From patchwork Thu Mar 19 01:52:13 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Alex Nemirovsky X-Patchwork-Id: 243887 List-Id: U-Boot discussion From: alex.nemirovsky at cortina-access.com (Alex Nemirovsky) Date: Wed, 18 Mar 2020 18:52:13 -0700 Subject: [PATCH v2 3/8] i2c: i2c-cortina: added CAxxxx I2C support In-Reply-To: <1584582738-22082-1-git-send-email-alex.nemirovsky@cortina-access.com> References: <1584582738-22082-1-git-send-email-alex.nemirovsky@cortina-access.com> Message-ID: <1584582738-22082-4-git-send-email-alex.nemirovsky@cortina-access.com> From: Arthur Li Add I2C controller support for Cortina Access CAxxxx SoCs Signed-off-by: Arthur Li Signed-off-by: Alex Nemirovsky --- Changes in v3: None Changes in v2: None MAINTAINERS | 4 + drivers/i2c/Kconfig | 7 + drivers/i2c/Makefile | 1 + drivers/i2c/i2c-cortina.c | 346 ++++++++++++++++++++++++++++++++++++++++++++++ drivers/i2c/i2c-cortina.h | 92 ++++++++++++ 5 files changed, 450 insertions(+) create mode 100644 drivers/i2c/i2c-cortina.c create mode 100644 drivers/i2c/i2c-cortina.h diff --git a/MAINTAINERS b/MAINTAINERS index bb45d3c..b147faa 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -181,6 +181,8 @@ F: drivers/gpio/cortina_gpio.c F: drivers/watchdog/cortina_wdt.c F: drivers/serial/serial_cortina.c F: drivers/mmc/ca_dw_mmc.c +F: drivers/i2c/i2c-cortina.c +F: drivers/i2c/i2c-cortina.h ARM/CZ.NIC TURRIS MOX SUPPORT M: Marek Behun @@ -672,6 +674,8 @@ F: drivers/gpio/cortina_gpio.c F: drivers/watchdog/cortina_wdt.c F: drivers/serial/serial_cortina.c F: drivers/mmc/ca_dw_mmc.c +F: drivers/i2c/i2c-cortina.c +F: drivers/i2c/i2c-cortina.h MIPS MSCC M: Gregory CLEMENT diff --git a/drivers/i2c/Kconfig b/drivers/i2c/Kconfig index 03d2fed..b98a4aa 100644 --- a/drivers/i2c/Kconfig +++ b/drivers/i2c/Kconfig @@ -85,6 +85,13 @@ config SYS_I2C_CADENCE Say yes here to select Cadence I2C Host Controller. This controller is e.g. used by Xilinx Zynq. +config SYS_I2C_CA + tristate "Cortina-Access I2C Controller" + depends on DM_I2C && CORTINA_PLATFORM + default n + help + Say yes here to select Cortina-Access I2C Host Controller. + config SYS_I2C_DAVINCI bool "Davinci I2C Controller" depends on (ARCH_KEYSTONE || ARCH_DAVINCI) diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile index f5a471f..5d18cf7 100644 --- a/drivers/i2c/Makefile +++ b/drivers/i2c/Makefile @@ -12,6 +12,7 @@ obj-$(CONFIG_SYS_I2C) += i2c_core.o obj-$(CONFIG_SYS_I2C_ASPEED) += ast_i2c.o obj-$(CONFIG_SYS_I2C_AT91) += at91_i2c.o obj-$(CONFIG_SYS_I2C_CADENCE) += i2c-cdns.o +obj-$(CONFIG_SYS_I2C_CA) += i2c-cortina.o obj-$(CONFIG_SYS_I2C_DAVINCI) += davinci_i2c.o obj-$(CONFIG_SYS_I2C_DW) += designware_i2c.o ifdef CONFIG_DM_PCI diff --git a/drivers/i2c/i2c-cortina.c b/drivers/i2c/i2c-cortina.c new file mode 100644 index 0000000..99c63f3 --- /dev/null +++ b/drivers/i2c/i2c-cortina.c @@ -0,0 +1,346 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * (C) Copyright 2020 + * Arthur Li, Cortina Access, arthur.li at cortina-access.com. + */ + +#include +#include +#include +#include +#include +#include "i2c-cortina.h" + +static void set_speed(struct i2c_regs *regs, int i2c_spd) +{ + union ca_biw_cfg i2c_cfg; + + i2c_cfg.wrd = readl(®s->i2c_cfg); + i2c_cfg.bf.core_en = 0; + writel(i2c_cfg.wrd, ®s->i2c_cfg); + + switch (i2c_spd) { + case IC_SPEED_MODE_MAX: + i2c_cfg.bf.prer = + CORTINA_PER_IO_FREQ / (5 * I2C_MAX_SPEED) - 1; + break; + + case IC_SPEED_MODE_STANDARD: + i2c_cfg.bf.prer = + CORTINA_PER_IO_FREQ / (5 * I2C_STANDARD_SPEED) - 1; + break; + + case IC_SPEED_MODE_FAST: + default: + i2c_cfg.bf.prer = + CORTINA_PER_IO_FREQ / (5 * I2C_FAST_SPEED) - 1; + break; + } + + i2c_cfg.bf.core_en = 1; + writel(i2c_cfg.wrd, ®s->i2c_cfg); +} + +static int ca_i2c_set_bus_speed(struct udevice *bus, unsigned int speed) +{ + struct ca_i2c *priv = dev_get_priv(bus); + int i2c_spd; + + if (speed >= I2C_MAX_SPEED) { + i2c_spd = IC_SPEED_MODE_MAX; + priv->speed = I2C_MAX_SPEED; + } else if (speed >= I2C_FAST_SPEED) { + i2c_spd = IC_SPEED_MODE_FAST; + priv->speed = I2C_FAST_SPEED; + } else { + i2c_spd = IC_SPEED_MODE_STANDARD; + priv->speed = I2C_STANDARD_SPEED; + } + + set_speed(priv->regs, i2c_spd); + + return 0; +} + +static int ca_i2c_get_bus_speed(struct udevice *bus) +{ + struct ca_i2c *priv = dev_get_priv(bus); + + return priv->speed; +} + +static void ca_i2c_init(struct i2c_regs *regs) +{ + union ca_biw_cfg i2c_cfg; + + i2c_cfg.wrd = readl(®s->i2c_cfg); + i2c_cfg.bf.core_en = 0; + i2c_cfg.bf.biw_soft_reset = 1; + writel(i2c_cfg.wrd, ®s->i2c_cfg); + mdelay(10); + i2c_cfg.bf.biw_soft_reset = 0; + writel(i2c_cfg.wrd, ®s->i2c_cfg); + + set_speed(regs, IC_SPEED_MODE_STANDARD); + + i2c_cfg.wrd = readl(®s->i2c_cfg); + i2c_cfg.bf.core_en = 1; + writel(i2c_cfg.wrd, ®s->i2c_cfg); +} + +static int i2c_wait_complete(struct i2c_regs *regs) +{ + union ca_biw_ctrl i2c_ctrl; + unsigned long start_time_bb = get_timer(0); + + i2c_ctrl.wrd = readl(®s->i2c_ctrl); + + while (i2c_ctrl.bf.biwdone == 0) { + i2c_ctrl.wrd = readl(®s->i2c_ctrl); + + if (get_timer(start_time_bb) > + (unsigned long)(I2C_BYTE_TO_BB)) { + printf("%s not done!!!\n", __func__); + return 1; + } + } + + /* Clear done bit */ + writel(i2c_ctrl.wrd, ®s->i2c_ctrl); + + return 0; +} + +static void i2c_setaddress(struct i2c_regs *regs, unsigned int i2c_addr, + int write_read) +{ + writel(i2c_addr | write_read, ®s->i2c_txr); + + writel(BIW_CTRL_START | BIW_CTRL_WRITE, + ®s->i2c_ctrl); + + i2c_wait_complete(regs); +} + +static int i2c_wait_for_bus_busy(struct i2c_regs *regs) +{ + union ca_biw_ack i2c_ack; + unsigned long start_time_bb = get_timer(0); + + i2c_ack.wrd = readl(®s->i2c_ack); + + while (i2c_ack.bf.biw_busy) { + i2c_ack.wrd = readl(®s->i2c_ack); + + if (get_timer(start_time_bb) > + (unsigned long)(I2C_BYTE_TO_BB)) { + printf("%s: timeout!\n", __func__); + return 1; + } + } + + return 0; +} + +static int i2c_xfer_init(struct i2c_regs *regs, uint8_t chip, uint addr, + int alen, int write_read) +{ + int addr_len = alen; + + if (i2c_wait_for_bus_busy(regs)) + return 1; + /* First cycle must write addr + offset */ + chip = ((chip & 0x7F) << 1); + if (alen == 0 && write_read == I2C_CMD_RD) + i2c_setaddress(regs, chip, I2C_CMD_RD); + else + i2c_setaddress(regs, chip, I2C_CMD_WT); + + while (alen) { + alen--; + writel(addr, ®s->i2c_txr); + if (write_read == I2C_CMD_RD) + writel(BIW_CTRL_WRITE | BIW_CTRL_STOP, + ®s->i2c_ctrl); + else + writel(BIW_CTRL_WRITE, ®s->i2c_ctrl); + i2c_wait_complete(regs); + } + + /* Send address again with Read flag if it's read command */ + if (write_read == I2C_CMD_RD && addr_len > 0) + i2c_setaddress(regs, chip, I2C_CMD_RD); + + return 0; +} + +static int i2c_xfer_finish(struct i2c_regs *regs) +{ + /* Dummy read makes bus free */ + writel(BIW_CTRL_READ | BIW_CTRL_STOP, ®s->i2c_ctrl); + i2c_wait_complete(regs); + + if (i2c_wait_for_bus_busy(regs)) { + printf("Timed out waiting for bus\n"); + return 1; + } + + return 0; +} + +static int ca_i2c_read(struct i2c_regs *regs, uint8_t chip, uint addr, + int alen, uint8_t *buffer, int len) +{ + unsigned long start_time_rx; + int rc = 0; + + if (i2c_xfer_init(regs, chip, addr, alen, I2C_CMD_RD)) + return 1; + + start_time_rx = get_timer(0); + while (len) { + /* ACK_IN is ack value to send during read. + * ack high only on the very last byte! + */ + if (len == 1) { + writel(BIW_CTRL_READ | BIW_CTRL_ACK_IN | BIW_CTRL_STOP, + ®s->i2c_ctrl); + } else { + writel(BIW_CTRL_READ, ®s->i2c_ctrl); + } + + rc = i2c_wait_complete(regs); + udelay(1); + + if (rc == 0) { + *buffer++ = + (uchar) readl(®s->i2c_rxr); + len--; + start_time_rx = get_timer(0); + + } else if (get_timer(start_time_rx) > I2C_BYTE_TO) { + return 1; + } + } + i2c_xfer_finish(regs); + return rc; +} + +static int ca_i2c_write(struct i2c_regs *regs, uint8_t chip, uint addr, + int alen, uint8_t *buffer, int len) +{ + int rc, nb = len; + unsigned long start_time_tx; + + if (i2c_xfer_init(regs, chip, addr, alen, I2C_CMD_WT)) + return 1; + + start_time_tx = get_timer(0); + while (len) { + writel(*buffer, ®s->i2c_txr); + if (len == 1) { + writel(BIW_CTRL_WRITE | BIW_CTRL_STOP, + ®s->i2c_ctrl); + } else { + writel(BIW_CTRL_WRITE, ®s->i2c_ctrl); + } + + rc = i2c_wait_complete(regs); + + if (rc == 0) { + len--; + buffer++; + start_time_tx = get_timer(0); + } else if (get_timer(start_time_tx) > (nb * I2C_BYTE_TO)) { + printf("Timed out. i2c write Failed\n"); + return 1; + } + } + + return 0; +} + +static int ca_i2c_probe_chip(struct udevice *bus, uint chip_addr, + uint chip_flags) +{ + struct ca_i2c *priv = dev_get_priv(bus); + int ret; + u32 tmp; + + /* Try to read the first location of the chip */ + ret = ca_i2c_read(priv->regs, chip_addr, 0, 1, (uchar *)&tmp, 1); + if (ret) + ca_i2c_init(priv->regs); + + return ret; +} + +static int ca_i2c_xfer(struct udevice *bus, struct i2c_msg *msg, int nmsgs) +{ + struct ca_i2c *priv = dev_get_priv(bus); + int ret; + + debug("i2c_xfer: %d messages\n", nmsgs); + for (; nmsgs > 0; nmsgs--, msg++) { + debug("i2c_xfer: chip=0x%x, len=0x%x\n", msg->addr, msg->len); + if (msg->flags & I2C_M_RD) { + ret = ca_i2c_read(priv->regs, msg->addr, 0, 0, + msg->buf, msg->len); + } else { + ret = ca_i2c_write(priv->regs, msg->addr, 0, 0, + msg->buf, msg->len); + } + + if (ret) { + debug("i2c_write: error sending\n"); + return -EREMOTEIO; + } + } + + return 0; +} + +static const struct dm_i2c_ops ca_i2c_ops = { + .xfer = ca_i2c_xfer, + .probe_chip = ca_i2c_probe_chip, + .set_bus_speed = ca_i2c_set_bus_speed, + .get_bus_speed = ca_i2c_get_bus_speed, +}; + +static const struct udevice_id ca_i2c_ids[] = { + { .compatible = "cortina,ca-i2c", }, + { } +}; + +static int ca_i2c_probe(struct udevice *bus) +{ + struct ca_i2c *priv = dev_get_priv(bus); + + ca_i2c_init(priv->regs); + + return 0; +} + +static int ca_i2c_ofdata_to_platdata(struct udevice *bus) +{ + struct ca_i2c *priv = dev_get_priv(bus); + + priv->regs = map_sysmem(dev_read_addr(bus), sizeof(struct i2c_regs)); + if (!priv->regs) { + printf("I2C: base address is invalid\n"); + return -EINVAL; + } + + return 0; +} + +U_BOOT_DRIVER(i2c_cortina) = { + .name = "i2c_cortina", + .id = UCLASS_I2C, + .of_match = ca_i2c_ids, + .ofdata_to_platdata = ca_i2c_ofdata_to_platdata, + .probe = ca_i2c_probe, + .priv_auto_alloc_size = sizeof(struct ca_i2c), + .ops = &ca_i2c_ops, + .flags = DM_FLAG_PRE_RELOC, +}; diff --git a/drivers/i2c/i2c-cortina.h b/drivers/i2c/i2c-cortina.h new file mode 100644 index 0000000..f1c3dc7 --- /dev/null +++ b/drivers/i2c/i2c-cortina.h @@ -0,0 +1,92 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * (C) Copyright 2019 + * Cortina Access, + */ + +#ifndef __CA_I2C_H_ +#define __CA_I2C_H_ + +#if !defined(__ASSEMBLER__) && !defined(__ASSEMBLY__) +struct i2c_regs { + u32 i2c_cfg; + u32 i2c_ctrl; + u32 i2c_txr; + u32 i2c_rxr; + u32 i2c_ack; + u32 i2c_ie0; + u32 i2c_int0; + u32 i2c_ie1; + u32 i2c_int1; + u32 i2c_stat; +}; + +union ca_biw_cfg { + struct biw_cfg { + u32 core_en : 1; + u32 biw_soft_reset : 1; + u32 busywait_en : 1; + u32 stretch_en : 1; + u32 arb_en : 1; + u32 clksync_en : 1; + u32 rsrvd1 : 2; + u32 spike_cnt : 4; + u32 rsrvd2 : 4; + u32 prer : 16; + } bf; + unsigned int wrd; +}; + +union ca_biw_ctrl { + struct biw_ctrl { + u32 biwdone : 1; + u32 rsrvd1 : 2; + u32 ack_in : 1; + u32 write : 1; + u32 read : 1; + u32 stop : 1; + u32 start : 1; + u32 rsrvd2 : 24; + } bf; + unsigned int wrd; +}; + +union ca_biw_ack { + struct biw_ack { + u32 al :1; + u32 biw_busy :1; + u32 ack_out :1; + u32 rsrvd1 :29; + } bf; + unsigned int wrd; +}; +#endif /* !__ASSEMBLER__*/ + +struct ca_i2c { + struct i2c_regs *regs; + unsigned int speed; +}; + +#define I2C_CMD_WT 0 +#define I2C_CMD_RD 1 + +#define BIW_CTRL_DONE BIT(0) +#define BIW_CTRL_ACK_IN BIT(3) +#define BIW_CTRL_WRITE BIT(4) +#define BIW_CTRL_READ BIT(5) +#define BIW_CTRL_STOP BIT(6) +#define BIW_CTRL_START BIT(7) + +#define I2C_BYTE_TO (CONFIG_SYS_HZ / 500) +#define I2C_STOPDET_TO (CONFIG_SYS_HZ / 500) +#define I2C_BYTE_TO_BB (10) + +#define IC_SPEED_MODE_STANDARD 1 +#define IC_SPEED_MODE_FAST 2 +#define IC_SPEED_MODE_MAX 3 + +#define I2C_MAX_SPEED 1000000 +#define I2C_FAST_SPEED 400000 +#define I2C_STANDARD_SPEED 100000 + +#endif /* __CA_I2C_H_ */