deleted file mode 100644
@@ -1,96 +0,0 @@
-NXP i.MX System Controller Firmware (SCFW)
---------------------------------------------------------------------
-
-The System Controller Firmware (SCFW) is a low-level system function
-which runs on a dedicated Cortex-M core to provide power, clock, and
-resource management. It exists on some i.MX8 processors. e.g. i.MX8QM
-(QM, QP), and i.MX8QX (QXP, DX).
-
-The AP communicates with the SC using a multi-ported MU module found
-in the LSIO subsystem. The current definition of this MU module provides
-5 remote AP connections to the SC to support up to 5 execution environments
-(TZ, HV, standard Linux, etc.). The SC side of this MU module interfaces
-with the LSIO DSC IP bus. The SC firmware will communicate with this MU
-using the MSI bus.
-
-System Controller Device Node:
-============================================================
-
-The scu node with the following properties shall be under the /firmware/ node.
-
-Required properties:
--------------------
-- compatible: should be "fsl,imx-scu".
-- mbox-names: should include "tx0", "tx1", "tx2", "tx3",
- "rx0", "rx1", "rx2", "rx3";
- include "gip3" if want to support general MU interrupt.
-- mboxes: List of phandle of 4 MU channels for tx, 4 MU channels for
- rx, and 1 optional MU channel for general interrupt.
- All MU channels must be in the same MU instance.
- Cross instances are not allowed. The MU instance can only
- be one of LSIO MU0~M4 for imx8qxp and imx8qm. Users need
- to make sure use the one which is not conflict with other
- execution environments. e.g. ATF.
- Note:
- Channel 0 must be "tx0" or "rx0".
- Channel 1 must be "tx1" or "rx1".
- Channel 2 must be "tx2" or "rx2".
- Channel 3 must be "tx3" or "rx3".
- General interrupt rx channel must be "gip3".
- e.g.
- mboxes = <&lsio_mu1 0 0
- &lsio_mu1 0 1
- &lsio_mu1 0 2
- &lsio_mu1 0 3
- &lsio_mu1 1 0
- &lsio_mu1 1 1
- &lsio_mu1 1 2
- &lsio_mu1 1 3
- &lsio_mu1 3 3>;
- See Documentation/devicetree/bindings/mailbox/fsl,mu.yaml
- for detailed mailbox binding.
-
-Note: Each mu which supports general interrupt should have an alias correctly
-numbered in "aliases" node.
-e.g.
-aliases {
- mu1 = &lsio_mu1;
-};
-
-i.MX SCU Client Device Node:
-============================================================
-
-Client nodes are maintained as children of the relevant IMX-SCU device node.
-
-Example (imx8qxp):
--------------
-aliases {
- mu1 = &lsio_mu1;
-};
-
-lsio_mu1: mailbox@5d1c0000 {
- ...
- #mbox-cells = <2>;
-};
-
-firmware {
- scu {
- compatible = "fsl,imx-scu";
- mbox-names = "tx0", "tx1", "tx2", "tx3",
- "rx0", "rx1", "rx2", "rx3",
- "gip3";
- mboxes = <&lsio_mu1 0 0
- &lsio_mu1 0 1
- &lsio_mu1 0 2
- &lsio_mu1 0 3
- &lsio_mu1 1 0
- &lsio_mu1 1 1
- &lsio_mu1 1 2
- &lsio_mu1 1 3
- &lsio_mu1 3 3>;
- };
-};
-
-serial@5a060000 {
- ...
-};
new file mode 100644
@@ -0,0 +1,210 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/firmware/fsl,scu.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP i.MX System Controller Firmware (SCFW)
+
+maintainers:
+ - Dong Aisheng <aisheng.dong@nxp.com>
+
+description:
+ The System Controller Firmware (SCFW) is a low-level system function
+ which runs on a dedicated Cortex-M core to provide power, clock, and
+ resource management. It exists on some i.MX8 processors. e.g. i.MX8QM
+ (QM, QP), and i.MX8QX (QXP, DX).
+ The AP communicates with the SC using a multi-ported MU module found
+ in the LSIO subsystem. The current definition of this MU module provides
+ 5 remote AP connections to the SC to support up to 5 execution environments
+ (TZ, HV, standard Linux, etc.). The SC side of this MU module interfaces
+ with the LSIO DSC IP bus. The SC firmware will communicate with this MU
+ using the MSI bus.
+
+properties:
+ compatible:
+ const: fsl,imx-scu
+
+ clock-controller:
+ description:
+ Clock controller node that provides the clocks controlled by the SCU
+ $ref: /schemas/clock/fsl,scu-clk.yaml
+
+ ocotp:
+ description:
+ OCOTP controller node provided by the SCU
+ $ref: /schemas/nvmem/fsl,scu-ocotp.yaml
+
+ keys:
+ description:
+ Keys provided by the SCU
+ $ref: /schemas/input/fsl,scu-key.yaml
+
+ mboxes:
+ description:
+ A list of phandles of TX MU channels followed by a list of phandles of
+ RX MU channels. The list may include at the end one more optional MU
+ channel for general interrupt. The number of expected tx and rx
+ channels is 1 TX and 1 RX channels if MU instance is "fsl,imx8-mu-scu"
+ compatible, 4 TX and 4 RX channels otherwise. All MU channels must be
+ within the same MU instance. Cross instances are not allowed. The MU
+ instance can only be one of LSIO MU0~M4 for imx8qxp and imx8qm. Users
+ need to ensure that one is used that does not conflict with other
+ execution environments such as ATF.
+ oneOf:
+ - items:
+ - description: TX0 MU channel
+ - description: RX0 MU channel
+ - items:
+ - description: TX0 MU channel
+ - description: RX0 MU channel
+ - description: optional MU channel for general interrupt
+ - items:
+ - description: TX0 MU channel
+ - description: TX1 MU channel
+ - description: TX2 MU channel
+ - description: TX3 MU channel
+ - description: RX0 MU channel
+ - description: RX1 MU channel
+ - description: RX2 MU channel
+ - description: RX3 MU channel
+ - items:
+ - description: TX0 MU channel
+ - description: TX1 MU channel
+ - description: TX2 MU channel
+ - description: TX3 MU channel
+ - description: RX0 MU channel
+ - description: RX1 MU channel
+ - description: RX2 MU channel
+ - description: RX3 MU channel
+ - description: optional MU channel for general interrupt
+
+ mbox-names:
+ oneOf:
+ - items:
+ - const: tx0
+ - const: rx0
+ - items:
+ - const: tx0
+ - const: rx0
+ - const: gip3
+ - items:
+ - const: tx0
+ - const: tx1
+ - const: tx2
+ - const: tx3
+ - const: rx0
+ - const: rx1
+ - const: rx2
+ - const: rx3
+ - items:
+ - const: tx0
+ - const: tx1
+ - const: tx2
+ - const: tx3
+ - const: rx0
+ - const: rx1
+ - const: rx2
+ - const: rx3
+ - const: gip3
+
+ pinctrl:
+ description:
+ Pin controller provided by the SCU
+ $ref: /schemas/pinctrl/fsl,scu-pinctrl.yaml
+
+ power-controller:
+ description:
+ Power domains controller node that provides the power domains
+ controlled by the SCU
+ $ref: /schemas/power/fsl,scu-pd.yaml
+
+ rtc:
+ description:
+ RTC controller provided by the SCU
+ $ref: /schemas/rtc/fsl,scu-rtc.yaml
+
+ thermal-sensor:
+ description:
+ Thermal sensor provided by the SCU
+ $ref: /schemas/thermal/fsl,scu-thermal.yaml
+
+ watchdog:
+ description:
+ Watchdog controller provided by the SCU
+ $ref: /schemas/watchdog/fsl,scu-wdt.yaml
+
+required:
+ - compatible
+ - mbox-names
+ - mboxes
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/firmware/imx/rsrc.h>
+ #include <dt-bindings/input/input.h>
+ #include <dt-bindings/pinctrl/pads-imx8qxp.h>
+
+ firmware {
+ system-controller {
+ compatible = "fsl,imx-scu";
+ mbox-names = "tx0", "tx1", "tx2", "tx3",
+ "rx0", "rx1", "rx2", "rx3",
+ "gip3";
+ mboxes = <&lsio_mu1 0 0 &lsio_mu1 0 1 &lsio_mu1 0 2 &lsio_mu1 0 3
+ &lsio_mu1 1 0 &lsio_mu1 1 1 &lsio_mu1 1 2 &lsio_mu1 1 3
+ &lsio_mu1 3 3>;
+
+ clock-controller {
+ compatible = "fsl,imx8qxp-clk", "fsl,scu-clk";
+ #clock-cells = <2>;
+ };
+
+ pinctrl {
+ compatible = "fsl,imx8qxp-iomuxc";
+
+ pinctrl_lpuart0: lpuart0grp {
+ fsl,pins = <
+ IMX8QXP_UART0_RX_ADMA_UART0_RX 0x06000020
+ IMX8QXP_UART0_TX_ADMA_UART0_TX 0x06000020
+ >;
+ };
+ };
+
+ ocotp {
+ compatible = "fsl,imx8qxp-scu-ocotp";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ fec_mac0: mac@2c4 {
+ reg = <0x2c4 6>;
+ };
+ };
+
+ power-controller {
+ compatible = "fsl,imx8qxp-scu-pd", "fsl,scu-pd";
+ #power-domain-cells = <1>;
+ };
+
+ rtc {
+ compatible = "fsl,imx8qxp-sc-rtc";
+ };
+
+ keys {
+ compatible = "fsl,imx8qxp-sc-key", "fsl,imx-sc-key";
+ linux,keycodes = <KEY_POWER>;
+ };
+
+ watchdog {
+ compatible = "fsl,imx8qxp-sc-wdt", "fsl,imx-sc-wdt";
+ timeout-sec = <60>;
+ };
+
+ thermal-sensor {
+ compatible = "fsl,imx8qxp-sc-thermal", "fsl,imx-sc-thermal";
+ #thermal-sensor-cells = <1>;
+ };
+ };
+ };