new file mode 100644
@@ -0,0 +1,803 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2012 - 2018 Microchip Technology Inc., and its subsidiaries.
+ * All rights reserved.
+ */
+
+#ifndef WILC_WLAN_IF_H
+#define WILC_WLAN_IF_H
+
+#include <linux/netdevice.h>
+#include "fw.h"
+
+/********************************************
+ *
+ * Wlan Configuration ID
+ *
+ ********************************************/
+
+enum bss_types {
+ WILC_FW_BSS_TYPE_INFRA = 0,
+ WILC_FW_BSS_TYPE_INDEPENDENT,
+ WILC_FW_BSS_TYPE_AP,
+};
+
+enum {
+ WILC_FW_OPER_MODE_B_ONLY = 0, /* 1, 2 M, otherwise 5, 11 M */
+ WILC_FW_OPER_MODE_G_ONLY, /* 6,12,24 otherwise 9,18,36,48,54 */
+ WILC_FW_OPER_MODE_G_MIXED_11B_1, /* 1,2,5.5,11 otherwise all on */
+ WILC_FW_OPER_MODE_G_MIXED_11B_2, /* 1,2,5,11,6,12,24 otherwise all on */
+};
+
+enum {
+ WILC_FW_PREAMBLE_SHORT = 0, /* Short Preamble */
+ WILC_FW_PREAMBLE_LONG = 1, /* Long Preamble */
+ WILC_FW_PREAMBLE_AUTO = 2, /* Auto Preamble Selection */
+};
+
+enum {
+ WILC_FW_PASSIVE_SCAN = 0,
+ WILC_FW_ACTIVE_SCAN = 1,
+};
+
+enum {
+ WILC_FW_NO_POWERSAVE = 0,
+ WILC_FW_MIN_FAST_PS = 1,
+ WILC_FW_MAX_FAST_PS = 2,
+ WILC_FW_MIN_PSPOLL_PS = 3,
+ WILC_FW_MAX_PSPOLL_PS = 4
+};
+
+enum chip_ps_states {
+ WILC_CHIP_WAKEDUP = 0,
+ WILC_CHIP_SLEEPING_AUTO = 1,
+ WILC_CHIP_SLEEPING_MANUAL = 2
+};
+
+enum bus_acquire {
+ WILC_BUS_ACQUIRE_ONLY = 0,
+ WILC_BUS_ACQUIRE_AND_WAKEUP = 1,
+};
+
+enum bus_release {
+ WILC_BUS_RELEASE_ONLY = 0,
+ WILC_BUS_RELEASE_ALLOW_SLEEP = 1,
+};
+
+enum {
+ WILC_FW_NO_ENCRYPT = 0,
+ WILC_FW_ENCRYPT_ENABLED = BIT(0),
+ WILC_FW_WEP = BIT(1),
+ WILC_FW_WEP_EXTENDED = BIT(2),
+ WILC_FW_WPA = BIT(3),
+ WILC_FW_WPA2 = BIT(4),
+ WILC_FW_AES = BIT(5),
+ WILC_FW_TKIP = BIT(6)
+};
+
+enum {
+ WILC_FW_SEC_NO = WILC_FW_NO_ENCRYPT,
+ WILC_FW_SEC_WEP = WILC_FW_WEP | WILC_FW_ENCRYPT_ENABLED,
+ WILC_FW_SEC_WEP_EXTENDED = WILC_FW_WEP_EXTENDED | WILC_FW_SEC_WEP,
+ WILC_FW_SEC_WPA = WILC_FW_WPA | WILC_FW_ENCRYPT_ENABLED,
+ WILC_FW_SEC_WPA_AES = WILC_FW_AES | WILC_FW_SEC_WPA,
+ WILC_FW_SEC_WPA_TKIP = WILC_FW_TKIP | WILC_FW_SEC_WPA,
+ WILC_FW_SEC_WPA2 = WILC_FW_WPA2 | WILC_FW_ENCRYPT_ENABLED,
+ WILC_FW_SEC_WPA2_AES = WILC_FW_AES | WILC_FW_SEC_WPA2,
+ WILC_FW_SEC_WPA2_TKIP = WILC_FW_TKIP | WILC_FW_SEC_WPA2
+};
+
+enum authtype {
+ WILC_FW_AUTH_OPEN_SYSTEM = 1,
+ WILC_FW_AUTH_SHARED_KEY = 2,
+ WILC_FW_AUTH_ANY = 3,
+ WILC_FW_AUTH_IEEE8021 = 5
+};
+
+enum site_survey {
+ WILC_FW_SITE_SURVEY_1CH = 0,
+ WILC_FW_SITE_SURVEY_ALL_CH = 1,
+ WILC_FW_SITE_SURVEY_OFF = 2
+};
+
+enum {
+ WILC_FW_ACK_POLICY_NORMAL = 0,
+ WILC_FW_ACK_NO_POLICY,
+};
+
+enum {
+ WILC_FW_REKEY_POLICY_DISABLE = 1,
+ WILC_FW_REKEY_POLICY_TIME_BASE,
+ WILC_FW_REKEY_POLICY_PKT_BASE,
+ WILC_FW_REKEY_POLICY_TIME_PKT_BASE
+};
+
+enum {
+ WILC_FW_FILTER_NO = 0x00,
+ WILC_FW_FILTER_AP_ONLY = 0x01,
+ WILC_FW_FILTER_STA_ONLY = 0x02
+};
+
+enum {
+ WILC_FW_11N_PROT_AUTO = 0, /* Auto */
+ WILC_FW_11N_NO_PROT, /* Do not use any protection */
+ WILC_FW_11N_PROT_ERP, /* Protect all ERP frame exchanges */
+ WILC_FW_11N_PROT_HT, /* Protect all HT frame exchanges */
+ WILC_FW_11N_PROT_GF /* Protect all GF frame exchanges */
+};
+
+enum {
+ WILC_FW_ERP_PROT_SELF_CTS,
+ WILC_FW_ERP_PROT_RTS_CTS,
+};
+
+enum {
+ WILC_FW_11N_OP_MODE_HT_MIXED = 1,
+ WILC_FW_11N_OP_MODE_HT_ONLY_20MHZ,
+ WILC_FW_11N_OP_MODE_HT_ONLY_20_40MHZ,
+};
+
+enum {
+ WILC_FW_OBBS_NONHT_NO_DETECT = 0,
+ WILC_FW_OBBS_NONHT_DETECT_ONLY = 1,
+ WILC_FW_OBBS_NONHT_DETECT_PROTECT = 2,
+ WILC_FW_OBBS_NONHT_DETECT_PROTECT_REPORT = 3,
+};
+
+enum {
+ WILC_FW_HT_PROT_RTS_CTS_NONHT = 0, /* RTS-CTS at non-HT rate */
+ WILC_FW_HT_PROT_FIRST_FRAME_NONHT, /* First frame at non-HT rate */
+ WILC_FW_HT_PROT_LSIG_TXOP, /* LSIG TXOP Protection */
+ WILC_FW_HT_PROT_FIRST_FRAME_MIXED, /* First frame at Mixed format */
+};
+
+enum {
+ WILC_FW_SMPS_MODE_STATIC = 1,
+ WILC_FW_SMPS_MODE_DYNAMIC = 2,
+ WILC_FW_SMPS_MODE_MIMO = 3, /* power save disable */
+};
+
+enum {
+ WILC_FW_TX_RATE_AUTO = 0,
+ WILC_FW_TX_RATE_MBPS_1 = 1,
+ WILC_FW_TX_RATE_MBPS_2 = 2,
+ WILC_FW_TX_RATE_MBPS_5_5 = 5,
+ WILC_FW_TX_RATE_MBPS_11 = 11,
+ WILC_FW_TX_RATE_MBPS_6 = 6,
+ WILC_FW_TX_RATE_MBPS_9 = 9,
+ WILC_FW_TX_RATE_MBPS_12 = 12,
+ WILC_FW_TX_RATE_MBPS_18 = 18,
+ WILC_FW_TX_RATE_MBPS_24 = 24,
+ WILC_FW_TX_RATE_MBPS_36 = 36,
+ WILC_FW_TX_RATE_MBPS_48 = 48,
+ WILC_FW_TX_RATE_MBPS_54 = 54
+};
+
+enum {
+ WILC_FW_DEFAULT_SCAN = 0,
+ WILC_FW_USER_SCAN = BIT(0),
+ WILC_FW_OBSS_PERIODIC_SCAN = BIT(1),
+ WILC_FW_OBSS_ONETIME_SCAN = BIT(2)
+};
+
+enum {
+ WILC_FW_ACTION_FRM_IDX = 0,
+ WILC_FW_PROBE_REQ_IDX = 1
+};
+
+enum wid_type {
+ WID_CHAR = 0,
+ WID_SHORT = 1,
+ WID_INT = 2,
+ WID_STR = 3,
+ WID_BIN_DATA = 4,
+ WID_BIN = 5,
+};
+
+struct wid {
+ u16 id;
+ enum wid_type type;
+ s32 size;
+ s8 *val;
+};
+
+enum {
+ WID_NIL = 0xffff,
+
+ /*
+ * BSS Type
+ * -----------------------------------------------------------
+ * Configuration : Infrastructure Independent Access Point
+ * Values to set : 0 1 2
+ * -----------------------------------------------------------
+ */
+ WID_BSS_TYPE = 0x0000,
+
+ /*
+ * Transmit Rate
+ * -----------------------------------------------------------
+ * Configuration : 1 2 5.5 11 6 9 12 18 24 36 48 54
+ * Values to set : 1 2 5 11 6 9 12 18 24 36 48 54
+ * -----------------------------------------------------------
+ */
+ WID_CURRENT_TX_RATE = 0x0001,
+
+ /*
+ * Channel
+ * -----------------------------------------------------------
+ * Configuration(g) : 1 2 3 4 5 6 7 8 9 10 11 12 13 14
+ * Values to set : 1 2 3 4 5 6 7 8 9 10 11 12 13 14
+ * -----------------------------------------------------------
+ */
+ WID_CURRENT_CHANNEL = 0x0002,
+
+ /*
+ * Preamble
+ * -----------------------------------------------------------
+ * Configuration : short long Auto
+ * Values to set : 0 1 2
+ * -----------------------------------------------------------
+ */
+ WID_PREAMBLE = 0x0003,
+
+ /*
+ * 11g operating mode (ignored if 11g not present)
+ * -----------------------------------------------------------
+ * Configuration : HighPerf Compat(RSet #1) Compat(RSet #2)
+ * Values to set : 1 2 3
+ * -----------------------------------------------------------
+ */
+ WID_11G_OPERATING_MODE = 0x0004,
+
+ /*
+ * Mac status (response only)
+ * -----------------------------------------------------------
+ * Configuration : disconnect connect
+ * Values to get : 0 1
+ * -----------------------------------------------------------
+ */
+ WID_STATUS = 0x0005,
+
+ /*
+ * Scan type
+ * -----------------------------------------------------------
+ * Configuration : Passive Scanning Active Scanning
+ * Values to set : 0 1
+ * -----------------------------------------------------------
+ */
+ WID_SCAN_TYPE = 0x0007,
+
+ /*
+ * Key Id (WEP default key Id)
+ * -----------------------------------------------------------
+ * Configuration : Any value between 0 to 3
+ * Values to set : Same value. Default is 0
+ * -----------------------------------------------------------
+ */
+ WID_KEY_ID = 0x0009,
+
+ /*
+ * QoS Enable
+ * -----------------------------------------------------------
+ * Configuration : QoS Disable WMM Enable
+ * Values to set : 0 1
+ * -----------------------------------------------------------
+ */
+ WID_QOS_ENABLE = 0x000A,
+
+ /*
+ * Power Management
+ * -----------------------------------------------------------
+ * Configuration : NO_POWERSAVE MIN_POWERSAVE MAX_POWERSAVE
+ * Values to set : 0 1 2
+ * -----------------------------------------------------------
+ */
+ WID_POWER_MANAGEMENT = 0x000B,
+
+ /*
+ * WEP/802 11I Configuration
+ * -----------------------------------------------------------
+ * Configuration:Disable WP40 WP104 WPA-AES WPA-TKIP RSN-AES RSN-TKIP
+ * Values (0x) : 00 03 07 29 49 31 51
+ * Configuration:WPA-AES+TKIP RSN-AES+TKIP
+ * Values (0x) : 69 71
+ * -----------------------------------------------------------
+ */
+ WID_11I_MODE = 0x000C,
+
+ /*
+ * WEP Configuration: Used in BSS STA mode only when WEP is enabled
+ * -----------------------------------------------------------
+ * Configuration : Open System Shared Key Any Type | 802.1x Auth
+ * Values (0x) : 01 02 03 | BIT2
+ * -----------------------------------------------------------
+ */
+ WID_AUTH_TYPE = 0x000D,
+
+ /*
+ * Site Survey Type
+ * -----------------------------------------------------------
+ * Configuration : Values to set
+ * Survey 1 Channel : 0
+ * survey all Channels : 1
+ * Disable Site Survey : 2
+ * -----------------------------------------------------------
+ */
+ WID_SITE_SURVEY = 0x000E,
+
+ /*
+ * Listen Interval
+ * -----------------------------------------------------------
+ * Configuration : Any value between 1 to 255
+ * Values to set : Same value. Default is 3
+ * -----------------------------------------------------------
+ */
+ WID_LISTEN_INTERVAL = 0x000F,
+
+ /*
+ * DTIM Period
+ * -----------------------------------------------------------
+ * Configuration : Any value between 1 to 255
+ * Values to set : Same value. Default is 3
+ * -----------------------------------------------------------
+ */
+ WID_DTIM_PERIOD = 0x0010,
+
+ /*
+ * ACK Policy
+ * -----------------------------------------------------------
+ * Configuration : Normal Ack No Ack
+ * Values to set : 0 1
+ * -----------------------------------------------------------
+ */
+ WID_ACK_POLICY = 0x0011,
+
+ /*
+ * Reset MAC (Set only)
+ * -----------------------------------------------------------
+ * Configuration : Don't Reset Reset No Request
+ * Values to set : 0 1 2
+ * -----------------------------------------------------------
+ */
+ WID_RESET = 0x0012,
+
+ /*
+ * Broadcast SSID Option: Setting this will adhere to "" SSID element
+ * -----------------------------------------------------------
+ * Configuration : Enable Disable
+ * Values to set : 1 0
+ * -----------------------------------------------------------
+ */
+ WID_BCAST_SSID = 0x0015,
+
+ /*
+ * Disconnect (Station)
+ * -----------------------------------------------------------
+ * Configuration : Association ID
+ * Values to set : Association ID
+ * -----------------------------------------------------------
+ */
+ WID_DISCONNECT = 0x0016,
+
+ /*
+ * 11a Tx Power Level
+ * -----------------------------------------------------------
+ * Configuration : Sets TX Power (Higher the value greater the power)
+ * Values to set : Any value between 0 and 63 (inclusive Default 48)
+ * -----------------------------------------------------------
+ */
+ WID_TX_POWER_LEVEL_11A = 0x0018,
+
+ /*
+ * Group Key Update Policy Selection
+ * -----------------------------------------------------------
+ * Configuration : Disabled timeBased packetBased timePacketBased
+ * Values to set : 1 2 3 4
+ * -----------------------------------------------------------
+ */
+ WID_REKEY_POLICY = 0x0019,
+
+ /*
+ * Allow Short Slot
+ * -----------------------------------------------------------
+ * Configuration : Disallow Short Slot Allow Short Slot
+ * (Enable Only Long Slot) (Enable Short Slot if applicable)
+ * Values to set : 0 1
+ * -----------------------------------------------------------
+ */
+ WID_SHORT_SLOT_ALLOWED = 0x001A,
+
+ WID_PHY_ACTIVE_REG = 0x001B,
+
+ /*
+ * 11b Tx Power Level
+ * -----------------------------------------------------------
+ * Configuration : Sets TX Power (Higher the value greater the power)
+ * Values to set : Any value between 0 and 63 (inclusive Default 48)
+ * -----------------------------------------------------------
+ */
+ WID_TX_POWER_LEVEL_11B = 0x001D,
+
+ /*
+ * Scan Request
+ * -----------------------------------------------------------
+ * Configuration : Request default scan
+ * Values to set : 0
+ * -----------------------------------------------------------
+ */
+ WID_START_SCAN_REQ = 0x001E,
+
+ /*
+ * Rssi (get only)
+ * -----------------------------------------------------------
+ * Configuration :
+ * Values to get : Rssi value
+ * -----------------------------------------------------------
+ */
+ WID_RSSI = 0x001F,
+
+ /*
+ * Join Request
+ * -----------------------------------------------------------
+ * Configuration : Request to join
+ * Values to set : index of scan result
+ * -----------------------------------------------------------
+ */
+ WID_JOIN_REQ = 0x0020,
+
+ WID_LINKSPEED = 0x0026,
+
+ /*
+ * Enable User Control of TX Power
+ * -----------------------------------------------------------
+ * Configuration : Disable Enable
+ * Values to set : 0 1
+ * -----------------------------------------------------------
+ */
+ WID_USER_CONTROL_ON_TX_POWER = 0x0027,
+
+ WID_MEMORY_ACCESS_8BIT = 0x0029,
+
+ /*
+ * Enable Auto RX Sensitivity feature
+ * -----------------------------------------------------------
+ * Configuration : Disable Enable
+ * Values to set : 0 1
+ * -----------------------------------------------------------
+ */
+ WID_AUTO_RX_SENSITIVITY = 0x0032,
+
+ /*
+ * Receive Buffer Based Ack
+ * -----------------------------------------------------------
+ * Configuration : Disable Enable
+ * Values to set : 0 1
+ * -----------------------------------------------------------
+ */
+ WID_DATAFLOW_CONTROL = 0x0033,
+
+ /*
+ * Scan Filter
+ * -----------------------------------------------------------
+ * Configuration : Class No filter AP only Station Only
+ * Values to set : 0 1 2
+ * Configuration : Priority High Rssi Low Rssi Detect
+ * Values to set : 0 0x4 0x0
+ * Configuration : Channel filter off filter on
+ * Values to set : 0 0x10
+ * -----------------------------------------------------------
+ */
+ WID_SCAN_FILTER = 0x0036,
+
+ /*
+ * Link Loss Threshold (measure in the beacon period)
+ * -----------------------------------------------------------
+ * Configuration : Any value between 10 and 254(Set to 255 disable)
+ * Values to set : Same value. Default is 10
+ * -----------------------------------------------------------
+ */
+ WID_LINK_LOSS_THRESHOLD = 0x0037,
+
+ WID_ABORT_RUNNING_SCAN = 0x003E,
+
+ /* NMAC Character WID list */
+ WID_WPS_START = 0x0043,
+
+ /*
+ * Protection mode for MAC
+ * -----------------------------------------------------------
+ * Configuration : Auto No protection ERP HT GF
+ * Values to set : 0 1 2 3 4
+ * -----------------------------------------------------------
+ */
+ WID_11N_PROT_MECH = 0x0080,
+
+ /*
+ * ERP Protection type for MAC
+ * -----------------------------------------------------------
+ * Configuration : Self-CTS RTS-CTS
+ * Values to set : 0 1
+ * -----------------------------------------------------------
+ */
+ WID_11N_ERP_PROT_TYPE = 0x0081,
+
+ /*
+ * HT Option Enable
+ * -----------------------------------------------------------
+ * Configuration : HT Enable HT Disable
+ * Values to set : 1 0
+ * -----------------------------------------------------------
+ */
+ WID_11N_ENABLE = 0x0082,
+
+ /*
+ * 11n Operating mode (Note that 11g operating mode will also be
+ * used in addition to this, if this is set to HT Mixed mode)
+ * -----------------------------------------------------------
+ * Configuration : HT Mixed HT Only-20MHz HT Only-20/40MHz
+ * Values to set : 1 2 3
+ * -----------------------------------------------------------
+ */
+ WID_11N_OPERATING_MODE = 0x0083,
+
+ /*
+ * 11n OBSS non-HT STA Detection flag
+ * -----------------------------------------------------------
+ * Configuration : Do not detect
+ * Values to set : 0
+ * Configuration : Detect, do not protect or report
+ * Values to set : 1
+ * Configuration : Detect, protect and do not report
+ * Values to set : 2
+ * Configuration : Detect, protect and report to other BSS
+ * Values to set : 3
+ * -----------------------------------------------------------
+ */
+ WID_11N_OBSS_NONHT_DETECTION = 0x0084,
+
+ /*
+ * 11n HT Protection Type
+ * -----------------------------------------------------------
+ * Configuration : RTS-CTS First Frame Exchange at non-HT-rate
+ * Values to set : 0 1
+ * Configuration : LSIG TXOP First Frame Exchange in Mixed Fmt
+ * Values to set : 2 3
+ * -----------------------------------------------------------
+ */
+ WID_11N_HT_PROT_TYPE = 0x0085,
+
+ /*
+ * 11n RIFS Protection Enable Flag
+ * -----------------------------------------------------------
+ * Configuration : Disable Enable
+ * Values to set : 0 1
+ * -----------------------------------------------------------
+ */
+ WID_11N_RIFS_PROT_ENABLE = 0x0086,
+
+ /*
+ * SMPS Mode
+ * -----------------------------------------------------------
+ * Configuration : Static Dynamic MIMO (Power Save Disabled)
+ * Values to set : 1 2 3
+ * -----------------------------------------------------------
+ */
+ WID_11N_SMPS_MODE = 0x0087,
+
+ /*
+ * Current transmit MCS
+ * -----------------------------------------------------------
+ * Configuration : MCS Index for data rate
+ * Values to set : 0 to 7
+ * -----------------------------------------------------------
+ */
+ WID_11N_CURRENT_TX_MCS = 0x0088,
+
+ WID_11N_PRINT_STATS = 0x0089,
+
+ /*
+ * 11n Short GI Enable Flag
+ * -----------------------------------------------------------
+ * Configuration : Disable Enable
+ * Values to set : 0 1
+ * -----------------------------------------------------------
+ */
+ WID_11N_SHORT_GI_ENABLE = 0x008D,
+
+ /*
+ * 11n RIFS Enable Flag
+ * -----------------------------------------------------------
+ * Configuration : Disable Enable
+ * Values to set : 0 1
+ * -----------------------------------------------------------
+ */
+ WID_RIFS_MODE = 0x0094,
+
+ /*
+ * TX Abort Feature
+ * -----------------------------------------------------------
+ * Configuration : Disable Self CTS Enable Self CTS
+ * Values to set : 0 1
+ * Configuration : Disable TX Abort Enable TX Abort
+ * Values to set : 2 3
+ * Configuration : Enable HW TX Abort Enable SW TX Abort
+ * Values to set : 4 5
+ * -----------------------------------------------------------
+ */
+ WID_TX_ABORT_CONFIG = 0x00A1,
+
+ WID_REG_TSSI_11B_VALUE = 0x00A6,
+ WID_REG_TSSI_11G_VALUE = 0x00A7,
+ WID_REG_TSSI_11N_VALUE = 0x00A8,
+ WID_TX_CALIBRATION = 0x00A9,
+ WID_DSCR_TSSI_11B_VALUE = 0x00AA,
+ WID_DSCR_TSSI_11G_VALUE = 0x00AB,
+ WID_DSCR_TSSI_11N_VALUE = 0x00AC,
+
+ /*
+ * Immediate Block-Ack Support
+ * -----------------------------------------------------------
+ * Configuration : Disable Enable
+ * Values to set : 0 1
+ * -----------------------------------------------------------
+ */
+ WID_11N_IMMEDIATE_BA_ENABLED = 0x00AF,
+
+ /*
+ * TXOP Disable Flag
+ * -----------------------------------------------------------
+ * Configuration : Disable Enable
+ * Values to set : 1 0
+ * -----------------------------------------------------------
+ */
+ WID_11N_TXOP_PROT_DISABLE = 0x00B0,
+
+ WID_TX_POWER_LEVEL_11N = 0x00B1,
+
+ /* Custom Character WID list */
+ /* SCAN Complete notification WID*/
+ WID_SCAN_COMPLETE = 0x00C9,
+
+ WID_DEL_BEACON = 0x00CA,
+
+ WID_LOG_TERMINAL_SWITCH = 0x00CD,
+ WID_TX_POWER = 0x00CE,
+ /* EMAC Short WID list */
+ /* RTS Threshold */
+ /*
+ * -----------------------------------------------------------
+ * Configuration : Any value between 256 to 2347
+ * Values to set : Same value. Default is 2347
+ * -----------------------------------------------------------
+ */
+ WID_RTS_THRESHOLD = 0x1000,
+
+ /*
+ * Fragmentation Threshold
+ * -----------------------------------------------------------
+ * Configuration : Any value between 256 to 2346
+ * Values to set : Same value. Default is 2346
+ * -----------------------------------------------------------
+ */
+ WID_FRAG_THRESHOLD = 0x1001,
+
+ WID_SHORT_RETRY_LIMIT = 0x1002,
+ WID_LONG_RETRY_LIMIT = 0x1003,
+ WID_BEACON_INTERVAL = 0x1006,
+ WID_MEMORY_ACCESS_16BIT = 0x1008,
+ WID_PASSIVE_SCAN_TIME = 0x100D,
+ WID_JOIN_START_TIMEOUT = 0x100F,
+ WID_ASOC_TIMEOUT = 0x1011,
+ WID_11I_PROTOCOL_TIMEOUT = 0x1012,
+ WID_EAPOL_RESPONSE_TIMEOUT = 0x1013,
+
+ /* NMAC Short WID list */
+ WID_11N_SIG_QUAL_VAL = 0x1085,
+ WID_CCA_THRESHOLD = 0x1087,
+
+ /* Custom Short WID list */
+
+ /* EMAC Integer WID list */
+ WID_FAILED_COUNT = 0x2000,
+ WID_RETRY_COUNT = 0x2001,
+ WID_MULTIPLE_RETRY_COUNT = 0x2002,
+ WID_FRAME_DUPLICATE_COUNT = 0x2003,
+ WID_ACK_FAILURE_COUNT = 0x2004,
+ WID_RECEIVED_FRAGMENT_COUNT = 0x2005,
+ WID_MCAST_RECEIVED_FRAME_COUNT = 0x2006,
+ WID_FCS_ERROR_COUNT = 0x2007,
+ WID_SUCCESS_FRAME_COUNT = 0x2008,
+ WID_HUT_TX_COUNT = 0x200A,
+ WID_TX_FRAGMENT_COUNT = 0x200B,
+ WID_TX_MULTICAST_FRAME_COUNT = 0x200C,
+ WID_RTS_SUCCESS_COUNT = 0x200D,
+ WID_RTS_FAILURE_COUNT = 0x200E,
+ WID_WEP_UNDECRYPTABLE_COUNT = 0x200F,
+ WID_REKEY_PERIOD = 0x2010,
+ WID_REKEY_PACKET_COUNT = 0x2011,
+ WID_1X_SERV_ADDR = 0x2012,
+ WID_STACK_IP_ADDR = 0x2013,
+ WID_STACK_NETMASK_ADDR = 0x2014,
+ WID_HW_RX_COUNT = 0x2015,
+ WID_MEMORY_ADDRESS = 0x201E,
+ WID_MEMORY_ACCESS_32BIT = 0x201F,
+
+ /* NMAC Integer WID list */
+ /* Custom Integer WID list */
+ WID_GET_INACTIVE_TIME = 0x2084,
+ /* EMAC String WID list */
+ WID_SSID = 0x3000,
+ WID_FIRMWARE_VERSION = 0x3001,
+ WID_OPERATIONAL_RATE_SET = 0x3002,
+ WID_BSSID = 0x3003,
+ WID_WEP_KEY_VALUE = 0x3004,
+ WID_11I_PSK = 0x3008,
+ WID_11E_P_ACTION_REQ = 0x3009,
+ WID_1X_KEY = 0x300A,
+ WID_HARDWARE_VERSION = 0x300B,
+ WID_MAC_ADDR = 0x300C,
+ WID_HUT_DEST_ADDR = 0x300D,
+ WID_PHY_VERSION = 0x300F,
+ WID_SUPP_USERNAME = 0x3010,
+ WID_SUPP_PASSWORD = 0x3011,
+ WID_SITE_SURVEY_RESULTS = 0x3012,
+ WID_RX_POWER_LEVEL = 0x3013,
+ WID_SET_STA_MAC_INACTIVE_TIME = 0x3017,
+ WID_ADD_WEP_KEY = 0x3019,
+ WID_REMOVE_WEP_KEY = 0x301A,
+ WID_ADD_PTK = 0x301B,
+ WID_ADD_RX_GTK = 0x301C,
+ WID_ADD_TX_GTK = 0x301D,
+ WID_REMOVE_KEY = 0x301E,
+ WID_ASSOC_REQ_INFO = 0x301F,
+ WID_ASSOC_RES_INFO = 0x3020,
+ WID_MANUFACTURER = 0x3026, /* Added for CAPI tool */
+ WID_MODEL_NAME = 0x3027, /* Added for CAPI tool */
+ WID_MODEL_NUM = 0x3028, /* Added for CAPI tool */
+ WID_DEVICE_NAME = 0x3029, /* Added for CAPI tool */
+
+ /* NMAC String WID list */
+ WID_SET_OPERATION_MODE = 0x3079,
+ WID_11N_P_ACTION_REQ = 0x3080,
+ WID_HUT_TEST_ID = 0x3081,
+ WID_PMKID_INFO = 0x3082,
+ WID_FIRMWARE_INFO = 0x3083,
+ WID_REGISTER_FRAME = 0x3084,
+ WID_DEL_ALL_STA = 0x3085,
+ WID_REMAIN_ON_CHAN = 0x3996,
+ WID_SSID_PROBE_REQ = 0x3997,
+ WID_JOIN_REQ_EXTENDED = 0x3998,
+
+ WID_IP_ADDRESS = 0x3999,
+
+ /* Custom String WID list */
+
+ /* EMAC Binary WID list */
+ WID_UAPSD_CONFIG = 0x4001,
+ WID_UAPSD_STATUS = 0x4002,
+ WID_WMM_AP_AC_PARAMS = 0x4003,
+ WID_WMM_STA_AC_PARAMS = 0x4004,
+ WID_NETWORK_INFO = 0x4005,
+ WID_STA_JOIN_INFO = 0x4006,
+ WID_CONNECTED_STA_LIST = 0x4007,
+
+ /* NMAC Binary WID list */
+ WID_11N_AUTORATE_TABLE = 0x4080,
+
+ WID_SCAN_CHANNEL_LIST = 0x4084,
+
+ WID_INFO_ELEMENT_PROBE = 0x4085,
+ WID_INFO_ELEMENT_ASSOCIATE = 0x4086,
+ WID_ADD_STA = 0X4087,
+ WID_REMOVE_STA = 0X4088,
+ WID_EDIT_STA = 0X4089,
+ WID_ADD_BEACON = 0x408a,
+
+ WID_SETUP_MULTICAST_FILTER = 0x408b,
+
+ /* Miscellaneous WIDs */
+ WID_ALL = 0x7FFE,
+ WID_MAX = 0xFFFF
+};
+
+#endif