Index: linux/include/uapi/linux/cyclades.h
===================================================================
--- /dev/null
+++ linux/include/uapi/linux/cyclades.h
@@ -0,0 +1,494 @@
+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/* $Revision: 3.0 $$Date: 1998/11/02 14:20:59 $
+ * linux/include/linux/cyclades.h
+ *
+ * This file was initially written by
+ * Randolph Bentson <bentson@grieg.seaslug.org> and is maintained by
+ * Ivan Passos <ivan@cyclades.com>.
+ *
+ * This file contains the general definitions for the cyclades.c driver
+ *$Log: cyclades.h,v $
+ *Revision 3.1  2002/01/29 11:36:16  henrique
+ *added throttle field on struct cyclades_port to indicate whether the
+ *port is throttled or not
+ *
+ *Revision 3.1  2000/04/19 18:52:52  ivan
+ *converted address fields to unsigned long and added fields for physical
+ *addresses on cyclades_card structure;
+ *
+ *Revision 3.0  1998/11/02 14:20:59  ivan
+ *added nports field on cyclades_card structure;
+ *
+ *Revision 2.5  1998/08/03 16:57:01  ivan
+ *added cyclades_idle_stats structure;
+ *
+ *Revision 2.4  1998/06/01 12:09:53  ivan
+ *removed closing_wait2 from cyclades_port structure;
+ *
+ *Revision 2.3  1998/03/16 18:01:12  ivan
+ *changes in the cyclades_port structure to get it closer to the
+ *standard serial port structure;
+ *added constants for new ioctls;
+ *
+ *Revision 2.2  1998/02/17 16:50:00  ivan
+ *changes in the cyclades_port structure (addition of shutdown_wait and
+ *chip_rev variables);
+ *added constants for new ioctls and for CD1400 rev. numbers.
+ *
+ *Revision 2.1	1997/10/24 16:03:00  ivan
+ *added rflow (which allows enabling the CD1400 special flow control
+ *feature) and rtsdtr_inv (which allows DTR/RTS pin inversion) to
+ *cyclades_port structure;
+ *added Alpha support
+ *
+ *Revision 2.0  1997/06/30 10:30:00  ivan
+ *added some new doorbell command constants related to IOCTLW and
+ *UART error signaling
+ *
+ *Revision 1.8  1997/06/03 15:30:00  ivan
+ *added constant ZFIRM_HLT
+ *added constant CyPCI_Ze_win ( = 2 * Cy_PCI_Zwin)
+ *
+ *Revision 1.7  1997/03/26 10:30:00  daniel
+ *new entries at the end of cyclades_port struct to reallocate
+ *variables illegally allocated within card memory.
+ *
+ *Revision 1.6  1996/09/09 18:35:30  bentson
+ *fold in changes for Cyclom-Z -- including structures for
+ *communicating with board as well modest changes to original
+ *structures to support new features.
+ *
+ *Revision 1.5  1995/11/13 21:13:31  bentson
+ *changes suggested by Michael Chastain <mec@duracef.shout.net>
+ *to support use of this file in non-kernel applications
+ *
+ *
+ */
+
+#ifndef _UAPI_LINUX_CYCLADES_H
+#define _UAPI_LINUX_CYCLADES_H
+
+#include <linux/types.h>
+
+struct cyclades_monitor {
+        unsigned long           int_count;
+        unsigned long           char_count;
+        unsigned long           char_max;
+        unsigned long           char_last;
+};
+
+/*
+ * These stats all reflect activity since the device was last initialized.
+ * (i.e., since the port was opened with no other processes already having it
+ * open)
+ */
+struct cyclades_idle_stats {
+    __kernel_old_time_t in_use;	/* Time device has been in use (secs) */
+    __kernel_old_time_t recv_idle; /* Time since last char received (secs) */
+    __kernel_old_time_t xmit_idle; /* Time since last char transmitted (secs) */
+    unsigned long  recv_bytes;	/* Bytes received */
+    unsigned long  xmit_bytes;	/* Bytes transmitted */
+    unsigned long  overruns;	/* Input overruns */
+    unsigned long  frame_errs;	/* Input framing errors */
+    unsigned long  parity_errs;	/* Input parity errors */
+};
+
+#define CYCLADES_MAGIC  0x4359
+
+#define CYGETMON                0x435901
+#define CYGETTHRESH             0x435902
+#define CYSETTHRESH             0x435903
+#define CYGETDEFTHRESH          0x435904
+#define CYSETDEFTHRESH          0x435905
+#define CYGETTIMEOUT            0x435906
+#define CYSETTIMEOUT            0x435907
+#define CYGETDEFTIMEOUT         0x435908
+#define CYSETDEFTIMEOUT         0x435909
+#define CYSETRFLOW		0x43590a
+#define CYGETRFLOW		0x43590b
+#define CYSETRTSDTR_INV		0x43590c
+#define CYGETRTSDTR_INV		0x43590d
+#define CYZSETPOLLCYCLE		0x43590e
+#define CYZGETPOLLCYCLE		0x43590f
+#define CYGETCD1400VER		0x435910
+#define	CYSETWAIT		0x435912
+#define	CYGETWAIT		0x435913
+
+/*************** CYCLOM-Z ADDITIONS ***************/
+
+#define CZIOC           ('M' << 8)
+#define CZ_NBOARDS      (CZIOC|0xfa)
+#define CZ_BOOT_START   (CZIOC|0xfb)
+#define CZ_BOOT_DATA    (CZIOC|0xfc)
+#define CZ_BOOT_END     (CZIOC|0xfd)
+#define CZ_TEST         (CZIOC|0xfe)
+
+#define CZ_DEF_POLL	(HZ/25)
+
+#define MAX_BOARD       4       /* Max number of boards */
+#define MAX_DEV         256     /* Max number of ports total */
+#define	CYZ_MAX_SPEED	921600
+
+#define	CYZ_FIFO_SIZE	16
+
+#define CYZ_BOOT_NWORDS 0x100
+struct CYZ_BOOT_CTRL {
+        unsigned short  nboard;
+        int             status[MAX_BOARD];
+        int             nchannel[MAX_BOARD];
+        int             fw_rev[MAX_BOARD];
+        unsigned long   offset;
+        unsigned long   data[CYZ_BOOT_NWORDS];
+};
+
+
+#ifndef DP_WINDOW_SIZE
+/*
+ *	Memory Window Sizes
+ */
+
+#define	DP_WINDOW_SIZE		(0x00080000)	/* window size 512 Kb */
+#define	ZE_DP_WINDOW_SIZE	(0x00100000)	/* window size 1 Mb (Ze and
+						  8Zo V.2 */
+#define	CTRL_WINDOW_SIZE	(0x00000080)	/* runtime regs 128 bytes */
+
+/*
+ *	CUSTOM_REG - Cyclom-Z/PCI Custom Registers Set. The driver
+ *	normally will access only interested on the fpga_id, fpga_version,
+ *	start_cpu and stop_cpu.
+ */
+
+struct	CUSTOM_REG {
+	__u32	fpga_id;		/* FPGA Identification Register */
+	__u32	fpga_version;		/* FPGA Version Number Register */
+	__u32	cpu_start;		/* CPU start Register (write) */
+	__u32	cpu_stop;		/* CPU stop Register (write) */
+	__u32	misc_reg;		/* Miscellaneous Register */
+	__u32	idt_mode;		/* IDT mode Register */
+	__u32	uart_irq_status;	/* UART IRQ status Register */
+	__u32	clear_timer0_irq;	/* Clear timer interrupt Register */
+	__u32	clear_timer1_irq;	/* Clear timer interrupt Register */
+	__u32	clear_timer2_irq;	/* Clear timer interrupt Register */
+	__u32	test_register;		/* Test Register */
+	__u32	test_count;		/* Test Count Register */
+	__u32	timer_select;		/* Timer select register */
+	__u32	pr_uart_irq_status;	/* Prioritized UART IRQ stat Reg */
+	__u32	ram_wait_state;		/* RAM wait-state Register */
+	__u32	uart_wait_state;	/* UART wait-state Register */
+	__u32	timer_wait_state;	/* timer wait-state Register */
+	__u32	ack_wait_state;		/* ACK wait State Register */
+};
+
+/*
+ *	RUNTIME_9060 - PLX PCI9060ES local configuration and shared runtime
+ *	registers. This structure can be used to access the 9060 registers
+ *	(memory mapped).
+ */
+
+struct RUNTIME_9060 {
+	__u32	loc_addr_range;	/* 00h - Local Address Range */
+	__u32	loc_addr_base;	/* 04h - Local Address Base */
+	__u32	loc_arbitr;	/* 08h - Local Arbitration */
+	__u32	endian_descr;	/* 0Ch - Big/Little Endian Descriptor */
+	__u32	loc_rom_range;	/* 10h - Local ROM Range */
+	__u32	loc_rom_base;	/* 14h - Local ROM Base */
+	__u32	loc_bus_descr;	/* 18h - Local Bus descriptor */
+	__u32	loc_range_mst;	/* 1Ch - Local Range for Master to PCI */
+	__u32	loc_base_mst;	/* 20h - Local Base for Master PCI */
+	__u32	loc_range_io;	/* 24h - Local Range for Master IO */
+	__u32	pci_base_mst;	/* 28h - PCI Base for Master PCI */
+	__u32	pci_conf_io;	/* 2Ch - PCI configuration for Master IO */
+	__u32	filler1;	/* 30h */
+	__u32	filler2;	/* 34h */
+	__u32	filler3;	/* 38h */
+	__u32	filler4;	/* 3Ch */
+	__u32	mail_box_0;	/* 40h - Mail Box 0 */
+	__u32	mail_box_1;	/* 44h - Mail Box 1 */
+	__u32	mail_box_2;	/* 48h - Mail Box 2 */
+	__u32	mail_box_3;	/* 4Ch - Mail Box 3 */
+	__u32	filler5;	/* 50h */
+	__u32	filler6;	/* 54h */
+	__u32	filler7;	/* 58h */
+	__u32	filler8;	/* 5Ch */
+	__u32	pci_doorbell;	/* 60h - PCI to Local Doorbell */
+	__u32	loc_doorbell;	/* 64h - Local to PCI Doorbell */
+	__u32	intr_ctrl_stat;	/* 68h - Interrupt Control/Status */
+	__u32	init_ctrl;	/* 6Ch - EEPROM control, Init Control, etc */
+};
+
+/* Values for the Local Base Address re-map register */
+
+#define	WIN_RAM		0x00000001L	/* set the sliding window to RAM */
+#define	WIN_CREG	0x14000001L	/* set the window to custom Registers */
+
+/* Values timer select registers */
+
+#define	TIMER_BY_1M	0x00		/* clock divided by 1M */
+#define	TIMER_BY_256K	0x01		/* clock divided by 256k */
+#define	TIMER_BY_128K	0x02		/* clock divided by 128k */
+#define	TIMER_BY_32K	0x03		/* clock divided by 32k */
+
+/****************** ****************** *******************/
+#endif
+
+#ifndef ZFIRM_ID
+/* #include "zfwint.h" */
+/****************** ****************** *******************/
+/*
+ *	This file contains the definitions for interfacing with the
+ *	Cyclom-Z ZFIRM Firmware.
+ */
+
+/* General Constant definitions */
+
+#define	MAX_CHAN	64		/* max number of channels per board */
+
+/* firmware id structure (set after boot) */
+
+#define ID_ADDRESS	0x00000180L	/* signature/pointer address */
+#define	ZFIRM_ID	0x5557465AL	/* ZFIRM/U signature */
+#define	ZFIRM_HLT	0x59505B5CL	/* ZFIRM needs external power supply */
+#define	ZFIRM_RST	0x56040674L	/* RST signal (due to FW reset) */
+
+#define	ZF_TINACT_DEF	1000		/* default inactivity timeout
+					   (1000 ms) */
+#define	ZF_TINACT	ZF_TINACT_DEF
+
+struct	FIRM_ID {
+	__u32	signature;		/* ZFIRM/U signature */
+	__u32	zfwctrl_addr;		/* pointer to ZFW_CTRL structure */
+};
+
+/* Op. System id */
+
+#define	C_OS_LINUX	0x00000030	/* generic Linux system */
+
+/* channel op_mode */
+
+#define	C_CH_DISABLE	0x00000000	/* channel is disabled */
+#define	C_CH_TXENABLE	0x00000001	/* channel Tx enabled */
+#define	C_CH_RXENABLE	0x00000002	/* channel Rx enabled */
+#define	C_CH_ENABLE	0x00000003	/* channel Tx/Rx enabled */
+#define	C_CH_LOOPBACK	0x00000004	/* Loopback mode */
+
+/* comm_parity - parity */
+
+#define	C_PR_NONE	0x00000000	/* None */
+#define	C_PR_ODD	0x00000001	/* Odd */
+#define C_PR_EVEN	0x00000002	/* Even */
+#define C_PR_MARK	0x00000004	/* Mark */
+#define C_PR_SPACE	0x00000008	/* Space */
+#define C_PR_PARITY	0x000000ff
+
+#define	C_PR_DISCARD	0x00000100	/* discard char with frame/par error */
+#define C_PR_IGNORE	0x00000200	/* ignore frame/par error */
+
+/* comm_data_l - data length and stop bits */
+
+#define C_DL_CS5	0x00000001
+#define C_DL_CS6	0x00000002
+#define C_DL_CS7	0x00000004
+#define C_DL_CS8	0x00000008
+#define	C_DL_CS		0x0000000f
+#define C_DL_1STOP	0x00000010
+#define C_DL_15STOP	0x00000020
+#define C_DL_2STOP	0x00000040
+#define	C_DL_STOP	0x000000f0
+
+/* interrupt enabling/status */
+
+#define	C_IN_DISABLE	0x00000000	/* zero, disable interrupts */
+#define	C_IN_TXBEMPTY	0x00000001	/* tx buffer empty */
+#define	C_IN_TXLOWWM	0x00000002	/* tx buffer below LWM */
+#define	C_IN_RXHIWM	0x00000010	/* rx buffer above HWM */
+#define	C_IN_RXNNDT	0x00000020	/* rx no new data timeout */
+#define	C_IN_MDCD	0x00000100	/* modem DCD change */
+#define	C_IN_MDSR	0x00000200	/* modem DSR change */
+#define	C_IN_MRI	0x00000400	/* modem RI change */
+#define	C_IN_MCTS	0x00000800	/* modem CTS change */
+#define	C_IN_RXBRK	0x00001000	/* Break received */
+#define	C_IN_PR_ERROR	0x00002000	/* parity error */
+#define	C_IN_FR_ERROR	0x00004000	/* frame error */
+#define C_IN_OVR_ERROR  0x00008000      /* overrun error */
+#define C_IN_RXOFL	0x00010000      /* RX buffer overflow */
+#define C_IN_IOCTLW	0x00020000      /* I/O control w/ wait */
+#define C_IN_MRTS	0x00040000	/* modem RTS drop */
+#define C_IN_ICHAR	0x00080000
+
+/* flow control */
+
+#define	C_FL_OXX	0x00000001	/* output Xon/Xoff flow control */
+#define	C_FL_IXX	0x00000002	/* output Xon/Xoff flow control */
+#define C_FL_OIXANY	0x00000004	/* output Xon/Xoff (any xon) */
+#define	C_FL_SWFLOW	0x0000000f
+
+/* flow status */
+
+#define	C_FS_TXIDLE	0x00000000	/* no Tx data in the buffer or UART */
+#define	C_FS_SENDING	0x00000001	/* UART is sending data */
+#define	C_FS_SWFLOW	0x00000002	/* Tx is stopped by received Xoff */
+
+/* rs_control/rs_status RS-232 signals */
+
+#define C_RS_PARAM	0x80000000	/* Indicates presence of parameter in
+					   IOCTLM command */
+#define	C_RS_RTS	0x00000001	/* RTS */
+#define	C_RS_DTR	0x00000004	/* DTR */
+#define	C_RS_DCD	0x00000100	/* CD */
+#define	C_RS_DSR	0x00000200	/* DSR */
+#define	C_RS_RI		0x00000400	/* RI */
+#define	C_RS_CTS	0x00000800	/* CTS */
+
+/* commands Host <-> Board */
+
+#define	C_CM_RESET	0x01		/* reset/flush buffers */
+#define	C_CM_IOCTL	0x02		/* re-read CH_CTRL */
+#define	C_CM_IOCTLW	0x03		/* re-read CH_CTRL, intr when done */
+#define	C_CM_IOCTLM	0x04		/* RS-232 outputs change */
+#define	C_CM_SENDXOFF	0x10		/* send Xoff */
+#define	C_CM_SENDXON	0x11		/* send Xon */
+#define C_CM_CLFLOW	0x12		/* Clear flow control (resume) */
+#define	C_CM_SENDBRK	0x41		/* send break */
+#define	C_CM_INTBACK	0x42		/* Interrupt back */
+#define	C_CM_SET_BREAK	0x43		/* Tx break on */
+#define	C_CM_CLR_BREAK	0x44		/* Tx break off */
+#define	C_CM_CMD_DONE	0x45		/* Previous command done */
+#define C_CM_INTBACK2	0x46		/* Alternate Interrupt back */
+#define	C_CM_TINACT	0x51		/* set inactivity detection */
+#define	C_CM_IRQ_ENBL	0x52		/* enable generation of interrupts */
+#define	C_CM_IRQ_DSBL	0x53		/* disable generation of interrupts */
+#define	C_CM_ACK_ENBL	0x54		/* enable acknowledged interrupt mode */
+#define	C_CM_ACK_DSBL	0x55		/* disable acknowledged intr mode */
+#define	C_CM_FLUSH_RX	0x56		/* flushes Rx buffer */
+#define	C_CM_FLUSH_TX	0x57		/* flushes Tx buffer */
+#define C_CM_Q_ENABLE	0x58		/* enables queue access from the
+					   driver */
+#define C_CM_Q_DISABLE  0x59            /* disables queue access from the
+					   driver */
+
+#define	C_CM_TXBEMPTY	0x60		/* Tx buffer is empty */
+#define	C_CM_TXLOWWM	0x61		/* Tx buffer low water mark */
+#define	C_CM_RXHIWM	0x62		/* Rx buffer high water mark */
+#define	C_CM_RXNNDT	0x63		/* rx no new data timeout */
+#define	C_CM_TXFEMPTY	0x64
+#define	C_CM_ICHAR	0x65
+#define	C_CM_MDCD	0x70		/* modem DCD change */
+#define	C_CM_MDSR	0x71		/* modem DSR change */
+#define	C_CM_MRI	0x72		/* modem RI change */
+#define	C_CM_MCTS	0x73		/* modem CTS change */
+#define C_CM_MRTS	0x74		/* modem RTS drop */
+#define	C_CM_RXBRK	0x84		/* Break received */
+#define	C_CM_PR_ERROR	0x85		/* Parity error */
+#define	C_CM_FR_ERROR	0x86		/* Frame error */
+#define C_CM_OVR_ERROR  0x87            /* Overrun error */
+#define C_CM_RXOFL	0x88            /* RX buffer overflow */
+#define	C_CM_CMDERROR	0x90		/* command error */
+#define	C_CM_FATAL	0x91		/* fatal error */
+#define	C_CM_HW_RESET	0x92		/* reset board */
+
+/*
+ *	CH_CTRL - This per port structure contains all parameters
+ *	that control an specific port. It can be seen as the
+ *	configuration registers of a "super-serial-controller".
+ */
+
+struct CH_CTRL {
+	__u32	op_mode;	/* operation mode */
+	__u32	intr_enable;	/* interrupt masking */
+	__u32	sw_flow;	/* SW flow control */
+	__u32	flow_status;	/* output flow status */
+	__u32	comm_baud;	/* baud rate  - numerically specified */
+	__u32	comm_parity;	/* parity */
+	__u32	comm_data_l;	/* data length/stop */
+	__u32	comm_flags;	/* other flags */
+	__u32	hw_flow;	/* HW flow control */
+	__u32	rs_control;	/* RS-232 outputs */
+	__u32	rs_status;	/* RS-232 inputs */
+	__u32	flow_xon;	/* xon char */
+	__u32	flow_xoff;	/* xoff char */
+	__u32	hw_overflow;	/* hw overflow counter */
+	__u32	sw_overflow;	/* sw overflow counter */
+	__u32	comm_error;	/* frame/parity error counter */
+	__u32 ichar;
+	__u32 filler[7];
+};
+
+
+/*
+ *	BUF_CTRL - This per channel structure contains
+ *	all Tx and Rx buffer control for a given channel.
+ */
+
+struct	BUF_CTRL	{
+	__u32	flag_dma;	/* buffers are in Host memory */
+	__u32	tx_bufaddr;	/* address of the tx buffer */
+	__u32	tx_bufsize;	/* tx buffer size */
+	__u32	tx_threshold;	/* tx low water mark */
+	__u32	tx_get;		/* tail index tx buf */
+	__u32	tx_put;		/* head index tx buf */
+	__u32	rx_bufaddr;	/* address of the rx buffer */
+	__u32	rx_bufsize;	/* rx buffer size */
+	__u32	rx_threshold;	/* rx high water mark */
+	__u32	rx_get;		/* tail index rx buf */
+	__u32	rx_put;		/* head index rx buf */
+	__u32	filler[5];	/* filler to align structures */
+};
+
+/*
+ *	BOARD_CTRL - This per board structure contains all global
+ *	control fields related to the board.
+ */
+
+struct BOARD_CTRL {
+
+	/* static info provided by the on-board CPU */
+	__u32	n_channel;	/* number of channels */
+	__u32	fw_version;	/* firmware version */
+
+	/* static info provided by the driver */
+	__u32	op_system;	/* op_system id */
+	__u32	dr_version;	/* driver version */
+
+	/* board control area */
+	__u32	inactivity;	/* inactivity control */
+
+	/* host to FW commands */
+	__u32	hcmd_channel;	/* channel number */
+	__u32	hcmd_param;	/* pointer to parameters */
+
+	/* FW to Host commands */
+	__u32	fwcmd_channel;	/* channel number */
+	__u32	fwcmd_param;	/* pointer to parameters */
+	__u32	zf_int_queue_addr; /* offset for INT_QUEUE structure */
+
+	/* filler so the structures are aligned */
+	__u32	filler[6];
+};
+
+/* Host Interrupt Queue */
+
+#define QUEUE_SIZE	(10*MAX_CHAN)
+
+struct	INT_QUEUE {
+	unsigned char	intr_code[QUEUE_SIZE];
+	unsigned long	channel[QUEUE_SIZE];
+	unsigned long	param[QUEUE_SIZE];
+	unsigned long	put;
+	unsigned long	get;
+};
+
+/*
+ *	ZFW_CTRL - This is the data structure that includes all other
+ *	data structures used by the Firmware.
+ */
+
+struct ZFW_CTRL {
+	struct BOARD_CTRL	board_ctrl;
+	struct CH_CTRL		ch_ctrl[MAX_CHAN];
+	struct BUF_CTRL		buf_ctrl[MAX_CHAN];
+};
+
+/****************** ****************** *******************/
+#endif
+
+#endif /* _UAPI_LINUX_CYCLADES_H */
Index: linux/include/uapi/linux/major.h
===================================================================
--- linux.orig/include/uapi/linux/major.h
+++ linux/include/uapi/linux/major.h
@@ -34,6 +34,8 @@
 #define GOLDSTAR_CDROM_MAJOR	16
 #define OPTICS_CDROM_MAJOR	17
 #define SANYO_CDROM_MAJOR	18
+#define CYCLADES_MAJOR		19	/* Obsolete */
+#define CYCLADESAUX_MAJOR	20	/* Obsolete */
 #define MITSUMI_X_CDROM_MAJOR	20
 #define MFM_ACORN_MAJOR		21	/* ARM Linux /dev/mfm */
 #define SCSI_GENERIC_MAJOR	21
