diff mbox series

[4.19,104/125] irqchip/stm32-exti: Avoid losing interrupts due to clearing pending bits by mistake

Message ID 20200901150939.704632067@linuxfoundation.org
State Superseded
Headers show
Series None | expand

Commit Message

Greg Kroah-Hartman Sept. 1, 2020, 3:10 p.m. UTC 
From: qiuguorui1 <qiuguorui1@huawei.com>

commit e579076ac0a3bebb440fab101aef3c42c9f4c709 upstream.

In the current code, when the eoi callback of the exti clears the pending
bit of the current interrupt, it will first read the values of fpr and
rpr, then logically OR the corresponding bit of the interrupt number,
and finally write back to fpr and rpr.

We found through experiments that if two exti interrupts,
we call them int1/int2, arrive almost at the same time. in our scenario,
the time difference is 30 microseconds, assuming int1 is triggered first.

there will be an extreme scenario: both int's pending bit are set to 1,
the irq handle of int1 is executed first, and eoi handle is then executed,
at this moment, all pending bits are cleared, but the int 2 has not
finally been reported to the cpu yet, which eventually lost int2.

According to stm32's TRM description about rpr and fpr: Writing a 1 to this
bit will trigger a rising edge event on event x, Writing 0 has no
effect.

Therefore, when clearing the pending bit, we only need to clear the
pending bit of the irq.

Fixes: 927abfc4461e7 ("irqchip/stm32: Add stm32mp1 support with hierarchy domain")
Signed-off-by: qiuguorui1 <qiuguorui1@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org # v4.18+
Link: https://lore.kernel.org/r/20200820031629.15582-1-qiuguorui1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/irqchip/irq-stm32-exti.c |   14 ++++++++++++--
 1 file changed, 12 insertions(+), 2 deletions(-)
diff mbox series

Patch

--- a/drivers/irqchip/irq-stm32-exti.c
+++ b/drivers/irqchip/irq-stm32-exti.c
@@ -382,6 +382,16 @@  static void stm32_irq_ack(struct irq_dat
 	irq_gc_unlock(gc);
 }
 
+/* directly set the target bit without reading first. */
+static inline void stm32_exti_write_bit(struct irq_data *d, u32 reg)
+{
+	struct stm32_exti_chip_data *chip_data = irq_data_get_irq_chip_data(d);
+	void __iomem *base = chip_data->host_data->base;
+	u32 val = BIT(d->hwirq % IRQS_PER_BANK);
+
+	writel_relaxed(val, base + reg);
+}
+
 static inline u32 stm32_exti_set_bit(struct irq_data *d, u32 reg)
 {
 	struct stm32_exti_chip_data *chip_data = irq_data_get_irq_chip_data(d);
@@ -415,9 +425,9 @@  static void stm32_exti_h_eoi(struct irq_
 
 	raw_spin_lock(&chip_data->rlock);
 
-	stm32_exti_set_bit(d, stm32_bank->rpr_ofst);
+	stm32_exti_write_bit(d, stm32_bank->rpr_ofst);
 	if (stm32_bank->fpr_ofst != UNDEF_REG)
-		stm32_exti_set_bit(d, stm32_bank->fpr_ofst);
+		stm32_exti_write_bit(d, stm32_bank->fpr_ofst);
 
 	raw_spin_unlock(&chip_data->rlock);