@@ -58,6 +58,7 @@ typedef struct IDEDMAOps IDEDMAOps;
#define TAG_MASK 0xf8
/* Bits of Device Control register */
+#define IDE_CTRL_HOB 0x80
#define IDE_CTRL_RESET 0x04
#define IDE_CTRL_DISABLE_IRQ 0x02
@@ -1215,8 +1215,7 @@ static void ide_cmd_lba48_transform(IDEState *s, int lba48)
static void ide_clear_hob(IDEBus *bus)
{
/* any write clears HOB high bit of device control register */
- bus->ifs[0].select &= ~(1 << 7);
- bus->ifs[1].select &= ~(1 << 7);
+ bus->cmd &= ~(IDE_CTRL_HOB);
}
/* IOport [W]rite [R]egisters */
@@ -1256,12 +1255,14 @@ void ide_ioport_write(void *opaque, uint32_t addr, uint32_t val)
return;
}
+ /* NOTE: Device0 and Device1 both receive incoming register writes.
+ * (They're on the same bus! They have to!) */
+
switch (reg_num) {
case 0:
break;
case ATA_IOPORT_WR_FEATURES:
ide_clear_hob(bus);
- /* NOTE: data is written to the two drives */
bus->ifs[0].hob_feature = bus->ifs[0].feature;
bus->ifs[1].hob_feature = bus->ifs[1].feature;
bus->ifs[0].feature = val;
@@ -1296,7 +1297,7 @@ void ide_ioport_write(void *opaque, uint32_t addr, uint32_t val)
bus->ifs[1].hcyl = val;
break;
case ATA_IOPORT_WR_DEVICE_HEAD:
- /* FIXME: HOB readback uses bit 7 */
+ ide_clear_hob(bus);
bus->ifs[0].select = val | 0xa0;
bus->ifs[1].select = val | 0xa0;
/* select drive */
@@ -1304,7 +1305,7 @@ void ide_ioport_write(void *opaque, uint32_t addr, uint32_t val)
break;
default:
case ATA_IOPORT_WR_COMMAND:
- /* command */
+ ide_clear_hob(bus);
ide_exec_cmd(bus, val);
break;
}
@@ -2142,9 +2143,7 @@ uint32_t ide_ioport_read(void *opaque, uint32_t addr)
int ret, hob;
reg_num = addr & 7;
- /* FIXME: HOB readback uses bit 7, but it's always set right now */
- //hob = s->select & (1 << 7);
- hob = 0;
+ hob = bus->cmd & (IDE_CTRL_HOB);
switch (reg_num) {
case ATA_IOPORT_RR_DATA:
ret = 0xff;
I have been staring at this FIXME for years and I never knew what it meant. I finally stumbled across it! When writing to the command registers, the old value is shifted into a HOB copy of the register and the new value is written into the primary register. When reading registers, the value retrieved is dependent on the HOB bit in the CONTROL register. By setting bit 7 (0x80) in CONTROL, any register read will, if it has one, yield the HOB value for that register instead. Our code has a problem: We were using bit 7 of the DEVICE register to model this. We use bus->cmd roughly as the control register already, as it stores the value from ide_ctrl_write. Lastly, all command register writes reset the HOB, so fix that, too. Signed-off-by: John Snow <jsnow@redhat.com> --- include/hw/ide/internal.h | 1 + hw/ide/core.c | 15 +++++++-------- 2 files changed, 8 insertions(+), 8 deletions(-)