diff mbox series

[2/4] phy: ti-pipe3: improve DPLL stability for SATA & USB

Message ID 20190322085807.30216-3-rogerq@ti.com
State Accepted
Commit fdef2f9f700fab55c36d45e7c46607e935886c6c
Headers show
Series phy: ti-pipe3: Match TRM sequence & settings | expand

Commit Message

Roger Quadros March 22, 2019, 8:58 a.m. UTC
For increased DPLL stability use the settings recommended in
the TRM [1] for PHY_RX registers for SATA and USB.

For SATA we need to use spread spectrum settings even
though we don't have spread spectrum enabled. The
suggested non-spread spectrum settings don't work.

[1] DRA75x, DRA74x TRM - http://www.ti.com/lit/ug/sprui30f/sprui30f.pdf

Signed-off-by: Roger Quadros <rogerq@ti.com>

---
 drivers/phy/ti/phy-ti-pipe3.c | 215 +++++++++++++++++++++++++++-------
 1 file changed, 173 insertions(+), 42 deletions(-)

-- 
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
diff mbox series

Patch

diff --git a/drivers/phy/ti/phy-ti-pipe3.c b/drivers/phy/ti/phy-ti-pipe3.c
index 0913dd55d82a..cdc994f153b2 100644
--- a/drivers/phy/ti/phy-ti-pipe3.c
+++ b/drivers/phy/ti/phy-ti-pipe3.c
@@ -68,39 +68,61 @@ 
 #define PCIE_PCS_MASK			0xFF0000
 #define PCIE_PCS_DELAY_COUNT_SHIFT	0x10
 
-#define PCIEPHYRX_ANA_PROGRAMMABILITY	0x0000000C
+#define PIPE3_PHY_RX_ANA_PROGRAMMABILITY	0x0000000C
 #define INTERFACE_MASK			GENMASK(31, 27)
 #define INTERFACE_SHIFT			27
+#define INTERFACE_MODE_USBSS		BIT(4)
+#define INTERFACE_MODE_SATA_1P5		BIT(3)
+#define INTERFACE_MODE_SATA_3P0		BIT(2)
+#define INTERFACE_MODE_PCIE		BIT(0)
+
 #define LOSD_MASK			GENMASK(17, 14)
 #define LOSD_SHIFT			14
 #define MEM_PLLDIV			GENMASK(6, 5)
 
-#define PCIEPHYRX_TRIM			0x0000001C
-#define MEM_DLL_TRIM_SEL		GENMASK(31, 30)
+#define PIPE3_PHY_RX_TRIM		0x0000001C
+#define MEM_DLL_TRIM_SEL_MASK		GENMASK(31, 30)
 #define MEM_DLL_TRIM_SHIFT		30
 
-#define PCIEPHYRX_DLL			0x00000024
-#define MEM_DLL_PHINT_RATE		GENMASK(31, 30)
+#define PIPE3_PHY_RX_DLL		0x00000024
+#define MEM_DLL_PHINT_RATE_MASK		GENMASK(31, 30)
+#define MEM_DLL_PHINT_RATE_SHIFT	30
 
-#define PCIEPHYRX_DIGITAL_MODES		0x00000028
+#define PIPE3_PHY_RX_DIGITAL_MODES		0x00000028
+#define MEM_HS_RATE_MASK		GENMASK(28, 27)
+#define MEM_HS_RATE_SHIFT		27
+#define MEM_OVRD_HS_RATE		BIT(26)
+#define MEM_OVRD_HS_RATE_SHIFT		26
 #define MEM_CDR_FASTLOCK		BIT(23)
-#define MEM_CDR_LBW			GENMASK(22, 21)
-#define MEM_CDR_STEPCNT			GENMASK(20, 19)
+#define MEM_CDR_FASTLOCK_SHIFT		23
+#define MEM_CDR_LBW_MASK		GENMASK(22, 21)
+#define MEM_CDR_LBW_SHIFT		21
+#define MEM_CDR_STEPCNT_MASK		GENMASK(20, 19)
+#define MEM_CDR_STEPCNT_SHIFT		19
 #define MEM_CDR_STL_MASK		GENMASK(18, 16)
 #define MEM_CDR_STL_SHIFT		16
 #define MEM_CDR_THR_MASK		GENMASK(15, 13)
 #define MEM_CDR_THR_SHIFT		13
 #define MEM_CDR_THR_MODE		BIT(12)
-#define MEM_CDR_CDR_2NDO_SDM_MODE	BIT(11)
-#define MEM_OVRD_HS_RATE		BIT(26)
-
-#define PCIEPHYRX_EQUALIZER		0x00000038
-#define MEM_EQLEV			GENMASK(31, 16)
-#define MEM_EQFTC			GENMASK(15, 11)
-#define MEM_EQCTL			GENMASK(10, 7)
+#define MEM_CDR_THR_MODE_SHIFT		12
+#define MEM_CDR_2NDO_SDM_MODE		BIT(11)
+#define MEM_CDR_2NDO_SDM_MODE_SHIFT	11
+
+#define PIPE3_PHY_RX_EQUALIZER		0x00000038
+#define MEM_EQLEV_MASK			GENMASK(31, 16)
+#define MEM_EQLEV_SHIFT			16
+#define MEM_EQFTC_MASK			GENMASK(15, 11)
+#define MEM_EQFTC_SHIFT			11
+#define MEM_EQCTL_MASK			GENMASK(10, 7)
 #define MEM_EQCTL_SHIFT			7
 #define MEM_OVRD_EQLEV			BIT(2)
+#define MEM_OVRD_EQLEV_SHIFT		2
 #define MEM_OVRD_EQFTC			BIT(1)
+#define MEM_OVRD_EQFTC_SHIFT		1
+
+#define SATA_PHY_RX_IO_AND_A2D_OVERRIDES	0x44
+#define MEM_CDR_LOS_SOURCE_MASK		GENMASK(10, 9)
+#define MEM_CDR_LOS_SOURCE_SHIFT	9
 
 /*
  * This is an Empirical value that works, need to confirm the actual
@@ -127,6 +149,27 @@  struct pipe3_dpll_map {
 	struct pipe3_dpll_params params;
 };
 
+struct pipe3_settings {
+	u8 ana_interface;
+	u8 ana_losd;
+	u8 dig_fastlock;
+	u8 dig_lbw;
+	u8 dig_stepcnt;
+	u8 dig_stl;
+	u8 dig_thr;
+	u8 dig_thr_mode;
+	u8 dig_2ndo_sdm_mode;
+	u8 dig_hs_rate;
+	u8 dig_ovrd_hs_rate;
+	u8 dll_trim_sel;
+	u8 dll_phint_rate;
+	u8 eq_lev;
+	u8 eq_ftc;
+	u8 eq_ctl;
+	u8 eq_ovrd_lev;
+	u8 eq_ovrd_ftc;
+};
+
 struct ti_pipe3 {
 	void __iomem		*pll_ctrl_base;
 	void __iomem		*phy_rx;
@@ -146,6 +189,7 @@  struct ti_pipe3 {
 	unsigned int		pcie_pcs_reg; /* pcs reg. index in syscon */
 	bool			sata_refclk_enabled;
 	enum pipe3_mode		mode;
+	struct pipe3_settings	settings;
 };
 
 static struct pipe3_dpll_map dpll_map_usb[] = {
@@ -171,20 +215,84 @@  static struct pipe3_dpll_map dpll_map_sata[] = {
 struct pipe3_data {
 	enum pipe3_mode mode;
 	struct pipe3_dpll_map *dpll_map;
+	struct pipe3_settings settings;
 };
 
 static struct pipe3_data data_usb = {
 	.mode = PIPE3_MODE_USBSS,
 	.dpll_map = dpll_map_usb,
+	.settings = {
+	/* DRA75x TRM Table 26-17. Preferred USB3_PHY_RX SCP Register Settings */
+		.ana_interface = INTERFACE_MODE_USBSS,
+		.ana_losd = 0xa,
+		.dig_fastlock = 1,
+		.dig_lbw = 3,
+		.dig_stepcnt = 0,
+		.dig_stl = 0x3,
+		.dig_thr = 1,
+		.dig_thr_mode = 1,
+		.dig_2ndo_sdm_mode = 0,
+		.dig_hs_rate = 0,
+		.dig_ovrd_hs_rate = 1,
+		.dll_trim_sel = 0x2,
+		.dll_phint_rate = 0x3,
+		.eq_lev = 0,
+		.eq_ftc = 0,
+		.eq_ctl = 0x9,
+		.eq_ovrd_lev = 0,
+		.eq_ovrd_ftc = 0,
+	},
 };
 
 static struct pipe3_data data_sata = {
 	.mode = PIPE3_MODE_SATA,
 	.dpll_map = dpll_map_sata,
+	.settings = {
+	/* DRA75x TRM Table 26-9. Preferred SATA_PHY_RX SCP Register Settings */
+		.ana_interface = INTERFACE_MODE_SATA_3P0,
+		.ana_losd = 0x5,
+		.dig_fastlock = 1,
+		.dig_lbw = 3,
+		.dig_stepcnt = 0,
+		.dig_stl = 0x3,
+		.dig_thr = 1,
+		.dig_thr_mode = 1,
+		.dig_2ndo_sdm_mode = 0,
+		.dig_hs_rate = 0,	/* Not in TRM preferred settings */
+		.dig_ovrd_hs_rate = 0,	/* Not in TRM preferred settings */
+		.dll_trim_sel = 0x1,
+		.dll_phint_rate = 0x2,	/* for 1.5 GHz DPLL clock */
+		.eq_lev = 0,
+		.eq_ftc = 0x1f,
+		.eq_ctl = 0,
+		.eq_ovrd_lev = 1,
+		.eq_ovrd_ftc = 1,
+	},
 };
 
 static struct pipe3_data data_pcie = {
 	.mode = PIPE3_MODE_PCIE,
+	.settings = {
+	/* DRA75x TRM Table 26-62. Preferred PCIe_PHY_RX SCP Register Settings */
+		.ana_interface = INTERFACE_MODE_PCIE,
+		.ana_losd = 0xa,
+		.dig_fastlock = 1,
+		.dig_lbw = 3,
+		.dig_stepcnt = 0,
+		.dig_stl = 0x3,
+		.dig_thr = 1,
+		.dig_thr_mode = 1,
+		.dig_2ndo_sdm_mode = 0,
+		.dig_hs_rate = 0,
+		.dig_ovrd_hs_rate = 0,
+		.dll_trim_sel = 0x2,
+		.dll_phint_rate = 0x3,
+		.eq_lev = 0,
+		.eq_ftc = 0x1f,
+		.eq_ctl = 1,
+		.eq_ovrd_lev = 0,
+		.eq_ovrd_ftc = 0,
+	},
 };
 
 static inline u32 ti_pipe3_readl(void __iomem *addr, unsigned offset)
@@ -324,32 +432,55 @@  static int ti_pipe3_dpll_program(struct ti_pipe3 *phy)
 static void ti_pipe3_calibrate(struct ti_pipe3 *phy)
 {
 	u32 val;
+	struct pipe3_settings *s = &phy->settings;
 
-	val = ti_pipe3_readl(phy->phy_rx, PCIEPHYRX_ANA_PROGRAMMABILITY);
+	val = ti_pipe3_readl(phy->phy_rx, PIPE3_PHY_RX_ANA_PROGRAMMABILITY);
 	val &= ~(INTERFACE_MASK | LOSD_MASK | MEM_PLLDIV);
-	val = (0x1 << INTERFACE_SHIFT | 0xA << LOSD_SHIFT);
-	ti_pipe3_writel(phy->phy_rx, PCIEPHYRX_ANA_PROGRAMMABILITY, val);
-
-	val = ti_pipe3_readl(phy->phy_rx, PCIEPHYRX_DIGITAL_MODES);
-	val &= ~(MEM_CDR_STEPCNT | MEM_CDR_STL_MASK | MEM_CDR_THR_MASK |
-		 MEM_CDR_CDR_2NDO_SDM_MODE | MEM_OVRD_HS_RATE);
-	val |= (MEM_CDR_FASTLOCK | MEM_CDR_LBW | 0x3 << MEM_CDR_STL_SHIFT |
-		0x1 << MEM_CDR_THR_SHIFT | MEM_CDR_THR_MODE);
-	ti_pipe3_writel(phy->phy_rx, PCIEPHYRX_DIGITAL_MODES, val);
-
-	val = ti_pipe3_readl(phy->phy_rx, PCIEPHYRX_TRIM);
-	val &= ~MEM_DLL_TRIM_SEL;
-	val |= 0x2 << MEM_DLL_TRIM_SHIFT;
-	ti_pipe3_writel(phy->phy_rx, PCIEPHYRX_TRIM, val);
-
-	val = ti_pipe3_readl(phy->phy_rx, PCIEPHYRX_DLL);
-	val |= MEM_DLL_PHINT_RATE;
-	ti_pipe3_writel(phy->phy_rx, PCIEPHYRX_DLL, val);
-
-	val = ti_pipe3_readl(phy->phy_rx, PCIEPHYRX_EQUALIZER);
-	val &= ~(MEM_EQLEV | MEM_EQCTL | MEM_OVRD_EQLEV | MEM_OVRD_EQFTC);
-	val |= MEM_EQFTC | 0x1 << MEM_EQCTL_SHIFT;
-	ti_pipe3_writel(phy->phy_rx, PCIEPHYRX_EQUALIZER, val);
+	val = (s->ana_interface << INTERFACE_SHIFT | s->ana_losd << LOSD_SHIFT);
+	ti_pipe3_writel(phy->phy_rx, PIPE3_PHY_RX_ANA_PROGRAMMABILITY, val);
+
+	val = ti_pipe3_readl(phy->phy_rx, PIPE3_PHY_RX_DIGITAL_MODES);
+	val &= ~(MEM_HS_RATE_MASK | MEM_OVRD_HS_RATE | MEM_CDR_FASTLOCK |
+		 MEM_CDR_LBW_MASK | MEM_CDR_STEPCNT_MASK | MEM_CDR_STL_MASK |
+		 MEM_CDR_THR_MASK | MEM_CDR_THR_MODE | MEM_CDR_2NDO_SDM_MODE);
+	val |= s->dig_hs_rate << MEM_HS_RATE_SHIFT |
+		s->dig_ovrd_hs_rate << MEM_OVRD_HS_RATE_SHIFT |
+		s->dig_fastlock << MEM_CDR_FASTLOCK_SHIFT |
+		s->dig_lbw << MEM_CDR_LBW_SHIFT |
+		s->dig_stepcnt << MEM_CDR_STEPCNT_SHIFT |
+		s->dig_stl << MEM_CDR_STL_SHIFT |
+		s->dig_thr << MEM_CDR_THR_SHIFT |
+		s->dig_thr_mode << MEM_CDR_THR_MODE_SHIFT |
+		s->dig_2ndo_sdm_mode << MEM_CDR_2NDO_SDM_MODE_SHIFT;
+	ti_pipe3_writel(phy->phy_rx, PIPE3_PHY_RX_DIGITAL_MODES, val);
+
+	val = ti_pipe3_readl(phy->phy_rx, PIPE3_PHY_RX_TRIM);
+	val &= ~MEM_DLL_TRIM_SEL_MASK;
+	val |= s->dll_trim_sel << MEM_DLL_TRIM_SHIFT;
+	ti_pipe3_writel(phy->phy_rx, PIPE3_PHY_RX_TRIM, val);
+
+	val = ti_pipe3_readl(phy->phy_rx, PIPE3_PHY_RX_DLL);
+	val &= ~MEM_DLL_PHINT_RATE_MASK;
+	val |= s->dll_phint_rate << MEM_DLL_PHINT_RATE_SHIFT;
+	ti_pipe3_writel(phy->phy_rx, PIPE3_PHY_RX_DLL, val);
+
+	val = ti_pipe3_readl(phy->phy_rx, PIPE3_PHY_RX_EQUALIZER);
+	val &= ~(MEM_EQLEV_MASK | MEM_EQFTC_MASK | MEM_EQCTL_MASK |
+		 MEM_OVRD_EQLEV | MEM_OVRD_EQFTC);
+	val |= s->eq_lev << MEM_EQLEV_SHIFT |
+		s->eq_ftc << MEM_EQFTC_SHIFT |
+		s->eq_ctl << MEM_EQCTL_SHIFT |
+		s->eq_ovrd_lev << MEM_OVRD_EQLEV_SHIFT |
+		s->eq_ovrd_ftc << MEM_OVRD_EQFTC_SHIFT;
+	ti_pipe3_writel(phy->phy_rx, PIPE3_PHY_RX_EQUALIZER, val);
+
+	if (phy->mode == PIPE3_MODE_SATA) {
+		val = ti_pipe3_readl(phy->phy_rx,
+				     SATA_PHY_RX_IO_AND_A2D_OVERRIDES);
+		val &= ~MEM_CDR_LOS_SOURCE_MASK;
+		ti_pipe3_writel(phy->phy_rx, SATA_PHY_RX_IO_AND_A2D_OVERRIDES,
+				val);
+	}
 }
 
 static int ti_pipe3_init(struct phy *x)
@@ -401,6 +532,8 @@  static int ti_pipe3_init(struct phy *x)
 		return -EINVAL;
 	}
 
+	ti_pipe3_calibrate(phy);
+
 	return ret;
 }
 
@@ -611,9 +744,6 @@  static int ti_pipe3_get_tx_rx_base(struct ti_pipe3 *phy)
 	struct device *dev = phy->dev;
 	struct platform_device *pdev = to_platform_device(dev);
 
-	if (phy->mode != PIPE3_MODE_PCIE)
-		return 0;
-
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
 					   "phy_rx");
 	phy->phy_rx = devm_ioremap_resource(dev, res);
@@ -669,6 +799,7 @@  static int ti_pipe3_probe(struct platform_device *pdev)
 	phy->dev = dev;
 	phy->mode = data->mode;
 	phy->dpll_map = data->dpll_map;
+	phy->settings = data->settings;
 
 	ret = ti_pipe3_get_pll_base(phy);
 	if (ret)