diff mbox series

[5.4,172/214] xhci: Do warm-reset when both CAS and XDEV_RESUME are set

Message ID 20200901151001.218679544@linuxfoundation.org
State Superseded
Headers show
Series None | expand

Commit Message

Greg KH Sept. 1, 2020, 3:10 p.m. UTC 
From: Kai-Heng Feng <kai.heng.feng@canonical.com>

commit 904df64a5f4d5ebd670801d869ca0a6d6a6e8df6 upstream.

Sometimes re-plugging a USB device during system sleep renders the device
useless:
[  173.418345] xhci_hcd 0000:00:14.0: Get port status 2-4 read: 0x14203e2, return 0x10262
...
[  176.496485] usb 2-4: Waited 2000ms for CONNECT
[  176.496781] usb usb2-port4: status 0000.0262 after resume, -19
[  176.497103] usb 2-4: can't resume, status -19
[  176.497438] usb usb2-port4: logical disconnect

Because PLS equals to XDEV_RESUME, xHCI driver reports U3 to usbcore,
despite of CAS bit is flagged.

So proritize CAS over XDEV_RESUME to let usbcore handle warm-reset for
the port.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200821091549.20556-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/host/xhci-hub.c |   19 ++++++++++---------
 1 file changed, 10 insertions(+), 9 deletions(-)
diff mbox series

Patch

--- a/drivers/usb/host/xhci-hub.c
+++ b/drivers/usb/host/xhci-hub.c
@@ -738,15 +738,6 @@  static void xhci_hub_report_usb3_link_st
 {
 	u32 pls = status_reg & PORT_PLS_MASK;
 
-	/* resume state is a xHCI internal state.
-	 * Do not report it to usb core, instead, pretend to be U3,
-	 * thus usb core knows it's not ready for transfer
-	 */
-	if (pls == XDEV_RESUME) {
-		*status |= USB_SS_PORT_LS_U3;
-		return;
-	}
-
 	/* When the CAS bit is set then warm reset
 	 * should be performed on port
 	 */
@@ -769,6 +760,16 @@  static void xhci_hub_report_usb3_link_st
 		pls |= USB_PORT_STAT_CONNECTION;
 	} else {
 		/*
+		 * Resume state is an xHCI internal state.  Do not report it to
+		 * usb core, instead, pretend to be U3, thus usb core knows
+		 * it's not ready for transfer.
+		 */
+		if (pls == XDEV_RESUME) {
+			*status |= USB_SS_PORT_LS_U3;
+			return;
+		}
+
+		/*
 		 * If CAS bit isn't set but the Port is already at
 		 * Compliance Mode, fake a connection so the USB core
 		 * notices the Compliance state and resets the port.