mbox series

[v7,00/22] RISC-V SiFive FU540 support SPL

Message ID 20200502100628.24809-1-pragnesh.patel@sifive.com
Headers show
Series RISC-V SiFive FU540 support SPL | expand

Message

Pragnesh Patel May 2, 2020, 10:06 a.m. UTC
This series add support for SPL to FU540.U-Boot SPL can boot from
L2 LIM (0x0800_0000) and jump to OpenSBI(FW_DYNAMIC firmware) and
U-Boot proper from MMC devices.

How to test this patch:
1) Go to OpenSBI-dir : make PLATFORM=generic FW_DYNAMIC=y
2) export OPENSBI=<path/to/opensbi/install_dir/platform/generic/firmware/fw_dynamic.bin>
3) Change to u-boot-dir
4) make sifive_fu540_defconfig
5) make all
6) Format the SD card (make sure the disk has GPT, otherwise use gdisk to switch)

	# sudo sgdisk --clear \
	> --set-alignment=2 \
	> --new=1:34:2081 --change-name=1:loader1 --typecode=1:5B193300-FC78-40CD-8002-E86C45580B47 \
	> --new=2:2082:10273 --change-name=2:loader2 --typecode=2:2E54B353-1271-4842-806F-E436D6AF6985 \
	> --new=3:10274: --change-name=3:rootfs --typecode=3:0FC63DAF-8483-4772-8E79-3D69D8477DE4 \
	> /dev/sda

7) sudo dd if=spl/u-boot-spl.bin of=/dev/sda seek=34
8) sudo dd if=u-boot.itb of=/dev/sda seek=2082 


Changes in v7:
- Standardize SD gpt partition layout
- Add delay for SiFive OTP driver
- Use DM way for corepll and ddrpll
- Add new cpu fu540 (arch/riscv/cpu/fu540)
- Update document for FU540 (doc/board/sifive/fu540.rst)

Changes in v6:
- Typo Correction
- Make fu540-c000-u-boot.dtsi and hifive-unleashed-a00-u-boot.dtsi
  Dual Licensed
- Sync Hifive unleashed dts from Linux
- Add arch/riscv/fu540 for FU540 specific code

Changes in v5:
- Return read/write bytes for sifive_otp_read and sifive_otp_write
- Correct Palmer's email address

Changes in v4:
- Split misc DM driver patch into multiple patches
- Added new SPL_CRC7_SUPPORT Kconfig option
- Added DM driver for DDR
- Added clk_enable and clk_disable ops in SiFive PRCI driver
- Added early clock initialization for SPL in SiFive PRCI driver
- Added SPL config options in sifive_fu540_defconfig instead of
  creatiing a new config file for SPL
- Update fu540.rst on how to build and flash U-boot SPL

Changes in v3:
- Remove arch-fu540 and arch-sifive from arch/riscv/include/asm/
- Split SPL patches into DDR and SPL and spl defconfig
- Update fu540/MAINTAINERS file
- Update fu540.rst on how to build and flash U-boot SPL

Changes in v2:
- Add DM driver Sifive OTP
- Split SPL patches into multiple patches
- Add a seprate patch for _image_binary_end and crc7.c
- Add a seprate patch to add board -u-boot.dtsi files
- Update FU540 RISC-V documentation


Pragnesh Patel (22):
  misc: add driver for the SiFive otp controller
  riscv: sifive: fu540: Use OTP DM driver for serial environment
    variable
  riscv: Add _image_binary_end for SPL
  lib: Makefile: build crc7.c when CONFIG_MMC_SPI
  riscv: sifive: dts: fu540: Add board -u-boot.dtsi files
  sifive: fu540: add ddr driver
  sifive: dts: fu540: Add DDR controller and phy register settings
  riscv: sifive: dts: fu540: add U-Boot dmc node
  clk: sifive: fu540-prci: Add clock enable and disable ops
  clk: sifive: fu540-prci: ddr and ethernet clock initialization in SPL
  riscv: dts: sifive: Sync hifive-unleashed-a00 dts from linux
  sifive: dts: fu540: Enable gpio in U-Boot SPL
  riscv: cpu: fu540: Add support for cpu fu540
  riscv: Add place-holder for driver compilation
  riscv: sifive: dts: fu540: Add clock for cpus node
  riscv: Enable cpu clock if it is present
  riscv: sifive: fu540: add SPL configuration
  configs: fu540: Add config options for U-Boot SPL
  sifive: dts: fu540: Enable L2 Cache in U-Boot
  riscv: sifive: fu540: enable all cache ways from U-Boot proper
  doc: sifive: fu540: Add description for OpenSBI generic platform
  doc: sifive: fu540: Add description for RISC-V FU540 U-Boot SPL

 arch/riscv/Kconfig                            |    1 +
 arch/riscv/cpu/fu540/Kconfig                  |   15 +
 arch/riscv/cpu/fu540/Makefile                 |   12 +
 arch/riscv/cpu/fu540/cache.c                  |   53 +
 arch/riscv/cpu/fu540/cpu.c                    |   22 +
 arch/riscv/cpu/fu540/dram.c                   |   38 +
 arch/riscv/cpu/fu540/spl.c                    |   23 +
 arch/riscv/cpu/u-boot-spl.lds                 |    1 +
 arch/riscv/dts/fu540-c000-u-boot.dtsi         |   91 +
 arch/riscv/dts/fu540-c000.dtsi                |   37 +-
 ...fu540-hifive-unleashed-a00-sdram-ddr4.dtsi | 1489 +++++++++++++++++
 .../dts/hifive-unleashed-a00-u-boot.dtsi      |   22 +
 arch/riscv/dts/hifive-unleashed-a00.dts       |    9 +
 arch/riscv/include/asm/arch-fu540/cache.h     |   14 +
 arch/riscv/include/asm/arch-fu540/clk.h       |   14 +
 arch/riscv/include/asm/arch-fu540/gpio.h      |   38 +
 arch/riscv/include/asm/arch-fu540/spl.h       |   14 +
 board/sifive/fu540/Kconfig                    |   14 +-
 board/sifive/fu540/Makefile                   |    4 +
 board/sifive/fu540/fu540.c                    |  143 +-
 board/sifive/fu540/spl.c                      |   72 +
 common/spl/Kconfig                            |    6 +
 configs/sifive_fu540_defconfig                |    9 +
 doc/board/sifive/fu540.rst                    |  395 ++++-
 drivers/clk/sifive/fu540-prci.c               |  193 ++-
 drivers/cpu/riscv_cpu.c                       |   33 +
 drivers/misc/Kconfig                          |    7 +
 drivers/misc/Makefile                         |    1 +
 drivers/misc/sifive-otp.c                     |  273 +++
 drivers/mmc/Kconfig                           |    1 +
 drivers/ram/Kconfig                           |    1 +
 drivers/ram/Makefile                          |    2 +
 drivers/ram/sifive/Kconfig                    |   13 +
 drivers/ram/sifive/Makefile                   |    6 +
 drivers/ram/sifive/sdram_fu540.c              |  416 +++++
 include/configs/sifive-fu540.h                |   18 +
 lib/Makefile                                  |    1 +
 37 files changed, 3403 insertions(+), 98 deletions(-)
 create mode 100644 arch/riscv/cpu/fu540/Kconfig
 create mode 100644 arch/riscv/cpu/fu540/Makefile
 create mode 100644 arch/riscv/cpu/fu540/cache.c
 create mode 100644 arch/riscv/cpu/fu540/cpu.c
 create mode 100644 arch/riscv/cpu/fu540/dram.c
 create mode 100644 arch/riscv/cpu/fu540/spl.c
 create mode 100644 arch/riscv/dts/fu540-c000-u-boot.dtsi
 create mode 100644 arch/riscv/dts/fu540-hifive-unleashed-a00-sdram-ddr4.dtsi
 create mode 100644 arch/riscv/include/asm/arch-fu540/cache.h
 create mode 100644 arch/riscv/include/asm/arch-fu540/clk.h
 create mode 100644 arch/riscv/include/asm/arch-fu540/gpio.h
 create mode 100644 arch/riscv/include/asm/arch-fu540/spl.h
 create mode 100644 board/sifive/fu540/spl.c
 create mode 100644 drivers/misc/sifive-otp.c
 create mode 100644 drivers/ram/sifive/Kconfig
 create mode 100644 drivers/ram/sifive/Makefile
 create mode 100644 drivers/ram/sifive/sdram_fu540.c

Comments

Jagan Teki May 2, 2020, 5:18 p.m. UTC | #1
On Sat, May 2, 2020 at 3:37 PM Pragnesh Patel <pragnesh.patel at sifive.com> wrote:
>
> This series add support for SPL to FU540.U-Boot SPL can boot from
> L2 LIM (0x0800_0000) and jump to OpenSBI(FW_DYNAMIC firmware) and
> U-Boot proper from MMC devices.
>
> How to test this patch:
> 1) Go to OpenSBI-dir : make PLATFORM=generic FW_DYNAMIC=y
> 2) export OPENSBI=<path/to/opensbi/install_dir/platform/generic/firmware/fw_dynamic.bin>
> 3) Change to u-boot-dir
> 4) make sifive_fu540_defconfig
> 5) make all
> 6) Format the SD card (make sure the disk has GPT, otherwise use gdisk to switch)
>
>         # sudo sgdisk --clear \
>         > --set-alignment=2 \
>         > --new=1:34:2081 --change-name=1:loader1 --typecode=1:5B193300-FC78-40CD-8002-E86C45580B47 \
>         > --new=2:2082:10273 --change-name=2:loader2 --typecode=2:2E54B353-1271-4842-806F-E436D6AF6985 \
>         > --new=3:10274: --change-name=3:rootfs --typecode=3:0FC63DAF-8483-4772-8E79-3D69D8477DE4 \
>         > /dev/sda
>
> 7) sudo dd if=spl/u-boot-spl.bin of=/dev/sda seek=34
> 8) sudo dd if=u-boot.itb of=/dev/sda seek=2082

Most patches improved from v6, but still few issues like
- patches which are unrelated to MMC SPL support, please bypass and
send them separately.
- order of patches need to improve, take my suggestions and order them.
- incorporate partition layout patches before SPL enablement patch.

Jagan.
Pragnesh Patel May 3, 2020, 7:19 a.m. UTC | #2
Hi Jagan,

>-----Original Message-----
>From: Jagan Teki <jagan at amarulasolutions.com>
>Sent: 02 May 2020 22:49
>To: Pragnesh Patel <pragnesh.patel at sifive.com>
>Cc: U-Boot-Denx <u-boot at lists.denx.de>; Atish Patra
><atish.patra at wdc.com>; Palmer Dabbelt <palmerdabbelt at google.com>; Bin
>Meng <bmeng.cn at gmail.com>; Paul Walmsley <paul.walmsley at sifive.com>;
>Troy Benjegerdes <troy.benjegerdes at sifive.com>; Anup Patel
><anup.patel at wdc.com>; Sagar Kadam <sagar.kadam at sifive.com>; Rick Chen
><rick at andestech.com>
>Subject: Re: [PATCH v7 00/22] RISC-V SiFive FU540 support SPL
>
>[External Email] Do not click links or attachments unless you recognize the
>sender and know the content is safe
>
>On Sat, May 2, 2020 at 3:37 PM Pragnesh Patel <pragnesh.patel at sifive.com>
>wrote:
>>
>> This series add support for SPL to FU540.U-Boot SPL can boot from
>> L2 LIM (0x0800_0000) and jump to OpenSBI(FW_DYNAMIC firmware) and
>> U-Boot proper from MMC devices.
>>
>> How to test this patch:
>> 1) Go to OpenSBI-dir : make PLATFORM=generic FW_DYNAMIC=y
>> 2) export
>> OPENSBI=<path/to/opensbi/install_dir/platform/generic/firmware/fw_dyna
>> mic.bin>
>> 3) Change to u-boot-dir
>> 4) make sifive_fu540_defconfig
>> 5) make all
>> 6) Format the SD card (make sure the disk has GPT, otherwise use gdisk
>> to switch)
>>
>>         # sudo sgdisk --clear \
>>         > --set-alignment=2 \
>>         > --new=1:34:2081 --change-name=1:loader1 --typecode=1:5B193300-
>FC78-40CD-8002-E86C45580B47 \
>>         > --new=2:2082:10273 --change-name=2:loader2 --
>typecode=2:2E54B353-1271-4842-806F-E436D6AF6985 \
>>         > --new=3:10274: --change-name=3:rootfs --typecode=3:0FC63DAF-
>8483-4772-8E79-3D69D8477DE4 \
>>         > /dev/sda
>>
>> 7) sudo dd if=spl/u-boot-spl.bin of=/dev/sda seek=34
>> 8) sudo dd if=u-boot.itb of=/dev/sda seek=2082
>
>Most patches improved from v6, but still few issues like
>- patches which are unrelated to MMC SPL support, please bypass and send
>them separately.

Will update in v8.

>- order of patches need to improve, take my suggestions and order them.

Sure.

>- incorporate partition layout patches before SPL enablement patch.

Will do, I thought you will send v3 of [1] that's why I did not incorporate that changes.
I will incorporate in v8.

[1]
https://patchwork.amarulasolutions.com/patch/1092/

>
>Jagan.