@@ -43,6 +43,7 @@ Contents:
intel/ipw2200
microsoft/netvsc
neterion/s2io
+ neterion/vxge
.. only:: subproject and html
similarity index 80%
rename from Documentation/networking/device_drivers/neterion/vxge.txt
rename to Documentation/networking/device_drivers/neterion/vxge.rst
@@ -1,24 +1,30 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+==============================================================================
Neterion's (Formerly S2io) X3100 Series 10GbE PCIe Server Adapter Linux driver
==============================================================================
-Contents
---------
+.. Contents
-1) Introduction
-2) Features supported
-3) Configurable driver parameters
-4) Troubleshooting
+ 1) Introduction
+ 2) Features supported
+ 3) Configurable driver parameters
+ 4) Troubleshooting
+
+1. Introduction
+===============
-1) Introduction:
-----------------
This Linux driver supports all Neterion's X3100 series 10 GbE PCIe I/O
Virtualized Server adapters.
+
The X3100 series supports four modes of operation, configurable via
-firmware -
- Single function mode
- Multi function mode
- SRIOV mode
- MRIOV mode
+firmware:
+
+ - Single function mode
+ - Multi function mode
+ - SRIOV mode
+ - MRIOV mode
+
The functions share a 10GbE link and the pci-e bus, but hardly anything else
inside the ASIC. Features like independent hw reset, statistics, bandwidth/
priority allocation and guarantees, GRO, TSO, interrupt moderation etc are
@@ -26,41 +32,49 @@ supported independently on each function.
(See below for a complete list of features supported for both IPv4 and IPv6)
-2) Features supported:
-----------------------
+2. Features supported
+=====================
i) Single function mode (up to 17 queues)
ii) Multi function mode (up to 17 functions)
iii) PCI-SIG's I/O Virtualization
+
- Single Root mode: v1.0 (up to 17 functions)
- Multi-Root mode: v1.0 (up to 17 functions)
iv) Jumbo frames
+
X3100 Series supports MTU up to 9600 bytes, modifiable using
ip command.
v) Offloads supported: (Enabled by default)
- Checksum offload (TCP/UDP/IP) on transmit and receive paths
- TCP Segmentation Offload (TSO) on transmit path
- Generic Receive Offload (GRO) on receive path
+
+ - Checksum offload (TCP/UDP/IP) on transmit and receive paths
+ - TCP Segmentation Offload (TSO) on transmit path
+ - Generic Receive Offload (GRO) on receive path
vi) MSI-X: (Enabled by default)
+
Resulting in noticeable performance improvement (up to 7% on certain
platforms).
vii) NAPI: (Enabled by default)
+
For better Rx interrupt moderation.
viii)RTH (Receive Traffic Hash): (Enabled by default)
+
Receive side steering for better scaling.
ix) Statistics
+
Comprehensive MAC-level and software statistics displayed using
"ethtool -S" option.
x) Multiple hardware queues: (Enabled by default)
+
Up to 17 hardware based transmit and receive data channels, with
multiple steering options (transmit multiqueue enabled by default).
@@ -69,25 +83,33 @@ x) Multiple hardware queues: (Enabled by default)
i) max_config_dev
Specifies maximum device functions to be enabled.
+
Valid range: 1-8
ii) max_config_port
Specifies number of ports to be enabled.
+
Valid range: 1,2
+
Default: 1
-iii)max_config_vpath
+iii) max_config_vpath
Specifies maximum VPATH(s) configured for each device function.
+
Valid range: 1-17
iv) vlan_tag_strip
Enables/disables vlan tag stripping from all received tagged frames that
are not replicated at the internal L2 switch.
+
Valid range: 0,1 (disabled, enabled respectively)
+
Default: 1
v) addr_learn_en
Enable learning the mac address of the guest OS interface in
virtualization environment.
+
Valid range: 0,1 (disabled, enabled respectively)
+
Default: 0
@@ -11692,7 +11692,7 @@ M: Jon Mason <jdmason@kudzu.us>
L: netdev@vger.kernel.org
S: Supported
F: Documentation/networking/device_drivers/neterion/s2io.rst
-F: Documentation/networking/device_drivers/neterion/vxge.txt
+F: Documentation/networking/device_drivers/neterion/vxge.rst
F: drivers/net/ethernet/neterion/
NETFILTER
@@ -42,7 +42,7 @@ config VXGE
labeled as either one, depending on its age.
More specific information on configuring the driver is in
- <file:Documentation/networking/device_drivers/neterion/vxge.txt>.
+ <file:Documentation/networking/device_drivers/neterion/vxge.rst>.
To compile this driver as a module, choose M here. The module
will be called vxge.
- add SPDX header; - adjust titles and chapters, adding proper markups; - comment out text-only TOC from html/pdf output; - mark code blocks and literals as such; - adjust identation, whitespaces and blank lines where needed; - add to networking/index.rst. Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> --- .../networking/device_drivers/index.rst | 1 + .../neterion/{vxge.txt => vxge.rst} | 60 +++++++++++++------ MAINTAINERS | 2 +- drivers/net/ethernet/neterion/Kconfig | 2 +- 4 files changed, 44 insertions(+), 21 deletions(-) rename Documentation/networking/device_drivers/neterion/{vxge.txt => vxge.rst} (80%)