diff --git a/arch/arm/cpu/armv7/exynos/clock.c b/arch/arm/cpu/armv7/exynos/clock.c
index 0cb1a61..37bc65e 100644
--- a/arch/arm/cpu/armv7/exynos/clock.c
+++ b/arch/arm/cpu/armv7/exynos/clock.c
@@ -96,7 +96,7 @@ static int exynos_get_pll_clk(int pllreg, unsigned int r, unsigned int k)
 
 	freq = CONFIG_SYS_CLK_FREQ;
 
-	if (pllreg == EPLL) {
+	if (pllreg == EPLL || pllreg == RPLL) {
 		k = k & 0xffff;
 		/* FOUT = (MDIV + K / 65536) * FIN / (PDIV * 2^SDIV) */
 		fout = (m + k / PLL_DIV_65536) * (freq / (p * (1 << s)));
@@ -117,7 +117,7 @@ static int exynos_get_pll_clk(int pllreg, unsigned int r, unsigned int k)
 			div = PLL_DIV_1024;
 		else if (proid_is_exynos4412())
 			div = PLL_DIV_65535;
-		else if (proid_is_exynos5250())
+		else if (cpu_is_exynos5())
 			div = PLL_DIV_65536;
 		else
 			return 0;
@@ -359,6 +359,43 @@ unsigned long clock_get_periph_rate(int peripheral)
 		return 0;
 }
 
+/* exynos5420: return pll clock frequency */
+static unsigned long exynos5420_get_pll_clk(int pllreg)
+{
+	struct exynos5420_clock *clk =
+		(struct exynos5420_clock *)samsung_get_base_clock();
+	unsigned long r, k = 0;
+
+	switch (pllreg) {
+	case APLL:
+		r = readl(&clk->apll_con0);
+		break;
+	case MPLL:
+		r = readl(&clk->mpll_con0);
+		break;
+	case EPLL:
+		r = readl(&clk->epll_con0);
+		k = readl(&clk->epll_con1);
+		break;
+	case VPLL:
+		r = readl(&clk->vpll_con0);
+		k = readl(&clk->vpll_con1);
+		break;
+	case BPLL:
+		r = readl(&clk->bpll_con0);
+		break;
+	case RPLL:
+		r = readl(&clk->rpll_con0);
+		k = readl(&clk->rpll_con1);
+		break;
+	default:
+		printf("Unsupported PLL (%d)\n", pllreg);
+		return 0;
+	}
+
+	return exynos_get_pll_clk(pllreg, r, k);
+}
+
 /* exynos4: return ARM clock frequency */
 static unsigned long exynos4_get_arm_clk(void)
 {
@@ -482,6 +519,27 @@ static unsigned long exynos4x12_get_pwm_clk(void)
 	return pclk;
 }
 
+/* exynos5420: return pwm clock frequency */
+static unsigned long exynos5420_get_pwm_clk(void)
+{
+	struct exynos5420_clock *clk =
+		(struct exynos5420_clock *)samsung_get_base_clock();
+	unsigned long pclk, sclk;
+	unsigned int ratio;
+
+	/*
+	 * CLK_DIV_PERIC3
+	 * PWM_RATIO [3:0]
+	 */
+	ratio = readl(&clk->div_peric0);
+	ratio = (ratio >> 28) & 0xf;
+	sclk = get_pll_clk(MPLL);
+
+	pclk = sclk / (ratio + 1);
+
+	return pclk;
+}
+
 /* exynos4: return uart clock frequency */
 static unsigned long exynos4_get_uart_clk(int dev_index)
 {
@@ -621,6 +679,53 @@ static unsigned long exynos5_get_uart_clk(int dev_index)
 	return uclk;
 }
 
+/* exynos5420: return uart clock frequency */
+static unsigned long exynos5420_get_uart_clk(int dev_index)
+{
+	struct exynos5420_clock *clk =
+		(struct exynos5420_clock *)samsung_get_base_clock();
+	unsigned long uclk, sclk;
+	unsigned int sel;
+	unsigned int ratio;
+
+	/*
+	 * CLK_SRC_PERIC0
+	 * UART0_SEL [3:0]
+	 * UART1_SEL [7:4]
+	 * UART2_SEL [8:11]
+	 * UART3_SEL [12:15]
+	 * UART4_SEL [16:19]
+	 * UART5_SEL [23:20]
+	 */
+	sel = readl(&clk->src_peric0);
+	sel = (sel >> ((dev_index * 4) + 4)) & 0x7;
+
+	if (sel == 0x3)
+		sclk = get_pll_clk(MPLL);
+	else if (sel == 0x6)
+		sclk = get_pll_clk(EPLL);
+	else if (sel == 0x7)
+		sclk = get_pll_clk(RPLL);
+	else
+		return 0;
+
+	/*
+	 * CLK_DIV_PERIC0
+	 * UART0_RATIO [3:0]
+	 * UART1_RATIO [7:4]
+	 * UART2_RATIO [8:11]
+	 * UART3_RATIO [12:15]
+	 * UART4_RATIO [16:19]
+	 * UART5_RATIO [23:20]
+	 */
+	ratio = readl(&clk->div_peric0);
+	ratio = (ratio >> ((dev_index * 4) + 8)) & 0xf;
+
+	uclk = sclk / (ratio + 1);
+
+	return uclk;
+}
+
 static unsigned long exynos4_get_mmc_clk(int dev_index)
 {
 	struct exynos4_clock *clk =
@@ -715,6 +820,34 @@ static unsigned long exynos5_get_mmc_clk(int dev_index)
 	return uclk;
 }
 
+static unsigned long exynos5420_get_mmc_clk(int dev_index)
+{
+	struct exynos5420_clock *clk =
+		(struct exynos5420_clock *)samsung_get_base_clock();
+	unsigned long uclk, sclk;
+	unsigned int sel, ratio;
+	int shift = 0;
+
+	sel = readl(&clk->src_fsys);
+	sel = (sel >> ((dev_index * 4) + 8)) & 0x7;
+
+	if (sel == 0x3)
+		sclk = get_pll_clk(MPLL);
+	else if (sel == 0x6)
+		sclk = get_pll_clk(EPLL);
+	else
+		return 0;
+
+	ratio = readl(&clk->div_fsys1);
+
+	shift = dev_index * 10;
+
+	ratio = (ratio >> shift) & 0x3ff;
+	uclk = (sclk / (ratio + 1));
+
+	return uclk;
+}
+
 /* exynos4: set the mmc clock */
 static void exynos4_set_mmc_clk(int dev_index, unsigned int div)
 {
@@ -801,6 +934,23 @@ static void exynos5_set_mmc_clk(int dev_index, unsigned int div)
 	writel(val, addr);
 }
 
+/* exynos5: set the mmc clock */
+static void exynos5420_set_mmc_clk(int dev_index, unsigned int div)
+{
+	struct exynos5420_clock *clk =
+		(struct exynos5420_clock *)samsung_get_base_clock();
+	unsigned int addr;
+	unsigned int val, shift;
+
+	addr = (unsigned int)&clk->div_fsys1;
+	shift = dev_index * 10;
+
+	val = readl(addr);
+	val &= ~(0x3ff << shift);
+	val |= (div & 0x3ff) << shift;
+	writel(val, addr);
+}
+
 /* get_lcd_clk: return lcd clock frequency */
 static unsigned long exynos4_get_lcd_clk(void)
 {
@@ -1295,6 +1445,84 @@ static int exynos5_set_spi_clk(enum periph_id periph_id,
 	return 0;
 }
 
+static int exynos5420_set_spi_clk(enum periph_id periph_id,
+					unsigned int rate)
+{
+	struct exynos5420_clock *clk =
+		(struct exynos5420_clock *)samsung_get_base_clock();
+	int main;
+	unsigned int fine, val;
+	unsigned shift, pre_shift;
+	unsigned div_mask = 0xf, pre_div_mask = 0xff;
+
+	main = clock_calc_best_scalar(4, 8, 400000000, rate, &fine);
+	if (main < 0) {
+		debug("%s: Cannot set clock rate for periph %d",
+		      __func__, periph_id);
+		return -1;
+	}
+	main = main - 1;
+	fine = fine - 1;
+
+	switch (periph_id) {
+	case PERIPH_ID_SPI0:
+		val = readl(&clk->div_peric1);
+		val &= ~(div_mask << 20);
+		val |= (main << 20);
+		writel(val, &clk->div_peric1);
+
+		val = readl(&clk->div_peric4);
+		val &= ~(pre_div_mask << 8);
+		val |= (fine << 8);
+		writel(val, &clk->div_peric4);
+		break;
+	case PERIPH_ID_SPI1:
+		val = readl(&clk->div_peric1);
+		val &= ~(div_mask << 24);
+		val |= (main << 24);
+		writel(val, &clk->div_peric1);
+
+		val = readl(&clk->div_peric4);
+		val &= ~(pre_div_mask << 16);
+		val |= (fine << 16);
+		writel(val, &clk->div_peric4);
+		break;
+	case PERIPH_ID_SPI2:
+		val = readl(&clk->div_peric1);
+		val &= ~(div_mask << 28);
+		val |= (main << 28);
+		writel(val, &clk->div_peric1);
+
+		val = readl(&clk->div_peric4);
+		val &= ~(pre_div_mask << 24);
+		val |= (fine << 24);
+		writel(val, &clk->div_peric4);
+		break;
+	case PERIPH_ID_SPI3:
+		shift = 16;
+		pre_shift = 0;
+		clrsetbits_le32(&clk->div_isp1, div_mask << shift,
+				(main & div_mask) << shift);
+		clrsetbits_le32(&clk->div_isp1, pre_div_mask << pre_shift,
+				(fine & pre_div_mask) << pre_shift);
+		break;
+	case PERIPH_ID_SPI4:
+		shift = 20;
+		pre_shift = 8;
+		clrsetbits_le32(&clk->div_isp1, div_mask << shift,
+				(main & div_mask) << shift);
+		clrsetbits_le32(&clk->div_isp1, pre_div_mask << pre_shift,
+				(fine & pre_div_mask) << pre_shift);
+		break;
+	default:
+		debug("%s: Unsupported peripheral ID %d\n", __func__,
+		      periph_id);
+		return -1;
+	}
+
+	return 0;
+}
+
 static unsigned long exynos4_get_i2c_clk(void)
 {
 	struct exynos4_clock *clk =
@@ -1312,9 +1540,11 @@ static unsigned long exynos4_get_i2c_clk(void)
 
 unsigned long get_pll_clk(int pllreg)
 {
-	if (cpu_is_exynos5())
+	if (cpu_is_exynos5()) {
+		if (proid_is_exynos5420())
+			return exynos5420_get_pll_clk(pllreg);
 		return exynos5_get_pll_clk(pllreg);
-	else {
+	} else {
 		if (proid_is_exynos4412())
 			return exynos4x12_get_pll_clk(pllreg);
 		return exynos4_get_pll_clk(pllreg);
@@ -1346,9 +1576,11 @@ unsigned long get_i2c_clk(void)
 
 unsigned long get_pwm_clk(void)
 {
-	if (cpu_is_exynos5())
+	if (cpu_is_exynos5()) {
+		if (proid_is_exynos5420())
+			return exynos5420_get_pwm_clk();
 		return clock_get_periph_rate(PERIPH_ID_PWM0);
-	else {
+	} else {
 		if (proid_is_exynos4412())
 			return exynos4x12_get_pwm_clk();
 		return exynos4_get_pwm_clk();
@@ -1357,9 +1589,11 @@ unsigned long get_pwm_clk(void)
 
 unsigned long get_uart_clk(int dev_index)
 {
-	if (cpu_is_exynos5())
+	if (cpu_is_exynos5()) {
+		if (proid_is_exynos5420())
+			return exynos5420_get_uart_clk(dev_index);
 		return exynos5_get_uart_clk(dev_index);
-	else {
+	} else {
 		if (proid_is_exynos4412())
 			return exynos4x12_get_uart_clk(dev_index);
 		return exynos4_get_uart_clk(dev_index);
@@ -1368,17 +1602,22 @@ unsigned long get_uart_clk(int dev_index)
 
 unsigned long get_mmc_clk(int dev_index)
 {
-	if (cpu_is_exynos5())
+	if (cpu_is_exynos5()) {
+		if (proid_is_exynos5420())
+			return exynos5420_get_mmc_clk(dev_index);
 		return exynos5_get_mmc_clk(dev_index);
-	else
+	} else {
 		return exynos4_get_mmc_clk(dev_index);
+	}
 }
 
 void set_mmc_clk(int dev_index, unsigned int div)
 {
-	if (cpu_is_exynos5())
+	if (cpu_is_exynos5()) {
+		if (proid_is_exynos5420())
+			return exynos5420_set_mmc_clk(dev_index, div);
 		exynos5_set_mmc_clk(dev_index, div);
-	else {
+	} else {
 		if (proid_is_exynos4412())
 			exynos4x12_set_mmc_clk(dev_index, div);
 		exynos4_set_mmc_clk(dev_index, div);
@@ -1409,10 +1648,13 @@ void set_mipi_clk(void)
 
 int set_spi_clk(int periph_id, unsigned int rate)
 {
-	if (cpu_is_exynos5())
+	if (cpu_is_exynos5()) {
+		if (proid_is_exynos5420())
+			return exynos5420_set_spi_clk(periph_id, rate);
 		return exynos5_set_spi_clk(periph_id, rate);
-	else
+	} else {
 		return 0;
+	}
 }
 
 int set_i2s_clk_prescaler(unsigned int src_frq, unsigned int dst_frq)
diff --git a/arch/arm/cpu/armv7/exynos/clock_init.h b/arch/arm/cpu/armv7/exynos/clock_init.h
index c28ff3a..a875d0b 100644
--- a/arch/arm/cpu/armv7/exynos/clock_init.h
+++ b/arch/arm/cpu/armv7/exynos/clock_init.h
@@ -10,7 +10,11 @@
 #define __EXYNOS_CLOCK_INIT_H
 
 enum {
+#ifdef CONFIG_EXYNOS5420
+	MEM_TIMINGS_MSR_COUNT	= 5,
+#else
 	MEM_TIMINGS_MSR_COUNT	= 4,
+#endif
 };
 
 /* These are the ratio's for configuring ARM clock */
@@ -59,6 +63,18 @@ struct mem_timings {
 	unsigned bpll_mdiv;
 	unsigned bpll_pdiv;
 	unsigned bpll_sdiv;
+	unsigned kpll_mdiv;
+	unsigned kpll_pdiv;
+	unsigned kpll_sdiv;
+	unsigned dpll_mdiv;
+	unsigned dpll_pdiv;
+	unsigned dpll_sdiv;
+	unsigned ipll_mdiv;
+	unsigned ipll_pdiv;
+	unsigned ipll_sdiv;
+	unsigned spll_mdiv;
+	unsigned spll_pdiv;
+	unsigned spll_sdiv;
 	unsigned pclk_cdrex_ratio;
 	unsigned direct_cmd_msr[MEM_TIMINGS_MSR_COUNT];
 
@@ -115,6 +131,7 @@ struct mem_timings {
 	uint8_t send_zq_init;		/* 1 to send this command */
 	unsigned impedance;		/* drive strength impedeance */
 	uint8_t gate_leveling_enable;	/* check gate leveling is enabled */
+	uint8_t read_leveling_enable;	/* check h/w read leveling is enabled */
 };
 
 /**
diff --git a/arch/arm/cpu/armv7/exynos/clock_init_exynos5.c b/arch/arm/cpu/armv7/exynos/clock_init_exynos5.c
index a24c2f3..9769173 100644
--- a/arch/arm/cpu/armv7/exynos/clock_init_exynos5.c
+++ b/arch/arm/cpu/armv7/exynos/clock_init_exynos5.c
@@ -24,6 +24,24 @@
 DECLARE_GLOBAL_DATA_PTR;
 
 struct arm_clk_ratios arm_clk_ratios[] = {
+#ifdef CONFIG_EXYNOS5420
+	{
+		.arm_freq_mhz = 900,
+
+		.apll_mdiv = 0x96,
+		.apll_pdiv = 0x2,
+		.apll_sdiv = 0x1,
+
+		.arm2_ratio = 0x0,
+		.apll_ratio = 0x3,
+		.pclk_dbg_ratio = 0x6,
+		.atb_ratio = 0x6,
+		.periph_ratio = 0x7,
+		.acp_ratio = 0x0,
+		.cpud_ratio = 0x2,
+		.arm_ratio = 0x0,
+	}
+#else
 	{
 		.arm_freq_mhz = 600,
 
@@ -115,8 +133,133 @@ struct arm_clk_ratios arm_clk_ratios[] = {
 		.cpud_ratio = 0x3,
 		.arm_ratio = 0x0,
 	}
+#endif
 };
+
 struct mem_timings mem_timings[] = {
+#ifdef CONFIG_EXYNOS5420
+	{
+		.mem_manuf = MEM_MANUF_SAMSUNG,
+		.mem_type = DDR_MODE_DDR3,
+		.frequency_mhz = 800,
+
+		/* MPLL @800MHz*/
+		.mpll_mdiv = 0xc8,
+		.mpll_pdiv = 0x3,
+		.mpll_sdiv = 0x1,
+		/* CPLL @666MHz */
+		.cpll_mdiv = 0xde,
+		.cpll_pdiv = 0x4,
+		.cpll_sdiv = 0x1,
+		/* EPLL @600MHz */
+		.epll_mdiv = 0x64,
+		.epll_pdiv = 0x2,
+		.epll_sdiv = 0x1,
+		/* VPLL @430MHz */
+		.vpll_mdiv = 0xd7,
+		.vpll_pdiv = 0x3,
+		.vpll_sdiv = 0x2,
+		/* BPLL @800MHz */
+		.bpll_mdiv = 0xc8,
+		.bpll_pdiv = 0x3,
+		.bpll_sdiv = 0x1,
+		/* KPLL @600MHz */
+		.kpll_mdiv = 0x190,
+		.kpll_pdiv = 0x4,
+		.kpll_sdiv = 0x2,
+		/* DPLL @600MHz */
+		.dpll_mdiv = 0x190,
+		.dpll_pdiv = 0x4,
+		.dpll_sdiv = 0x2,
+		/* IPLL @370MHz */
+		.ipll_mdiv = 0xb9,
+		.ipll_pdiv = 0x3,
+		.ipll_sdiv = 0x2,
+		/* SPLL @400MHz */
+		.spll_mdiv = 0xc8,
+		.spll_pdiv = 0x3,
+		.spll_sdiv = 0x2,
+
+		.direct_cmd_msr = {
+			0x00020018, 0x00030000, 0x00010046, 0x00000d70,
+			0x00000c70
+		},
+		.timing_ref = 0x000000bb,
+		.timing_row = 0x6836650f,
+		.timing_data = 0x3630580b,
+		.timing_power = 0x41000a26,
+		.phy0_dqs = 0x08080808,
+		.phy1_dqs = 0x08080808,
+		.phy0_dq = 0x08080808,
+		.phy1_dq = 0x08080808,
+		.phy0_tFS = 0x8,
+		.phy1_tFS = 0x8,
+		.phy0_pulld_dqs = 0xf,
+		.phy1_pulld_dqs = 0xf,
+
+		.lpddr3_ctrl_phy_reset = 0x1,
+		.ctrl_start_point = 0x10,
+		.ctrl_inc = 0x10,
+		.ctrl_start = 0x1,
+		.ctrl_dll_on = 0x1,
+		.ctrl_ref = 0x8,
+
+		.ctrl_force = 0x1a,
+		.ctrl_rdlat = 0x0b,
+		.ctrl_bstlen = 0x08,
+
+		.fp_resync = 0x8,
+		.iv_size = 0x7,
+		.dfi_init_start = 1,
+		.aref_en = 1,
+
+		.rd_fetch = 0x3,
+
+		.zq_mode_dds = 0x7,
+		.zq_mode_term = 0x1,
+		.zq_mode_noterm = 1,
+
+		/*
+		* Dynamic Clock: Always Running
+		* Memory Burst length: 8
+		* Number of chips: 1
+		* Memory Bus width: 32 bit
+		* Memory Type: DDR3
+		* Additional Latancy for PLL: 0 Cycle
+		*/
+		.memcontrol = DMC_MEMCONTROL_CLK_STOP_DISABLE |
+			DMC_MEMCONTROL_DPWRDN_DISABLE |
+			DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE |
+			DMC_MEMCONTROL_TP_DISABLE |
+			DMC_MEMCONTROL_DSREF_DISABLE |
+			DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(0) |
+			DMC_MEMCONTROL_MEM_TYPE_DDR3 |
+			DMC_MEMCONTROL_MEM_WIDTH_32BIT |
+			DMC_MEMCONTROL_NUM_CHIP_1 |
+			DMC_MEMCONTROL_BL_8 |
+			DMC_MEMCONTROL_PZQ_DISABLE |
+			DMC_MEMCONTROL_MRR_BYTE_7_0,
+		.memconfig = DMC_MEMCONFIG_CHIP_MAP_SPLIT |
+			DMC_MEMCONFIGX_CHIP_COL_10 |
+			DMC_MEMCONFIGX_CHIP_ROW_15 |
+			DMC_MEMCONFIGX_CHIP_BANK_8,
+		.prechconfig_tp_cnt = 0xff,
+		.dpwrdn_cyc = 0xff,
+		.dsref_cyc = 0xffff,
+		.concontrol = DMC_CONCONTROL_DFI_INIT_START_DISABLE |
+			DMC_CONCONTROL_TIMEOUT_LEVEL0 |
+			DMC_CONCONTROL_RD_FETCH_DISABLE |
+			DMC_CONCONTROL_EMPTY_DISABLE |
+			DMC_CONCONTROL_AREF_EN_DISABLE |
+			DMC_CONCONTROL_IO_PD_CON_DISABLE,
+		.dmc_channels = 1,
+		.chips_per_channel = 1,
+		.chips_to_configure = 1,
+		.send_zq_init = 1,
+		.gate_leveling_enable = 1,
+		.read_leveling_enable = 0,
+	}
+#else
 	{
 		.mem_manuf = MEM_MANUF_ELPIDA,
 		.mem_type = DDR_MODE_DDR3,
@@ -324,6 +467,7 @@ struct mem_timings mem_timings[] = {
 		.impedance = IMP_OUTPUT_DRV_40_OHM,
 		.gate_leveling_enable = 1,
 	}
+#endif
 };
 
 /**
@@ -399,7 +543,7 @@ struct mem_timings *clock_get_mem_timings(void)
 	return NULL;
 }
 
-void system_clock_init()
+static void exynos5250_system_clock_init(void)
 {
 	struct exynos5_clock *clk =
 		(struct exynos5_clock *)samsung_get_base_clock();
@@ -436,19 +580,13 @@ void system_clock_init()
 	} while ((val | MUX_BPLL_SEL_MASK) != val);
 
 	/* PLL locktime */
-	writel(APLL_LOCK_VAL, &clk->apll_lock);
-
-	writel(MPLL_LOCK_VAL, &clk->mpll_lock);
-
-	writel(BPLL_LOCK_VAL, &clk->bpll_lock);
-
-	writel(CPLL_LOCK_VAL, &clk->cpll_lock);
-
-	writel(GPLL_LOCK_VAL, &clk->gpll_lock);
-
-	writel(EPLL_LOCK_VAL, &clk->epll_lock);
-
-	writel(VPLL_LOCK_VAL, &clk->vpll_lock);
+	writel(mem->apll_pdiv * PLL_LOCK_FACTOR, &clk->apll_lock);
+	writel(mem->mpll_pdiv * PLL_LOCK_FACTOR, &clk->mpll_lock);
+	writel(mem->bpll_pdiv * PLL_LOCK_FACTOR, &clk->bpll_lock);
+	writel(mem->cpll_pdiv * PLL_LOCK_FACTOR, &clk->cpll_lock);
+	writel(mem->gpll_pdiv * PLL_X_LOCK_FACTOR, &clk->gpll_lock);
+	writel(mem->epll_pdiv * PLL_X_LOCK_FACTOR, &clk->epll_lock);
+	writel(mem->vpll_pdiv * PLL_X_LOCK_FACTOR, &clk->vpll_lock);
 
 	writel(CLK_REG_DISABLE, &clk->pll_div2_sel);
 
@@ -640,6 +778,189 @@ void system_clock_init()
 	writel(val, &clk->div_fsys2);
 }
 
+static void exynos5420_system_clock_init(void)
+{
+	struct exynos5420_clock *clk =
+		(struct exynos5420_clock *)EXYNOS5_CLOCK_BASE;
+	struct mem_timings *mem;
+	struct arm_clk_ratios *arm_clk_ratio;
+	u32 val;
+
+	mem = clock_get_mem_timings();
+	arm_clk_ratio = get_arm_ratios();
+
+	/* PLL locktime */
+	writel(arm_clk_ratio->apll_pdiv * PLL_LOCK_FACTOR, &clk->apll_lock);
+	writel(mem->mpll_pdiv * PLL_LOCK_FACTOR, &clk->mpll_lock);
+	writel(mem->bpll_pdiv * PLL_LOCK_FACTOR, &clk->bpll_lock);
+	writel(mem->cpll_pdiv * PLL_LOCK_FACTOR, &clk->cpll_lock);
+	writel(mem->dpll_pdiv * PLL_LOCK_FACTOR, &clk->dpll_lock);
+	writel(mem->epll_pdiv * PLL_X_LOCK_FACTOR, &clk->epll_lock);
+	writel(mem->vpll_pdiv * PLL_LOCK_FACTOR, &clk->vpll_lock);
+	writel(mem->ipll_pdiv * PLL_LOCK_FACTOR, &clk->ipll_lock);
+	writel(mem->spll_pdiv * PLL_LOCK_FACTOR, &clk->spll_lock);
+	writel(mem->kpll_pdiv * PLL_LOCK_FACTOR, &clk->kpll_lock);
+
+	setbits_le32(&clk->src_cpu, MUX_HPM_SEL_MASK);
+
+	writel(0, &clk->src_top6);
+
+	writel(0, &clk->src_cdrex);
+	writel(SRC_KFC_HPM_SEL, &clk->src_kfc);
+	writel(HPM_RATIO,  &clk->div_cpu1);
+	writel(CLK_DIV_CPU0_VAL,  &clk->div_cpu0);
+
+	/* switch A15 clock source to OSC clock before changing APLL */
+	clrbits_le32(&clk->src_cpu, APLL_FOUT);
+
+	/* Set APLL */
+	writel(APLL_CON1_VAL, &clk->apll_con1);
+	val = set_pll(arm_clk_ratio->apll_mdiv,
+		      arm_clk_ratio->apll_pdiv,
+		      arm_clk_ratio->apll_sdiv);
+	writel(val, &clk->apll_con0);
+	while ((readl(&clk->apll_con0) & PLL_LOCKED) == 0)
+		;
+
+	writel(SRC_KFC_HPM_SEL, &clk->src_kfc);
+	writel(CLK_DIV_KFC_VAL, &clk->div_kfc0);
+
+	/* switch A7 clock source to OSC clock before changing KPLL */
+	clrbits_le32(&clk->src_kfc, KPLL_FOUT);
+
+	/* Set KPLL*/
+	writel(KPLL_CON1_VAL, &clk->kpll_con1);
+	val = set_pll(mem->kpll_mdiv, mem->kpll_pdiv, mem->kpll_sdiv);
+	writel(val, &clk->kpll_con0);
+	while ((readl(&clk->kpll_con0) & PLL_LOCKED) == 0)
+		;
+
+	/* now it is safe to switch to KPLL */
+	setbits_le32(&clk->src_kfc, KPLL_FOUT);
+
+	/* Set MPLL */
+	writel(MPLL_CON1_VAL, &clk->mpll_con1);
+	val = set_pll(mem->mpll_mdiv, mem->mpll_pdiv, mem->mpll_sdiv);
+	writel(val, &clk->mpll_con0);
+	while ((readl(&clk->mpll_con0) & PLL_LOCKED) == 0)
+		;
+
+	/* Set DPLL */
+	writel(DPLL_CON1_VAL, &clk->dpll_con1);
+	val = set_pll(mem->dpll_mdiv, mem->dpll_pdiv, mem->dpll_sdiv);
+	writel(val, &clk->dpll_con0);
+	while ((readl(&clk->dpll_con0) & PLL_LOCKED) == 0)
+		;
+
+	/* Set EPLL */
+	writel(EPLL_CON2_VAL, &clk->epll_con2);
+	writel(EPLL_CON1_VAL, &clk->epll_con1);
+	val = set_pll(mem->epll_mdiv, mem->epll_pdiv, mem->epll_sdiv);
+	writel(val, &clk->epll_con0);
+	while ((readl(&clk->epll_con0) & PLL_LOCKED) == 0)
+		;
+
+	/* Set CPLL */
+	writel(CPLL_CON1_VAL, &clk->cpll_con1);
+	val = set_pll(mem->cpll_mdiv, mem->cpll_pdiv, mem->cpll_sdiv);
+	writel(val, &clk->cpll_con0);
+	while ((readl(&clk->cpll_con0) & PLL_LOCKED) == 0)
+		;
+
+	/* Set IPLL */
+	writel(IPLL_CON1_VAL, &clk->ipll_con1);
+	val = set_pll(mem->ipll_mdiv, mem->ipll_pdiv, mem->ipll_sdiv);
+	writel(val, &clk->ipll_con0);
+	while ((readl(&clk->ipll_con0) & PLL_LOCKED) == 0)
+		;
+
+	/* Set VPLL */
+	writel(VPLL_CON1_VAL, &clk->vpll_con1);
+	val = set_pll(mem->vpll_mdiv, mem->vpll_pdiv, mem->vpll_sdiv);
+	writel(val, &clk->vpll_con0);
+	while ((readl(&clk->vpll_con0) & PLL_LOCKED) == 0)
+		;
+
+	/* Set BPLL */
+	writel(BPLL_CON1_VAL, &clk->bpll_con1);
+	val = set_pll(mem->bpll_mdiv, mem->bpll_pdiv, mem->bpll_sdiv);
+	writel(val, &clk->bpll_con0);
+	while ((readl(&clk->bpll_con0) & PLL_LOCKED) == 0)
+		;
+
+	/* Set SPLL */
+	writel(SPLL_CON1_VAL, &clk->spll_con1);
+	val = set_pll(mem->spll_mdiv, mem->spll_pdiv, mem->spll_sdiv);
+	writel(val, &clk->spll_con0);
+	while ((readl(&clk->spll_con0) & PLL_LOCKED) == 0)
+		;
+
+	writel(CLK_DIV_CDREX0_VAL, &clk->div_cdrex0);
+	writel(CLK_DIV_CDREX1_VAL, &clk->div_cdrex1);
+
+	writel(CLK_SRC_TOP0_VAL, &clk->src_top0);
+	writel(CLK_SRC_TOP1_VAL, &clk->src_top1);
+	writel(CLK_SRC_TOP2_VAL, &clk->src_top2);
+	writel(CLK_SRC_TOP7_VAL, &clk->src_top7);
+
+	writel(CLK_DIV_TOP0_VAL, &clk->div_top0);
+	writel(CLK_DIV_TOP1_VAL, &clk->div_top1);
+	writel(CLK_DIV_TOP2_VAL, &clk->div_top2);
+
+	writel(0, &clk->src_top10);
+	writel(0, &clk->src_top11);
+	writel(0, &clk->src_top12);
+
+	writel(CLK_SRC_TOP3_VAL, &clk->src_top3);
+	writel(CLK_SRC_TOP4_VAL, &clk->src_top4);
+	writel(CLK_SRC_TOP5_VAL, &clk->src_top5);
+
+	/* DISP1 BLK CLK SELECTION */
+	writel(CLK_SRC_DISP1_0_VAL, &clk->src_disp10);
+	writel(CLK_DIV_DISP1_0_VAL, &clk->div_disp10);
+
+	/* AUDIO BLK */
+	writel(AUDIO0_SEL_EPLL, &clk->src_mau);
+	writel(DIV_MAU_VAL, &clk->div_mau);
+
+	/* FSYS */
+	writel(CLK_SRC_FSYS0_VAL, &clk->src_fsys);
+	writel(CLK_DIV_FSYS0_VAL, &clk->div_fsys0);
+	writel(CLK_DIV_FSYS1_VAL, &clk->div_fsys1);
+	writel(CLK_DIV_FSYS2_VAL, &clk->div_fsys2);
+
+	writel(CLK_SRC_ISP_VAL, &clk->src_isp);
+	writel(CLK_DIV_ISP0_VAL, &clk->div_isp0);
+	writel(CLK_DIV_ISP1_VAL, &clk->div_isp1);
+
+	writel(CLK_SRC_PERIC0_VAL, &clk->src_peric0);
+	writel(CLK_SRC_PERIC1_VAL, &clk->src_peric1);
+
+	writel(CLK_DIV_PERIC0_VAL, &clk->div_peric0);
+	writel(CLK_DIV_PERIC1_VAL, &clk->div_peric1);
+	writel(CLK_DIV_PERIC2_VAL, &clk->div_peric2);
+	writel(CLK_DIV_PERIC3_VAL, &clk->div_peric3);
+	writel(CLK_DIV_PERIC4_VAL, &clk->div_peric4);
+
+	writel(CLK_DIV_CPERI1_VAL, &clk->div_cperi1);
+
+	writel(CLK_DIV2_RATIO, &clk->clkdiv2_ratio);
+	writel(CLK_DIV4_RATIO, &clk->clkdiv4_ratio);
+	writel(CLK_DIV_G2D, &clk->div_g2d);
+
+	writel(CLK_SRC_TOP6_VAL, &clk->src_top6);
+	writel(CLK_SRC_CDREX_VAL, &clk->src_cdrex);
+	writel(CLK_SRC_KFC_VAL, &clk->src_kfc);
+}
+
+void system_clock_init(void)
+{
+	if (proid_is_exynos5420())
+		exynos5420_system_clock_init();
+	else
+		exynos5250_system_clock_init();
+}
+
 void clock_init_dp_clock(void)
 {
 	struct exynos5_clock *clk =
diff --git a/arch/arm/cpu/armv7/exynos/exynos5_setup.h b/arch/arm/cpu/armv7/exynos/exynos5_setup.h
index 696b386..8e05a00 100644
--- a/arch/arm/cpu/armv7/exynos/exynos5_setup.h
+++ b/arch/arm/cpu/armv7/exynos/exynos5_setup.h
@@ -12,42 +12,16 @@
 #include <config.h>
 #include <asm/arch/dmc.h>
 
-/* APLL_CON1	*/
-#define APLL_CON1_VAL	(0x00203800)
-
-/* MPLL_CON1	*/
-#define MPLL_CON1_VAL   (0x00203800)
-
-/* CPLL_CON1	*/
-#define CPLL_CON1_VAL	(0x00203800)
-
-/* GPLL_CON1	*/
-#define GPLL_CON1_VAL	(0x00203800)
-
-/* EPLL_CON1, CON2	*/
-#define EPLL_CON1_VAL	0x00000000
-#define EPLL_CON2_VAL	0x00000080
-
-/* VPLL_CON1, CON2	*/
-#define VPLL_CON1_VAL	0x00000000
-#define VPLL_CON2_VAL	0x00000080
+#define NOT_AVAILABLE		0
+#define DATA_MASK		0xFFFFF
 
-/* BPLL_CON1	*/
-#define BPLL_CON1_VAL	0x00203800
+#define ENABLE_BIT		0x1
+#define DISABLE_BIT		0x0
+#define CA_SWAP_EN		(1 << 0)
 
 /* Set PLL */
 #define set_pll(mdiv, pdiv, sdiv)	(1<<31 | mdiv<<16 | pdiv<<8 | sdiv)
 
-/* CLK_SRC_CPU	*/
-/* 0 = MOUTAPLL,  1 = SCLKMPLL	*/
-#define MUX_HPM_SEL             0
-#define MUX_CPU_SEL             0
-#define MUX_APLL_SEL            1
-
-#define CLK_SRC_CPU_VAL		((MUX_HPM_SEL << 20)    \
-				| (MUX_CPU_SEL << 16)  \
-				| (MUX_APLL_SEL))
-
 /* MEMCONTROL register bit fields */
 #define DMC_MEMCONTROL_CLK_STOP_DISABLE	(0 << 0)
 #define DMC_MEMCONTROL_DPWRDN_DISABLE	(0 << 1)
@@ -78,6 +52,7 @@
 
 /* MEMCONFIG0 register bit fields */
 #define DMC_MEMCONFIGX_CHIP_MAP_INTERLEAVED     (1 << 12)
+#define DMC_MEMCONFIG_CHIP_MAP_SPLIT		(2 << 12)
 #define DMC_MEMCONFIGX_CHIP_COL_10              (3 << 8)
 #define DMC_MEMCONFIGX_CHIP_ROW_14              (2 << 4)
 #define DMC_MEMCONFIGX_CHIP_ROW_15              (3 << 4)
@@ -90,6 +65,16 @@
 	DMC_MEMBASECONFIGX_CHIP_MASK(0x780)     \
 )
 
+/* As we use channel interleaving, therefore value of the base address
+ * register must be set as half of the bus base address
+ * RAM start addess is 0x2000_0000 which means chip_base is 0x20, so
+ * we need to set half 0x10 to the membaseconfigx registers
+ * see exynos5420 UM section 17.17.3.21 for more
+ */
+#define DMC_CHIP_BASE_0 0x10
+#define DMC_CHIP_BASE_1 0x50
+#define DMC_CHIP_MASK	0x7C0
+
 #define DMC_MEMBASECONFIG0_VAL  DMC_MEMBASECONFIG_VAL(0x40)
 #define DMC_MEMBASECONFIG1_VAL  DMC_MEMBASECONFIG_VAL(0x80)
 
@@ -113,29 +98,24 @@
 
 /* COJCONTROL register bit fields */
 #define DMC_CONCONTROL_IO_PD_CON_DISABLE	(0 << 3)
+#define DMC_CONCONTROL_IO_PD_CON_ENABLE		(1 << 3)
 #define DMC_CONCONTROL_AREF_EN_DISABLE		(0 << 5)
+#define DMC_CONCONTROL_AREF_EN_ENABLE		(1 << 5)
 #define DMC_CONCONTROL_EMPTY_DISABLE		(0 << 8)
 #define DMC_CONCONTROL_EMPTY_ENABLE		(1 << 8)
 #define DMC_CONCONTROL_RD_FETCH_DISABLE		(0x0 << 12)
 #define DMC_CONCONTROL_TIMEOUT_LEVEL0		(0xFFF << 16)
 #define DMC_CONCONTROL_DFI_INIT_START_DISABLE	(0 << 28)
 
-/* CLK_DIV_CPU0_VAL */
-#define CLK_DIV_CPU0_VAL	((ARM2_RATIO << 28)             \
-				| (APLL_RATIO << 24)            \
-				| (PCLK_DBG_RATIO << 20)        \
-				| (ATB_RATIO << 16)             \
-				| (PERIPH_RATIO << 12)          \
-				| (ACP_RATIO << 8)              \
-				| (CPUD_RATIO << 4)             \
-				| (ARM_RATIO))
+#define DMC_CONCONTROL_VAL	0x1FFF2101
 
+#define DREX_CONCONTROL_VAL	DMC_CONCONTROL_VAL			\
+				| DMC_CONCONTROL_AREF_EN_ENABLE		\
+				| DMC_CONCONTROL_IO_PD_CON_ENABLE
 
-/* CLK_FSYS */
-#define CLK_SRC_FSYS0_VAL              0x66666
-#define CLK_DIV_FSYS0_VAL	       0x0BB00000
+#define DMC_CONCONTROL_IO_PD_CON(x)		(x << 6)
 
-/* CLK_DIV_CPU1	*/
+/* CLK_DIV_CPU1 */
 #define HPM_RATIO               0x2
 #define COPY_RATIO              0x0
 
@@ -164,10 +144,370 @@
 /* CLK_DIV_SYSLFT */
 #define CLK_DIV_SYSLFT_VAL      0x00000311
 
+#define MUX_APLL_SEL_MASK	(1 << 0)
+#define MUX_MPLL_SEL_MASK	(1 << 8)
+#define MPLL_SEL_MOUT_MPLLFOUT	(2 << 8)
+#define MUX_CPLL_SEL_MASK	(1 << 8)
+#define MUX_EPLL_SEL_MASK	(1 << 12)
+#define MUX_VPLL_SEL_MASK	(1 << 16)
+#define MUX_GPLL_SEL_MASK	(1 << 28)
+#define MUX_BPLL_SEL_MASK	(1 << 0)
+#define MUX_HPM_SEL_MASK	(1 << 20)
+#define HPM_SEL_SCLK_MPLL	(1 << 21)
+#define PLL_LOCKED		(1 << 29)
+#define APLL_CON0_LOCKED	(1 << 29)
+#define MPLL_CON0_LOCKED	(1 << 29)
+#define BPLL_CON0_LOCKED	(1 << 29)
+#define CPLL_CON0_LOCKED	(1 << 29)
+#define EPLL_CON0_LOCKED	(1 << 29)
+#define GPLL_CON0_LOCKED	(1 << 29)
+#define VPLL_CON0_LOCKED	(1 << 29)
+#define CLK_REG_DISABLE		0x0
+#define TOP2_VAL		0x0110000
+
+/* SCLK_SRC_ISP - set SPI0/1 to 6 = SCLK_MPLL_USER */
+#define SPI0_ISP_SEL		6
+#define SPI1_ISP_SEL		6
+#define SCLK_SRC_ISP_VAL	(SPI1_ISP_SEL << 4) \
+				| (SPI0_ISP_SEL << 0)
+
+/* SCLK_DIV_ISP - set SPI0/1 to 0xf = divide by 16 */
+#define SPI0_ISP_RATIO		0xf
+#define SPI1_ISP_RATIO		0xf
+#define SCLK_DIV_ISP_VAL	(SPI1_ISP_RATIO << 12) \
+				| (SPI0_ISP_RATIO << 0)
+
+/* CLK_DIV_FSYS2 */
+#define MMC2_RATIO_MASK		0xf
+#define MMC2_RATIO_VAL		0x3
+#define MMC2_RATIO_OFFSET	0
+
+#define MMC2_PRE_RATIO_MASK	0xff
+#define MMC2_PRE_RATIO_VAL	0x9
+#define MMC2_PRE_RATIO_OFFSET	8
+
+#define MMC3_RATIO_MASK		0xf
+#define MMC3_RATIO_VAL		0x1
+#define MMC3_RATIO_OFFSET	16
+
+#define MMC3_PRE_RATIO_MASK	0xff
+#define MMC3_PRE_RATIO_VAL	0x0
+#define MMC3_PRE_RATIO_OFFSET	24
+
+/* CLK_SRC_LEX */
+#define CLK_SRC_LEX_VAL         0x0
+
+/* CLK_DIV_LEX */
+#define CLK_DIV_LEX_VAL         0x10
+
+/* CLK_DIV_R0X */
+#define CLK_DIV_R0X_VAL         0x10
+
+/* CLK_DIV_L0X */
+#define CLK_DIV_R1X_VAL         0x10
+
+/* CLK_DIV_ISP2 */
+#define CLK_DIV_ISP2_VAL        0x1
+
+/* CLK_SRC_KFC */
+#define SRC_KFC_HPM_SEL		(1 << 15)
+
+/* CLK_SRC_KFC */
+#define CLK_SRC_KFC_VAL		0x00008001
+
+/* CLK_DIV_KFC */
+#define CLK_DIV_KFC_VAL		0x03300110
+
+/* CLK_DIV2_RATIO */
+#define CLK_DIV2_RATIO		0x10111150
+
+/* CLK_DIV4_RATIO */
+#define CLK_DIV4_RATIO		0x00000003
+
+/* CLK_DIV_G2D */
+#define CLK_DIV_G2D		0x00000010
+
+/*
+ * DIV_DISP1_0
+ * For DP, divisor should be 2
+ */
+#define CLK_DIV_DISP1_0_FIMD1	(2 << 0)
+
+/* CLK_GATE_IP_DISP1 */
+#define CLK_GATE_DP1_ALLOW	(1 << 4)
+
+/* AUDIO CLK SEL */
+#define AUDIO0_SEL_EPLL		(0x6 << 28)
+#define AUDIO0_RATIO		0x5
+#define PCM0_RATIO		0x3
+#define DIV_MAU_VAL		(PCM0_RATIO << 24 | AUDIO0_RATIO << 20)
+
+
+/* CLK_SRC_CDREX */
+#define MUX_MCLK_CDR_MSPLL	(1 << 4)
+#define MUX_BPLL_SEL_FOUTBPLL   (1 << 0)
+#define BPLL_SEL_MASK   0x7
+#define FOUTBPLL        2
+
+#define DDR3PHY_CTRL_PHY_RESET	(1 << 0)
+#define DDR3PHY_CTRL_PHY_RESET_OFF	(0 << 0)
+
+#define PHY_CON0_RESET_VAL	0x17020a40
+#define P0_CMD_EN		(1 << 14)
+#define BYTE_RDLVL_EN		(1 << 13)
+#define CTRL_SHGATE		(1 << 8)
+
+#define PHY_CON1_RESET_VAL	0x09210100
+#define RDLVL_PASS_ADJ_VAL	0x6
+#define RDLVL_PASS_ADJ_OFFSET	16
+#define CTRL_GATEDURADJ_MASK	(0xf << 20)
+#define READ_LEVELLING_DDR3	0x0100
+
+#define PHY_CON2_RESET_VAL	0x00010004
+#define INIT_DESKEW_EN		(1 << 6)
+#define DLL_DESKEW_EN		(1 << 12)
+#define RDLVL_GATE_EN		(1 << 24)
+#define RDLVL_EN		(1 << 25)
+#define RDLVL_INCR_ADJ		(0x1 << 16)
+
+/* DREX_PAUSE */
+#define DREX_PAUSE_EN	(1 << 0)
+
+#define BYPASS_EN	(1 << 22)
+
+/********-----MEMMORY VAL----------***/
+#define PHY_CON0_VAL	0x17021A00
+
+#define PHY_CON12_RESET_VAL	0x10100070
+#define PHY_CON12_VAL		0x10107F50
+#define CTRL_START		(1 << 6)
+#define CTRL_DLL_ON		(1 << 5)
+#define CTRL_FORCE_MASK		(0x7F << 8)
+#define CTRL_LOCK_COARSE_MASK	(0x7F << 10)
+
+
+#define CTRL_OFFSETD_RESET_VAL	0x8
+#define CTRL_OFFSETD_VAL	0x7F
+
+#define CTRL_OFFSETR0		0x7F
+#define CTRL_OFFSETR1		0x7F
+#define CTRL_OFFSETR2		0x7F
+#define CTRL_OFFSETR3		0x7F
+#define PHY_CON4_VAL	(CTRL_OFFSETR0 << 0 | \
+				CTRL_OFFSETR1 << 8 | \
+				CTRL_OFFSETR2 << 16 | \
+				CTRL_OFFSETR3 << 24)
+#define PHY_CON4_RESET_VAL	0x08080808
+
+#define CTRL_OFFSETW0		0x7F
+#define CTRL_OFFSETW1		0x7F
+#define CTRL_OFFSETW2		0x7F
+#define CTRL_OFFSETW3		0x7F
+#define PHY_CON6_VAL	(CTRL_OFFSETW0 << 0 | \
+				CTRL_OFFSETW1 << 8 | \
+				CTRL_OFFSETW2 << 16 | \
+				CTRL_OFFSETW3 << 24)
+#define PHY_CON6_RESET_VAL	0x08080808
+
+#define PHY_CON14_RESET_VAL	0x001F0000
+#define CTRL_PULLD_DQS		0xF
+#define CTRL_PULLD_DQS_OFFSET	0
+
+/*ZQ Configurations */
+#define PHY_CON16_RESET_VAL	0x08000304
+
+#define ZQ_CLK_EN		(1 << 27)
+#define ZQ_CLK_DIV_EN		(1 << 18)
+#define ZQ_MANUAL_STR		(1 << 1)
+#define ZQ_DONE			(1 << 0)
+#define ZQ_MODE_DDS_OFFSET	24
+
+#define CTRL_RDLVL_GATE_ENABLE	1
+#define CTRL_RDLVL_GATE_DISABLE	0
+#define CTRL_RDLVL_DATA_ENABLE	2
+
+/* Direct Command */
+#define DIRECT_CMD_NOP			0x07000000
+#define DIRECT_CMD_PALL			0x01000000
+#define DIRECT_CMD_ZQINIT		0x0a000000
+#define DIRECT_CMD_CHANNEL_SHIFT	28
+#define DIRECT_CMD_CHIP_SHIFT		20
+#define DIRECT_CMD_BANK_SHIFT		16
+#define DIRECT_CMD_REFA		(5 << 24)
+#define DIRECT_CMD_MRS1		0x71C00
+#define DIRECT_CMD_MRS2		0x10BFC
+#define DIRECT_CMD_MRS3		0x0050C
+#define DIRECT_CMD_MRS4		0x00868
+#define DIRECT_CMD_MRS5		0x00C04
+
+/* Drive Strength */
+#define IMPEDANCE_48_OHM	4
+#define IMPEDANCE_40_OHM	5
+#define IMPEDANCE_34_OHM	6
+#define IMPEDANCE_30_OHM	7
+#define PHY_CON39_VAL_48_OHM	0x09240924
+#define PHY_CON39_VAL_40_OHM	0x0B6D0B6D
+#define PHY_CON39_VAL_34_OHM	0x0DB60DB6
+#define PHY_CON39_VAL_30_OHM	0x0FFF0FFF
+
+
+#define CTRL_BSTLEN_OFFSET	8
+#define CTRL_RDLAT_OFFSET	0
+
+#define CMD_DEFAULT_LPDDR3	0xF
+#define CMD_DEFUALT_OFFSET	0
+#define T_WRDATA_EN		0x7
+#define T_WRDATA_EN_DDR3	0x8
+#define T_WRDATA_EN_OFFSET	16
+#define T_WRDATA_EN_MASK	0x1f
+
+#define PHY_CON31_VAL	0x0C183060
+#define PHY_CON32_VAL	0x60C18306
+#define PHY_CON33_VAL	0x00000030
+
+#define PHY_CON31_RESET_VAL	0x0
+#define PHY_CON32_RESET_VAL	0x0
+#define PHY_CON33_RESET_VAL	0x0
+
+#define SL_DLL_DYN_CON_EN	(1 << 1)
+#define FP_RESYNC	(1 << 3)
+#define CTRL_START	(1 << 6)
+
+#define DMC_AREF_EN		(1 << 5)
+#define DMC_CONCONTROL_EMPTY	(1 << 8)
+#define DFI_INIT_START		(1 << 28)
+
+#define DMC_MEMCONTROL_VAL	0x00312700
+#define CLK_STOP_EN		(1 << 0)
+#define DPWRDN_EN		(1 << 1)
+#define DSREF_EN		(1 << 5)
+
+#define MEMBASECONFIG_CHIP_MASK_VAL	0x7E0
+#define MEMBASECONFIG_CHIP_MASK_OFFSET	0
+#define MEMBASECONFIG0_CHIP_BASE_VAL	0x20
+#define MEMBASECONFIG1_CHIP_BASE_VAL	0x40
+#define CHIP_BASE_OFFSET		16
+
+#define MEMCONFIG_VAL	0x1323
+#define PRECHCONFIG_DEFAULT_VAL	0xFF000000
+#define PWRDNCONFIG_DEFAULT_VAL	0xFFFF00FF
+
+#define TIMINGAREF_VAL	0x5d
+#define TIMINGROW_VAL	0x345A8692
+#define TIMINGDATA_VAL	0x3630065C
+#define TIMINGPOWER_VAL	0x50380336
+#define DFI_INIT_COMPLETE	(1 << 3)
+
+#define BRBRSVCONTROL_VAL	0x00000033
+#define BRBRSVCONFIG_VAL	0x88778877
+
+/* Clock Gating Control (CGCONTROL) register */
+#define MEMIF_CG_EN	(1 << 3) /* Memory interface clock gating */
+#define SCG_CG_EN	(1 << 2) /* Scheduler clock gating */
+#define BUSIF_WR_CG_EN	(1 << 1) /* Bus interface write channel clock gating */
+#define BUSIF_RD_CG_EN	(1 << 0) /* Bus interface read channel clock gating */
+#define DMC_INTERNAL_CG	(MEMIF_CG_EN | SCG_CG_EN | \
+				 BUSIF_WR_CG_EN | BUSIF_RD_CG_EN)
+
+/* DMC PHY Control0 register */
+#define PHY_CONTROL0_RESET_VAL	0x0
+#define MEM_TERM_EN	(1 << 31)	/* Termination enable for memory */
+#define PHY_TERM_EN	(1 << 30)	/* Termination enable for PHY */
+#define DMC_CTRL_SHGATE	(1 << 29)	/* Duration of DQS gating signal */
+#define FP_RSYNC	(1 << 3)	/* Force DLL resyncronization */
+
+/* Driver strength for CK, CKE, CS & CA */
+#define IMP_OUTPUT_DRV_40_OHM	0x5
+#define IMP_OUTPUT_DRV_30_OHM	0x7
+#define DA_3_DS_OFFSET		25
+#define DA_2_DS_OFFSET		22
+#define DA_1_DS_OFFSET		19
+#define DA_0_DS_OFFSET		16
+#define CA_CK_DRVR_DS_OFFSET	9
+#define CA_CKE_DRVR_DS_OFFSET	6
+#define CA_CS_DRVR_DS_OFFSET	3
+#define CA_ADR_DRVR_DS_OFFSET	0
+
+#define PHY_CON42_CTRL_BSTLEN_SHIFT	8
+#define PHY_CON42_CTRL_RDLAT_SHIFT	0
+
+/*
+ * Definitions that differ with SoC's.
+ * Below is the part defining macros for smdk5250.
+ * Else part introduces macros for smdk5420.
+ */
+#ifndef CONFIG_SMDK5420
+
+/* APLL_CON1 */
+#define APLL_CON1_VAL	(0x00203800)
+
+/* MPLL_CON1 */
+#define MPLL_CON1_VAL   (0x00203800)
+
+/* CPLL_CON1 */
+#define CPLL_CON1_VAL	(0x00203800)
+
+/* DPLL_CON1 */
+#define DPLL_CON1_VAL	(NOT_AVAILABLE)
+
+/* GPLL_CON1 */
+#define GPLL_CON1_VAL	(0x00203800)
+
+/* EPLL_CON1, CON2 */
+#define EPLL_CON1_VAL	0x00000000
+#define EPLL_CON2_VAL	0x00000080
+
+/* VPLL_CON1, CON2 */
+#define VPLL_CON1_VAL	0x00000000
+#define VPLL_CON2_VAL	0x00000080
+
+/* RPLL_CON1, CON2 */
+#define RPLL_CON1_VAL	NOT_AVAILABLE
+#define RPLL_CON2_VAL	NOT_AVAILABLE
+
+/* BPLL_CON1 */
+#define BPLL_CON1_VAL	0x00203800
+
+/* SPLL_CON1 */
+#define SPLL_CON1_VAL	NOT_AVAILABLE
+
+/* IPLL_CON1 */
+#define IPLL_CON1_VAL	NOT_AVAILABLE
+
+/* KPLL_CON1 */
+#define KPLL_CON1_VAL	NOT_AVAILABLE
+
+/* CLK_SRC_ISP */
+#define CLK_SRC_ISP_VAL		NOT_AVAILABLE
+#define CLK_DIV_ISP0_VAL	0x31
+#define CLK_DIV_ISP1_VAL	0x0
+
+/* CLK_FSYS */
+#define CLK_SRC_FSYS0_VAL              0x66666
+#define CLK_DIV_FSYS0_VAL	       0x0BB00000
+#define CLK_DIV_FSYS1_VAL	       NOT_AVAILABLE
+#define CLK_DIV_FSYS2_VAL	       NOT_AVAILABLE
+
+/* CLK_SRC_CPU */
+/* 0 = MOUTAPLL,  1 = SCLKMPLL */
+#define MUX_HPM_SEL             0
+#define MUX_CPU_SEL             0
+#define MUX_APLL_SEL            1
+
+#define CLK_SRC_CPU_VAL		((MUX_HPM_SEL << 20)    \
+				| (MUX_CPU_SEL << 16)  \
+				| (MUX_APLL_SEL))
+
 /* CLK_SRC_CDREX */
 #define CLK_SRC_CDREX_VAL       0x1
 
 /* CLK_DIV_CDREX */
+#define CLK_DIV_CDREX0_VAL	NOT_AVAILABLE
+#define CLK_DIV_CDREX1_VAL	NOT_AVAILABLE
+
+/* CLK_DIV_CPU0_VAL */
+#define CLK_DIV_CPU0_VAL	NOT_AVAILABLE
+
 #define MCLK_CDREX2_RATIO       0x0
 #define ACLK_EFCON_RATIO        0x1
 #define MCLK_DPHY_RATIO		0x1
@@ -247,6 +587,11 @@
 				| (MUX_ACLK_300_DISP1_SUB_SEL << 6)     \
 				| (MUX_ACLK_200_DISP1_SUB_SEL << 4))
 
+#define CLK_SRC_TOP4_VAL	NOT_AVAILABLE
+#define CLK_SRC_TOP5_VAL	NOT_AVAILABLE
+#define CLK_SRC_TOP6_VAL	NOT_AVAILABLE
+#define CLK_SRC_TOP7_VAL	NOT_AVAILABLE
+
 /* CLK_DIV_TOP0	*/
 #define ACLK_300_DISP1_RATIO	0x2
 #define ACLK_400_G3D_RATIO	0x0
@@ -279,40 +624,11 @@
 				| (ACLK_400_IOP_RATIO << 16)		\
 				| (ACLK_300_GSCL_RATIO << 12))
 
-/* APLL_LOCK	*/
-#define APLL_LOCK_VAL	(0x546)
-/* MPLL_LOCK	*/
-#define MPLL_LOCK_VAL	(0x546)
-/* CPLL_LOCK	*/
-#define CPLL_LOCK_VAL	(0x546)
-/* GPLL_LOCK	*/
-#define GPLL_LOCK_VAL	(0x546)
-/* EPLL_LOCK	*/
-#define EPLL_LOCK_VAL	(0x3A98)
-/* VPLL_LOCK	*/
-#define VPLL_LOCK_VAL	(0x3A98)
-/* BPLL_LOCK	*/
-#define BPLL_LOCK_VAL	(0x546)
+#define CLK_DIV_TOP2_VAL	NOT_AVAILABLE
 
-#define MUX_APLL_SEL_MASK	(1 << 0)
-#define MUX_MPLL_SEL_MASK	(1 << 8)
-#define MPLL_SEL_MOUT_MPLLFOUT	(2 << 8)
-#define MUX_CPLL_SEL_MASK	(1 << 8)
-#define MUX_EPLL_SEL_MASK	(1 << 12)
-#define MUX_VPLL_SEL_MASK	(1 << 16)
-#define MUX_GPLL_SEL_MASK	(1 << 28)
-#define MUX_BPLL_SEL_MASK	(1 << 0)
-#define MUX_HPM_SEL_MASK	(1 << 20)
-#define HPM_SEL_SCLK_MPLL	(1 << 21)
-#define APLL_CON0_LOCKED	(1 << 29)
-#define MPLL_CON0_LOCKED	(1 << 29)
-#define BPLL_CON0_LOCKED	(1 << 29)
-#define CPLL_CON0_LOCKED	(1 << 29)
-#define EPLL_CON0_LOCKED	(1 << 29)
-#define GPLL_CON0_LOCKED	(1 << 29)
-#define VPLL_CON0_LOCKED	(1 << 29)
-#define CLK_REG_DISABLE		0x0
-#define TOP2_VAL		0x0110000
+/* PLL Lock Value Factor */
+#define PLL_LOCK_FACTOR		250
+#define PLL_X_LOCK_FACTOR	3000
 
 /* CLK_SRC_PERIC0 */
 #define PWM_SEL		6
@@ -336,18 +652,6 @@
 				| (SPI1_SEL << 20) \
 				| (SPI0_SEL << 16))
 
-/* SCLK_SRC_ISP - set SPI0/1 to 6 = SCLK_MPLL_USER */
-#define SPI0_ISP_SEL		6
-#define SPI1_ISP_SEL		6
-#define SCLK_SRC_ISP_VAL	(SPI1_ISP_SEL << 4) \
-				| (SPI0_ISP_SEL << 0)
-
-/* SCLK_DIV_ISP - set SPI0/1 to 0xf = divide by 16 */
-#define SPI0_ISP_RATIO		0xf
-#define SPI1_ISP_RATIO		0xf
-#define SCLK_DIV_ISP_VAL	(SPI1_ISP_RATIO << 12) \
-				| (SPI0_ISP_RATIO << 0)
-
 /* CLK_DIV_PERIL0	*/
 #define UART5_RATIO	7
 #define UART4_RATIO	7
@@ -380,105 +684,200 @@
 #define PWM_RATIO		8
 #define CLK_DIV_PERIC3_VAL	(PWM_RATIO << 0)
 
-/* CLK_DIV_FSYS2 */
-#define MMC2_RATIO_MASK		0xf
-#define MMC2_RATIO_VAL		0x3
-#define MMC2_RATIO_OFFSET	0
 
-#define MMC2_PRE_RATIO_MASK	0xff
-#define MMC2_PRE_RATIO_VAL	0x9
-#define MMC2_PRE_RATIO_OFFSET	8
+/* CLK_DIV_PERIC4 */
+#define CLK_DIV_PERIC4_VAL	NOT_AVAILABLE
 
-#define MMC3_RATIO_MASK		0xf
-#define MMC3_RATIO_VAL		0x1
-#define MMC3_RATIO_OFFSET	16
+/* CLK_SRC_DISP1_0 */
+#define CLK_SRC_DISP1_0_VAL	0x6
+#define CLK_DIV_DISP1_0_VAL	NOT_AVAILABLE
 
-#define MMC3_PRE_RATIO_MASK	0xff
-#define MMC3_PRE_RATIO_VAL	0x0
-#define MMC3_PRE_RATIO_OFFSET	24
+#define APLL_FOUT		(1 << 0)
+#define KPLL_FOUT		NOT_AVAILABLE
 
-/* CLK_SRC_LEX */
-#define CLK_SRC_LEX_VAL         0x0
+#define CLK_DIV_CPERI1_VAL	NOT_AVAILABLE
 
-/* CLK_DIV_LEX */
-#define CLK_DIV_LEX_VAL         0x10
+#else
 
-/* CLK_DIV_R0X */
-#define CLK_DIV_R0X_VAL         0x10
+/* APLL_CON1 */
+#define APLL_CON1_VAL	(0x0020F300)
 
-/* CLK_DIV_L0X */
-#define CLK_DIV_R1X_VAL         0x10
+/* MPLL_CON1 */
+#define MPLL_CON1_VAL   (0x0020F300)
 
-/* CLK_DIV_ISP0 */
-#define CLK_DIV_ISP0_VAL        0x31
 
-/* CLK_DIV_ISP1 */
-#define CLK_DIV_ISP1_VAL        0x0
+/* CPLL_CON1 */
+#define CPLL_CON1_VAL	0x0020f300
 
-/* CLK_DIV_ISP2 */
-#define CLK_DIV_ISP2_VAL        0x1
+/* DPLL_CON1 */
+#define DPLL_CON1_VAL	(0x0020F300)
 
-/* CLK_SRC_DISP1_0 */
-#define CLK_SRC_DISP1_0_VAL	0x6
+/* GPLL_CON1 */
+#define GPLL_CON1_VAL	(NOT_AVAILABLE)
 
-/*
- * DIV_DISP1_0
- * For DP, divisor should be 2
- */
-#define CLK_DIV_DISP1_0_FIMD1	(2 << 0)
 
-/* CLK_GATE_IP_DISP1 */
-#define CLK_GATE_DP1_ALLOW	(1 << 4)
+/* EPLL_CON1, CON2 */
+#define EPLL_CON1_VAL	0x00000000
+#define EPLL_CON2_VAL	0x00000080
 
-#define DDR3PHY_CTRL_PHY_RESET	(1 << 0)
-#define DDR3PHY_CTRL_PHY_RESET_OFF	(0 << 0)
+/* VPLL_CON1, CON2 */
+#define VPLL_CON1_VAL	0x0020f300
+#define VPLL_CON2_VAL	NOT_AVAILABLE
 
-#define PHY_CON0_RESET_VAL	0x17020a40
-#define P0_CMD_EN		(1 << 14)
-#define BYTE_RDLVL_EN		(1 << 13)
-#define CTRL_SHGATE		(1 << 8)
+/* RPLL_CON1, CON2 */
+#define RPLL_CON1_VAL	0x00000000
+#define RPLL_CON2_VAL	0x00000080
 
-#define PHY_CON1_RESET_VAL	0x09210100
-#define CTRL_GATEDURADJ_MASK	(0xf << 20)
+/* BPLL_CON1 */
+#define BPLL_CON1_VAL	0x0020f300
 
-#define PHY_CON2_RESET_VAL	0x00010004
-#define INIT_DESKEW_EN		(1 << 6)
-#define RDLVL_GATE_EN		(1 << 24)
+/* SPLL_CON1 */
+#define SPLL_CON1_VAL	0x0020f300
 
-/*ZQ Configurations */
-#define PHY_CON16_RESET_VAL	0x08000304
+/* IPLL_CON1 */
+#define IPLL_CON1_VAL	0x00000080
 
-#define ZQ_CLK_DIV_EN		(1 << 18)
-#define ZQ_MANUAL_STR		(1 << 1)
-#define ZQ_DONE			(1 << 0)
+/* KPLL_CON1 */
+#define KPLL_CON1_VAL	0x200000
 
-#define CTRL_RDLVL_GATE_ENABLE	1
-#define CTRL_RDLVL_GATE_DISABLE	1
+/* CLK_SRC_ISP */
+#define CLK_SRC_ISP_VAL		0x33366000
+#define CLK_DIV_ISP0_VAL	0x13131300
+#define CLK_DIV_ISP1_VAL	0xbb110202
 
-/* Direct Command */
-#define DIRECT_CMD_NOP			0x07000000
-#define DIRECT_CMD_PALL			0x01000000
-#define DIRECT_CMD_ZQINIT		0x0a000000
-#define DIRECT_CMD_CHANNEL_SHIFT	28
-#define DIRECT_CMD_CHIP_SHIFT		20
 
-/* DMC PHY Control0 register */
-#define PHY_CONTROL0_RESET_VAL	0x0
-#define MEM_TERM_EN	(1 << 31)	/* Termination enable for memory */
-#define PHY_TERM_EN	(1 << 30)	/* Termination enable for PHY */
-#define DMC_CTRL_SHGATE	(1 << 29)	/* Duration of DQS gating signal */
-#define FP_RSYNC	(1 << 3)	/* Force DLL resyncronization */
+/* CLK_FSYS */
+#define CLK_SRC_FSYS0_VAL              0x33033300
+#define CLK_DIV_FSYS0_VAL	       0x0
+#define CLK_DIV_FSYS1_VAL	       0x04f13c4f
+#define CLK_DIV_FSYS2_VAL	       0x041d0000
+
+/* CLK_SRC_CPU */
+/* 0 = MOUTAPLL,  1 = SCLKMPLL */
+#define MUX_HPM_SEL             1
+#define MUX_CPU_SEL             0
+#define MUX_APLL_SEL            1
 
-/* Driver strength for CK, CKE, CS & CA */
-#define IMP_OUTPUT_DRV_40_OHM	0x5
-#define IMP_OUTPUT_DRV_30_OHM	0x7
-#define CA_CK_DRVR_DS_OFFSET	9
-#define CA_CKE_DRVR_DS_OFFSET	6
-#define CA_CS_DRVR_DS_OFFSET	3
-#define CA_ADR_DRVR_DS_OFFSET	0
+#define CLK_SRC_CPU_VAL		((MUX_HPM_SEL << 20)    \
+				| (MUX_CPU_SEL << 16)  \
+				| (MUX_APLL_SEL))
 
-#define PHY_CON42_CTRL_BSTLEN_SHIFT	8
-#define PHY_CON42_CTRL_RDLAT_SHIFT	0
+/* CLK_SRC_CDREX */
+#define CLK_SRC_CDREX_VAL       0x00000011
+
+/* CLK_DIV_CDREX */
+#define CLK_DIV_CDREX0_VAL	0x30010100
+#define CLK_DIV_CDREX1_VAL	0x300
+
+#define CLK_DIV_CDREX_VAL       0x17010100
+
+/* CLK_DIV_CPU0_VAL */
+#define CLK_DIV_CPU0_VAL	0x01440020
+
+/* CLK_SRC_TOP */
+#define CLK_SRC_TOP0_VAL	0x12221222
+#define CLK_SRC_TOP1_VAL	0x00100200
+#define CLK_SRC_TOP2_VAL	0x11101000
+#define CLK_SRC_TOP3_VAL	0x11111111
+#define CLK_SRC_TOP4_VAL	0x11110111
+#define CLK_SRC_TOP5_VAL	0x11111100
+#define CLK_SRC_TOP6_VAL	0x11110111
+#define CLK_SRC_TOP7_VAL	0x00022200
+
+/* CLK_DIV_TOP */
+#define CLK_DIV_TOP0_VAL	0x23712311
+#define CLK_DIV_TOP1_VAL	0x13100B00
+#define CLK_DIV_TOP2_VAL	0x11101100
+
+/* PLL Lock Value Factor */
+#define PLL_LOCK_FACTOR		200
+#define PLL_X_LOCK_FACTOR	3000
+
+/* CLK_SRC_PERIC0 */
+#define SPDIF_SEL	1
+#define PWM_SEL		3
+#define UART4_SEL	3
+#define UART3_SEL	3
+#define UART2_SEL	3
+#define UART1_SEL	3
+#define UART0_SEL	3
+/* SRC_CLOCK = SCLK_RPLL */
+#define CLK_SRC_PERIC0_VAL	((SPDIF_SEL << 28)	\
+				| (PWM_SEL << 24)	\
+				| (UART4_SEL << 20)	\
+				| (UART3_SEL << 16)	\
+				| (UART2_SEL << 12)	\
+				| (UART1_SEL << 8)	\
+				| (UART0_SEL << 4))
+
+/* CLK_SRC_PERIC1 */
+/* SRC_CLOCK = SCLK_EPLL */
+#define SPI0_SEL		6
+#define SPI1_SEL		6
+#define SPI2_SEL		6
+#define AUDIO0_SEL		6
+#define AUDIO1_SEL		6
+#define AUDIO2_SEL		6
+#define CLK_SRC_PERIC1_VAL	((SPI2_SEL << 28)	\
+				| (SPI1_SEL << 24)	\
+				| (SPI0_SEL << 20)	\
+				| (AUDIO2_SEL << 16)	\
+				| (AUDIO2_SEL << 12)	\
+				| (AUDIO2_SEL << 8))
+
+/* CLK_DIV_PERIC0 */
+#define PWM_RATIO	8
+#define UART4_RATIO	9
+#define UART3_RATIO	9
+#define UART2_RATIO	9
+#define UART1_RATIO	9
+#define UART0_RATIO	9
+
+#define CLK_DIV_PERIC0_VAL	((PWM_RATIO << 28)	\
+				| (UART4_RATIO << 24)	\
+				| (UART3_RATIO << 20)    \
+				| (UART2_RATIO << 16)    \
+				| (UART1_RATIO << 12)    \
+				| (UART0_RATIO << 8))
+/* CLK_DIV_PERIC1 */
+#define SPI2_RATIO		0x1
+#define SPI1_RATIO		0x1
+#define SPI0_RATIO		0x1
+#define CLK_DIV_PERIC1_VAL	((SPI2_RATIO << 28)	\
+				| (SPI1_RATIO << 24)	\
+				| (SPI0_RATIO << 20))
+
+/* CLK_DIV_PERIC2 */
+#define PCM2_RATIO		0x3
+#define PCM1_RATIO		0x3
+#define CLK_DIV_PERIC2_VAL	((PCM2_RATIO << 24) \
+				| (PCM1_RATIO << 16))
+
+/* CLK_DIV_PERIC3 */
+#define AUDIO2_RATIO		0x5
+#define AUDIO1_RATIO		0x5
+#define AUDIO0_RATIO		0x5
+#define CLK_DIV_PERIC3_VAL	((AUDIO2_RATIO << 28)	\
+				| (AUDIO1_RATIO << 24)	\
+				| (AUDIO0_RATIO << 20))
+
+/* CLK_DIV_PERIC4 */
+#define SPI2_PRE_RATIO		0x2
+#define SPI1_PRE_RATIO		0x2
+#define SPI0_PRE_RATIO		0x2
+#define CLK_DIV_PERIC4_VAL	((SPI2_PRE_RATIO << 24)	\
+				| (SPI1_PRE_RATIO << 16) \
+				| (SPI0_PRE_RATIO << 8))
+
+/* CLK_SRC_DISP1_0 */
+#define CLK_SRC_DISP1_0_VAL	0x10666600
+#define CLK_DIV_DISP1_0_VAL	0x01050211
+
+#define APLL_FOUT		(1 << 0)
+#define KPLL_FOUT		(1 << 0)
+
+#define CLK_DIV_CPERI1_VAL	0x3f3f0000
+#endif
 
 struct mem_timings;
 
@@ -490,7 +889,7 @@ enum {
 };
 
 /*
- * Memory variant specific initialization code
+ * Memory variant specific initialization code for DDR3
  *
  * @param mem		Memory timings for this memory type.
  * @param mem_iv_size	Memory interleaving size is a configurable parameter
@@ -503,6 +902,9 @@ enum {
 int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size,
 			int reset);
 
+/* Memory variant specific initialization code for LPDDR3 */
+void lpddr3_mem_ctrl_init(void);
+
 /*
  * Configure ZQ I/O interface
  *
@@ -532,14 +934,6 @@ void dmc_config_mrs(struct mem_timings *mem, struct exynos5_dmc *dmc);
 void dmc_config_prech(struct mem_timings *mem, struct exynos5_dmc *dmc);
 
 /*
- * Configure the memconfig and membaseconfig registers
- *
- * @param mem		Memory timings for this memory type.
- * @param exynos5_dmc	Pointer to struct of DMC registers
- */
-void dmc_config_memory(struct mem_timings *mem, struct exynos5_dmc *dmc);
-
-/*
  * Reset the DLL. This function is common between DDR3 and LPDDR2.
  * However, the reset value is different. So we are passing a flag
  * ddr_mode to distinguish between LPDDR2 and DDR3.
diff --git a/arch/arm/include/asm/arch-exynos/clk.h b/arch/arm/include/asm/arch-exynos/clk.h
index 71075bd..abce246 100644
--- a/arch/arm/include/asm/arch-exynos/clk.h
+++ b/arch/arm/include/asm/arch-exynos/clk.h
@@ -14,6 +14,7 @@
 #define HPLL	3
 #define VPLL	4
 #define BPLL	5
+#define RPLL	6
 
 enum pll_src_bit {
 	EXYNOS_SRC_MPLL = 6,
diff --git a/arch/arm/include/asm/arch-exynos/clock.h b/arch/arm/include/asm/arch-exynos/clock.h
index 2b97b9a..c3dce1c 100644
--- a/arch/arm/include/asm/arch-exynos/clock.h
+++ b/arch/arm/include/asm/arch-exynos/clock.h
@@ -858,6 +858,500 @@ struct exynos5_clock {
 	unsigned char	res123[0xf5d8];
 };
 
+struct exynos5420_clock {
+	unsigned int	apll_lock;			/* 0x10010000 */
+	unsigned char	res1[0xfc];
+	unsigned int	apll_con0;
+	unsigned int	apll_con1;
+	unsigned char	res2[0xf8];
+	unsigned int	src_cpu;
+	unsigned char	res3[0x1fc];
+	unsigned int	mux_stat_cpu;
+	unsigned char	res4[0xfc];
+	unsigned int	div_cpu0;		/* 0x10010500 */
+	unsigned int	div_cpu1;
+	unsigned char	res5[0xf8];
+	unsigned int	div_stat_cpu0;
+	unsigned int	div_stat_cpu1;
+	unsigned char	res6[0xf8];
+	unsigned int	gate_bus_cpu;
+	unsigned char	res7[0xfc];
+	unsigned int	gate_sclk_cpu;
+	unsigned char	res8[0x1fc];
+	unsigned int	clkout_cmu_cpu;		/* 0x10010a00 */
+	unsigned int	clkout_cmu_cpu_div_stat;
+	unsigned char	res9[0x5f8];
+	unsigned int	armclk_stopctrl;
+	unsigned char	res10[0x4];
+	unsigned int	arm_ema_ctrl;
+	unsigned int	arm_ema_status;
+	unsigned char	res11[0x10];
+	unsigned int	pwr_ctrl;
+	unsigned int	pwr_ctrl2;
+	unsigned char	res12[0xd8];
+	unsigned int	apll_con0_l8;		/* 0x1001100 */
+	unsigned int	apll_con0_l7;
+	unsigned int	apll_con0_l6;
+	unsigned int	apll_con0_l5;
+	unsigned int	apll_con0_l4;
+	unsigned int	apll_con0_l3;
+	unsigned int	apll_con0_l2;
+	unsigned int	apll_con0_l1;
+	unsigned int	iem_control;
+	unsigned char	res13[0xdc];
+	unsigned int	apll_con1_l8;		/* 0x10011200 */
+	unsigned int	apll_con1_l7;
+	unsigned int	apll_con1_l6;
+	unsigned int	apll_con1_l5;
+	unsigned int	apll_con1_l4;
+	unsigned int	apll_con1_l3;
+	unsigned int	apll_con1_l2;
+	unsigned int	apll_con1_l1;
+	unsigned char	res14[0xe0];
+	unsigned int	clkdiv_iem_l8;
+	unsigned int	clkdiv_iem_l7;		/* 0x10011304 */
+	unsigned int	clkdiv_iem_l6;
+	unsigned int	clkdiv_iem_l5;
+	unsigned int	clkdiv_iem_l4;
+	unsigned int	clkdiv_iem_l3;
+	unsigned int	clkdiv_iem_l2;
+	unsigned int	clkdiv_iem_l1;
+	unsigned char	res15[0xe0];
+	unsigned int	l2_status;
+	unsigned char	res16[0x0c];
+	unsigned int	cpu_status;		/* 0x10011410 */
+	unsigned char	res17[0x0c];
+	unsigned int	ptm_status;
+	unsigned char	res18[0xbdc];
+	unsigned int	cmu_cpu_spare0;
+	unsigned int	cmu_cpu_spare1;
+	unsigned int	cmu_cpu_spare2;
+	unsigned int	cmu_cpu_spare3;
+	unsigned int	cmu_cpu_spare4;
+	unsigned char	res19[0x1fdc];
+	unsigned int	cmu_cpu_version;
+	unsigned char	res20[0x20c];
+	unsigned int	src_cperi0;		/* 0x10014200 */
+	unsigned int	src_cperi1;
+	unsigned char	res21[0xf8];
+	unsigned int	src_mask_cperi;
+	unsigned char	res22[0x100];
+	unsigned int	mux_stat_cperi1;
+	unsigned char	res23[0xfc];
+	unsigned int	div_cperi1;
+	unsigned char	res24[0xfc];
+	unsigned int	div_stat_cperi1;
+	unsigned char	res25[0xf8];
+	unsigned int	gate_bus_cperi0;	/* 0x10014700 */
+	unsigned int	gate_bus_cperi1;
+	unsigned char	res26[0xf8];
+	unsigned int	gate_sclk_cperi;
+	unsigned char	res27[0xfc];
+	unsigned int	gate_ip_cperi;
+	unsigned char	res28[0xfc];
+	unsigned int	clkout_cmu_cperi;
+	unsigned int	clkout_cmu_cperi_div_stat;
+	unsigned char	res29[0x5f8];
+	unsigned int	dcgidx_map0;		/* 0x10015000 */
+	unsigned int	dcgidx_map1;
+	unsigned int	dcgidx_map2;
+	unsigned char	res30[0x14];
+	unsigned int	dcgperf_map0;
+	unsigned int	dcgperf_map1;
+	unsigned char	res31[0x18];
+	unsigned int	dvcidx_map;
+	unsigned char	res32[0x1c];
+	unsigned int	freq_cpu;
+	unsigned int	freq_dpm;
+	unsigned char	res33[0x18];
+	unsigned int	dvsemclk_en;		/* 0x10015080 */
+	unsigned int	maxperf;
+	unsigned char	res34[0x2e78];
+	unsigned int	cmu_cperi_spare0;
+	unsigned int	cmu_cperi_spare1;
+	unsigned int	cmu_cperi_spare2;
+	unsigned int	cmu_cperi_spare3;
+	unsigned int	cmu_cperi_spare4;
+	unsigned int	cmu_cperi_spare5;
+	unsigned int	cmu_cperi_spare6;
+	unsigned int	cmu_cperi_spare7;
+	unsigned int	cmu_cperi_spare8;
+	unsigned char	res35[0xcc];
+	unsigned int	cmu_cperi_version;		/* 0x10017ff0 */
+	unsigned char	res36[0x50c];
+	unsigned int	div_g2d;
+	unsigned char	res37[0xfc];
+	unsigned int	div_stat_g2d;
+	unsigned char	res38[0xfc];
+	unsigned int	gate_bus_g2d;
+	unsigned char	res39[0xfc];
+	unsigned int	gate_ip_g2d;
+	unsigned char	res40[0x1fc];
+	unsigned int	clkout_cmu_g2d;
+	unsigned int	clkout_cmu_g2d_div_stat;	/* 0x10018a04 */
+	unsigned char	res41[0xf8];
+	unsigned int	cmu_g2d_spare0;
+	unsigned int	cmu_g2d_spare1;
+	unsigned int	cmu_g2d_spare2;
+	unsigned int	cmu_g2d_spare3;
+	unsigned int	cmu_g2d_spare4;
+	unsigned char	res42[0x34dc];
+	unsigned int	cmu_g2d_version;
+	unsigned char	res43[0x30c];
+	unsigned int	div_cmu_isp0;
+	unsigned int	div_cmu_isp1;
+	unsigned int	div_isp2;		/* 0x1001c308 */
+	unsigned char	res44[0xf4];
+	unsigned int	div_stat_cmu_isp0;
+	unsigned int	div_stat_cmu_isp1;
+	unsigned int	div_stat_isp2;
+	unsigned char	res45[0x2f4];
+	unsigned int	gate_bus_isp0;
+	unsigned int	gate_bus_isp1;
+	unsigned int	gate_bus_isp2;
+	unsigned int	gate_bus_isp3;
+	unsigned char	res46[0xf0];
+	unsigned int	gate_ip_isp0;
+	unsigned int	gate_ip_isp1;
+	unsigned char	res47[0xf8];
+	unsigned int	gate_sclk_isp;
+	unsigned char	res48[0x0c];
+	unsigned int	mcuisp_pwr_ctrl;		/* 0x1001c910 */
+	unsigned char	res49[0x0ec];
+	unsigned int	clkout_cmu_isp;
+	unsigned int	clkout_cmu_isp_div_stat;
+	unsigned char	res50[0xf8];
+	unsigned int	cmu_isp_spare0;
+	unsigned int	cmu_isp_spare1;
+	unsigned int	cmu_isp_spare2;
+	unsigned int	cmu_isp_spare3;
+	unsigned char	res51[0x34e0];
+	unsigned int	cmu_isp_version;
+	unsigned char	res52[0x2c];
+	unsigned int	cpll_lock;			/* 10020020 */
+	unsigned char	res53[0xc];
+	unsigned int	dpll_lock;
+	unsigned char	res54[0xc];
+	unsigned int	epll_lock;
+	unsigned char	res55[0xc];
+	unsigned int	rpll_lock;
+	unsigned char	res56[0xc];
+	unsigned int	ipll_lock;
+	unsigned char	res57[0xc];
+	unsigned int	spll_lock;
+	unsigned char	res58[0xc];
+	unsigned int	vpll_lock;
+	unsigned char	res59[0xc];
+	unsigned int	mpll_lock;
+	unsigned char	res60[0x8c];
+	unsigned int	cpll_con0;			/* 10020120 */
+	unsigned int	cpll_con1;
+	unsigned int	dpll_con0;
+	unsigned int	dpll_con1;
+	unsigned int	epll_con0;
+	unsigned int	epll_con1;
+	unsigned int	epll_con2;
+	unsigned char	res601[0x4];
+	unsigned int	rpll_con0;
+	unsigned int	rpll_con1;
+	unsigned int	rpll_con2;
+	unsigned char	res602[0x4];
+	unsigned int	ipll_con0;
+	unsigned int	ipll_con1;
+	unsigned char	res61[0x8];
+	unsigned int	spll_con0;
+	unsigned int	spll_con1;
+	unsigned char	res62[0x8];
+	unsigned int	vpll_con0;
+	unsigned int	vpll_con1;
+	unsigned char	res63[0x8];
+	unsigned int	mpll_con0;
+	unsigned int	mpll_con1;
+	unsigned char	res64[0x78];
+	unsigned int	src_top0;		/* 0x10020200 */
+	unsigned int	src_top1;
+	unsigned int	src_top2;
+	unsigned int	src_top3;
+	unsigned int	src_top4;
+	unsigned int	src_top5;
+	unsigned int	src_top6;
+	unsigned int	src_top7;
+	unsigned char	res65[0xc];
+	unsigned int	src_disp10;		/* 0x1002022c */
+	unsigned char	res66[0x10];
+	unsigned int	src_mau;
+	unsigned int	src_fsys;
+	unsigned char	res67[0x8];
+	unsigned int	src_peric0;
+	unsigned int	src_peric1;
+	unsigned char	res68[0x18];
+	unsigned int	src_isp;
+	unsigned char	res69[0x0c];
+	unsigned int	src_top10;
+	unsigned int	src_top11;
+	unsigned int	src_top12;
+	unsigned char	res70[0x74];
+	unsigned int	src_mask_top0;
+	unsigned int	src_mask_top1;
+	unsigned int	src_mask_top2;
+	unsigned char	res71[0x10];
+	unsigned int	src_mask_top7;
+	unsigned char	res72[0xc];
+	unsigned int	src_mask_disp10;	/* 0x1002032c */
+	unsigned char	res73[0x4];
+	unsigned int	src_mask_mau;
+	unsigned char	res74[0x8];
+	unsigned int	src_mask_fsys;
+	unsigned char	res75[0xc];
+	unsigned int	src_mask_peric0;
+	unsigned int	src_mask_peric1;
+	unsigned char	res76[0x18];
+	unsigned int	src_mask_isp;
+	unsigned char	res77[0x8c];
+	unsigned int	mux_stat_top0;		/* 0x10020400 */
+	unsigned int	mux_stat_top1;
+	unsigned int	mux_stat_top2;
+	unsigned int	mux_stat_top3;
+	unsigned int	mux_stat_top4;
+	unsigned int	mux_stat_top5;
+	unsigned int	mux_stat_top6;
+	unsigned int	mux_stat_top7;
+	unsigned char	res78[0x60];
+	unsigned int	mux_stat_top10;
+	unsigned int	mux_stat_top11;
+	unsigned int	mux_stat_top12;
+	unsigned char	res79[0x74];
+	unsigned int	div_top0;		/* 0x10020500 */
+	unsigned int	div_top1;
+	unsigned int	div_top2;
+	unsigned char	res80[0x20];
+	unsigned int	div_disp10;
+	unsigned char	res81[0x14];
+	unsigned int	div_mau;
+	unsigned int	div_fsys0;
+	unsigned int	div_fsys1;
+	unsigned int	div_fsys2;
+	unsigned char	res82[0x4];
+	unsigned int	div_peric0;
+	unsigned int	div_peric1;
+	unsigned int	div_peric2;
+	unsigned int	div_peric3;
+	unsigned int	div_peric4;		/* 0x10020568 */
+	unsigned char	res83[0x14];
+	unsigned int	div_isp0;
+	unsigned int	div_isp1;
+	unsigned char	res84[0x8];
+	unsigned int	clkdiv2_ratio;
+	unsigned char	res850[0xc];
+	unsigned int	clkdiv4_ratio;
+	unsigned char	res85[0x5c];
+	unsigned int	div_stat_top0;
+	unsigned int	div_stat_top1;
+	unsigned int	div_stat_top2;
+	unsigned char	res86[0x20];
+	unsigned int	div_stat_disp10;
+	unsigned char	res87[0x14];
+	unsigned int	div_stat_mau;		/* 0x10020644 */
+	unsigned int	div_stat_fsys0;
+	unsigned int	div_stat_fsys1;
+	unsigned int	div_stat_fsys2;
+	unsigned char	res88[0x4];
+	unsigned int	div_stat_peric0;
+	unsigned int	div_stat_peric1;
+	unsigned int	div_stat_peric2;
+	unsigned int	div_stat_peric3;
+	unsigned int	div_stat_peric4;
+	unsigned char	res89[0x14];
+	unsigned int	div_stat_isp0;
+	unsigned int	div_stat_isp1;
+	unsigned char	res90[0x8];
+	unsigned int	clkdiv2_stat0;
+	unsigned char	res91[0xc];
+	unsigned int	clkdiv4_stat;
+	unsigned char	res92[0x5c];
+	unsigned int	gate_bus_top;		/* 0x10020700 */
+	unsigned char	res93[0xc];
+	unsigned int	gate_bus_gscl0;
+	unsigned char	res94[0xc];
+	unsigned int	gate_bus_gscl1;
+	unsigned char	res95[0x4];
+	unsigned int	gate_bus_disp1;
+	unsigned char	res96[0x4];
+	unsigned int	gate_bus_wcore;
+	unsigned int	gate_bus_mfc;
+	unsigned int	gate_bus_g3d;
+	unsigned int	gate_bus_gen;
+	unsigned int	gate_bus_fsys0;
+	unsigned int	gate_bus_fsys1;
+	unsigned int	gate_bus_fsys2;
+	unsigned int	gate_bus_mscl;
+	unsigned int	gate_bus_peric;
+	unsigned int	gate_bus_peric1;
+	unsigned char	res97[0x8];
+	unsigned int	gate_bus_peris0;
+	unsigned int	gate_bus_peris1;	/* 0x10020764 */
+	unsigned char	res98[0x8];
+	unsigned int	gate_bus_noc;
+	unsigned char	res99[0xac];
+	unsigned int	gate_top_sclk_gscl;
+	unsigned char	res1000[0x4];
+	unsigned int	gate_top_sclk_disp1;
+	unsigned char	res100[0x10];
+	unsigned int	gate_top_sclk_mau;
+	unsigned int	gate_top_sclk_fsys;
+	unsigned char	res101[0xc];
+	unsigned int	gate_top_sclk_peric;
+	unsigned char	res102[0xc];
+	unsigned int	gate_top_sclk_cperi;
+	unsigned char	res103[0xc];
+	unsigned int	gate_top_sclk_isp;
+	unsigned char	res104[0x9c];
+	unsigned int	gate_ip_gscl0;
+	unsigned char	res105[0xc];
+	unsigned int	gate_ip_gscl1;
+	unsigned char	res106[0x4];
+	unsigned int	gate_ip_disp1;
+	unsigned int	gate_ip_mfc;
+	unsigned int	gate_ip_g3d;
+	unsigned int	gate_ip_gen;		/* 0x10020934 */
+	unsigned char	res107[0xc];
+	unsigned int	gate_ip_fsys;
+	unsigned char	res108[0x8];
+	unsigned int	gate_ip_peric;
+	unsigned char	res109[0xc];
+	unsigned int	gate_ip_peris;
+	unsigned char	res110[0xc];
+	unsigned int	gate_ip_mscl;
+	unsigned char	res111[0xc];
+	unsigned int	gate_ip_block;
+	unsigned char	res112[0xc];
+	unsigned int	bypass;
+	unsigned char	res113[0x6c];
+	unsigned int	clkout_cmu_top;
+	unsigned int	clkout_cmu_top_div_stat;
+	unsigned char	res114[0xf8];
+	unsigned int	clkout_top_spare0;
+	unsigned int	clkout_top_spare1;
+	unsigned int	clkout_top_spare2;
+	unsigned int	clkout_top_spare3;
+	unsigned char	res115[0x34e0];
+	unsigned int	clkout_top_version;
+	unsigned char	res116[0xc01c];
+	unsigned int	bpll_lock;			/* 0x10030010 */
+	unsigned char	res117[0xfc];
+	unsigned int	bpll_con0;
+	unsigned int	bpll_con1;
+	unsigned char	res118[0xe8];
+	unsigned int	src_cdrex;
+	unsigned char	res119[0x1fc];
+	unsigned int	mux_stat_cdrex;
+	unsigned char	res120[0xfc];
+	unsigned int	div_cdrex0;
+	unsigned int	div_cdrex1;
+	unsigned char	res121[0xf8];
+	unsigned int	div_stat_cdrex;
+	unsigned char	res1211[0xfc];
+	unsigned int	gate_bus_cdrex;
+	unsigned int	gate_bus_cdrex1;
+	unsigned char	res122[0x1f8];
+	unsigned int	gate_ip_cdrex;
+	unsigned char	res123[0x10];
+	unsigned int	dmc_freq_ctrl;		/* 0x10030914 */
+	unsigned char	res124[0x4];
+	unsigned int	pause;
+	unsigned int	ddrphy_lock_ctrl;
+	unsigned char	res125[0xdc];
+	unsigned int	clkout_cmu_cdrex;
+	unsigned int	clkout_cmu_cdrex_div_stat;
+	unsigned char	res126[0x8];
+	unsigned int	lpddr3phy_ctrl;
+	unsigned int	lpddr3phy_con0;
+	unsigned int	lpddr3phy_con1;
+	unsigned int	lpddr3phy_con2;
+	unsigned int	lpddr3phy_con3;
+	unsigned int	lpddr3phy_con4;
+	unsigned int	lpddr3phy_con5;		/* 0x10030a28 */
+	unsigned int	pll_div2_sel;
+	unsigned char	res127[0xd0];
+	unsigned int	cmu_cdrex_spare0;
+	unsigned int	cmu_cdrex_spare1;
+	unsigned int	cmu_cdrex_spare2;
+	unsigned int	cmu_cdrex_spare3;
+	unsigned int	cmu_cdrex_spare4;
+	unsigned char	res128[0x34dc];
+	unsigned int	cmu_cdrex_version;		/* 0x10033ff0 */
+	unsigned char	res129[0x400c];
+	unsigned int	kpll_lock;
+	unsigned char	res130[0xfc];
+	unsigned int	kpll_con0;
+	unsigned int	kpll_con1;
+	unsigned char	res131[0xf8];
+	unsigned int	src_kfc;
+	unsigned char	res132[0x1fc];
+	unsigned int	mux_stat_kfc;		/* 0x10038400 */
+	unsigned char	res133[0xfc];
+	unsigned int	div_kfc0;
+	unsigned char	res134[0xfc];
+	unsigned int	div_stat_kfc0;
+	unsigned char	res135[0xfc];
+	unsigned int	gate_bus_cpu_kfc;
+	unsigned char	res136[0xfc];
+	unsigned int	gate_sclk_cpu_kfc;
+	unsigned char	res137[0x1fc];
+	unsigned int	clkout_cmu_kfc;
+	unsigned int	clkout_cmu_kfc_div_stat;	/* 0x10038a04 */
+	unsigned char	res138[0x5f8];
+	unsigned int	armclk_stopctrl_kfc;
+	unsigned char	res139[0x4];
+	unsigned int	armclk_ema_ctrl_kfc;
+	unsigned int	armclk_ema_status_kfc;
+	unsigned char	res140[0x10];
+	unsigned int	pwr_ctrl_kfc;
+	unsigned int	pwr_ctrl2_kfc;
+	unsigned char	res141[0xd8];
+	unsigned int	kpll_con0_l8;
+	unsigned int	kpll_con0_l7;
+	unsigned int	kpll_con0_l6;
+	unsigned int	kpll_con0_l5;
+	unsigned int	kpll_con0_l4;
+	unsigned int	kpll_con0_l3;
+	unsigned int	kpll_con0_l2;
+	unsigned int	kpll_con0_l1;
+	unsigned int	iem_control_kfc;		/* 0x10039120 */
+	unsigned char	res142[0xdc];
+	unsigned int	kpll_con1_l8;
+	unsigned int	kpll_con1_l7;
+	unsigned int	kpll_con1_l6;
+	unsigned int	kpll_con1_l5;
+	unsigned int	kpll_con1_l4;
+	unsigned int	kpll_con1_l3;
+	unsigned int	kpll_con1_l2;
+	unsigned int	kpll_con1_l1;
+	unsigned char	res143[0xe0];
+	unsigned int	clkdiv_iem_l8_kfc;		/* 0x10039300 */
+	unsigned int	clkdiv_iem_l7_kfc;
+	unsigned int	clkdiv_iem_l6_kfc;
+	unsigned int	clkdiv_iem_l5_kfc;
+	unsigned int	clkdiv_iem_l4_kfc;
+	unsigned int	clkdiv_iem_l3_kfc;
+	unsigned int	clkdiv_iem_l2_kfc;
+	unsigned int	clkdiv_iem_l1_kfc;
+	unsigned char	res144[0xe0];
+	unsigned int	l2_status_kfc;
+	unsigned char	res145[0xc];
+	unsigned int	cpu_status_kfc;		/* 0x10039410 */
+	unsigned char	res146[0xc];
+	unsigned int	ptm_status_kfc;
+	unsigned char	res147[0xbdc];
+	unsigned int	cmu_kfc_spare0;
+	unsigned int	cmu_kfc_spare1;
+	unsigned int	cmu_kfc_spare2;
+	unsigned int	cmu_kfc_spare3;
+	unsigned int	cmu_kfc_spare4;
+	unsigned char	res148[0x1fdc];
+	unsigned int	cmu_kfc_version;		/* 0x1003bff0 */
+};
+
 /* structure for epll configuration used in audio clock configuration */
 struct set_epll_con_val {
 	unsigned int freq_out;		/* frequency out */
