@@ -22,6 +22,7 @@
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
+#include <linux/interrupt.h>
#include <linux/of.h>
#include <linux/pm.h>
#include <linux/platform_device.h>
@@ -36,6 +37,8 @@
#define WDOG_CURRENT_COUNT_REG_OFFSET 0x08
#define WDOG_COUNTER_RESTART_REG_OFFSET 0x0c
#define WDOG_COUNTER_RESTART_KICK_VALUE 0x76
+#define WDOG_INTERRUPT_STATUS_REG_OFFSET 0x10
+#define WDOG_INTERRUPT_CLEAR_REG_OFFSET 0x14
#define WDOG_COMP_PARAMS_1_REG_OFFSET 0xf4
#define WDOG_COMP_PARAMS_1_USE_FIX_TOP BIT(6)
@@ -59,6 +62,11 @@ module_param(nowayout, bool, 0);
MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started "
"(default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")");
+enum dw_wdt_rmod {
+ DW_WDT_RMOD_RESET = 1,
+ DW_WDT_RMOD_IRQ = 2
+};
+
struct dw_wdt_timeout {
u32 top_val;
unsigned int sec;
@@ -70,6 +78,7 @@ struct dw_wdt {
struct clk *clk;
struct clk *pclk;
unsigned long rate;
+ enum dw_wdt_rmod rmod;
struct dw_wdt_timeout timeouts[DW_WDT_NUM_TOPS];
struct watchdog_device wdd;
struct reset_control *rst;
@@ -86,6 +95,20 @@ static inline int dw_wdt_is_enabled(struct dw_wdt *dw_wdt)
WDOG_CONTROL_REG_WDT_EN_MASK;
}
+static void dw_wdt_update_mode(struct dw_wdt *dw_wdt, enum dw_wdt_rmod rmod)
+{
+ u32 val;
+
+ val = readl(dw_wdt->regs + WDOG_CONTROL_REG_OFFSET);
+ if (rmod == DW_WDT_RMOD_IRQ)
+ val |= WDOG_CONTROL_REG_RESP_MODE_MASK;
+ else
+ val &= ~WDOG_CONTROL_REG_RESP_MODE_MASK;
+ writel(val, dw_wdt->regs + WDOG_CONTROL_REG_OFFSET);
+
+ dw_wdt->rmod = rmod;
+}
+
static unsigned int dw_wdt_find_best_top(struct dw_wdt *dw_wdt,
unsigned int timeout, u32 *top_val)
{
@@ -145,7 +168,11 @@ static unsigned int dw_wdt_get_timeout(struct dw_wdt *dw_wdt)
break;
}
- return dw_wdt->timeouts[idx].sec;
+ /*
+ * In IRQ mode due to the two stages counter, the actual timeout is
+ * twice greater than the TOP setting.
+ */
+ return dw_wdt->timeouts[idx].sec * dw_wdt->rmod;
}
static int dw_wdt_ping(struct watchdog_device *wdd)
@@ -164,7 +191,20 @@ static int dw_wdt_set_timeout(struct watchdog_device *wdd, unsigned int top_s)
unsigned int timeout;
u32 top_val;
- timeout = dw_wdt_find_best_top(dw_wdt, top_s, &top_val);
+ /*
+ * Note IRQ mode being enabled means having a non-zero pre-timeout
+ * setup. In this case we try to find a TOP as close to the half of the
+ * requested timeout as possible since DW Watchdog IRQ mode is designed
+ * in two stages way - first timeout rises the pre-timeout interrupt,
+ * second timeout performs the system reset. So basically the effective
+ * watchdog-caused reset happens after two watchdog TOPs elapsed.
+ */
+ timeout = dw_wdt_find_best_top(dw_wdt, DIV_ROUND_UP(top_s, dw_wdt->rmod),
+ &top_val);
+ if (dw_wdt->rmod == DW_WDT_RMOD_IRQ)
+ wdd->pretimeout = timeout;
+ else
+ wdd->pretimeout = 0;
/*
* Set the new value in the watchdog. Some versions of dw_wdt
@@ -175,25 +215,47 @@ static int dw_wdt_set_timeout(struct watchdog_device *wdd, unsigned int top_s)
writel(top_val | top_val << WDOG_TIMEOUT_RANGE_TOPINIT_SHIFT,
dw_wdt->regs + WDOG_TIMEOUT_RANGE_REG_OFFSET);
+ /* Kick new TOP value into the watchdog counter if activated. */
+ if (watchdog_active(wdd))
+ dw_wdt_ping(wdd);
+
/*
* In case users set bigger timeout value than HW can support,
* kernel(watchdog_dev.c) helps to feed watchdog before
* wdd->max_hw_heartbeat_ms
*/
if (top_s * 1000 <= wdd->max_hw_heartbeat_ms)
- wdd->timeout = timeout;
+ wdd->timeout = timeout * dw_wdt->rmod;
else
wdd->timeout = top_s;
return 0;
}
+static int dw_wdt_set_pretimeout(struct watchdog_device *wdd, unsigned int req)
+{
+ struct dw_wdt *dw_wdt = to_dw_wdt(wdd);
+
+ /*
+ * We ignore actual value of the timeout passed from user-space
+ * using it as a flag whether the pretimeout functionality is intended
+ * to be activated.
+ */
+ dw_wdt_update_mode(dw_wdt, req ? DW_WDT_RMOD_IRQ : DW_WDT_RMOD_RESET);
+ dw_wdt_set_timeout(wdd, wdd->timeout);
+
+ return 0;
+}
+
static void dw_wdt_arm_system_reset(struct dw_wdt *dw_wdt)
{
u32 val = readl(dw_wdt->regs + WDOG_CONTROL_REG_OFFSET);
- /* Disable interrupt mode; always perform system reset. */
- val &= ~WDOG_CONTROL_REG_RESP_MODE_MASK;
+ /* Disable/enable interrupt mode depending on the RMOD flag. */
+ if (dw_wdt->rmod == DW_WDT_RMOD_IRQ)
+ val |= WDOG_CONTROL_REG_RESP_MODE_MASK;
+ else
+ val &= ~WDOG_CONTROL_REG_RESP_MODE_MASK;
/* Enable watchdog. */
val |= WDOG_CONTROL_REG_WDT_EN_MASK;
writel(val, dw_wdt->regs + WDOG_CONTROL_REG_OFFSET);
@@ -231,6 +293,7 @@ static int dw_wdt_restart(struct watchdog_device *wdd,
struct dw_wdt *dw_wdt = to_dw_wdt(wdd);
writel(0, dw_wdt->regs + WDOG_TIMEOUT_RANGE_REG_OFFSET);
+ dw_wdt_update_mode(dw_wdt, DW_WDT_RMOD_RESET);
if (dw_wdt_is_enabled(dw_wdt))
writel(WDOG_COUNTER_RESTART_KICK_VALUE,
dw_wdt->regs + WDOG_COUNTER_RESTART_REG_OFFSET);
@@ -246,9 +309,19 @@ static int dw_wdt_restart(struct watchdog_device *wdd,
static unsigned int dw_wdt_get_timeleft(struct watchdog_device *wdd)
{
struct dw_wdt *dw_wdt = to_dw_wdt(wdd);
+ unsigned int sec;
+ u32 val;
+
+ val = readl(dw_wdt->regs + WDOG_CURRENT_COUNT_REG_OFFSET);
+ sec = val / dw_wdt->rate;
- return readl(dw_wdt->regs + WDOG_CURRENT_COUNT_REG_OFFSET) /
- dw_wdt->rate;
+ if (dw_wdt->rmod == DW_WDT_RMOD_IRQ) {
+ val = readl(dw_wdt->regs + WDOG_INTERRUPT_STATUS_REG_OFFSET);
+ if (!val)
+ sec += wdd->pretimeout;
+ }
+
+ return sec;
}
static const struct watchdog_info dw_wdt_ident = {
@@ -257,16 +330,41 @@ static const struct watchdog_info dw_wdt_ident = {
.identity = "Synopsys DesignWare Watchdog",
};
+static const struct watchdog_info dw_wdt_pt_ident = {
+ .options = WDIOF_KEEPALIVEPING | WDIOF_SETTIMEOUT |
+ WDIOF_PRETIMEOUT | WDIOF_MAGICCLOSE,
+ .identity = "Synopsys DesignWare Watchdog",
+};
+
static const struct watchdog_ops dw_wdt_ops = {
.owner = THIS_MODULE,
.start = dw_wdt_start,
.stop = dw_wdt_stop,
.ping = dw_wdt_ping,
.set_timeout = dw_wdt_set_timeout,
+ .set_pretimeout = dw_wdt_set_pretimeout,
.get_timeleft = dw_wdt_get_timeleft,
.restart = dw_wdt_restart,
};
+static irqreturn_t dw_wdt_irq(int irq, void *devid)
+{
+ struct dw_wdt *dw_wdt = devid;
+ u32 val;
+
+ /*
+ * We don't clear the IRQ status. It's supposed to be done by the
+ * following ping operations.
+ */
+ val = readl(dw_wdt->regs + WDOG_INTERRUPT_STATUS_REG_OFFSET);
+ if (!val)
+ return IRQ_NONE;
+
+ watchdog_notify_pretimeout(&dw_wdt->wdd);
+
+ return IRQ_HANDLED;
+}
+
#ifdef CONFIG_PM_SLEEP
static int dw_wdt_suspend(struct device *dev)
{
@@ -447,6 +545,31 @@ static int dw_wdt_drv_probe(struct platform_device *pdev)
goto out_disable_pclk;
}
+ /* Enable normal reset without pre-timeout by default. */
+ dw_wdt_update_mode(dw_wdt, DW_WDT_RMOD_RESET);
+
+ /*
+ * Pre-timeout IRQ is optional, since some hardware may lack support
+ * of it. Note we must request rising-edge IRQ, since the lane is left
+ * pending either until the next watchdog kick event or up to the
+ * system reset.
+ */
+ ret = platform_get_irq_optional(pdev, 0);
+ if (ret >= 0) {
+ ret = devm_request_irq(dev, ret, dw_wdt_irq,
+ IRQF_SHARED | IRQF_TRIGGER_RISING,
+ pdev->name, dw_wdt);
+ if (ret)
+ goto out_disable_pclk;
+
+ dw_wdt->wdd.info = &dw_wdt_pt_ident;
+ } else {
+ if (ret == -EPROBE_DEFER)
+ goto out_disable_pclk;
+
+ dw_wdt->wdd.info = &dw_wdt_ident;
+ }
+
reset_control_deassert(dw_wdt->rst);
ret = dw_wdt_init_timeouts(dw_wdt, dev);
@@ -454,7 +577,6 @@ static int dw_wdt_drv_probe(struct platform_device *pdev)
goto out_disable_clk;
wdd = &dw_wdt->wdd;
- wdd->info = &dw_wdt_ident;
wdd->ops = &dw_wdt_ops;
wdd->min_timeout = dw_wdt_get_min_timeout(dw_wdt);
wdd->max_hw_heartbeat_ms = dw_wdt_get_max_timeout_ms(dw_wdt);
DW Watchdog can rise an interrupt in case if IRQ request mode is enabled and timer reaches the zero value. In this case the IRQ lane is left pending until either the next watchdog kick event (watchdog restart) or until the WDT_EOI register is read or the device/system reset. This interface can be used to implement the pre-timeout functionality optionally provided by the Linux kernel watchdog devices. IRQ mode provides a two stages timeout interface. It means the IRQ is raised when the counter reaches zero, while the system reset occurs only after subsequent timeout if the timer restart is not performed. Due to this peculiarity the pre-timeout value is actually set to the achieved hardware timeout, while the real watchdog timeout is considered to be twice as much of it. This applies a significant limitation on the pre-timeout values, so current implementation supports either zero value, which disables the pre-timeout events, or non-zero values, which imply the pre-timeout to be at least half of the current watchdog timeout. Note that we ask the interrupt controller to detect the rising-edge pre-timeout interrupts to prevent the high-level-IRQs flood, since if the pre-timeout happens, the IRQ lane will be left pending until it's cleared by the timer restart. Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org --- Changelog v2: - Rearrange SoBs. - Make the Pre-timeout IRQ being optionally supported. --- drivers/watchdog/dw_wdt.c | 138 +++++++++++++++++++++++++++++++++++--- 1 file changed, 130 insertions(+), 8 deletions(-)