From patchwork Mon Jan 20 09:53:47 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Alex Nemirovsky X-Patchwork-Id: 239793 List-Id: U-Boot discussion From: Alex.Nemirovsky at cortina-access.com (Alex Nemirovsky) Date: Mon, 20 Jan 2020 09:53:47 +0000 Subject: [PATCH 4/4] serial: serial_cortina: add UART DM driver for CAxxxx SoCs In-Reply-To: <1579513995-1822-1-git-send-email-alex.nemirovsky@cortina-access.com> References: <1579513995-1822-1-git-send-email-alex.nemirovsky@cortina-access.com> Message-ID: <1579513995-1822-5-git-send-email-alex.nemirovsky@cortina-access.com> From: Jason Li Add serial UART driver support for all Cortina Access CAxxxx family of SoCs. Signed-off-by: Jason Li Signed-off-by: Alex Nemirovsky --- MAINTAINERS | 4 ++ drivers/serial/Kconfig | 7 +++ drivers/serial/Makefile | 2 +- drivers/serial/serial_cortina.c | 129 ++++++++++++++++++++++++++++++++++++++++ drivers/serial/serial_cortina.h | 83 ++++++++++++++++++++++++++ 5 files changed, 224 insertions(+), 1 deletion(-) create mode 100644 drivers/serial/serial_cortina.c create mode 100644 drivers/serial/serial_cortina.h diff --git a/MAINTAINERS b/MAINTAINERS index f9334f9..2b3282b 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -181,6 +181,8 @@ F: board/cortina/common/Kconfig F: board/cortina/common/armv8/lowlevel_init.S F: drivers/gpio/cortina_gpio.c F: drivers/watchdog/cortina_wdt.c +F: drivers/serial/serial_cortina.c +F: drivers/serial/serial_cortina.h ARM/CZ.NIC TURRIS MOX SUPPORT M: Marek Behun @@ -664,6 +666,8 @@ F: board/cortina/common/Kconfig F: board/cortina/common/mips/* F: drivers/gpio/cortina_gpio.c F: drivers/watchdog/cortina_wdt.c +F: drivers/serial/serial_cortina.c +F: drivers/serial/serial_cortina.h MIPS MSCC M: Gregory CLEMENT diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index ece7d87..9f76596 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -539,6 +539,13 @@ config BCM6345_SERIAL help Select this to enable UART on BCM6345 SoCs. +config CORTINA_UART + bool "Cortina UART support" + depends on DM_SERIAL + help + Select this to enable UART support for Cortina-Access UART devices + found on CAxxxx SoCs. + config FSL_LINFLEXUART bool "Freescale Linflex UART support" depends on DM_SERIAL diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile index 06ee306..c8f2db4 100644 --- a/drivers/serial/Makefile +++ b/drivers/serial/Makefile @@ -28,13 +28,13 @@ obj-$(CONFIG_PL010_SERIAL) += serial_pl01x.o obj-$(CONFIG_PL011_SERIAL) += serial_pl01x.o obj-$(CONFIG_SYS_NS16550_SERIAL) += serial_ns16550.o endif - obj-$(CONFIG_ALTERA_UART) += altera_uart.o obj-$(CONFIG_ALTERA_JTAG_UART) += altera_jtag_uart.o obj-$(CONFIG_AR933X_UART) += serial_ar933x.o obj-$(CONFIG_ARM_DCC) += arm_dcc.o obj-$(CONFIG_ATMEL_USART) += atmel_usart.o obj-$(CONFIG_BCM6345_SERIAL) += serial_bcm6345.o +obj-$(CONFIG_CORTINA_UART) += serial_cortina.o obj-$(CONFIG_EFI_APP) += serial_efi.o obj-$(CONFIG_LPC32XX_HSUART) += lpc32xx_hsuart.o obj-$(CONFIG_MCFUART) += mcfuart.o diff --git a/drivers/serial/serial_cortina.c b/drivers/serial/serial_cortina.c new file mode 100644 index 0000000..2b52e5d --- /dev/null +++ b/drivers/serial/serial_cortina.c @@ -0,0 +1,129 @@ +// SPDX-License-Identifier: GPL-2.0+ + +/* + * (C) Copyright 2020 + * Cortina-Access Ltd. + * Author: Jason Li + * + */ + +/* Common UART Driver for Cortina Access CAxxxx line of SoCs */ + +#include +#include +#include +#include +#include +#include +#include +#include "serial_cortina.h" + +#define IO_WRITE(addr, val) (*(unsigned int *)(addr) = (val)) +#define IO_READ(addr) (*(unsigned int *)(addr)) + +#ifdef CONFIG_DM_SERIAL + +struct ca_uart_priv { + void __iomem *base; +}; + +int ca_serial_setbrg(struct udevice *dev, int baudrate) +{ + struct ca_uart_priv *priv = dev_get_priv(dev); + unsigned int uart_ctrl, baud, sample; + + baud = CORTINA_UART_CLOCK / baudrate; + + uart_ctrl = readl(priv->base + UCFG); + uart_ctrl |= (baud << 8); + writel(uart_ctrl, priv->base + UCFG); + + sample = baud / 2; + sample = (sample < 7) ? 7 : sample; + writel(sample, priv->base + URX_SAMPLE); + + return 0; +} + +static int ca_serial_getc(struct udevice *dev) +{ + struct ca_uart_priv *priv = dev_get_priv(dev); + int ch; + + ch = readl(priv->base + URX_DATA) & 0xFF; + + return (int)ch; +} + +static int ca_serial_putc(struct udevice *dev, const char ch) +{ + struct ca_uart_priv *priv = dev_get_priv(dev); + unsigned int status; + + /* Retry if TX FIFO full */ + status = readl(priv->base + UINFO); + while (status & UINFO_TX_FIFO_FULL) + status = readl(priv->base + UINFO); + + writel(ch, priv->base + UTX_DATA); + + return 0; +} + +static int ca_serial_pending(struct udevice *dev, bool input) +{ + struct ca_uart_priv *priv = dev_get_priv(dev); + unsigned int status; + + status = readl(priv->base + UINFO); + + if (status & UINFO_RX_FIFO_EMPTY) /* empty */ + return 0; + else /* something in RX FIFO */ + return 1; +} + +static int ca_serial_probe(struct udevice *dev) +{ + struct ca_uart_priv *priv = dev_get_priv(dev); + u32 uart_ctrl; + + /* Set data, parity and stop bits */ + uart_ctrl = UCFG_EN | UCFG_TX_EN | UCFG_RX_EN | UCFG_CHAR_8; + writel(uart_ctrl, priv->base + UCFG); + + return 0; +} + +static int ca_serial_ofdata_to_platdata(struct udevice *dev) +{ + struct ca_uart_priv *priv = dev_get_priv(dev); + fdt_addr_t addr; + + addr = dev_read_addr(dev); + if (addr == FDT_ADDR_T_NONE) + return -EINVAL; + priv->base = map_physmem(addr, 0, MAP_NOCACHE); + + return 0; +} + +static const struct dm_serial_ops ca_serial_ops = { + .putc = ca_serial_putc, + .pending = ca_serial_pending, + .getc = ca_serial_getc, + .setbrg = ca_serial_setbrg, +}; + +static const struct udevice_id ca_serial_ids[] = { + {.compatible = "cortina,ca-uart"}, + {} +}; + +U_BOOT_DRIVER(serial_cortina) = { +.name = "serial_cortina", .id = UCLASS_SERIAL, .of_match = + ca_serial_ids, .ofdata_to_platdata = + ca_serial_ofdata_to_platdata, .priv_auto_alloc_size = + sizeof(struct ca_uart_priv), .probe = ca_serial_probe, .ops = + &ca_serial_ops,}; +#endif /* CONFIG_DM_SERIAL */ diff --git a/drivers/serial/serial_cortina.h b/drivers/serial/serial_cortina.h new file mode 100644 index 0000000..19448f2 --- /dev/null +++ b/drivers/serial/serial_cortina.h @@ -0,0 +1,83 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * u-boot/drivers/serial/serial_cortina.h + * + * Copyright (c) Cortina-Systems Limited 2020. All rights reserved. + * Jason Li + * + */ + +#ifndef _SERIAL_CORTINA_H_ +#define _SERIAL_CORTINA_H_ + +/* + * UART Module for Cortina Access CAxxxx line of SoCs + */ +#define UART0_BASE_ADDR CONFIG_SYS_SERIAL0 +#define UART1_BASE_ADDR CONFIG_SYS_SERIAL1 + +#define CONFIG_CONS_INDEX 0 + +/* Register definitions */ +#define UCFG 0x00 /* UART config register */ +#define UFC 0x04 /* Flow Control */ +#define URX_SAMPLE 0x08 /* UART RX Sample register */ +#define URT_TUNE 0x0C /* Fine tune of UART clk */ +#define UTX_DATA 0x10 /* UART TX Character data */ +#define URX_DATA 0x14 /* UART RX Character data */ +#define UINFO 0x18 /* UART Info */ +#define UINT_EN0 0x1C /* UART Interrupt enable 0*/ +#define UINT_EN1 0x20 /* UART Interrupt enable 1*/ +#define UINT0 0x24 /* UART Interrupt 0 setting/clearing */ +#define UINT1 0x28 /* UART Interrupt 1 setting/clearing */ +#define UINT_STAT 0x2C /* UART Interrupt Status */ + +/* UART Control Register Bit Fields */ +#define UCFG_BAUD_COUNT BIT(8) +#define UCFG_EN BIT(7) +#define UCFG_RX_EN BIT(6) +#define UCFG_TX_EN BIT(5) +#define UCFG_PARITY_EN BIT(4) +#define UCFG_PARITY_SEL BIT(3) +#define UCFG_2STOP_BIT BIT(2) +#define UCFG_CNT1 BIT(1) +#define UCFG_CNT0 BIT(0) +#define UCFG_CHAR_5 0 +#define UCFG_CHAR_6 1 +#define UCFG_CHAR_7 2 +#define UCFG_CHAR_8 3 + +#define UINFO_TX_FIFO_EMPTY BIT(3) +#define UINFO_TX_FIFO_FULL BIT(2) +#define UINFO_RX_FIFO_EMPTY BIT(1) +#define UINFO_RX_FIFO_FULL BIT(0) + +#define UINT_RX_NON_EMPTY BIT(6) +#define UINT_TX_EMPTY BIT(5) +#define UINT_RX_UNDERRUN BIT(4) +#define UINT_RX_OVERRUN BIT(3) +#define UINT_RX_PARITY_ERR BIT(2) +#define UINT_RX_STOP_ERR BIT(1) +#define UINT_TX_OVERRUN BIT(0) +#define UINT_MASK_ALL 0x7F + +/* UART CONF bits */ +#define SHF_UCONF_WL 0 +#define MSK_UCONF_WL (0x3 << SHF_UCONF_WL) +#define VAL_UCONF_WL_5 (0x0 << SHF_UCONF_WL) +#define VAL_UCONF_WL_6 (0x1 << SHF_UCONF_WL) +#define VAL_UCONF_WL_7 (0x2 << SHF_UCONF_WL) +#define VAL_UCONF_WL_8 (0x3 << SHF_UCONF_WL) + +#define SHF_UCONF_SB 2 +#define MSK_UCONF_SB (0x1 << SHF_UCONF_SB) +#define VAL_UCONF_SB_1 (0x0 << SHF_UCONF_SB) +#define VAL_UCONF_SB_2 (0x1 << SHF_UCONF_SB) + +#define SHF_UCONF_PM 3 +#define MSK_UCONF_PM (0x3 << SHF_UCONF_PM) +#define VAL_UCONF_PM_N (0x0 << SHF_UCONF_PM) +#define VAL_UCONF_PM_O (0x2 << SHF_UCONF_PM) +#define VAL_UCONF_PM_E (0x3 << SHF_UCONF_PM) + +#endif /* _SERIAL_CORTINA_H_ */