@@ -9,6 +9,7 @@
#include "dra74x.dtsi"
#include "am57xx-commercial-grade.dtsi"
+#include "dra74x-mmc-iodelay.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
@@ -166,34 +167,6 @@
};
};
-&dra7_pmx_core {
- mmc1_pins_default: mmc1_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */
- DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
- DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
- DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
- DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
- DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
- DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
- >;
- };
-
- mmc2_pins_default: mmc2_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
- DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
- DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
- DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
- DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
- DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
- DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
- DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
- DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
- DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
- >;
- };
-};
&i2c1 {
status = "okay";
clock-frequency = <400000>;
@@ -19,10 +19,25 @@
};
&mmc1 {
+ pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50", "sdr104";
+ pinctrl-0 = <&mmc1_pins_default>;
+ pinctrl-1 = <&mmc1_pins_hs>;
+ pinctrl-2 = <&mmc1_pins_sdr12>;
+ pinctrl-3 = <&mmc1_pins_sdr25>;
+ pinctrl-4 = <&mmc1_pins_sdr50>;
+ pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr_rev11_conf>;
+ pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev11_conf>;
vmmc-supply = <&vdd_3v3>;
vqmmc-supply = <&ldo1_reg>;
};
+&mmc2 {
+ pinctrl-names = "default", "hs", "ddr_1_8v";
+ pinctrl-0 = <&mmc2_pins_default>;
+ pinctrl-1 = <&mmc2_pins_hs>;
+ pinctrl-2 = <&mmc2_pins_ddr_3_3v_rev11 &mmc2_iodelay_ddr_3_3v_rev11_conf>;
+};
+
/* errata i880 "Ethernet RGMII2 Limited to 10/100 Mbps" */
&phy1 {
max-speed = <100>;
@@ -20,9 +20,20 @@
};
&mmc1 {
+ pinctrl-names = "default", "hs";
+ pinctrl-0 = <&mmc1_pins_default>;
+ pinctrl-1 = <&mmc1_pins_hs>;
+
vmmc-supply = <&ldo1_reg>;
};
+&mmc2 {
+ pinctrl-names = "default", "hs", "ddr_1_8v";
+ pinctrl-0 = <&mmc2_pins_default>;
+ pinctrl-1 = <&mmc2_pins_hs>;
+ pinctrl-2 = <&mmc2_pins_ddr_3_3v_rev11 &mmc2_iodelay_ddr_3_3v_rev11_conf>;
+};
+
/* errata i880 "Ethernet RGMII2 Limited to 10/100 Mbps" */
&phy1 {
max-speed = <100>;
Include dra74x-mmc-iodelay.dtsi which has pinmux and IODelay configuration values for the various MMC modes for dra74 SoC and use it in the pinctrl properties of MMC devicetree nodes present in am57xx-beagle-x15/am57xx-beagle-x15-revb1. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> --- arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi | 29 +------------------------ arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts | 15 +++++++++++++ arch/arm/boot/dts/am57xx-beagle-x15.dts | 11 ++++++++++ 3 files changed, 27 insertions(+), 28 deletions(-) -- 2.11.0