@@ -1815,9 +1815,9 @@
options(such as CONFIG_IOMMU_DEFAULT_PASSTHROUGH) to
choose which mode to be used.
Note: For historical reasons, ARM64/S390/PPC/X86 have
- their specific options. Currently, only ARM64 support
- this boot option, and hope other ARCHs to use this as
- generic boot option.
+ their specific options. Currently, only ARM64/S390
+ support this boot option, and hope other ARCHs to use
+ this as generic boot option.
passthrough
Configure DMA to bypass the IOMMU by default.
lazy
@@ -9,6 +9,7 @@
#include <linux/kernel.h>
#include <linux/slab.h>
#include <linux/export.h>
+#include <linux/iommu.h>
#include <linux/iommu-helper.h>
#include <linux/dma-mapping.h>
#include <linux/vmalloc.h>
@@ -17,7 +18,6 @@
static struct kmem_cache *dma_region_table_cache;
static struct kmem_cache *dma_page_table_cache;
-static int s390_iommu_strict;
static int zpci_refresh_global(struct zpci_dev *zdev)
{
@@ -193,13 +193,13 @@ static int __dma_purge_tlb(struct zpci_dev *zdev, dma_addr_t dma_addr,
if (!zdev->tlb_refresh)
return 0;
} else {
- if (!s390_iommu_strict)
+ if (!IOMMU_DMA_MODE_IS_STRICT())
return 0;
}
ret = zpci_refresh_trans((u64) zdev->fh << 32, dma_addr,
PAGE_ALIGN(size));
- if (ret == -ENOMEM && !s390_iommu_strict) {
+ if (ret == -ENOMEM && !IOMMU_DMA_MODE_IS_STRICT()) {
/* enable the hypervisor to free some resources */
if (zpci_refresh_global(zdev))
goto out;
@@ -278,7 +278,7 @@ static dma_addr_t dma_alloc_address(struct device *dev, int size)
spin_lock_irqsave(&zdev->iommu_bitmap_lock, flags);
offset = __dma_alloc_iommu(dev, zdev->next_bit, size);
if (offset == -1) {
- if (!s390_iommu_strict) {
+ if (!IOMMU_DMA_MODE_IS_STRICT()) {
/* global flush before DMA addresses are reused */
if (zpci_refresh_global(zdev))
goto out_error;
@@ -313,7 +313,7 @@ static void dma_free_address(struct device *dev, dma_addr_t dma_addr, int size)
if (!zdev->iommu_bitmap)
goto out;
- if (s390_iommu_strict)
+ if (IOMMU_DMA_MODE_IS_STRICT())
bitmap_clear(zdev->iommu_bitmap, offset, size);
else
bitmap_set(zdev->lazy_bitmap, offset, size);
@@ -584,7 +584,7 @@ int zpci_dma_init_device(struct zpci_dev *zdev)
rc = -ENOMEM;
goto free_dma_table;
}
- if (!s390_iommu_strict) {
+ if (!IOMMU_DMA_MODE_IS_STRICT()) {
zdev->lazy_bitmap = vzalloc(zdev->iommu_pages / 8);
if (!zdev->lazy_bitmap) {
rc = -ENOMEM;
@@ -675,7 +675,7 @@ void zpci_dma_exit(void)
static int __init s390_iommu_setup(char *str)
{
if (!strncmp(str, "strict", 6))
- s390_iommu_strict = 1;
+ iommu_default_dma_mode_set(IOMMU_DMA_MODE_STRICT);
return 0;
}
@@ -77,6 +77,7 @@ config IOMMU_DEBUGFS
choice
prompt "IOMMU dma mode"
depends on IOMMU_API
+ default IOMMU_DEFAULT_LAZY if S390_IOMMU
default IOMMU_DEFAULT_STRICT
help
This option allows IOMMU dma mode to be chose at build time, to
s390_iommu=strict is equivalent to iommu.dma_mode=strict. Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> --- Documentation/admin-guide/kernel-parameters.txt | 6 +++--- arch/s390/pci/pci_dma.c | 14 +++++++------- drivers/iommu/Kconfig | 1 + 3 files changed, 11 insertions(+), 10 deletions(-) -- 1.8.3