diff --git a/drivers/net/wireless/ti/cc33xx/conf.h b/drivers/net/wireless/ti/cc33xx/conf.h
new file mode 100644
index 000000000000..d3f5369100a0
--- /dev/null
+++ b/drivers/net/wireless/ti/cc33xx/conf.h
@@ -0,0 +1,1245 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+/* Copyright (C) 2022-2024 Texas Instruments Inc.*/
+
+#ifndef __CONF_H__
+#define __CONF_H__
+
+struct cc33xx_conf_header {
+	__le32 magic;
+	__le32 version;
+	__le32 checksum;
+} __packed;
+
+#define CC33XX_CONF_MAGIC	0x10e100ca
+#define CC33XX_CONF_VERSION	0x01070069
+#define CC33XX_CONF_MASK	0x0000ffff
+#define CC33X_CONF_SIZE	(sizeof(struct cc33xx_conf_file))
+
+enum {
+	CONF_HW_BIT_RATE_1MBPS   = BIT(1),
+	CONF_HW_BIT_RATE_2MBPS   = BIT(2),
+	CONF_HW_BIT_RATE_5_5MBPS = BIT(3),
+	CONF_HW_BIT_RATE_11MBPS  = BIT(4),
+	CONF_HW_BIT_RATE_6MBPS   = BIT(5),
+	CONF_HW_BIT_RATE_9MBPS   = BIT(6),
+	CONF_HW_BIT_RATE_12MBPS  = BIT(7),
+	CONF_HW_BIT_RATE_18MBPS  = BIT(8),
+	CONF_HW_BIT_RATE_24MBPS  = BIT(9),
+	CONF_HW_BIT_RATE_36MBPS  = BIT(10),
+	CONF_HW_BIT_RATE_48MBPS  = BIT(11),
+	CONF_HW_BIT_RATE_54MBPS  = BIT(12),
+	CONF_HW_BIT_RATE_MCS_0   = BIT(13),
+	CONF_HW_BIT_RATE_MCS_1   = BIT(14),
+	CONF_HW_BIT_RATE_MCS_2   = BIT(15),
+	CONF_HW_BIT_RATE_MCS_3   = BIT(16),
+	CONF_HW_BIT_RATE_MCS_4   = BIT(17),
+	CONF_HW_BIT_RATE_MCS_5   = BIT(18),
+	CONF_HW_BIT_RATE_MCS_6   = BIT(19),
+	CONF_HW_BIT_RATE_MCS_7   = BIT(20)
+};
+
+enum {
+	CONF_HW_RATE_INDEX_1MBPS      = 1,
+	CONF_HW_RATE_INDEX_2MBPS      = 2,
+	CONF_HW_RATE_INDEX_5_5MBPS    = 3,
+	CONF_HW_RATE_INDEX_11MBPS     = 4,
+	CONF_HW_RATE_INDEX_6MBPS      = 5,
+	CONF_HW_RATE_INDEX_9MBPS      = 6,
+	CONF_HW_RATE_INDEX_12MBPS     = 7,
+	CONF_HW_RATE_INDEX_18MBPS     = 8,
+	CONF_HW_RATE_INDEX_24MBPS     = 9,
+	CONF_HW_RATE_INDEX_36MBPS     = 10,
+	CONF_HW_RATE_INDEX_48MBPS     = 11,
+	CONF_HW_RATE_INDEX_54MBPS     = 12,
+	CONF_HW_RATE_INDEX_MCS0       = 13,
+	CONF_HW_RATE_INDEX_MCS1       = 14,
+	CONF_HW_RATE_INDEX_MCS2       = 15,
+	CONF_HW_RATE_INDEX_MCS3       = 16,
+	CONF_HW_RATE_INDEX_MCS4       = 17,
+	CONF_HW_RATE_INDEX_MCS5       = 18,
+	CONF_HW_RATE_INDEX_MCS6       = 19,
+	CONF_HW_RATE_INDEX_MCS7       = 20,
+
+	CONF_HW_RATE_INDEX_MAX        = CONF_HW_RATE_INDEX_MCS7,
+};
+
+enum {
+	CONF_PREAMBLE_TYPE_SHORT	= 0,
+	CONF_PREAMBLE_TYPE_LONG		= 1,
+	CONF_PREAMBLE_TYPE_OFDM		= 2,
+	CONF_PREAMBLE_TYPE_N_MIXED_MODE	= 3,
+	CONF_PREAMBLE_TYPE_GREENFIELD	= 4,
+	CONF_PREAMBLE_TYPE_AX_SU	= 5,
+	CONF_PREAMBLE_TYPE_AX_MU	= 6,
+	CONF_PREAMBLE_TYPE_AX_SU_ER	= 7,
+	CONF_PREAMBLE_TYPE_AX_TB	= 8,
+	CONF_PREAMBLE_TYPE_AX_TB_NDP_FB	= 9,
+	CONF_PREAMBLE_TYPE_AC_VHT	= 10,
+	CONF_PREAMBLE_TYPE_BE_EHT_MU	= 13,
+	CONF_PREAMBLE_TYPE_BE_EHT_TB	= 14,
+	CONF_PREAMBLE_TYPE_INVALID	= 0xFF
+};
+
+#define CONF_HW_RXTX_RATE_UNSUPPORTED 0xff
+
+enum conf_rx_queue_type {
+	CONF_RX_QUEUE_TYPE_LOW_PRIORITY,  /* All except the high priority */
+	CONF_RX_QUEUE_TYPE_HIGH_PRIORITY, /* Management and voice packets */
+};
+
+struct cc33xx_clk_cfg {
+	u32 n;
+	u32 m;
+	u32 p;
+	u32 q;
+	u8 swallow;
+};
+
+struct conf_rx_settings {
+	/* The maximum amount of time, in TU, before the
+	 * firmware discards the MSDU.
+	 *
+	 * Range: 0 - 0xFFFFFFFF
+	 */
+	u32 rx_msdu_life_time;
+
+	/* Packet detection threshold in the PHY.
+	 *
+	 * FIXME: details unknown.
+	 */
+	u32 packet_detection_threshold;
+
+	/* The longest time the STA will wait to receive traffic from the AP
+	 * after a PS-poll has been transmitted.
+	 *
+	 * Range: 0 - 200000
+	 */
+	u16 ps_poll_timeout;
+	/* The longest time the STA will wait to receive traffic from the AP
+	 * after a frame has been sent from an UPSD enabled queue.
+	 *
+	 * Range: 0 - 200000
+	 */
+	u16 upsd_timeout;
+
+	/* The number of octets in an MPDU, below which an RTS/CTS
+	 * handshake is not performed.
+	 *
+	 * Range: 0 - 4096
+	 */
+	u16 rts_threshold;
+
+	/* The RX Clear Channel Assessment threshold in the PHY
+	 * (the energy threshold).
+	 *
+	 * Range: ENABLE_ENERGY_D  == 0x140A
+	 *        DISABLE_ENERGY_D == 0xFFEF
+	 */
+	u16 rx_cca_threshold;
+
+	/* Occupied Rx mem-blocks number which requires interrupting the host
+	 * (0 = no buffering, 0xffff = disabled).
+	 *
+	 * Range: uint16_t
+	 */
+	u16 irq_blk_threshold;
+
+	/* Rx packets number which requires interrupting the host
+	 * (0 = no buffering).
+	 *
+	 * Range: uint16_t
+	 */
+	u16 irq_pkt_threshold;
+
+	/* Max time in msec the FW may delay RX-Complete interrupt.
+	 *
+	 * Range: 1 - 100
+	 */
+	u16 irq_timeout;
+
+	/* The RX queue type.
+	 *
+	 * Range: RX_QUEUE_TYPE_RX_LOW_PRIORITY, RX_QUEUE_TYPE_RX_HIGH_PRIORITY,
+	 */
+	u8 queue_type;
+} __packed;
+
+#define CONF_TX_MAX_RATE_CLASSES       10
+
+#define CONF_TX_RATE_MASK_UNSPECIFIED  0
+#define CONF_TX_RATE_MASK_BASIC        (CONF_HW_BIT_RATE_1MBPS | \
+					CONF_HW_BIT_RATE_2MBPS)
+#define CONF_TX_RATE_RETRY_LIMIT       10
+
+/* basic rates for p2p operations (probe req/resp, etc.) */
+#define CONF_TX_RATE_MASK_BASIC_P2P    CONF_HW_BIT_RATE_6MBPS
+
+/* Rates supported for data packets when operating as STA/AP. Note the absence
+ * of the 22Mbps rate. There is a FW limitation on 12 rates so we must drop
+ * one. The rate dropped is not mandatory under any operating mode.
+ */
+#define CONF_TX_ENABLED_RATES       (CONF_HW_BIT_RATE_1MBPS |    \
+	CONF_HW_BIT_RATE_2MBPS | CONF_HW_BIT_RATE_5_5MBPS |      \
+	CONF_HW_BIT_RATE_6MBPS | CONF_HW_BIT_RATE_9MBPS |        \
+	CONF_HW_BIT_RATE_11MBPS | CONF_HW_BIT_RATE_12MBPS |      \
+	CONF_HW_BIT_RATE_18MBPS | CONF_HW_BIT_RATE_24MBPS |      \
+	CONF_HW_BIT_RATE_36MBPS | CONF_HW_BIT_RATE_48MBPS |      \
+	CONF_HW_BIT_RATE_54MBPS)
+
+#define CONF_TX_CCK_RATES  (CONF_HW_BIT_RATE_1MBPS |		\
+	CONF_HW_BIT_RATE_2MBPS | CONF_HW_BIT_RATE_5_5MBPS |	\
+	CONF_HW_BIT_RATE_11MBPS)
+
+#define CONF_TX_OFDM_RATES (CONF_HW_BIT_RATE_6MBPS |             \
+	CONF_HW_BIT_RATE_12MBPS | CONF_HW_BIT_RATE_24MBPS |      \
+	CONF_HW_BIT_RATE_36MBPS | CONF_HW_BIT_RATE_48MBPS |      \
+	CONF_HW_BIT_RATE_54MBPS)
+
+#define CONF_TX_MCS_RATES (CONF_HW_BIT_RATE_MCS_0 |              \
+	CONF_HW_BIT_RATE_MCS_1 | CONF_HW_BIT_RATE_MCS_2 |        \
+	CONF_HW_BIT_RATE_MCS_3 | CONF_HW_BIT_RATE_MCS_4 |        \
+	CONF_HW_BIT_RATE_MCS_5 | CONF_HW_BIT_RATE_MCS_6 |        \
+	CONF_HW_BIT_RATE_MCS_7)
+
+/* Default rates for management traffic when operating in AP mode. This
+ * should be configured according to the basic rate set of the AP
+ */
+#define CONF_TX_AP_DEFAULT_MGMT_RATES  (CONF_HW_BIT_RATE_1MBPS | \
+	CONF_HW_BIT_RATE_2MBPS | CONF_HW_BIT_RATE_5_5MBPS)
+
+/* default rates for working as IBSS (11b and OFDM) */
+#define CONF_TX_IBSS_DEFAULT_RATES  (CONF_HW_BIT_RATE_1MBPS |       \
+		CONF_HW_BIT_RATE_2MBPS | CONF_HW_BIT_RATE_5_5MBPS | \
+		CONF_HW_BIT_RATE_11MBPS | CONF_TX_OFDM_RATES)
+
+struct conf_tx_rate_class {
+	/* The rates enabled for this rate class.
+	 *
+	 * Range: CONF_HW_BIT_RATE_* bit mask
+	 */
+	u32 enabled_rates;
+
+	/* The dot11 short retry limit used for TX retries.
+	 *
+	 * Range: uint8_t
+	 */
+	u8 short_retry_limit;
+
+	/* The dot11 long retry limit used for TX retries.
+	 *
+	 * Range: uint8_t
+	 */
+	u8 long_retry_limit;
+
+	/* Flags controlling the attributes of TX transmission.
+	 *
+	 * Range: bit 0: Truncate - when set, FW attempts to send a frame stop
+	 *               when the total valid per-rate attempts have
+	 *               been exhausted; otherwise transmissions
+	 *               will continue at the lowest available rate
+	 *               until the appropriate one of the
+	 *               short_retry_limit, long_retry_limit,
+	 *               dot11_max_transmit_msdu_life_time, or
+	 *               max_tx_life_time, is exhausted.
+	 *            1: Preamble Override - indicates if the preamble type
+	 *               should be used in TX.
+	 *            2: Preamble Type - the type of the preamble to be used by
+	 *               the policy (0 - long preamble, 1 - short preamble.
+	 */
+	u8 aflags;
+} __packed;
+
+#define CONF_TX_MAX_AC_COUNT 4
+
+/* Slot number setting to start transmission at PIFS interval */
+#define CONF_TX_AIFS_PIFS 1
+/* Slot number setting to start transmission at DIFS interval normal
+ * DCF access
+ */
+#define CONF_TX_AIFS_DIFS 2
+
+enum conf_tx_ac {
+	CONF_TX_AC_BE = 0,         /* best effort / legacy */
+	CONF_TX_AC_BK = 1,         /* background */
+	CONF_TX_AC_VI = 2,         /* video */
+	CONF_TX_AC_VO = 3,         /* voice */
+	CONF_TX_AC_CTS2SELF = 4,   /* fictitious AC, follows AC_VO */
+	CONF_TX_AC_ANY_TID = 0xff
+};
+
+struct conf_sig_weights {
+	/* RSSI from beacons average weight.
+	 *
+	 * Range: uint8_t
+	 */
+	u8 rssi_bcn_avg_weight;
+
+	/* RSSI from data average weight.
+	 *
+	 * Range: uint8_t
+	 */
+	u8 rssi_pkt_avg_weight;
+
+	/* SNR from beacons average weight.
+	 *
+	 * Range: uint8_t
+	 */
+	u8 snr_bcn_avg_weight;
+
+	/* SNR from data average weight.
+	 *
+	 * Range: uint8_t
+	 */
+	u8 snr_pkt_avg_weight;
+} __packed;
+
+struct conf_tx_ac_category {
+	/* The AC class identifier.
+	 *
+	 * Range: enum conf_tx_ac
+	 */
+	u8 ac;
+
+	/* The contention window minimum size (in slots) for the access
+	 * class.
+	 *
+	 * Range: uint8_t
+	 */
+	u8 cw_min;
+
+	/* The contention window maximum size (in slots) for the access
+	 * class.
+	 *
+	 * Range: uint8_t
+	 */
+	u16 cw_max;
+
+	/* The AIF value (in slots) for the access class.
+	 *
+	 * Range: uint8_t
+	 */
+	u8 aifsn;
+
+	/* The TX Op Limit (in microseconds) for the access class.
+	 *
+	 * Range: uint16_t
+	 */
+	u16 tx_op_limit;
+
+	/* Is the MU EDCA configured
+	 *
+	 * Range: uint8_t
+	 */
+	u8 is_mu_edca;
+
+	/*  The AIFSN value for the corresonding access class
+	 *
+	 * Range: uint8_t
+	 */
+	u8 mu_edca_aifs;
+
+	/* The ECWmin and ECWmax value is indicating contention window maximum
+	 * size (in slots) for the access
+	 *
+	 * Range: uint8_t
+	 */
+	u8 mu_edca_ecw_min_max;
+
+	/* The MU EDCA timer (in microseconds) obtaining an EDCA TXOP
+	 * for STA using MU EDCA parameters
+	 *
+	 * Range: uint8_t
+	 */
+	u8 mu_edca_timer;
+} __packed;
+
+#define CONF_TX_MAX_TID_COUNT 8
+
+/* Allow TX BA on all TIDs but 6,7. These are currently reserved in the FW */
+#define CONF_TX_BA_ENABLED_TID_BITMAP 0x3F
+
+enum {
+	CONF_CHANNEL_TYPE_DCF = 0,   /* DC/LEGACY*/
+	CONF_CHANNEL_TYPE_EDCF = 1,  /* EDCA*/
+	CONF_CHANNEL_TYPE_HCCA = 2,  /* HCCA*/
+};
+
+enum {
+	CONF_PS_SCHEME_LEGACY = 0,
+	CONF_PS_SCHEME_UPSD_TRIGGER = 1,
+	CONF_PS_SCHEME_LEGACY_PSPOLL = 2,
+	CONF_PS_SCHEME_SAPSD = 3,
+};
+
+enum {
+	CONF_ACK_POLICY_LEGACY = 0,
+	CONF_ACK_POLICY_NO_ACK = 1,
+	CONF_ACK_POLICY_BLOCK = 2,
+};
+
+struct conf_tx_tid {
+	u8 queue_id;
+	u8 channel_type;
+	u8 tsid;
+	u8 ps_scheme;
+	u8 ack_policy;
+	u32 apsd_conf[2];
+} __packed;
+
+struct conf_tx_settings {
+	/* The TX ED value for TELEC Enable/Disable.
+	 *
+	 * Range: 0, 1
+	 */
+	u8 tx_energy_detection;
+
+	/* Configuration for rate classes for TX (currently only one
+	 * rate class supported). Used in non-AP mode.
+	 */
+	struct conf_tx_rate_class sta_rc_conf;
+
+	/* Configuration for access categories for TX rate control.
+	 */
+	u8 ac_conf_count;
+	/*struct conf_tx_ac_category ac_conf[CONF_TX_MAX_AC_COUNT];*/
+	struct conf_tx_ac_category ac_conf0;
+	struct conf_tx_ac_category ac_conf1;
+	struct conf_tx_ac_category ac_conf2;
+	struct conf_tx_ac_category ac_conf3;
+
+	/* AP-mode - allow this number of TX retries to a station before an
+	 * event is triggered from FW.
+	 * In AP-mode the hlids of unreachable stations are given in the
+	 * "sta_tx_retry_exceeded" member in the event mailbox.
+	 */
+	u8 max_tx_retries;
+
+	/* AP-mode - after this number of seconds a connected station is
+	 * considered inactive.
+	 */
+	u16 ap_aging_period;
+
+	/* Configuration for TID parameters.
+	 */
+	u8 tid_conf_count;
+	/* struct conf_tx_tid tid_conf[]; */
+	struct conf_tx_tid tid_conf0;
+	struct conf_tx_tid tid_conf1;
+	struct conf_tx_tid tid_conf2;
+	struct conf_tx_tid tid_conf3;
+	struct conf_tx_tid tid_conf4;
+	struct conf_tx_tid tid_conf5;
+	struct conf_tx_tid tid_conf6;
+	struct conf_tx_tid tid_conf7;
+
+	/* The TX fragmentation threshold.
+	 *
+	 * Range: uint16_t
+	 */
+	u16 frag_threshold;
+
+	/* Max time in msec the FW may delay frame TX-Complete interrupt.
+	 *
+	 * Range: uint16_t
+	 */
+	u16 tx_compl_timeout;
+
+	/* Completed TX packet count which requires to issue the TX-Complete
+	 * interrupt.
+	 *
+	 * Range: uint16_t
+	 */
+	u16 tx_compl_threshold;
+
+	/* The rate used for control messages and scanning on the 2.4GHz band
+	 *
+	 * Range: CONF_HW_BIT_RATE_* bit mask
+	 */
+	u32 basic_rate;
+
+	/* The rate used for control messages and scanning on the 5GHz band
+	 *
+	 * Range: CONF_HW_BIT_RATE_* bit mask
+	 */
+	u32 basic_rate_5;
+
+	/* TX retry limits for templates
+	 */
+	u8 tmpl_short_retry_limit;
+	u8 tmpl_long_retry_limit;
+
+	/* Time in ms for Tx watchdog timer to expire */
+	u32 tx_watchdog_timeout;
+
+	/* when a slow link has this much packets pending, it becomes a low
+	 * priority link, scheduling-wise
+	 */
+	u8 slow_link_thold;
+
+	/* when a fast link has this much packets pending, it becomes a low
+	 * priority link, scheduling-wise
+	 */
+	u8 fast_link_thold;
+} __packed;
+
+enum {
+	CONF_WAKE_UP_EVENT_BEACON    = 0x00, /* Wake on every Beacon */
+	CONF_WAKE_UP_EVENT_DTIM      = 0x01, /* Wake on every DTIM */
+	CONF_WAKE_UP_EVENT_N_DTIM    = 0x02, /* Wake every Nth DTIM */
+	CONF_WAKE_UP_EVENT_LIMIT     = CONF_WAKE_UP_EVENT_N_DTIM,
+	/* Not supported: */
+	CONF_WAKE_UP_EVENT_N_BEACONS = 0x03, /* Wake every Nth beacon */
+	CONF_WAKE_UP_EVENT_BITS_MASK = 0x0F
+};
+
+#define CONF_MAX_BCN_FILT_IE_COUNT 32
+
+#define CONF_BCN_RULE_PASS_ON_CHANGE         BIT(0)
+#define CONF_BCN_RULE_PASS_ON_APPEARANCE     BIT(1)
+
+#define CONF_BCN_IE_OUI_LEN    3
+#define CONF_BCN_IE_VER_LEN    2
+
+struct conf_bcn_filt_rule {
+	/* IE number to which to associate a rule.
+	 *
+	 * Range: uint8_t
+	 */
+	u8 ie;
+
+	/* Rule to associate with the specific ie.
+	 *
+	 * Range: CONF_BCN_RULE_PASS_ON_*
+	 */
+	u8 rule;
+
+	/* OUI for the vendor specifie IE (221)
+	 */
+	u8 oui[3];
+
+	/* Type for the vendor specifie IE (221)
+	 */
+	u8 type;
+
+	/* Version for the vendor specifie IE (221)
+	 */
+	u8 version[2];
+} __packed;
+
+enum conf_bcn_filt_mode {
+	CONF_BCN_FILT_MODE_DISABLED = 0,
+	CONF_BCN_FILT_MODE_ENABLED = 1
+};
+
+enum conf_bet_mode {
+	CONF_BET_MODE_DISABLE = 0,
+	CONF_BET_MODE_ENABLE = 1,
+};
+
+struct conf_conn_settings {
+	/* Enable or disable the beacon filtering.
+	 *
+	 * Range: CONF_BCN_FILT_MODE_*
+	 */
+	u8 bcn_filt_mode;
+
+	/* Configure Beacon filter pass-thru rules.
+	 */
+	u8 bcn_filt_ie_count;
+	/*struct conf_bcn_filt_rule bcn_filt_ie[CONF_MAX_BCN_FILT_IE_COUNT];*/
+	/* struct conf_bcn_filt_rule bcn_filt_ie[32]; */
+	struct conf_bcn_filt_rule bcn_filt_ie0;
+	struct conf_bcn_filt_rule bcn_filt_ie1;
+	struct conf_bcn_filt_rule bcn_filt_ie2;
+	struct conf_bcn_filt_rule bcn_filt_ie3;
+	struct conf_bcn_filt_rule bcn_filt_ie4;
+	struct conf_bcn_filt_rule bcn_filt_ie5;
+	struct conf_bcn_filt_rule bcn_filt_ie6;
+	struct conf_bcn_filt_rule bcn_filt_ie7;
+	struct conf_bcn_filt_rule bcn_filt_ie8;
+	struct conf_bcn_filt_rule bcn_filt_ie9;
+	struct conf_bcn_filt_rule bcn_filt_ie10;
+	struct conf_bcn_filt_rule bcn_filt_ie11;
+	struct conf_bcn_filt_rule bcn_filt_ie12;
+	struct conf_bcn_filt_rule bcn_filt_ie13;
+	struct conf_bcn_filt_rule bcn_filt_ie14;
+	struct conf_bcn_filt_rule bcn_filt_ie15;
+	struct conf_bcn_filt_rule bcn_filt_ie16;
+	struct conf_bcn_filt_rule bcn_filt_ie17;
+	struct conf_bcn_filt_rule bcn_filt_ie18;
+	struct conf_bcn_filt_rule bcn_filt_ie19;
+	struct conf_bcn_filt_rule bcn_filt_ie20;
+	struct conf_bcn_filt_rule bcn_filt_ie21;
+	struct conf_bcn_filt_rule bcn_filt_ie22;
+	struct conf_bcn_filt_rule bcn_filt_ie23;
+	struct conf_bcn_filt_rule bcn_filt_ie24;
+	struct conf_bcn_filt_rule bcn_filt_ie25;
+	struct conf_bcn_filt_rule bcn_filt_ie26;
+	struct conf_bcn_filt_rule bcn_filt_ie27;
+	struct conf_bcn_filt_rule bcn_filt_ie28;
+	struct conf_bcn_filt_rule bcn_filt_ie29;
+	struct conf_bcn_filt_rule bcn_filt_ie30;
+	struct conf_bcn_filt_rule bcn_filt_ie31;
+
+	/* The number of consecutive beacons to lose, before the firmware
+	 * becomes out of synch.
+	 *
+	 * Range: uint32_t
+	 */
+	u32 synch_fail_thold;
+
+	/* After out-of-synch, the number of TU's to wait without a further
+	 * received beacon (or probe response) before issuing the BSS_EVENT_LOSE
+	 * event.
+	 *
+	 * Range: uint32_t
+	 */
+	u32 bss_lose_timeout;
+
+	/* Beacon receive timeout.
+	 *
+	 * Range: uint32_t
+	 */
+	u32 beacon_rx_timeout;
+
+	/* Broadcast receive timeout.
+	 *
+	 * Range: uint32_t
+	 */
+	u32 broadcast_timeout;
+
+	/* Enable/disable reception of broadcast packets in power save mode
+	 *
+	 * Range: 1 - enable, 0 - disable
+	 */
+	u8 rx_broadcast_in_ps;
+
+	/* Consecutive PS Poll failures before sending event to driver
+	 *
+	 * Range: uint8_t
+	 */
+	u8 ps_poll_threshold;
+
+	/* Configuration of signal average weights.
+	 */
+	struct conf_sig_weights sig_weights;
+
+	/* Specifies if beacon early termination procedure is enabled or
+	 * disabled.
+	 *
+	 * Range: CONF_BET_MODE_*
+	 */
+	u8 bet_enable;
+
+	/* Specifies the maximum number of consecutive beacons that may be
+	 * early terminated. After this number is reached at least one full
+	 * beacon must be correctly received in FW before beacon ET
+	 * resumes.
+	 *
+	 * Range 0 - 255
+	 */
+	u8 bet_max_consecutive;
+
+	/* Specifies the maximum number of times to try PSM entry if it fails
+	 * (if sending the appropriate null-func message fails.)
+	 *
+	 * Range 0 - 255
+	 */
+	u8 psm_entry_retries;
+
+	/* Specifies the maximum number of times to try PSM exit if it fails
+	 * (if sending the appropriate null-func message fails.)
+	 *
+	 * Range 0 - 255
+	 */
+	u8 psm_exit_retries;
+
+	/* Specifies the maximum number of times to try transmit the PSM entry
+	 * null-func frame for each PSM entry attempt
+	 *
+	 * Range 0 - 255
+	 */
+	u8 psm_entry_nullfunc_retries;
+
+	/* Specifies the dynamic PS timeout in ms that will be used
+	 * by the FW when in AUTO_PS mode
+	 */
+	u16 dynamic_ps_timeout;
+
+	/* Specifies whether dynamic PS should be disabled and PSM forced.
+	 * This is required for certain WiFi certification tests.
+	 */
+	u8 forced_ps;
+
+	/* Specifies the interval of the connection keep-alive null-func
+	 * frame in ms.
+	 *
+	 * Range: 1000 - 3600000
+	 */
+	u32 keep_alive_interval;
+
+	/* Maximum listen interval supported by the driver in units of beacons.
+	 *
+	 * Range: uint16_t
+	 */
+	u8 max_listen_interval;
+
+	/* Default sleep authorization for a new STA interface. This determines
+	 * whether we can go to ELP.
+	 */
+	u8 sta_sleep_auth;
+
+	/* Default RX BA Activity filter configuration
+	 */
+	u8 suspend_rx_ba_activity;
+} __packed;
+
+struct conf_itrim_settings {
+	/* enable dco itrim */
+	u8 enable;
+
+	/* moderation timeout in microsecs from the last TX */
+	u32 timeout;
+} __packed;
+
+enum conf_fast_wakeup {
+	CONF_FAST_WAKEUP_ENABLE,
+	CONF_FAST_WAKEUP_DISABLE,
+};
+
+struct conf_pm_config_settings {
+	/* Host clock settling time
+	 *
+	 * Range: 0 - 30000 us
+	 */
+	u32 host_clk_settling_time;
+
+	/* Host fast wakeup support
+	 *
+	 * Range: enum conf_fast_wakeup
+	 */
+	u8 host_fast_wakeup_support;
+} __packed;
+
+struct conf_roam_trigger_settings {
+	/* The minimum interval between two trigger events.
+	 *
+	 * Range: 0 - 60000 ms
+	 */
+	u16 trigger_pacing;
+
+	/* The weight for rssi/beacon average calculation
+	 *
+	 * Range: 0 - 255
+	 */
+	u8 avg_weight_rssi_beacon;
+
+	/* The weight for rssi/data frame average calculation
+	 *
+	 * Range: 0 - 255
+	 */
+	u8 avg_weight_rssi_data;
+
+	/* The weight for snr/beacon average calculation
+	 *
+	 * Range: 0 - 255
+	 */
+	u8 avg_weight_snr_beacon;
+
+	/* The weight for snr/data frame average calculation
+	 *
+	 * Range: 0 - 255
+	 */
+	u8 avg_weight_snr_data;
+} __packed;
+
+struct conf_scan_settings {
+	/* The minimum time to wait on each channel for active scans
+	 * This value will be used whenever there's a connected interface.
+	 *
+	 * Range: uint32_t tu/1000
+	 */
+	u32 min_dwell_time_active;
+
+	/* The maximum time to wait on each channel for active scans
+	 * This value will be currently used whenever there's a
+	 * connected interface. It shouldn't exceed 30000 (~30ms) to avoid
+	 * possible interference of voip traffic going on while scanning.
+	 *
+	 * Range: uint32_t tu/1000
+	 */
+	u32 max_dwell_time_active;
+
+	/* The minimum time to wait on each channel for active scans
+	 * when it's possible to have longer scan dwell times.
+	 * Currently this is used whenever we're idle on all interfaces.
+	 * Longer dwell times improve detection of networks within a
+	 * single scan.
+	 *
+	 * Range: uint32_t tu/1000
+	 */
+	u32 min_dwell_time_active_long;
+
+	/* The maximum time to wait on each channel for active scans
+	 * when it's possible to have longer scan dwell times.
+	 * See min_dwell_time_active_long
+	 *
+	 * Range: uint32_t tu/1000
+	 */
+	u32 max_dwell_time_active_long;
+
+	/* time to wait on the channel for passive scans (in TU/1000) */
+	u32 dwell_time_passive;
+
+	/* time to wait on the channel for DFS scans (in TU/1000) */
+	u32 dwell_time_dfs;
+
+	/* Number of probe requests to transmit on each active scan channel
+	 *
+	 * Range: uint8_t
+	 */
+	u16 num_probe_reqs;
+
+	/* Scan trigger (split scan) timeout. The FW will split the scan
+	 * operation into slices of the given time and allow the FW to schedule
+	 * other tasks in between.
+	 *
+	 * Range: uint32_t Microsecs
+	 */
+	u32 split_scan_timeout;
+} __packed;
+
+struct conf_sched_scan_settings {
+	/* The base time to wait on the channel for active scans (in TU/1000).
+	 * The minimum dwell time is calculated according to this:
+	 * min_dwell_time = base + num_of_probes_to_be_sent * delta_per_probe
+	 * The maximum dwell time is calculated according to this:
+	 * max_dwell_time = min_dwell_time + max_dwell_time_delta
+	 */
+	u32 base_dwell_time;
+
+	/* The delta between the min dwell time and max dwell time for
+	 * active scans (in TU/1000s). The max dwell time is used by the FW once
+	 * traffic is detected on the channel.
+	 */
+	u32 max_dwell_time_delta;
+
+	/* Delta added to min dwell time per each probe in 2.4 GHz (TU/1000) */
+	u32 dwell_time_delta_per_probe;
+
+	/* Delta added to min dwell time per each probe in 5 GHz (TU/1000) */
+	u32 dwell_time_delta_per_probe_5;
+
+	/* time to wait on the channel for passive scans (in TU/1000) */
+	u32 dwell_time_passive;
+
+	/* time to wait on the channel for DFS scans (in TU/1000) */
+	u32 dwell_time_dfs;
+
+	/* number of probe requests to send on each channel in active scans */
+	u8 num_probe_reqs;
+
+	/* RSSI threshold to be used for filtering */
+	s8 rssi_threshold;
+
+	/* SNR threshold to be used for filtering */
+	s8 snr_threshold;
+
+	/* number of short intervals scheduled scan cycles before
+	 * switching to long intervals
+	 */
+	u8 num_short_intervals;
+
+	/* interval between each long scheduled scan cycle (in ms) */
+	u16 long_interval;
+} __packed;
+
+struct conf_ht_setting {
+	u8 rx_ba_win_size;
+	u8 tx_ba_win_size;
+	u16 inactivity_timeout;
+
+	/* bitmap of enabled TIDs for TX BA sessions */
+	u8 tx_ba_tid_bitmap;
+
+	/* DEFAULT / WIDE / SISO20 */
+	u8 mode;
+} __packed;
+
+struct conf_memory_settings {
+	/* Number of stations supported in IBSS mode */
+	u8 num_stations;
+
+	/* Number of ssid profiles used in IBSS mode */
+	u8 ssid_profiles;
+
+	/* Number of memory buffers allocated to rx pool */
+	u8 rx_block_num;
+
+	/* Minimum number of blocks allocated to tx pool */
+	u8 tx_min_block_num;
+
+	/* Disable/Enable dynamic memory */
+	u8 dynamic_memory;
+
+	/* Minimum required free tx memory blocks in order to assure optimum
+	 * performance
+	 *
+	 * Range: 0-120
+	 */
+	u8 min_req_tx_blocks;
+
+	/* Minimum required free rx memory blocks in order to assure optimum
+	 * performance
+	 *
+	 * Range: 0-120
+	 */
+	u8 min_req_rx_blocks;
+
+	/* Minimum number of mem blocks (free+used) guaranteed for TX
+	 *
+	 * Range: 0-120
+	 */
+	u8 tx_min;
+} __packed;
+
+struct conf_rx_streaming_settings {
+	/* RX Streaming duration (in msec) from last tx/rx
+	 *
+	 * Range: uint32_t
+	 */
+	u32 duration;
+
+	/* Bitmap of tids to be polled during RX streaming.
+	 * (Note: it doesn't look like it really matters)
+	 *
+	 * Range: 0x1-0xff
+	 */
+	u8 queues;
+
+	/* RX Streaming interval.
+	 * (Note:this value is also used as the rx streaming timeout)
+	 * Range: 0 (disabled), 10 - 100
+	 */
+	u8 interval;
+
+	/* enable rx streaming also when there is no coex activity
+	 */
+	u8 always;
+} __packed;
+
+struct conf_fwlog {
+	/* Continuous or on-demand */
+	u8 mode;
+
+	/* Number of memory blocks dedicated for the FW logger
+	 *
+	 * Range: 2-16, or 0 to disable the FW logger
+	 */
+	u8 mem_blocks;
+
+	/* Minimum log level threshold */
+	u8 severity;
+
+	/* Include/exclude timestamps from the log messages */
+	u8 timestamp;
+
+	/* See enum cc33xx_fwlogger_output */
+	u8 output;
+
+	/* Regulates the frequency of log messages */
+	u8 threshold;
+} __packed;
+
+#define ACX_RATE_MGMT_NUM_OF_RATES 13
+struct conf_rate_policy_settings {
+	u16 rate_retry_score;
+	u16 per_add;
+	u16 per_th1;
+	u16 per_th2;
+	u16 max_per;
+	u8 inverse_curiosity_factor;
+	u8 tx_fail_low_th;
+	u8 tx_fail_high_th;
+	u8 per_alpha_shift;
+	u8 per_add_shift;
+	u8 per_beta1_shift;
+	u8 per_beta2_shift;
+	u8 rate_check_up;
+	u8 rate_check_down;
+	u8 rate_retry_policy[13];
+} __packed;
+
+struct conf_hangover_settings {
+	u32 recover_time;
+	u8 hangover_period;
+	u8 dynamic_mode;
+	u8 early_termination_mode;
+	u8 max_period;
+	u8 min_period;
+	u8 increase_delta;
+	u8 decrease_delta;
+	u8 quiet_time;
+	u8 increase_time;
+	u8 window_size;
+} __packed;
+
+enum {
+	CLOCK_CONFIG_16_2_M	= 1,
+	CLOCK_CONFIG_16_368_M,
+	CLOCK_CONFIG_16_8_M,
+	CLOCK_CONFIG_19_2_M,
+	CLOCK_CONFIG_26_M,
+	CLOCK_CONFIG_32_736_M,
+	CLOCK_CONFIG_33_6_M,
+	CLOCK_CONFIG_38_468_M,
+	CLOCK_CONFIG_52_M,
+
+	NUM_CLOCK_CONFIGS,
+};
+
+enum cc33xx_ht_mode {
+	/* Default - use MIMO, fallback to SISO20 */
+	HT_MODE_DEFAULT = 0,
+
+	/* Wide - use SISO40 */
+	HT_MODE_WIDE = 1,
+
+	/* Use SISO20 */
+	HT_MODE_SISO20 = 2,
+};
+
+struct conf_ap_sleep_settings {
+	/* Duty Cycle (20-80% of staying Awake) for IDLE AP
+	 * (0: disable)
+	 */
+	u8 idle_duty_cycle;
+	/* Duty Cycle (20-80% of staying Awake) for Connected AP
+	 * (0: disable)
+	 */
+	u8 connected_duty_cycle;
+	/* Maximum stations that are allowed to be connected to AP
+	 *  (255: no limit)
+	 */
+	u8 max_stations_thresh;
+	/* Timeout till enabling the Sleep Mechanism after data stops
+	 * [unit: 100 msec]
+	 */
+	u8 idle_conn_thresh;
+} __packed;
+
+#define CHANNELS_COUNT 39 /* 14 2.4GHz channels, 25 5GHz channels*/
+#define PER_CHANNEL_REG_RULE_BYTES 13
+#define REG_RULES_COUNT (CHANNELS_COUNT * PER_CHANNEL_REG_RULE_BYTES) /* 507 */
+
+/* TX Power limitation for a channel, used for reg domain */
+struct conf_channel_power_limit {
+	u32 reg_lim_0;
+	u32 reg_lim_1;
+	u32 reg_lim_2;
+	u8  reg_lim_3;
+} __packed;
+
+struct conf_coex_configuration {
+	/* Work without Coex HW
+	 *
+	 * Range: 1 - YES, 0 - NO
+	 */
+	u8 disable_coex;
+	/* Yes/No Choose if External SoC entity is connected
+	 *
+	 * Range: 1 - YES, 0 - NO
+	 */
+	u8 is_ext_soc_enable;
+	/* External SoC grant polarity
+	 *
+	 * 0 - Active Low
+	 *
+	 * 1 - Active High (Default)
+	 */
+	u8 ext_soc_grant_polarity;
+	/* External SoC priority polarity
+	 *
+	 * 0 - Active Low (Default)
+	 *
+	 * 1 - Active High
+	 */
+	u8 ext_soc_priority_polarity;
+	/* External SoC request polarity
+	 *
+	 * 0 - Active Low (Default)
+	 *
+	 * 1 - Active High
+	 */
+	u8 ext_soc_request_polarity;
+	u16 ext_soc_min_grant_time;
+	u16 ext_soc_max_grant_time;
+	/* Range: 0 - 20 us
+	 */
+	u8 ext_soc_t2_time;
+
+	u8 ext_soc_to_wifi_grant_delay;
+	u8 ext_soc_to_ble_grant_delay;
+} __packed;
+
+struct conf_iomux_configuration {
+	/* For any iomux pull value:
+	 * 1: Pull up
+	 * 2: Pull down
+	 * 3: Pull disable
+	 * ff: Default value set by HW
+	 * ANY other value is invalid
+	 */
+	u8 slow_clock_in_pull_val;
+	u8 sdio_clk_pull_val;
+	u8 sdio_cmd_pull_val;
+	u8 sdio_d0_pull_val;
+	u8 sdio_d1_pull_val;
+	u8 sdio_d2_pull_val;
+	u8 sdio_d3_pull_val;
+	u8 host_irq_wl_pull_val;
+	u8 uart1_tx_pull_val;
+	u8 uart1_rx_pull_val;
+	u8 uart1_cts_pull_val;
+	u8 uart1_rts_pull_val;
+	u8 coex_priority_pull_val;
+	u8 coex_req_pull_val;
+	u8 coex_grant_pull_val;
+	u8 host_irq_ble_pull_val;
+	u8 fast_clk_req_pull_val;
+	u8 ant_sel_pull_val;
+} __packed;
+
+struct conf_ant_diversity {
+	/* First beacons after antenna switch.
+	 * In this window we asses our satisfaction from the new antenna.
+	 */
+	u8 fast_switching_window;
+
+	/* Deltas above this threshold between the curiosity score and
+	 * the average RSSI will lead to antenna switch.
+	 */
+	u8 rssi_delta_for_switching;
+
+	/* Used in the first beacons after antenna switch:
+	 * Deltas above this threshold between the average RSSI and
+	 * the curiosity score will make us switch back the antennas.
+	 */
+	u8 rssi_delta_for_fast_switching;
+
+	/* Curiosity punishment in beacon timeout after an antenna switch.
+	 */
+	u8 curiosity_punish;
+
+	/* Curiosity raise in beacon timeout not after an antenna switch.
+	 */
+	u8 curiosity_raise;
+
+	/* Used for the average RSSI punishment in beacon timeout
+	 * not after antenna switch.
+	 */
+	u8 consecutive_missed_beacons_threshold;
+
+	/* Used in the curiosity metric.
+	 */
+	u8 compensation_log;
+
+	/* Used in the average RSSI metric.
+	 */
+	u8 log_alpha;
+
+	/* Curiosity initialization score.
+	 */
+	s8 initial_curiosity;
+
+	/* MR configuration: should the AP follow the STA antenna or use the default antenna.
+	 */
+	u8 ap_follows_sta;
+
+	/* MR configuration: should the BLE follow the STA antenna or use the default antenna.
+	 */
+	u8 ble_follows_sta;
+
+	/* The antenna to use when the diversity mechanism is not in charge.
+	 */
+	u8 default_antenna;
+} __packed;
+
+struct cc33xx_core_conf {
+	u8 enable_5ghz;
+	u8 enable_ble;
+	u8 enable_at_test_debug;
+	u8 disable_beamforming_fftp;
+	u32 ble_uart_baudrate;
+	u8 enable_flow_ctrl;
+	u8 listen_interval;
+	u8 wake_up_event;
+	u8 suspend_listen_interval;
+	u8 suspend_wake_up_event;
+	u8 per_channel_power_limit[507];
+	u32 internal_slowclk_wakeup_earlier;
+	u32 internal_slowclk_open_window_longer;
+	u32 external_slowclk_wakeup_earlier;
+	u32 external_slowclk_open_window_longer;
+	struct conf_coex_configuration coex_configuration;
+	/* Prevent HW recovery. FW will remain stuck. */
+	u8 no_recovery;
+	u8 disable_logger;
+	u8 mixed_mode_support;
+	u8 sram_ldo_voltage_trimming;
+	u32 xtal_settling_time_usec;
+	struct conf_ant_diversity ant_diversity;
+	struct conf_iomux_configuration iomux_configuration;
+} __packed;
+
+struct cc33xx_mac_conf {
+	u8 ps_scheme;
+	u8 he_enable;
+	u8 ap_max_num_stations;
+} __packed;
+
+struct cc33xx_phy_conf {
+	u8 insertion_loss_2_4ghz[2];
+	u8 insertion_loss_5ghz[2];
+	u8 reserved_0[2];
+	u8 ant_gain_2_4ghz[2];
+	u8 ant_gain_5ghz[2];
+	u8 reserved_1[2];
+	u8 ble_ch_lim_1m[40];
+	u8 ble_ch_lim_2m[40];
+	u8 one_time_calibration_only;
+	u8 is_diplexer_present;
+	u8 num_of_antennas;
+	u8 reg_domain;
+	u16 calib_period;
+} __packed;
+
+struct cc33xx_host_conf {
+	struct conf_rx_settings rx;
+	struct conf_tx_settings tx;
+	struct conf_conn_settings conn;
+	struct conf_itrim_settings itrim;
+	struct conf_pm_config_settings pm_config;
+	struct conf_roam_trigger_settings roam_trigger;
+	struct conf_scan_settings scan;
+	struct conf_sched_scan_settings sched_scan;
+	struct conf_ht_setting ht;
+	struct conf_memory_settings mem;
+	struct conf_rx_streaming_settings rx_streaming;
+	struct conf_fwlog fwlog;
+	struct conf_rate_policy_settings rate;
+	struct conf_hangover_settings hangover;
+	struct conf_ap_sleep_settings ap_sleep;
+
+} __packed;
+
+struct cc33xx_conf_file {
+	struct cc33xx_conf_header header;
+	struct cc33xx_phy_conf phy;
+	struct cc33xx_mac_conf mac;
+	struct cc33xx_core_conf core;
+	struct cc33xx_host_conf host_conf;
+} __packed;
+
+#endif
