@@ -767,8 +767,12 @@ static int
qca8k_setup(struct dsa_switch *ds)
{
struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv;
+ const struct qca8k_match_data *data;
+ u32 ret_val, mask;
int ret, i;
- u32 ret_val;
+
+ /* get the switches ID from the compatible */
+ data = of_device_get_match_data(priv->dev);
/* Make sure that port 0 is the cpu port */
if (!dsa_is_cpu_port(ds, 0)) {
@@ -875,6 +879,45 @@ qca8k_setup(struct dsa_switch *ds)
}
}
+ if (data->id == QCA8K_ID_QCA8337) {
+ for (i = 0; i < QCA8K_NUM_PORTS; i++) {
+ switch (i) {
+ /* The 2 CPU port and port 5 requires some different
+ * priority than any other ports.
+ */
+ case 0:
+ case 5:
+ case 6:
+ mask = QCA8K_PORT_HOL_CTRL0_EG_PRI0(0x3) |
+ QCA8K_PORT_HOL_CTRL0_EG_PRI1(0x4) |
+ QCA8K_PORT_HOL_CTRL0_EG_PRI2(0x4) |
+ QCA8K_PORT_HOL_CTRL0_EG_PRI3(0x4) |
+ QCA8K_PORT_HOL_CTRL0_EG_PRI4(0x6) |
+ QCA8K_PORT_HOL_CTRL0_EG_PRI5(0x8) |
+ QCA8K_PORT_HOL_CTRL0_EG_PORT(0x1e);
+ break;
+ default:
+ mask = QCA8K_PORT_HOL_CTRL0_EG_PRI0(0x3) |
+ QCA8K_PORT_HOL_CTRL0_EG_PRI1(0x4) |
+ QCA8K_PORT_HOL_CTRL0_EG_PRI2(0x6) |
+ QCA8K_PORT_HOL_CTRL0_EG_PRI3(0x8) |
+ QCA8K_PORT_HOL_CTRL0_EG_PORT(0x19);
+ }
+ qca8k_write(priv, QCA8K_REG_PORT_HOL_CTRL0(i), mask);
+
+ mask = QCA8K_PORT_HOL_CTRL1_ING(0x6) |
+ QCA8K_PORT_HOL_CTRL1_EG_PRI_BUF_EN |
+ QCA8K_PORT_HOL_CTRL1_EG_PORT_BUF_EN |
+ QCA8K_PORT_HOL_CTRL1_WRED_EN;
+ qca8k_rmw(priv, QCA8K_REG_PORT_HOL_CTRL1(i),
+ QCA8K_PORT_HOL_CTRL1_ING_BUF |
+ QCA8K_PORT_HOL_CTRL1_EG_PRI_BUF_EN |
+ QCA8K_PORT_HOL_CTRL1_EG_PORT_BUF_EN |
+ QCA8K_PORT_HOL_CTRL1_WRED_EN,
+ mask, &ret_val);
+ }
+ }
+
/* Setup our port MTUs to match power on defaults */
for (i = 0; i < QCA8K_NUM_PORTS; i++)
priv->port_mtu[i] = ETH_FRAME_LEN + ETH_FCS_LEN;
@@ -895,9 +938,13 @@ static void
qca8k_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
const struct phylink_link_state *state)
{
+ const struct qca8k_match_data *data;
struct qca8k_priv *priv = ds->priv;
u32 reg, val;
+ /* get the switches ID from the compatible */
+ data = of_device_get_match_data(priv->dev);
+
switch (port) {
case 0: /* 1st CPU port */
if (state->interface != PHY_INTERFACE_MODE_RGMII &&
@@ -948,8 +995,10 @@ qca8k_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
QCA8K_PORT_PAD_RGMII_EN |
QCA8K_PORT_PAD_RGMII_TX_DELAY(QCA8K_MAX_DELAY) |
QCA8K_PORT_PAD_RGMII_RX_DELAY(QCA8K_MAX_DELAY));
- qca8k_write(priv, QCA8K_REG_PORT5_PAD_CTRL,
- QCA8K_PORT_PAD_RGMII_RX_DELAY_EN);
+ /* QCA8337 requires to set rgmii rx delay */
+ if (data->id == QCA8K_ID_QCA8337)
+ qca8k_write(priv, QCA8K_REG_PORT5_PAD_CTRL,
+ QCA8K_PORT_PAD_RGMII_RX_DELAY_EN);
break;
case PHY_INTERFACE_MODE_SGMII:
case PHY_INTERFACE_MODE_1000BASEX:
@@ -166,6 +166,30 @@
#define QCA8K_PORT_LOOKUP_STATE GENMASK(18, 16)
#define QCA8K_PORT_LOOKUP_LEARN BIT(20)
+#define QCA8K_REG_PORT_HOL_CTRL0(_i) (0x970 + (_i) * 0x8)
+#define QCA8K_PORT_HOL_CTRL0_EG_PRI0_BUF GENMASK(3, 0)
+#define QCA8K_PORT_HOL_CTRL0_EG_PRI0(x) ((x) << 0)
+#define QCA8K_PORT_HOL_CTRL0_EG_PRI1_BUF GENMASK(7, 4)
+#define QCA8K_PORT_HOL_CTRL0_EG_PRI1(x) ((x) << 4)
+#define QCA8K_PORT_HOL_CTRL0_EG_PRI2_BUF GENMASK(11, 8)
+#define QCA8K_PORT_HOL_CTRL0_EG_PRI2(x) ((x) << 8)
+#define QCA8K_PORT_HOL_CTRL0_EG_PRI3_BUF GENMASK(15, 12)
+#define QCA8K_PORT_HOL_CTRL0_EG_PRI3(x) ((x) << 12)
+#define QCA8K_PORT_HOL_CTRL0_EG_PRI4_BUF GENMASK(19, 16)
+#define QCA8K_PORT_HOL_CTRL0_EG_PRI4(x) ((x) << 16)
+#define QCA8K_PORT_HOL_CTRL0_EG_PRI5_BUF GENMASK(23, 20)
+#define QCA8K_PORT_HOL_CTRL0_EG_PRI5(x) ((x) << 20)
+#define QCA8K_PORT_HOL_CTRL0_EG_PORT_BUF GENMASK(29, 24)
+#define QCA8K_PORT_HOL_CTRL0_EG_PORT(x) ((x) << 24)
+
+#define QCA8K_REG_PORT_HOL_CTRL1(_i) (0x974 + (_i) * 0x8)
+#define QCA8K_PORT_HOL_CTRL1_ING_BUF GENMASK(3, 0)
+#define QCA8K_PORT_HOL_CTRL1_ING(x) ((x) << 0)
+#define QCA8K_PORT_HOL_CTRL1_EG_PRI_BUF_EN BIT(6)
+#define QCA8K_PORT_HOL_CTRL1_EG_PORT_BUF_EN BIT(7)
+#define QCA8K_PORT_HOL_CTRL1_WRED_EN BIT(8)
+#define QCA8K_PORT_HOL_CTRL1_EG_MIRROR_EN BIT(16)
+
/* Pkt edit registers */
#define QCA8K_EGRESS_VLAN(x) (0x0c70 + (4 * (x / 2)))
The port 5 of the ar8337 have some problem in flood condition. The original legacy driver had some specific buffer and priority settings for the different port suggested by the QCA switch team. Add this missing settings to improve switch stability under load condition. The packet priority tweak and the rx delay is specific to qca8337. Limit this changes to qca8337 as now we also support 8327 switch. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> --- drivers/net/dsa/qca8k.c | 55 ++++++++++++++++++++++++++++++++++++++--- drivers/net/dsa/qca8k.h | 24 ++++++++++++++++++ 2 files changed, 76 insertions(+), 3 deletions(-)