Message ID | 20230211152909.1436133-1-linus.walleij@linaro.org |
---|---|
Headers | show |
Series | Backport BRCMNAND changes from Linux | expand |
Hi Linus. On 02/11/2023 07:28 AM, Linus Walleij wrote: > Hunting down a bug on my system I took to back-porting > all reasonable changes from the Linux brcmnand driver that > were not yet in the U-Boot derivative. > > I noticed that a simple diff -ur between brcmnand.c > between the file in Linux and U-Boot was possible to see > what differs. Combining this with some git log --oneline > manual comparison, fuzzing and manual intervention I > backported a set of relevant patches from Linux that > compiles and WorksForMe(TM). > > The diff between Linux and U-Boot is much smaller after > this, the main missing part are subsystem cosmetics > changes and the EDU DMA mode support. > > This was as much as I could bite off in one go. > > All patches countersigned-off and marked as [backported]. > > ChangeLog v1->v2: > - Drop the patch to use the new OOB data layout helpers > "mtd: nand: brcm: switch to mtd_ooblayout_ops" > - Drop all patches depending on the previous patch, in > total 4 patches. > > Claire Lin (1): > mtd: rawnand: brcmnand: Fix ecc chunk calculation for erased page > bitfips > > Kamal Dasu (3): > mtd: rawnand: brcmnand: Refactored code to introduce helper functions > mtd: rawnand: brcmnand: Add support for v7.3 controller > mtd: nand: brcmnand: Add support for flash-dma v0 > > Álvaro Fernández Rojas (6): > mtd: rawnand: brcmnand: correctly verify erased pages > mtd: rawnand: brcmnand: rename v4 registers > mtd: rawnand: brcmnand: fix CS0 layout > mtd: rawnand: brcmnand: rename page sizes > mtd: rawnand: brcmnand: support v2.1-v2.2 controllers > mtd: rawnand: brcmnand: fix OOB R/W with Hamming ECC > > drivers/mtd/nand/raw/brcmnand/brcmnand.c | 353 +++++++++++++++++------ > 1 file changed, 268 insertions(+), 85 deletions(-) > Sorry for the delay. Finally I got some time to try your patches on a BCM63158 based board with NAND controller 7.1. It works fine.
Hi On Wed, Feb 22, 2023 at 2:28 AM William Zhang <william.zhang@broadcom.com> wrote: > > Hi Linus. > > On 02/11/2023 07:28 AM, Linus Walleij wrote: > > Hunting down a bug on my system I took to back-porting > > all reasonable changes from the Linux brcmnand driver that > > were not yet in the U-Boot derivative. > > > > I noticed that a simple diff -ur between brcmnand.c > > between the file in Linux and U-Boot was possible to see > > what differs. Combining this with some git log --oneline > > manual comparison, fuzzing and manual intervention I > > backported a set of relevant patches from Linux that > > compiles and WorksForMe(TM). > > > > The diff between Linux and U-Boot is much smaller after > > this, the main missing part are subsystem cosmetics > > changes and the EDU DMA mode support. > > > > This was as much as I could bite off in one go. > > > > All patches countersigned-off and marked as [backported]. > > > > ChangeLog v1->v2: > > - Drop the patch to use the new OOB data layout helpers > > "mtd: nand: brcm: switch to mtd_ooblayout_ops" > > - Drop all patches depending on the previous patch, in > > total 4 patches. > > > > Claire Lin (1): > > mtd: rawnand: brcmnand: Fix ecc chunk calculation for erased page > > bitfips > > > > Kamal Dasu (3): > > mtd: rawnand: brcmnand: Refactored code to introduce helper functions > > mtd: rawnand: brcmnand: Add support for v7.3 controller > > mtd: nand: brcmnand: Add support for flash-dma v0 > > > > Álvaro Fernández Rojas (6): > > mtd: rawnand: brcmnand: correctly verify erased pages > > mtd: rawnand: brcmnand: rename v4 registers > > mtd: rawnand: brcmnand: fix CS0 layout > > mtd: rawnand: brcmnand: rename page sizes > > mtd: rawnand: brcmnand: support v2.1-v2.2 controllers > > mtd: rawnand: brcmnand: fix OOB R/W with Hamming ECC > > > > drivers/mtd/nand/raw/brcmnand/brcmnand.c | 353 +++++++++++++++++------ > > 1 file changed, 268 insertions(+), 85 deletions(-) > > > > Sorry for the delay. Finally I got some time to try your patches on a > BCM63158 based board with NAND controller 7.1. It works fine. We will queue this week, thank you Michael