@@ -12,6 +12,8 @@
#include <linux/slab.h>
#include <linux/module.h>
#include <linux/acpi.h>
+#include <linux/firmware.h>
+#include <asm/unaligned.h>
#include "xhci.h"
#include "xhci-trace.h"
@@ -279,6 +281,458 @@ static void xhci_pme_acpi_rtd3_enable(struct pci_dev *dev)
static void xhci_pme_acpi_rtd3_enable(struct pci_dev *dev) { }
#endif /* CONFIG_ACPI */
+static const struct renesas_fw_entry {
+ const char *firmware_name;
+ u16 device;
+ u8 revision;
+ u16 expected_version;
+} renesas_fw_table[] = {
+ /*
+ * Only the uPD720201K8-711-BAC-A or uPD720202K8-711-BAA-A
+ * are listed in R19UH0078EJ0500 Rev.5.00 as devices which
+ * need the software loader.
+ *
+ * PP2U/ReleaseNote_USB3-201-202-FW.txt:
+ *
+ * Note: This firmware is for the following devices.
+ * - uPD720201 ES 2.0 sample whose revision ID is 2.
+ * - uPD720201 ES 2.1 sample & CS sample & Mass product, ID is 3.
+ * - uPD720202 ES 2.0 sample & CS sample & Mass product, ID is 2.
+ */
+ { "K2013080.mem", 0x0014, 0x02, 0x2013 },
+ { "K2013080.mem", 0x0014, 0x03, 0x2013 },
+ { "K2013080.mem", 0x0015, 0x02, 0x2013 },
+};
+
+static const struct renesas_fw_entry *renesas_needs_fw_dl(struct pci_dev *dev)
+{
+ const struct renesas_fw_entry *entry;
+ size_t i;
+
+ /* This loader will only work with a RENESAS device. */
+ if (!(dev->vendor == PCI_VENDOR_ID_RENESAS))
+ return NULL;
+
+ for (i = 0; i < ARRAY_SIZE(renesas_fw_table); i++) {
+ entry = &renesas_fw_table[i];
+ if (entry->device == dev->device &&
+ entry->revision == dev->revision)
+ return entry;
+ }
+
+ return NULL;
+}
+
+static int renesas_fw_download_image(struct pci_dev *dev,
+ const u32 *fw,
+ size_t step)
+{
+ size_t i;
+ int err;
+ u8 fw_status;
+ bool data0_or_data1;
+
+ /*
+ * The hardware does alternate between two 32-bit pages.
+ * (This is because each row of the firmware is 8 bytes).
+ *
+ * for even steps we use DATA0, for odd steps DATA1.
+ */
+ data0_or_data1 = (step & 1) == 1;
+
+ /* step+1. Read "Set DATAX" and confirm it is cleared. */
+ for (i = 0; i < 10000; i++) {
+ err = pci_read_config_byte(dev, 0xF5, &fw_status);
+ if (err)
+ return pcibios_err_to_errno(err);
+ if (!(fw_status & BIT(data0_or_data1)))
+ break;
+
+ udelay(1);
+ }
+ if (i == 10000)
+ return -ETIMEDOUT;
+
+ /*
+ * step+2. Write FW data to "DATAX".
+ * "LSB is left" => force little endian
+ */
+ err = pci_write_config_dword(dev, data0_or_data1 ? 0xFC : 0xF8,
+ (__force u32) cpu_to_le32(fw[step]));
+ if (err)
+ return pcibios_err_to_errno(err);
+
+ udelay(100);
+
+ /* step+3. Set "Set DATAX". */
+ err = pci_write_config_byte(dev, 0xF5, BIT(data0_or_data1));
+ if (err)
+ return pcibios_err_to_errno(err);
+
+ return 0;
+}
+
+static int renesas_fw_verify(struct pci_dev *dev,
+ const void *fw_data,
+ size_t length)
+{
+ const struct renesas_fw_entry *entry = renesas_needs_fw_dl(dev);
+ u16 fw_version_pointer;
+ u16 fw_version;
+
+ if (!entry)
+ return -EINVAL;
+
+ /*
+ * The Firmware's Data Format is describe in
+ * "6.3 Data Format" R19UH0078EJ0500 Rev.5.00 page 124
+ */
+
+ /* "Each row is 8 bytes". => firmware size must be a multiple of 8. */
+ if (length % 8 != 0) {
+ dev_err(&dev->dev, "firmware size is not a multipe of 8.");
+ return -EINVAL;
+ }
+
+ /*
+ * The bootrom chips of the big brother have sizes up to 64k, let's
+ * assume that's the biggest the firmware can get.
+ */
+ if (length < 0x1000 || length >= 0x10000) {
+ dev_err(&dev->dev, "firmware is size %zd is not (4k - 64k).",
+ length);
+ return -EINVAL;
+ }
+
+ /* The First 2 bytes are fixed value (55aa). "LSB on Left" */
+ if (get_unaligned_le16(fw_data) != 0x55aa) {
+ dev_err(&dev->dev, "no valid firmware header found.");
+ return -EINVAL;
+ }
+
+ /* verify the firmware version position and print it. */
+ fw_version_pointer = get_unaligned_le16(fw_data + 4);
+ if (fw_version_pointer + 2 >= length) {
+ dev_err(&dev->dev, "firmware version pointer is outside of the firmware image.");
+ return -EINVAL;
+ }
+
+ fw_version = get_unaligned_le16(fw_data + fw_version_pointer);
+ dev_dbg(&dev->dev, "got firmware version: %02x.", fw_version);
+
+ if (fw_version != entry->expected_version) {
+ dev_err(&dev->dev, "firmware version mismatch, expected version: %02x.",
+ entry->expected_version);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int renesas_fw_check_running(struct pci_dev *pdev)
+{
+ int err;
+ u8 fw_state;
+
+ /*
+ * Test if the device is actually needing the firmware. As most
+ * BIOSes will initialize the device for us. If the device is
+ * initialized.
+ */
+ err = pci_read_config_byte(pdev, 0xF4, &fw_state);
+ if (err)
+ return pcibios_err_to_errno(err);
+
+ /*
+ * Check if "FW Download Lock" is locked. If it is and the FW is
+ * ready we can simply continue. If the FW is not ready, we have
+ * to give up.
+ */
+ if (fw_state & BIT(1)) {
+ dev_dbg(&pdev->dev, "FW Download Lock is engaged.");
+
+ if (fw_state & BIT(4))
+ return 0;
+
+ dev_err(&pdev->dev, "FW Download Lock is set and FW is not ready. Giving Up.");
+ return -EIO;
+ }
+
+ /*
+ * Check if "FW Download Enable" is set. If someone (us?) tampered
+ * with it and it can't be resetted, we have to give up too... and
+ * ask for a forgiveness and a reboot.
+ */
+ if (fw_state & BIT(0)) {
+ dev_err(&pdev->dev, "FW Download Enable is stale. Giving Up (poweroff/reboot needed).");
+ return -EIO;
+ }
+
+ /* Otherwise, Check the "Result Code" Bits (6:4) and act accordingly */
+ switch ((fw_state & 0x70)) {
+ case 0: /* No result yet */
+ dev_dbg(&pdev->dev, "FW is not ready/loaded yet.");
+
+ /* tell the caller, that this device needs the firmware. */
+ return 1;
+
+ case BIT(4): /* Success, device should be working. */
+ dev_dbg(&pdev->dev, "FW is ready.");
+ return 0;
+
+ case BIT(5): /* Error State */
+ dev_err(&pdev->dev, "hardware is in an error state. Giving up (poweroff/reboot needed).");
+ return -ENODEV;
+
+ default: /* All other states are marked as "Reserved states" */
+ dev_err(&pdev->dev, "hardware is in an invalid state %x. Giving up (poweroff/reboot needed).",
+ (fw_state & 0x70) >> 4);
+ return -EINVAL;
+ }
+}
+
+static int renesas_hw_check_run_stop_busy(struct pci_dev *pdev)
+{
+#if 0
+ u32 val;
+
+ /*
+ * 7.1.3 Note 3: "... must not set 'FW Download Enable' when
+ * 'RUN/STOP' of USBCMD Register is set"
+ */
+ val = readl(hcd->regs + 0x20);
+ if (val & BIT(0)) {
+ dev_err(&pdev->dev, "hardware is busy and can't receive a FW.");
+ return -EBUSY;
+ }
+#endif
+ return 0;
+}
+
+static int renesas_fw_download(struct pci_dev *pdev,
+ const struct firmware *fw, unsigned int retry_counter)
+{
+ const u32 *fw_data = (const u32 *) fw->data;
+ size_t i;
+ int err;
+ u8 fw_status;
+
+ /*
+ * For more information and the big picture: please look at the
+ * "Firmware Download Sequence" in "7.1 FW Download Interface"
+ * of R19UH0078EJ0500 Rev.5.00 page 131
+ */
+ err = renesas_hw_check_run_stop_busy(pdev);
+ if (err)
+ return err;
+
+ /*
+ * 0. Set "FW Download Enable" bit in the
+ * "FW Download Control & Status Register" at 0xF4
+ */
+ err = pci_write_config_byte(pdev, 0xF4, BIT(0));
+ if (err)
+ return pcibios_err_to_errno(err);
+
+ /* 1 - 10 follow one step after the other. */
+ for (i = 0; i < fw->size / 4; i++) {
+ err = renesas_fw_download_image(pdev, fw_data, i);
+ if (err) {
+ dev_err(&pdev->dev, "Firmware Download Step %zd failed at position %zd bytes with (%d).",
+ i, i * 4, err);
+ return err;
+ }
+ }
+
+ /*
+ * This sequence continues until the last data is written to
+ * "DATA0" or "DATA1". Naturally, we wait until "SET DATA0/1"
+ * is cleared by the hardware beforehand.
+ */
+ for (i = 0; i < 10000; i++) {
+ err = pci_read_config_byte(pdev, 0xF5, &fw_status);
+ if (err)
+ return pcibios_err_to_errno(err);
+ if (!(fw_status & (BIT(0) | BIT(1))))
+ break;
+
+ udelay(1);
+ }
+ if (i == 10000)
+ dev_warn(&pdev->dev, "Final Firmware Download step timed out.");
+
+ /*
+ * 11. After finishing writing the last data of FW, the
+ * System Software must clear "FW Download Enable"
+ */
+ err = pci_write_config_byte(pdev, 0xF4, 0);
+ if (err)
+ return pcibios_err_to_errno(err);
+
+ /* 12. Read "Result Code" and confirm it is good. */
+ for (i = 0; i < 10000; i++) {
+ err = pci_read_config_byte(pdev, 0xF4, &fw_status);
+ if (err)
+ return pcibios_err_to_errno(err);
+ if (fw_status & BIT(4))
+ break;
+
+ udelay(1);
+ }
+ if (i == 10000) {
+ /* Timed out / Error - let's see if we can fix this */
+ err = renesas_fw_check_running(pdev);
+ switch (err) {
+ case 0: /*
+ * we shouldn't end up here.
+ * maybe it took a little bit longer.
+ * But all should be well?
+ */
+ break;
+
+ case 1: /* (No result yet? - we can try to retry) */
+ if (retry_counter < 10) {
+ retry_counter++;
+ dev_warn(&pdev->dev, "Retry Firmware download: %d try.",
+ retry_counter);
+ return renesas_fw_download(pdev, fw,
+ retry_counter);
+ }
+ return -ETIMEDOUT;
+
+ default:
+ return err;
+ }
+ }
+ /*
+ * Optional last step: Engage Firmware Lock
+ *
+ * err = pci_write_config_byte(pdev, 0xF4, BIT(2));
+ * if (err)
+ * return pcibios_err_to_errno(err);
+ */
+
+ return 0;
+}
+
+struct renesas_fw_ctx {
+ struct pci_dev *pdev;
+ const struct pci_device_id *id;
+ bool resume;
+};
+
+static int xhci_pci_probe(struct pci_dev *pdev,
+ const struct pci_device_id *id);
+
+static void renesas_fw_callback(const struct firmware *fw,
+ void *context)
+{
+ struct renesas_fw_ctx *ctx = context;
+ struct pci_dev *pdev = ctx->pdev;
+ struct device *parent = pdev->dev.parent;
+ int err = -ENOENT;
+
+ if (fw) {
+ err = renesas_fw_verify(pdev, fw->data, fw->size);
+ if (!err) {
+ err = renesas_fw_download(pdev, fw, 0);
+ release_firmware(fw);
+ if (!err) {
+ if (ctx->resume)
+ return;
+
+ err = xhci_pci_probe(pdev, ctx->id);
+ if (!err) {
+ /* everything worked */
+ devm_kfree(&pdev->dev, ctx);
+ return;
+ }
+
+ /* in case of an error - fall through */
+ } else {
+ dev_err(&pdev->dev, "firmware failed to download (%d).",
+ err);
+ }
+ }
+ } else {
+ dev_err(&pdev->dev, "firmware failed to load (%d).", err);
+ }
+
+ dev_info(&pdev->dev, "Unloading driver");
+
+ if (parent)
+ device_lock(parent);
+
+ device_release_driver(&pdev->dev);
+
+ if (parent)
+ device_unlock(parent);
+
+ pci_dev_put(pdev);
+}
+
+static int renesas_fw_alive_check(struct pci_dev *pdev)
+{
+ const struct renesas_fw_entry *entry;
+ int err;
+
+ /* check if we have a eligible RENESAS' uPD720201/2 w/o FW. */
+ entry = renesas_needs_fw_dl(pdev);
+ if (!entry)
+ return 0;
+
+ err = renesas_fw_check_running(pdev);
+ /* Also go ahead, if the firmware is running */
+ if (err == 0)
+ return 0;
+
+ /* At this point, we can be sure that the FW isn't ready. */
+ return err;
+}
+
+static int renesas_fw_download_to_hw(struct pci_dev *pdev,
+ const struct pci_device_id *id,
+ bool do_resume)
+{
+ const struct renesas_fw_entry *entry;
+ struct renesas_fw_ctx *ctx;
+ int err;
+
+ /* check if we have a eligible RENESAS' uPD720201/2 w/o FW. */
+ entry = renesas_needs_fw_dl(pdev);
+ if (!entry)
+ return 0;
+
+ err = renesas_fw_check_running(pdev);
+ /* Continue ahead, if the firmware is already running. */
+ if (err == 0)
+ return 0;
+
+ if (err != 1)
+ return err;
+
+ ctx = devm_kzalloc(&pdev->dev, sizeof(*ctx), GFP_KERNEL);
+ if (!ctx)
+ return -ENOMEM;
+ ctx->pdev = pdev;
+ ctx->resume = do_resume;
+ ctx->id = id;
+
+ pci_dev_get(pdev);
+ err = request_firmware_nowait(THIS_MODULE, 1, entry->firmware_name,
+ &pdev->dev, GFP_KERNEL, ctx, renesas_fw_callback);
+ if (err) {
+ pci_dev_put(pdev);
+ return err;
+ }
+
+ /*
+ * The renesas_fw_callback() callback will continue the probe
+ * process, once it aquires the firmware.
+ */
+ return 1;
+}
+
/* called during probe() after chip reset completes */
static int xhci_pci_setup(struct usb_hcd *hcd)
{
@@ -317,6 +771,22 @@ static int xhci_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
struct hc_driver *driver;
struct usb_hcd *hcd;
+ /*
+ * Check if this device is a RENESAS uPD720201/2 device.
+ * Otherwise, we can continue with xhci_pci_probe as usual.
+ */
+ retval = renesas_fw_download_to_hw(dev, id, false);
+ switch (retval) {
+ case 0:
+ break;
+
+ case 1: /* let it load the firmware and recontinue the probe. */
+ return 0;
+
+ default:
+ return retval;
+ };
+
driver = (struct hc_driver *)id->driver_data;
/* Prevent runtime suspending between USB-2 and USB-3 initialization */
@@ -381,6 +851,16 @@ static void xhci_pci_remove(struct pci_dev *dev)
{
struct xhci_hcd *xhci;
+ if (renesas_fw_alive_check(dev)) {
+ /*
+ * bail out early, if this was a renesas device w/o FW.
+ * Else we might hit the NMI watchdog in xhci_handsake
+ * during xhci_reset as part of the driver's unloading.
+ * which we forced in the renesas_fw_callback().
+ */
+ return;
+ }
+
xhci = hcd_to_xhci(pci_get_drvdata(dev));
xhci->xhc_state |= XHCI_STATE_REMOVING;