u-boot/master, thanks! -- Tom
diff --git a/configs/omapl138_lcdk_defconfig b/configs/omapl138_lcdk_defconfig index 7a5a78f4944b..752ff5d860a1 100644 --- a/configs/omapl138_lcdk_defconfig +++ b/configs/omapl138_lcdk_defconfig @@ -1,6 +1,7 @@ CONFIG_ARM=y CONFIG_ARCH_DAVINCI=y CONFIG_TARGET_OMAPL138_LCDK=y +CONFIG_TI_COMMON_CMD_OPTIONS=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_SPL_MMC_SUPPORT=y @@ -15,19 +16,10 @@ CONFIG_SPL=y CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0xb5 CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="U-Boot > " -CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set -CONFIG_CMD_ASKENV=y # CONFIG_CMD_FLASH is not set -CONFIG_CMD_MMC=y -CONFIG_CMD_PART=y +# CONFIG_CMD_GPIO is not set # CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y -CONFIG_CMD_EXT2=y -CONFIG_CMD_FAT=y -CONFIG_CMD_FS_GENERIC=y CONFIG_CMD_DIAG=y CONFIG_CMD_UBI=y CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y
Now that we support using TI_COMMON_CMD_OPTIONS, we dont have to enable a number of commands explicitly in the defconfig if we enable TI_COMMON_CMD_OPTIONS. Enable TI_COMMON_CMD_OPTIONS and regenerate the defconfig using "make savedefconfig". CMD_GPIO has been kept disabled because there is no GPIO support (yet) on OMAP-L138 LCDK. Signed-off-by: Sekhar Nori <nsekhar@ti.com> --- configs/omapl138_lcdk_defconfig | 12 ++---------- 1 file changed, 2 insertions(+), 10 deletions(-)