new file mode 100644
@@ -0,0 +1,101 @@
+* Texas Instruments - lm3532 White LED driver with ambient light sensing
+capability.
+
+The LM3532 provides the 3 high-voltage, low-side current sinks. The device is
+programmable over an I2C-compatible interface and has independent
+current control for all three channels. The adaptive current regulation
+method allows for different LED currents in each current sink thus allowing
+for a wide variety of backlight and keypad applications.
+
+The main features of the LM3532 include dual ambient light sensor inputs
+each with 32 internal voltage setting resistors, 8-bit logarithmic and linear
+brightness control, dual external PWM brightness control inputs, and up to
+1000:1 dimming ratio with programmable fade in and fade out settings.
+
+Required properties:
+ - compatible : "ti,lm3532"
+ - reg : I2C slave address
+ - #address-cells : 1
+ - #size-cells : 0
+
+Optional properties:
+ - enable-gpios : gpio pin to enable (active high)/disable the device.
+ - ramp-up-us - The Run time ramp rates/step are from one current
+ set-point to another after the device has reached its
+ initial target set point from turn-on
+ - ramp-down-us - The Run time ramp rates/step are from one current
+ set-point to another after the device has reached its
+ initial target set point from turn-on
+ Range for ramp settings: 8us - 65536us
+
+Optional properties if ALS mode is used:
+ - ti,als-vmin - Minimum ALS voltage defined in Volts
+ - ti,als-vmax - Maximum ALS voltage defined in Volts
+ Per the data sheet the max ALS voltage is 2V and the min is 0V
+
+ - ti,als1-imp-sel - ALS1 impedance resistor selection in Ohms
+ - ti,als2-imp-sel - ALS2 impedance resistor selection in Ohms
+ Range for impedance select: 37000 Ohms - 1190 Ohms
+ Values above 37kohms will be set to the "High Impedance" setting
+
+ - ti,als-avrg-time-us - Determines the length of time the device needs to
+ average the two ALS inputs. This is only used if
+ the input mode is LM3532_ALS_INPUT_AVRG.
+ Range: 17920us - 2293760us
+ - ti,als-input-mode - Determines how the device uses the attached ALS
+ devices.
+ 0x00 - ALS1 and ALS2 input average
+ 0x01 - ALS1 Input
+ 0x02 - ALS2 Input
+ 0x03 - Max of ALS1 and ALS2
+
+Required child properties:
+ - reg : Indicates control bank the LED string is controlled by
+ - led-sources : see Documentation/devicetree/bindings/leds/common.txt
+ - ti,led-mode : Defines if the LED strings are manually controlled or
+ if the LED strings are controlled by the ALS.
+ 0x00 - LED strings are I2C controlled via full scale
+ brightness control register
+ 0x01 - LED strings are ALS controlled
+
+Optional LED child properties:
+ - label : see Documentation/devicetree/bindings/leds/common.txt
+ - linux,default-trigger :
+ see Documentation/devicetree/bindings/leds/common.txt
+
+Example:
+led-controller@38 {
+ compatible = "ti,lm3532";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x38>;
+
+ enable-gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
+ ramp-up-us = <1024>;
+ ramp-down-us = <65536>;
+
+ ti,als-vmin = <0>;
+ ti,als-vmax = <2000>;
+ ti,als1-imp-sel = <4110>;
+ ti,als2-imp-sel = <2180>;
+ ti,als-avrg-time-us = <17920>;
+ ti,als-input-mode = <0x00>;
+
+ lcd_backlight: led@0 {
+ reg = <0>;
+ led-sources = <2>;
+ ti,led-mode = <1>;
+ label = "backlight";
+ linux,default-trigger = "backlight";
+ };
+
+ led@1 {
+ reg = <1>;
+ led-sources = <1>;
+ ti,led-mode = <0>;
+ label = "platform::kbd_backlight";
+ };
+};
+
+For more product information please see the links below:
+http://www.ti.com/product/LM3532
@@ -4,7 +4,6 @@ TI LMU driver supports lighting devices below.
Name Child nodes
------ ---------------------------------
- LM3532 Backlight
LM3631 Backlight and regulator
LM3632 Backlight and regulator
LM3633 Backlight, LED and fault monitor
@@ -13,7 +12,6 @@ TI LMU driver supports lighting devices below.
Required properties:
- compatible: Should be one of:
- "ti,lm3532"
"ti,lm3631"
"ti,lm3632"
"ti,lm3633"
@@ -23,7 +21,6 @@ Required properties:
0x11 for LM3632
0x29 for LM3631
0x36 for LM3633, LM3697
- 0x38 for LM3532
0x63 for LM3695
Optional property:
@@ -47,23 +44,6 @@ Optional nodes:
[2] ../leds/leds-lm3633.txt
[3] ../regulator/lm363x-regulator.txt
-lm3532@38 {
- compatible = "ti,lm3532";
- reg = <0x38>;
-
- enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>;
-
- backlight {
- compatible = "ti,lm3532-backlight";
-
- lcd {
- led-sources = <0 1 2>;
- ramp-up-msec = <30>;
- ramp-down-msec = <0>;
- };
- };
-};
-
lm3631@29 {
compatible = "ti,lm3631";
reg = <0x29>;