This patch series adds support for ClearFog Base static configuration,
as well as updating and fixing the ClearFog support for MMC and SPI
booting.
v2 changes:
- updated against, and dependent on, https://patchwork.ozlabs.org/cover/1200324
v3 changes:
- rebased against ClearFog runtime TLV EEPROM changes merged into mvebu/master
v4
- adjust static SerDes configuration at runtime instead of #ifdef
v5
- distinguish build-only config changes (SFP and PCIe/SATA) from
runtime detectable config changes
- retested SATA mode in PCIe slot with swap rx changes, confirmed
working as presently patched. Only tested with ClearFog Base which
only provides single channel, but Pro mechanism is parallel.
v6
- address minor review feedback
Joel Johnson (12):
arm: mvebu: fix SerDes table alignment
arm: mvebu: solidrun: remove hardcoded DTS MAC address
arm: mvebu: clearfog: use Pro name by default
arm: mvebu: clearfog: initial ClearFog Base variant
arm: mvebu: clearfog: Add option for 2.5 Gbps SFP
arm: mvebu: clearfog: Add SATA mode flags
arm: mvebu: clearfog: Unify DT selection paths
arm: mvebu: clearfog: add SPI offsets
arm: mvebu: enable working default boot support
arm: mvebu: clearfog: move ENV params to Kconfig
arm: mvebu: clearfog: don't always use SPL MMC
arm: mvebu: clearfog: Use Pro DT by default
.../arm/dts/armada-38x-solidrun-microsom.dtsi | 1 -
arch/arm/mach-mvebu/Kconfig | 13 ++++
.../serdes/a38x/high_speed_env_spec.c | 6 +-
board/solidrun/clearfog/Kconfig | 62 +++++++++++++++++++
board/solidrun/clearfog/clearfog.c | 61 +++++++++++++++---
configs/clearfog_defconfig | 4 --
include/configs/clearfog.h | 1 -
7 files changed, 132 insertions(+), 16 deletions(-)
create mode 100644 board/solidrun/clearfog/Kconfig
This patch series adds support for ClearFog Base static configuration, as well as updating and fixing the ClearFog support for MMC and SPI booting. v2 changes: - updated against, and dependent on, https://patchwork.ozlabs.org/cover/1200324 v3 changes: - rebased against ClearFog runtime TLV EEPROM changes merged into mvebu/master v4 - adjust static SerDes configuration at runtime instead of #ifdef v5 - distinguish build-only config changes (SFP and PCIe/SATA) from runtime detectable config changes - retested SATA mode in PCIe slot with swap rx changes, confirmed working as presently patched. Only tested with ClearFog Base which only provides single channel, but Pro mechanism is parallel. v6 - address minor review feedback Joel Johnson (12): arm: mvebu: fix SerDes table alignment arm: mvebu: solidrun: remove hardcoded DTS MAC address arm: mvebu: clearfog: use Pro name by default arm: mvebu: clearfog: initial ClearFog Base variant arm: mvebu: clearfog: Add option for 2.5 Gbps SFP arm: mvebu: clearfog: Add SATA mode flags arm: mvebu: clearfog: Unify DT selection paths arm: mvebu: clearfog: add SPI offsets arm: mvebu: enable working default boot support arm: mvebu: clearfog: move ENV params to Kconfig arm: mvebu: clearfog: don't always use SPL MMC arm: mvebu: clearfog: Use Pro DT by default .../arm/dts/armada-38x-solidrun-microsom.dtsi | 1 - arch/arm/mach-mvebu/Kconfig | 13 ++++ .../serdes/a38x/high_speed_env_spec.c | 6 +- board/solidrun/clearfog/Kconfig | 62 +++++++++++++++++++ board/solidrun/clearfog/clearfog.c | 61 +++++++++++++++--- configs/clearfog_defconfig | 4 -- include/configs/clearfog.h | 1 - 7 files changed, 132 insertions(+), 16 deletions(-) create mode 100644 board/solidrun/clearfog/Kconfig