@@ -9,6 +9,7 @@
#include "dra74x.dtsi"
#include "dra7-evm-common.dtsi"
+#include "dra74x-mmc-iodelay.dtsi"
/ {
model = "TI DRA742";
@@ -326,8 +327,6 @@
&mmc1 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins_default>;
vmmc-supply = <&evm_3v3_sd>;
vqmmc-supply = <&ldo1_reg>;
bus-width = <4>;
@@ -336,14 +335,29 @@
* is always hardwired.
*/
cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50-rev11", "sdr104-rev11", "ddr50", "sdr104";
+ pinctrl-0 = <&mmc1_pins_default>;
+ pinctrl-1 = <&mmc1_pins_hs>;
+ pinctrl-2 = <&mmc1_pins_sdr12>;
+ pinctrl-3 = <&mmc1_pins_sdr25>;
+ pinctrl-4 = <&mmc1_pins_sdr50>;
+ pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev11_conf>;
+ pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev11_conf>;
+ pinctrl-7 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev20_conf>;
+ pinctrl-8 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>;
};
&mmc2 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_pins_default>;
vmmc-supply = <&evm_1v8_sw>;
bus-width = <8>;
+ pinctrl-names = "default", "hs", "ddr_1_8v-rev11", "ddr_1_8v", "hs200_1_8v-rev11", "hs200_1_8v";
+ pinctrl-0 = <&mmc2_pins_default>;
+ pinctrl-1 = <&mmc2_pins_hs>;
+ pinctrl-2 = <&mmc2_pins_ddr_1_8v_rev11 &mmc2_iodelay_ddr_1_8v_rev11_conf>;
+ pinctrl-3 = <&mmc2_pins_ddr_rev20>;
+ pinctrl-4 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_rev11_conf>;
+ pinctrl-5 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_rev20_conf>;
};
&cpu0 {
Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay configuration values for the various MMC modes for dra74 SoC and use it in the pinctrl properties of MMC devicetree nodes present in dra7-evm. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> --- arch/arm/boot/dts/dra7-evm.dts | 22 ++++++++++++++++++---- 1 file changed, 18 insertions(+), 4 deletions(-) -- 2.11.0