From patchwork Thu Mar 26 22:42:01 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: "tomcwarren3959 at gmail.com" X-Patchwork-Id: 244359 List-Id: U-Boot discussion From: tomcwarren3959 at gmail.com (tomcwarren3959 at gmail.com) Date: Thu, 26 Mar 2020 15:42:01 -0700 Subject: [PATCH 2/3] qspi: t210: Fix QSPI clock and tap delays In-Reply-To: <1585262522-6127-1-git-send-email-tomcwarren3959@gmail.com> References: <1585262522-6127-1-git-send-email-tomcwarren3959@gmail.com> Message-ID: <1585262522-6127-3-git-send-email-tomcwarren3959@gmail.com> From: Tom Warren When claim_bus was setting the clock, it reset the QSPI controller, which wipes out any tap delays set by previous bootloaders (nvtboot, CBoot for example on Nano). Instead of doing that in claim_bus, which gets called a lot, moved clock setting to probe(), and set tap delays there, too. Also updated clock to 80MHz to match CBoot. Now QSPI env save works reliably again. Signed-off-by: Tom Warren --- Changes in v2: - None drivers/spi/tegra210_qspi.c | 19 ++++++++++++------- 1 file changed, 12 insertions(+), 7 deletions(-) diff --git a/drivers/spi/tegra210_qspi.c b/drivers/spi/tegra210_qspi.c index 2a77126..4284ea9 100644 --- a/drivers/spi/tegra210_qspi.c +++ b/drivers/spi/tegra210_qspi.c @@ -42,10 +42,10 @@ DECLARE_GLOBAL_DATA_PTR; #define QSPI_CMD1_BITLEN_SHIFT 0 /* COMMAND2 */ -#define QSPI_CMD2_TX_CLK_TAP_DELAY BIT(6) -#define QSPI_CMD2_TX_CLK_TAP_DELAY_MASK GENMASK(11,6) -#define QSPI_CMD2_RX_CLK_TAP_DELAY BIT(0) -#define QSPI_CMD2_RX_CLK_TAP_DELAY_MASK GENMASK(5,0) +#define QSPI_CMD2_TX_CLK_TAP_DELAY_SHIFT 10 +#define QSPI_CMD2_TX_CLK_TAP_DELAY_MASK GENMASK(14,10) +#define QSPI_CMD2_RX_CLK_TAP_DELAY_SHIFT 0 +#define QSPI_CMD2_RX_CLK_TAP_DELAY_MASK GENMASK(7,0) /* TRANSFER STATUS */ #define QSPI_XFER_STS_RDY BIT(30) @@ -127,14 +127,22 @@ static int tegra210_qspi_probe(struct udevice *bus) struct tegra210_qspi_priv *priv = dev_get_priv(bus); priv->regs = (struct qspi_regs *)plat->base; + struct qspi_regs *regs = priv->regs; priv->last_transaction_us = timer_get_us(); priv->freq = plat->frequency; priv->periph_id = plat->periph_id; + debug("%s: Freq = %u, id = %d\n", __func__, priv->freq, priv->periph_id); /* Change SPI clock to correct frequency, PLLP_OUT0 source */ clock_start_periph_pll(priv->periph_id, CLOCK_ID_PERIPH, priv->freq); + /* Set tap delays here, clock change above resets QSPI controller */ + u32 reg = (0x09 << QSPI_CMD2_TX_CLK_TAP_DELAY_SHIFT) | + (0x0C << QSPI_CMD2_RX_CLK_TAP_DELAY_SHIFT); + writel(reg, ®s->command2); + debug("%s: COMMAND2 = %08x\n", __func__, readl(®s->command2)); + return 0; } @@ -144,9 +152,6 @@ static int tegra210_qspi_claim_bus(struct udevice *dev) struct tegra210_qspi_priv *priv = dev_get_priv(bus); struct qspi_regs *regs = priv->regs; - /* Change SPI clock to correct frequency, PLLP_OUT0 source */ - clock_start_periph_pll(priv->periph_id, CLOCK_ID_PERIPH, priv->freq); - debug("%s: FIFO STATUS = %08x\n", __func__, readl(®s->fifo_status)); /* Set master mode and sw controlled CS */